scholarly journals Preliminary Analysis of a New Power Train Concept for a City Hybrid Vehicle

Designs ◽  
2021 ◽  
Vol 5 (1) ◽  
pp. 19
Author(s):  
Roberto Capata
Keyword(s):  
Gate Valve ◽  
Combustion Engine ◽  
Fluid Dynamic ◽  
Electrical Power ◽  
Real Field ◽  
Power Train ◽  
Hybrid Propulsion ◽  
Performance Point ◽  
Combustible Gases ◽  
Mechanical Decoupling

This research aims to test the feasibility of a prototype of a newly designed thermal engine for a hybrid propulsion vehicle. This study consists of the implementation of an innovative supercharger for city car internal combustion engine ICE (900 cc). The preliminary proposal presented here is to mechanically disconnect the compressor/turbine device, supporting the rotation of the compressor with a dedicated electric motor and connecting a turbine to a generator. Mechanical decoupling will allow both machines to be designed for operating closer to their maximum performance point, for most of the expected real field of operation. Specifically, the turbine is likely to have a lower rotation speed than the original group and will, therefore, be slightly larger. The advantage is that, while in the current supercharger groups the surplus at high regimes is discharged through the waste-gate valve without expanding in a turbine, in the configuration proposed, all the energy of the combustible gases is used by the turbine to generate electrical power that can be used where required. Once the motorization of the vehicle (999 cc) has been fixed, the two turbomachines will have to be studied and designed, looking where possible, for commercial components. Finally, a computational fluid dynamic CFD will be needed to verify the validity of the choice, followed by careful experimentation campaigns.

scholarly journals New Power Train Concept for a City Hybrid Vehicle

Proceedings ◽  
2020 ◽  
Vol 58 (1) ◽  
pp. 6
Author(s):  
Roberto Capata
Keyword(s):  
Gate Valve ◽  
Rotation Speed ◽  
Electrical Power ◽  
Real Field ◽  
Power Train ◽  
Hybrid Propulsion ◽  
Performance Point ◽  
Original Group ◽  
Combustible Gases ◽  
Mechanical Decoupling

This research aims to test the feasibility of a prototype of a newly designed thermal engine for a hybrid propulsion vehicle. This study consists of the implementation of an innovative supercharger for city car ICE (900cc). The preliminary proposal presented here is to mechanically disconnect the compressor/turbine device, supporting the rotation of the compressor with a dedicated electric motor and connecting a turbine to a generator. Mechanical decoupling will allow both machines to be designed for operating closer to their maximum performance point, for most of the expected real field of operation. Specifically, the turbine is likely to have a slightly lower rotation speed than the original group and will, therefore, be slightly larger. The advantage is that, while in the current supercharger groups the surplus at high regimes is discharged through the waste-gate valve without expanding in a turbine, in the configuration proposed, all the energy of the combustible gases is used by the turbine to generate electrical power that can be used where required. Once the motorization of the vehicle (999 cc) has been fixed, the two turbomachines will have to be studied and designed, looking, where possible, for commercial components. Finally, a CFD will be needed to verify the validity of the choice, followed by careful experimentation campaigns.

scholarly journals Energy Harvesting Technology for turbocompounding automotive engines with waste-gate valve

2019 ◽  
Vol 113 ◽  
pp. 03020
Author(s):  
Vittorio Usai ◽  
Silvia Marelli ◽  
Avinash Renuke ◽  
Alberto Traverso
Keyword(s):  
Fuel Consumption ◽  
Environmental Protection Agency ◽  
Gate Valve ◽  
Combustion Engine ◽  
Power Level ◽  
Electrical Power ◽  
Residual Energy ◽  
Exhaust Gas ◽  
Passenger Cars ◽  
Automotive Engines

The reduction of CO2 and, more generally, GHG (Green House Gases) emissions imposed by the European Commission (EC) and the Environmental Protection Agency (EPA) for passenger cars has driven the automotive industry to develop technological solutions to limit exhaust emissions and fuel consumption, without compromising vehicle performance and drivability. In a mid-term scenario, hybrid powertrain and Internal Combustion Engine (ICE) downsizing represent the present trend in vehicle technology to reduce fuel consumption and CO2 emissions. Concerning downsizing concept, to maintain a reasonable power level in small engines, the application of turbocharging is mandatory for both Spark Ignition (SI) and Diesel engines. Following this aspect, the possibility to recover the residual energy of the exhaust gases is becoming more and more attractive, as demonstrated by several studies around the world. One method to recover exhaust gas energy from ICEs is the adoption of turbo-compounding technology to recover sensible energy left in the exhaust gas by-passed through the waste-gate valve. In the paper, an innovative option of advanced boosting system is investigated through a bladeless micro expander, promising attractive cost-competitiveness. The numerical activity was developed on the basis of experimental data measured on a waste-gated turbocharger for downsized SI automotive engines. To this aim, mass flow rate through the by-pass valve and the turbine impeller was measured for different waste-gate settings in steady-state conditions at the turbocharger test bench of the University of Genoa. The paper shows that significant electrical power can be harvested from the waste-gate gases, up to 94 % of compressor power, contributing to fuel consumption reduction.

Naval Hybrid Power Take-Off and Power Take-In – Lessons Learnt and Future Advances

2018 ◽  
Author(s):  
M Benatmane ◽  
B Salter
Keyword(s):  
Electrical Power ◽  
Maritime Industry ◽  
Propulsion Systems ◽  
Systems Architecture ◽  
Hybrid Propulsion ◽  
Leading Role ◽  
Lessons Learnt ◽  
Marine Industry ◽  
Operational Systems ◽  
Great Pressure

With the ever tightening of budgets and legislation, new vessel builds are facing tough times.  The future maritime industry requires more efficient vessels to minimise ship operational costs with cleaner technologies that meet stringent environment regulations, reduce greenhouse gas emissions, specifically carbon emissions. Emissions reduction continues to be high on the agenda for the marine industry, it is responsible for about 2.5 percent of global greenhouse emissions1 and is under great pressure to reduce its environmental impact. With pressure comes the opportunity to incentivize innovation, developments and implementation of energy efficient measures, both design and operational. Naval propulsion systems are no different from other industries, and the industry is exploring ways to optimise propulsion and electrical power generation systems architecture for better performance and efficiency. Electric technology plays a leading role. The paper will: Provide a brief overview about the hybrid propulsion concept, with key electrical, mechanical qualities and issues. Describe different designs configurations and performances of hybrid propulsion systems from demonstrated and operational systems in the commercial and naval world. Cover the lessons learnt in technologies and controls used on such systems. Examine future architectures including energy storage and explore the benefits and the flexibility these can bringto the hybrid propulsion sphere.

Numerical study of fluid dynamic flow within an internal combustion engine cylinder

2017 ◽  
Author(s):  
Ana Marta Souza ◽  
Antônio César Valadares de Oliveira ◽  
Enrico Temporim Ribeiro ◽  
Francisco Souza ◽  
Marcelo Colombo Chiari
Keyword(s):  
Internal Combustion Engine ◽  
Combustion Engine ◽  
Numerical Study ◽  
Fluid Dynamic ◽  
Internal Combustion ◽  
Dynamic Flow ◽  
Engine Cylinder

A New Type of Gas Turbine Based-Hybrid Propulsion System: Part 1—Concept Development, Definition of Mission Parameters and Preliminary Sizing

2000 ◽  
Author(s):  
Emiliano Cioffarelli ◽  
Enrico Sciubba
Keyword(s):  
Gas Turbine ◽  
Combustion Engine ◽  
Development Program ◽  
Propulsion System ◽  
Medium Size ◽  
Passenger Cars ◽  
Worst Case ◽  
Hybrid Propulsion ◽  
Wide Range ◽  
Definition Of

Abstract A hybrid propulsion system of new conception for medium-size passenger cars is described and its preliminary design developed. The system consists of a turbogas set operating at fixed rpm, and a battery-operated electric motor that constitutes the actual “propulsor”. The battery pack is charged by the thermal engine which works in an electronically controlled on/off mode. Though the idea is not entirely new (there are some concept cars with similar characteristics), the present study has important new aspects, in that it bases the sizing of the thermal engine on the foreseen “worst case” vehicle mission (derived from available data on mileage and consumption derived from road tests and standard EEC driving mission cycles) that they can in fact be accomplished, and then proceeds to develop a control strategy that enables the vehicle to perform at its near–peak efficiency over a wide range of possible missions. To increase the driveability of the car, a variable-inlet vane system is provided for the gas turbine. After developing the mission concept, and showing via a thorough set of energy balances (integrated over various mission profiles), a preliminary sizing of the turbogas set is performed. The results of this first part of the development program show that the concept is indeed feasible, and that it has important advantages over both more traditional (Hybrid Vehicles powered by an Internal Combustion Engine) and novel (All-Electric Vehicle) propulsion systems.

SIMULATION OF HYBRID ELECTRIC VEHICLE BASED ON A SERIES DRIVE TRAIN LAYOUT

2016 ◽  
Vol 78 (6) ◽  
Author(s):  
Mohd Sabirin Rahmat ◽  
Fauzi Ahmad ◽  
Ahmad Kamal Mat Yamin ◽  
Noreffendy Tamaldin ◽  
Vimal Rau Aparow ◽  
...  
Keyword(s):  
Electric Vehicle ◽  
Hybrid Electric Vehicle ◽  
Combustion Engine ◽  
Automatic Transmission ◽  
Permanent Magnet Synchronous Motor ◽  
Drive Train ◽  
Maximum Speed ◽  
Power Train ◽  
Human In The Loop ◽  
Hybrid Electric

This paper provided a validated modeling and a simulation of a 6 degree freedom vehicle longitudinal model and drive-train component in a series hybrid electric vehicle. The 6-DOF vehicle dynamics model consisted of tire subsystems, permanent magnet synchronous motor which acted as the prime mover coupled with an automatic transmission, hydraulic brake subsystem, battery subsystem, alternator subsystem and internal combustion engine to supply the rotational input to the alternator. A speed and torque tracking control systems of the electric power train were developed to make sure that the power train was able to produce the desired throttle torque in accelerating the vehicle. A human-in-the-loop-simulation was utilized as a mechanism to evaluate the effectiveness of the proposed hybrid electric vehicle. The proposed simulation was used as the preliminary result in identifying the capability of the vehicle in terms of the maximum speed produced by the vehicle and the capability of the alternator to recharge the battery. Several tests had been done during the simulation, namely sudden acceleration, acceleration and braking test and unbounded motion. The results of the simulation showed that the proposed hybrid electric vehicle can produce a speed of up to 70 km/h with a reasonable charging rate to the battery. The findings from this study can be considered in terms of design, optimization and implementation in a real vehicle.

scholarly journals Dynamic Analysis of Electrical Power Grid Delivery: Using Prime Mover Engines to Balance Dynamic Wind Turbine Output

2011 ◽  
Author(s):  
Diana K. Grauer ◽  
Michael E. Reed
Keyword(s):  
Renewable Energy ◽  
Wind Turbine ◽  
Research Team ◽  
Combustion Engine ◽  
National Laboratory ◽  
Electrical Power ◽  
Energy System ◽  
Electrical Transmission ◽  
Reciprocating Engine ◽  
Electrical Generation

This paper presents an investigation into integrated wind + combustion engine high penetration electrical generation systems. Renewable generation systems are now a reality of electrical transmission. Unfortunately, many of these renewable energy supplies are stochastic and highly dynamic. Conversely, the existing national grid has been designed for steady state operation. The research team has developed an algorithm to investigate the feasibility and relative capability of a reciprocating internal combustion engine to directly integrate with wind generation in a tightly coupled Hybrid Energy System. Utilizing the Idaho National Laboratory developed Phoenix Model Integration Platform, the research team has coupled demand data with wind turbine generation data and the Aspen Custom Modeler reciprocating engine electrical generator model to investigate the capability of reciprocating engine electrical generation to balance stochastic renewable energy.

scholarly journals Comparative analysis of combustion engine and hybrid propulsion unit in aviation application in terms of emission of harmful compounds in the exhausts emitted to the atmosphere

2019 ◽  
Vol 178 (3) ◽  
pp. 213-217
Author(s):  
Marek ORKISZ ◽  
Piotr WYGONIK ◽  
Michał KUŹNIAR ◽  
Maciej KALWARA
Keyword(s):  
Comparative Analysis ◽  
Combustion Engine ◽  
Total Power ◽  
Exhaust Emission ◽  
Flight Trajectory ◽  
Hybrid Propulsion ◽  
Electric Generator ◽  
In Series ◽  
Propulsion Control ◽  
Propulsion Unit

Comparative analysis of combustion and hybrid propulsion unit in aviation application in terms of emission of harmful compounds in the exhausts emitted to the atmosphere. For the propulsion of the AOS 71 motor glider, two types of propulsion were planned as de-velopment versions. The first analysed propulsion is based on a combustion engine, but of the Wankel type (LCR 814 engine with the power of 55 kW). The second designed propulsion is an hybrid based on a LCR 407 combustion engine with a power of 28 kW, which is connected in series with an electric generator propelling the engine (Emrax 228 engine), total power of the propulsion is 55 kW. The comparison of emissions of harmful compounds emitted to the atmosphere generated by the combustion and hybrid power unit intended for assembly in the AOS 71 motor glider, assuming various loads and methods of hybrid propulsion control, was made. The tests were conducted in laboratory conditions. Several different programs were designed to simulate different energy management methods in a hybrid system, depending on the predicted mission and load of the motor glider. On the basis of laboratory tests, exhaust emission was determined from both propulsions as a function of rotational speed and load. Then, based on the assumed flight trajectory and collected test data, the emission for both propulsions variants was determined. The values of emission parameters were compared and the results were presented in diagrams and discussed in the conclusions

scholarly journals The End of the M.E.?

2005 ◽  
Vol 127 (05) ◽  
pp. 26-29 ◽  
Author(s):  
Peter Huber ◽  
Mark P. Mills
Keyword(s):  
Fuel Cell ◽  
Mechanical Engineering ◽  
Combustion Engine ◽  
Electrical Power ◽  
Single Step ◽  
Second Century ◽  
Basic Operation ◽  
The Road ◽  
Energy Economy ◽  
On The Road

This article highlights that mechanical engineers control most of the rest of our energy economy. The engineering focus will shift inexorably toward finding the most efficient means of generating electricity on-board. Trains and monster trucks both use big diesel generators. Hybrid cars on the road today burn gasoline, but it is the fuel cell that attracts the most attention from visionaries and critics of the internal combustion engine. Remarkably elegant in its basic operation, the fuel cell transforms fuel into electricity in a single step, completely bypassing the furnace, turbine, and generator. In this scenario, mechanical engineering ultimately surrenders its last major under-the-hood citadel to chemical engineers. One might say that the age of mechanical engineering was launched by James Watt's steam engine in 1763, and propelled through its second century by Nikolaus Otto’s 1876 invention of the spark-ignited petroleum engine. We are now at the dawn of the age of electrical engineering, not because we recently learned how to generate light-speed electrical power, but because we have now finally learned how to control it.

scholarly journals Automotive Mechanical Vehicle Starter

2021 ◽  
Vol 2107 (1) ◽  
pp. 012021
Author(s):  
M M M. A Kader ◽  
Z B Razali ◽  
W A Mustafa ◽  
S A Saidi ◽  
A A Nagoor Gunny ◽  
...  
Keyword(s):  
Software Development ◽  
Magnetic Force ◽  
Combustion Engine ◽  
Electrical Power ◽  
Electrical Current ◽  
Mechanical Parts ◽  
Hardware Development ◽  
Start Up ◽  
Human Energy ◽  
Electrical Connections

Abstract This research is used to crank start automotive vehicle. There are many different system used in order to start-up vehicles using electric starter, in the time of battery low-power or totally drained. The purpose of this research is to help the driver to get out of this difficulty. Nowadays there are many people that have experienced such a bad moment, where they are stranded at road side due to malfunction starter in their car because of battery problem. Most of the vehicle electric starter failure is because of battery corrosion or battery undercharged. The importance of this research is to solve this problem. Starter is a vital part of the vehicle, without it no automotive vehicles able to operate. These starters will rotate an internal-combustion engine to initiate the engine’s operation under its own power. Starters also can be malfunction too due to corroded electrical connections or an undercharged battery. This system can be used to solve this problem. This system used human energy by using mechanical parts in order to produce electrical power. In order to produce electrical current, workforce will be applied by rotating the wheel that already linked by belt and from that rotations will trigger a magnetic force and it will produce an electrical current and supply it into battery. This system is divided into two development; hardware development and software development. The hardware development involved, mechanical device which is used and electrical device such as monitor. For software development, Fritzing is used to construct circuit.

Sign in / Sign up

Export Citation Format

Share Document