scholarly journals Design and Optimization of Multiple Circumferential Casing Grooves Distribution Considering Sweep and Lean Variations on the Blade Tip

Energies ◽  
2018 ◽  
Vol 11 (9) ◽  
pp. 2401
Author(s):  
Weimin Song ◽  
Yufei Zhang ◽  
Haixin Chen
Keyword(s):  
Pressure Ratio ◽  
Three Dimensional ◽  
Axial Distribution ◽  
Stall Margin ◽  
Design Point ◽  
Casing Treatment ◽  
Design And Optimization ◽  
Practical Engineering ◽  
Engineering Strategy ◽  
Blade Tip

This paper focuses on the design and optimization of the axial distribution of the circumferential groove casing treatment (CGCT). Effects of the axial location of multiple casing grooves on the flow structures are numerically studied. Sweep and lean variations are then introduced to the blade tip, and their influences on the grooves are discussed. The results show that the ability of the CGCT to relieve the blockage varies with the distribution of grooves, and the three-dimensional blading affects the performance of both the blade and the CGCT. Accordingly, a multi-objective optimization combining the CGCT design with the sweep and lean design is conducted. Objectives, including the total pressure ratio and the adiabatic efficiency, are set at the design point; meanwhile, the choking mass flow and the near-stall performance are constrained. The coupling between the CGCT and the blade is improved, which contributes to an optimal design point performance and a sufficient stall margin. The sweep and lean in the tip redistribute the spanwise and chordwise loading, which enhances the ability of the CGCT to improve the blade’s performance. This work shows that the present CGCT-blade integrated optimization is a practical engineering strategy to develop the working capacity and efficiency of a compressor blade while achieving the stall margin extension.

Investigation of Recirculating Casing Treatment for Low-Pressure Ratio Mixed-Flow Micro-Compressor

2020 ◽  
Author(s):  
Kewei Xu ◽  
Gecheng Zha
Keyword(s):  
Pressure Ratio ◽  
Numerical Approach ◽  
Efficiency Loss ◽  
Stall Margin ◽  
Design Point ◽  
Casing Treatment ◽  
Final Design ◽  
Upstream Flow ◽  
Total Pressure Ratio ◽  
Good Agreement

Abstract This paper investigates the recirculating casing treatment (RCT) of a low total pressure ratio micro-compressor to achieve stall margin enhancement while minimizing the design point efficiency penalty. Three RCT injection and extraction configurations are studied, including combined slot-duct, ducts only, and slot only. The numerical approach is validated with a tested micro-compressor using RCT. A very good agreement is achieved between the predicted speedlines and the measured results. To minimize the design point efficiency loss, it is observed that the optimal location of extraction and injection is where the recirculated flow rate can be minimized at the design point. To maximize stall margin, extraction location should favor minimizing the tip blockage such as at the location where the tip flow separation of the baseline blade is fully developed. In addition, the slot configuration that generates pre-swirl to the upstream flow is beneficial to improve stall margin due to reduced incidence. The highest stall margin enhancement achieved is 9.49% with the slot geometry that has the extraction at the 62%C chordwise location, but has a design point efficiency loss of 1.9%. Overall, a small efficiency penalty of 0.6% at the design point is achieved for the final design with the stall margin increased by 6.2%.

Numerical Investigation on the Effect of Bleed Port With Self-Recirculating Casing Treatment on the Stability of a 1.5-Stage Transonic Compressor

2019 ◽  
Author(s):  
Yiming Zhong ◽  
WuLi Chu ◽  
HaoGuang Zhang
Keyword(s):  
Pressure Ratio ◽  
Three Dimensional ◽  
Axial Compressor ◽  
Stability Margin ◽  
Axial Position ◽  
Stable Operation ◽  
Stall Margin ◽  
Casing Treatment ◽  
Transonic Compressor ◽  
Compressor Efficiency

Abstract Compared to the traditional casing treatment, the self-recirculating casing treatment (SCT) can improve or not decrease the compressor efficiency while achieving the stall margin improvement. For the bleed port, the main design indicator is to reduce the flow loss caused by suction, while providing sufficient jet flow and jet pressure to the injector. In order to gain a better study of the bleed port stabilization mechanisms, the bleed configuration was parameterized with the bleed port inlet width and the bleed port axial position. Five kinds of recirculating casing treatments were applied to a 1.5-stage transonic axial compressor with the method of three-dimensional unsteady numerical simulation. Fifteen identical self-recirculating devices are uniformly mounted around the annulus. The numerical results show that the SCT can improve compressor total pressure ratio and stability, shift the stall margin towards lower mass flows. Furthermore, it has no impact on compressor efficiency. The optimal case presents that stability margin is improved by 6.7% employing 3.1% of the annulus mass flow. Expanding bleed port inlet width to an intermediate level can further enhance compressor stability, but excessive bleed port inlet width will reduce the stabilization effect. The optimal bleed port position is located in the blocked area of the low energy group at the top of the rotor. In the case of solid casing, stall inception was the tip blockage, which was mainly triggered by the interaction of the tip leakage vortex and passage shock. From radial distribution, the casing treatment predominantly affects the above 70% span. The reduction of tip reflux region by suction effect is the main reason for the extension of stable operation range. The SCT also has an obvious stability improvement in tip blockage stall, while delaying the occurrence of compressor stall.

scholarly journals Stability Enhancement of a Single-Stage Transonic Axial Compressor Using Inclined Oblique Slots

Energies ◽  
2021 ◽  
Vol 14 (9) ◽  
pp. 2346
Author(s):  
Tien-Dung Vuong ◽  
Kwang-Yong Kim
Keyword(s):  
Pressure Ratio ◽  
Three Dimensional ◽  
Axial Compressor ◽  
Single Stage ◽  
Rotor Blades ◽  
Navier Stokes ◽  
Optimized Design ◽  
Stall Margin ◽  
Casing Treatment ◽  
Transonic Axial Compressor

A casing treatment using inclined oblique slots (INOS) is proposed to improve the stability of the single-stage transonic axial compressor, NASA Stage 37, during operation. The slots are installed on the casing of the rotor blades. The aerodynamic performance was estimated using three-dimensional steady Reynolds-Averaged Navier-Stokes analysis. The results showed that the slots effectively increased the stall margin of the compressor with slight reductions in the pressure ratio and adiabatic efficiency. Three geometric parameters were tested in a parametric study. A single-objective optimization to maximize the stall margin was carried out using a Genetic Algorithm coupled with a surrogate model created by a radial basis neural network. The optimized design increased the stall margin by 37.1% compared to that of the smooth casing with little impacts on the efficiency and pressure ratio.

scholarly journals Aerodynamic Optimization Design of a Supersonic Compressor Rotor with High Pressure Ratio

2021 ◽  
Vol 2021 ◽  
pp. 1-24
Author(s):  
Cui Cui ◽  
Zhenggui Zhou ◽  
Endor Liu
Keyword(s):  
Shock Waves ◽  
Total Pressure ◽  
Optimization Design ◽  
Pressure Ratio ◽  
Strong Shock ◽  
Stall Margin ◽  
Design Point ◽  
Compressor Rotor ◽  
Blade Tip ◽  
Total Pressure Ratio

Supersonic compressors have a high wheel speed and operational capability, which facilitate a high stage pressure ratio. However, the strong shock waves in the passage of a supersonic rotor and the interference between shock waves and boundary layers can lead to large flow loss and low efficiency. Moreover, the existing design of a high-load supersonic compressor has the problem of small stall margin. In this study, an automatic optimization method including 2D profile optimization and 3D blade optimization is proposed to achieve a high efficiency at the design point of a supersonic compressor rotor under the premise of reaching the desired mass flow rate and total pressure ratio. According to the analysis of flow near the stall point of the supersonic compressor rotor, the mechanism responsible for rotor tip stall is established, that is, the aerodynamic throat appeared inside the flow passage, reducing the ability of the blade tip to withstand back pressure, and the low-speed areas caused by the tip-leakage-vortex breakage and boundary layer separation reduced the flow capacity of the blade tip. Based on the reasons for rotor stall, three methods are proposed to improve the stall margin, which include increasing the exit radius of the upper meridian, forward sweep of the blade tip, and increasing the chord length of the blade tip. The above method is used to design a supersonic rotor with a total pressure ratio of 2.8, which exhibits an efficiency of 0.902 at the design point and a stall margin of 18.11%.

Performance enhancement in transonic axial compressors using blade tip injection coupled with casing treatment

2005 ◽  
Vol 219 (5) ◽  
pp. 321-331 ◽  
Author(s):  
B. H. Beheshti ◽  
B Farhanieh ◽  
K Ghorbanian ◽  
J. A. Teixeira ◽  
P. C. Ivey
Keyword(s):  
Flow Injection ◽  
High Speed ◽  
Performance Enhancement ◽  
Three Dimensional ◽  
Stall Margin ◽  
Casing Treatment ◽  
Transonic Compressor ◽  
Compressor Rotor ◽  
Blade Tip ◽  
Tip Injection

The casing treatment and flow injection upstream of the rotor tip are two effective approaches in suppressing instabilities or recovering from a fully developed stall. This paper presents numerical simulations for a high-speed transonic compressor rotor, NASA Rotor 37, applying a state-of-the-art design for the blade tip injection. This is characterized by introducing a jet flow directly into the casing treatment machined into the shroud. The casing treatment is positioned over the blade tip region and exceeds the impeller axially by ∼30 per cent of the tip chord both in the upstream and in the downstream directions. To numerically solve the governing equations, the three-dimensional finite element based finite volume method CFD solver CFX-TASCflow (version 2.12.1) is employed. For a compressible flow with varying density, Reynolds-averaging leads to appearance of complicated correlations. To avoid this, the mass-weighted or Favre-averaging is applied. Using an injected mass flow of 2.4 per cent of the annulus flow, the present design can improve stall margin by up to 7 per cent when compared with a smooth casing compressor without tip injection. This research can lead to an optimum design of recirculating casing treatments or other mechanisms for performance enhancement applying tip flow injection.

scholarly journals Axial Flow Compressor Stability Enhancement: Circumferential T-Shape Grooves Performance Investigation

Aerospace ◽  
2021 ◽  
Vol 8 (1) ◽  
pp. 12
Author(s):  
Marco Porro ◽  
Richard Jefferson-Loveday ◽  
Ernesto Benini
Keyword(s):  
Vortex Breakdown ◽  
Pressure Ratio ◽  
Axial Flow ◽  
Suction Side ◽  
Treatment Technique ◽  
Tip Leakage Flow ◽  
Stall Inception ◽  
Stall Margin ◽  
Casing Treatment ◽  
Stall Margin Improvement

This work focuses its attention on possibilities to enhance the stability of an axial compressor using a casing treatment technique. Circumferential grooves machined into the case are considered and their performances evaluated using three-dimensional steady state computational simulations. The effects of rectangular and new T-shape grooves on NASA Rotor 37 performances are investigated, resolving in detail the flow field near the blade tip in order to understand the stall inception delay mechanism produced by the casing treatment. First, a validation of the computational model was carried out analysing a smooth wall case without grooves. The comparisons of the total pressure ratio, total temperature ratio and adiabatic efficiency profiles with experimental data highlighted the accuracy and validity of the model. Then, the results for a rectangular groove chosen as the baseline case demonstrated that the groove interacts with the tip leakage flow, weakening the vortex breakdown and reducing the separation at the blade suction side. These effects delay stall inception, improving compressor stability. New T-shape grooves were designed keeping the volume as a constant parameter and their performances were evaluated in terms of stall margin improvement and efficiency variation. All the configurations showed a common efficiency loss near the peak condition and some of them revealed a stall margin improvement with respect to the baseline. Due to their reduced depth, these new configurations are interesting because they enable the use of a thinner light-weight compressor case as is desirable in aerospace applications.

Automatic Three-Dimensional Optimisation of a Modern Tandem Compressor Vane

2014 ◽  
Author(s):  
R. C. Schlaps ◽  
S. Shahpar ◽  
V. Gümmer
Keyword(s):  
Pressure Ratio ◽  
Three Dimensional ◽  
Trust Region ◽  
Automatic Generation ◽  
Navier Stokes ◽  
Design Parameters ◽  
High Fidelity ◽  
Stall Margin ◽  
Design Choice ◽  
Multipoint Approximation

In order to increase the performance of a modern gas turbine, compressors are required to provide higher pressure ratio and avoid incurring higher losses. The tandem aerofoil has the potential to achieve a higher blade loading in combination with lower losses compared to single vanes. The main reason for this is due to the fact that a new boundary layer is generated on the second blade surface and the turning can be achieved with smaller separation occurring. The lift split between the two vanes with respect to the overall turning is an important design choice. In this paper an automated three-dimensional optimisation of a highly loaded compressor stator is presented. For optimisation a novel methodology based on the Multipoint Approximation Method (MAM) is used. MAM makes use of an automatic design of experiments, response surface modelling and a trust region to represent the design space. The CFD solutions are obtained with the high-fidelity 3D Navier-Stokes solver HYDRA. In order to increase the stage performance the 3D shape of the tandem vane is modified changing both the front and rear aerofoils. Moreover the relative location of the two aerofoils is controlled modifying the axial and tangential relative positions. It is shown that the novel optimisation methodology is able to cope with a large number of design parameters and produce designs which performs better than its single vane counterpart in terms of efficiency and numerical stall margin. One of the key challenges in producing an automatic optimisation process has been the automatic generation of high-fidelity computational meshes. The multi block-structured, high-fidelity meshing tool PADRAM is enhanced to cope with the tandem blade topologies. The wakes of each aerofoil is properly resolved and the interaction and the mixing of the front aerofoil wake and the second tandem vane are adequately resolved.

Numerical Investigation on the Effects of Circumferential Coverage of Injection in a Transonic Compressor With Discrete Tip Injection

2014 ◽  
Author(s):  
Wei Wang ◽  
Wuli Chu ◽  
Haoguang Zhang ◽  
Yanhui Wu
Keyword(s):  
Total Pressure ◽  
Pressure Ratio ◽  
Time Lag ◽  
Three Dimensional ◽  
Stability Margin ◽  
Transonic Compressor ◽  
Blade Tip ◽  
Tip Injection ◽  
The Stability ◽  
Total Pressure Ratio

Discrete tip injection upstream of the rotor tip is an effective technique to extend stability margin for a compressor system in an aeroengine. The current study investigates the effects of injectors’ circumferential coverage on compressor performance and stability using time-accurate three-dimensional numerical simulations for multi passages in a transonic compressor. The percentage of circumferential coverage for all the six injectors ranges from 6% to 87% for the five investigated configurations. Results indicate that circumferential coverage of tip injection can greatly affect compressor stability and total pressure ratio, but has little influence on adiabatic efficiency. The improvement of compressor total pressure ratio is linearly related with the increasing circumferential coverage. The unsteady flow fields show that there exists a non-ignorable time lag of the injection effects between the passage inlet and outlet, and blade tip loading will not decline until the injected flow reaches the passage outlet. Stability improves sharply with the increasing circumferential coverage when the coverage is less than 27%, but increases flatly for the rest. It is proven that the injection efficiency which is a measurement of averaged blockage decrement in the injected region is an effective guideline to predict the stability improvement.

scholarly journals Recessed Casing Treatment Effects on Fan Performance and Flow Field

1995 ◽  
Author(s):  
C. S. Kang ◽  
A. B. McKenzie ◽  
R. L. Elder
Keyword(s):  
Flow Field ◽  
Axial Flow ◽  
Pressure Rise ◽  
Operating Efficiency ◽  
Flow Measurements ◽  
Blade Loading ◽  
Stall Margin ◽  
Casing Treatment ◽  
Stall Margin Improvement ◽  
Blade Tip

An experimental investigation to examine the influence of the vaned recess casing treatment on stall margin, operating efficiency and the flow field of a low speed axial flow fan with aerospace type blade loading is presented. Different geometrical designs of the vaned passages were examined. The best configuration resulted in a stall margin improvement of 67%, a significantly higher pressure rise in the stall region and insignificant change in peak efficiency. Detailed 3-D flow measurements in the endwall region and in the casing recess were carried out with a slanted hot-wire, providing some insight to the operation of the device. The results revealed that the stall margin improvement was largely due to the removal of flow from the blade tip to the recess, and the elimination of the growth of the stall region at the tip, which occurs at stall in the solid casing build.

Design Optimization of Circumferential Casing Grooves for a Transonic Axial Compressor to Enhance Stall Margin

2010 ◽  
Author(s):  
Kwang-Jin Choi ◽  
Jin-Hyuk Kim ◽  
Kwang-Yong Kim
Keyword(s):  
Design Optimization ◽  
Numerical Solutions ◽  
Stokes Equations ◽  
Pressure Ratio ◽  
Three Dimensional ◽  
Axial Compressor ◽  
Latin Hypercube Sampling ◽  
Optimum Shape ◽  
Data Set ◽  
Stall Margin

This paper presents a design optimization of an axial compressor with NASA Rotor 37 and five circumferential casing grooves for enhancement of stall margin. Three-dimensional Reynolds-averaged Navier-Stokes equations with the shear stress transport turbulence model are discretized by finite volume approximations and solved on hexahedral grids for the flow analyses. The validation of the numerical results is performed in comparison with experimental data for pressure ratio and adiabatic efficiency. The Latin-hypercube sampling as design-of-experiments is used to generate the twelve design points within the design space. A stall margin parameter is considered as an objective function with two design variables defining the geometry of the circumferential casing grooves. The radial basis neural network method employed as a surrogate model for the design optimization of the circumferential casing grooves is trained on the numerical solutions by carrying out leave-one-out cross-validation for the data set. The results show that the stall margin of the optimum shape is enhanced considerably by the design optimization compared to the cases with smooth casing and the reference grooves.

Sign in / Sign up

Export Citation Format

Share Document