scholarly journals High PSRR Wide Supply Range Dual-Voltage Reference Circuit for Bio-Implantable Applications

Electronics ◽  
2021 ◽  
Vol 10 (16) ◽  
pp. 2024
Author(s):  
Ruhaifi Bin Abdullah Zawawi ◽  
Hojong Choi ◽  
Jungsuk Kim
Keyword(s):  
Capacitor Bank ◽  
Complementary Metal Oxide Semiconductor ◽  
Metal Oxide Semiconductor ◽  
Oxide Semiconductor ◽  
Cmos Process ◽  
Voltage Reference ◽  
Current Compensation ◽  
Fully Integrated ◽  
Reference Circuit ◽  
On Chip

On-chip systems are challenging owing to the limited size of the components, such as the capacitor bank in the rectifier. With a small on-chip capacitor, the output voltage of the rectifier might ring if the circuit experiences significant changes in current. The reference circuit is the first block after the rectifier, and the entire system relies on its robustness. A fully integrated dual-voltage reference circuit for bio-implantable applications is presented. The proposed circuit utilizes nonlinear current compensation techniques that significantly decrease supply variations and reject high-supply ripples for various frequencies. The reference circuit was verified using a 0.35 µm complementary metal-oxide semiconductor (CMOS) process. Maximum PSRR values of −112 dB and −128 dB were obtained. With a supply range from 2.8 to 12 V, the proposed design achieves 0.916 and 1.5 mV/V line regulation for the positive and negative reference circuits, respectively.

scholarly journals Universal Filter Based on Compact CMOS Structure of VDDDA

Sensors ◽  
2021 ◽  
Vol 21 (5) ◽  
pp. 1683
Author(s):  
Winai Jaikla ◽  
Fabian Khateb ◽  
Tomasz Kulej ◽  
Koson Pitaksuttayaprot
Keyword(s):  
Metal Oxide ◽  
Dynamic Range ◽  
Complementary Metal Oxide Semiconductor ◽  
Metal Oxide Semiconductor ◽  
Experimental Results ◽  
Oxide Semiconductor ◽  
Cmos Process ◽  
Voltage Gain ◽  
Universal Filter ◽  
Mos Transistor

This paper proposes the simulated and experimental results of a universal filter using the voltage differencing differential difference amplifier (VDDDA). Unlike the previous complementary metal oxide semiconductor (CMOS) structures of VDDDA that is present in the literature, the present one is compact and simple, owing to the employment of the multiple-input metal oxide semiconductor (MOS) transistor technique. The presented filter employs two VDDDAs, one resistor and two grounded capacitors, and it offers low-pass: LP, band-pass: BP, band-reject: BR, high-pass: HP and all-pass: AP responses with a unity passband voltage gain. The proposed universal voltage mode filter has high input impedances and low output impedance. The natural frequency and bandwidth are orthogonally controlled by using separated transconductance without affecting the passband voltage gain. For a BP filter, the root mean square (RMS) of the equivalent output noise is 46 µV, and the third intermodulation distortion (IMD3) is −49.5 dB for an input signal with a peak-to peak of 600 mV, which results in a dynamic range (DR) of 73.2 dB. The filter was designed and simulated in the Cadence environment using a 0.18-µm CMOS process from Taiwan semiconductor manufacturing company (TSMC). In addition, the experimental results were obtained by using the available commercial components LM13700 and AD830. The simulation results are in agreement with the experimental one that confirmed the advantages of the filter.

Millimeter-wave dual-mode and dual-band switchable Gilbert up-conversion mixer in 65-nm CMOS process

2021 ◽  
pp. 1-5
Author(s):  
Fang Zhu ◽  
Guo Qing Luo
Keyword(s):  
Millimeter Wave ◽  
Complementary Metal Oxide Semiconductor ◽  
Local Oscillator ◽  
Metal Oxide Semiconductor ◽  
Oxide Semiconductor ◽  
Dual Band ◽  
Cmos Process ◽  
Pumping Power ◽  
Dual Mode ◽  
Dc Power

Abstract In this paper, a millimeter-wave (MMW) dual-mode and dual-band switchable Gilbert up-conversion mixer in a commercial 65-nm complementary metal oxide semiconductor (CMOS) process is presented. By simply changing the bias, the proposed CMOS Gilbert up-conversion mixer can be switched between subharmonic and fundamental operation modes for MMW dual-band applications. With a low local oscillator pumping power of 3 dBm and low dc power consumption of 6 mW, the proposed CMOS Gilbert up-conversion mixer exhibits a measured conversion gain of −0.5 ± 1.5 dB from 37 to 50 GHz and 2.5 ± 1.5 dB from 17.5 to 32 GHz for the subharmonic and fundamental modes, respectively.

scholarly journals A Regulated Temperature-Insensitive High-Voltage Charge Pump in Standard CMOS Process for Micromachined Gyroscopes

Sensors ◽  
2019 ◽  
Vol 19 (19) ◽  
pp. 4149
Author(s):  
Xiang Li ◽  
Rui Li ◽  
Chunge Ju ◽  
Bo Hou ◽  
Qi Wei ◽  
...  
Keyword(s):  
Metal Oxide ◽  
High Voltage ◽  
Output Voltage ◽  
Charge Pump ◽  
Complementary Metal Oxide Semiconductor ◽  
Metal Oxide Semiconductor ◽  
Oxide Semiconductor ◽  
Cmos Process ◽  
Temperature Changes ◽  
Adjustable Range

Micromachined gyroscopes require high voltage (HV) for actuation and detection to improve its precision, but the deviation of the HV caused by temperature fluctuations will degrade the sensor’s performance. In this paper, a high-voltage temperature-insensitive charge pump is proposed. Without adopting BCD (bipolar-CMOS-DMOS) technology, the output voltage can be boosted over the breakdown voltage of n-well/substrate diode using triple-well NMOS (n-type metal-oxide-semiconductor) transistors. By controlling the pumping clock’s amplitude continuously, closed-loop regulation is realized to reduce the output voltage’s sensitivity to temperature changes. Besides, the output level is programmable linearly in a large range by changing the reference voltage. The whole circuit has been fabricated in a 0.18- μ m standard CMOS (complementary metal-oxide-semiconductor) process with a total area of 2.53 mm 2 . Measurements indicate that its output voltage has a linear adjustable range from around 13 V to 16.95 V, and temperature tests show that the maximum variations of the output voltage at − 40 ∼ 80 ∘ C are less than 1.1%.

scholarly journals Magnetic Micro Sensors with Two Magnetic Field Effect Transistors Fabricated Using the Commercial Complementary Metal Oxide Semiconductor Process

Sensors ◽  
2020 ◽  
Vol 20 (17) ◽  
pp. 4731
Author(s):  
Wei-Ren Chen ◽  
Yao-Chuan Tsai ◽  
Po-Jen Shih ◽  
Cheng-Chih Hsu ◽  
Ching-Liang Dai
Keyword(s):  
Magnetic Field ◽  
Metal Oxide ◽  
Field Effect ◽  
Field Effect Transistors ◽  
Magnetic Field Effect ◽  
Complementary Metal Oxide Semiconductor ◽  
Metal Oxide Semiconductor ◽  
Oxide Semiconductor ◽  
Cmos Process ◽  
Micro Sensor

The fabrication and characterization of a magnetic micro sensor (MMS) with two magnetic field effect transistors (MAGFETs) based on the commercial complementary metal oxide semiconductor (CMOS) process are investigated. The magnetic micro sensor is a three-axis sensing type. The structure of the magnetic microsensor is composed of an x/y-MAGFET and a z-MAGFET. The x/y-MAGFET is employed to sense the magnetic field (MF) in the x- and y-axis, and the z-MAGFET is used to detect the MF in the z-axis. To increase the sensitivity of the magnetic microsensor, gates are introduced into the two MAGFETs. The sensing current of the MAGFET enhances when a bias voltage is applied to the gates. The finite element method software Sentaurus TCAD was used to analyze the MMS’s performance. Experiments show that the MMS has a sensitivity of 182 mV/T in the x-axis MF and a sensitivity of 180 mV/T in the y-axis MF. The sensitivity of the MMS is 27.8 mV/T in the z-axis MF.

scholarly journals Fully integrated CMOS-compatible polarization analyzer

Nanophotonics ◽  
2019 ◽  
Vol 8 (3) ◽  
pp. 467-474 ◽  
Author(s):  
Wenhao Wu ◽  
Yu Yu ◽  
Wei Liu ◽  
Xinliang Zhang
Keyword(s):  
Polarization State ◽  
Complementary Metal Oxide Semiconductor ◽  
Polarization Measurement ◽  
Oxide Semiconductor ◽  
Polarization Angle ◽  
Fully Integrated ◽  
Polarization Analyzer ◽  
On Chip ◽  
Easy Integration ◽  
Silicon Based

AbstractPolarization measurement has been widely used in material characterization, medical diagnosis and remote sensing. However, existing commercial polarization analyzers are either bulky schemes or operate in non-real time. Recently, various polarization analyzers have been reported using metal metasurface structures, which require elaborate fabrication and additional detection devices. In this paper, a compact and fully integrated silicon polarization analyzer with a photonic crystal-like metastructure for polarization manipulation and four subsequent on-chip photodetectors for light-current conversion is proposed and demonstrated. The input polarization state can be retrieved instantly by calculating four output photocurrents. The proposed polarization analyzer is complementary metal oxide semiconductor-compatible, making it possible for mass production and easy integration with other silicon-based devices monolithically. Experimental verification is also performed for comparison with a commercial polarization analyzer, and deviations of the measured polarization angle are <±1.2%.

Sign in / Sign up

Export Citation Format

Share Document