scholarly journals Stability Enhancement of a Single-Stage Transonic Axial Compressor Using Inclined Oblique Slots

Energies ◽  
2021 ◽  
Vol 14 (9) ◽  
pp. 2346
Author(s):  
Tien-Dung Vuong ◽  
Kwang-Yong Kim
Keyword(s):  
Pressure Ratio ◽  
Three Dimensional ◽  
Axial Compressor ◽  
Single Stage ◽  
Rotor Blades ◽  
Navier Stokes ◽  
Optimized Design ◽  
Stall Margin ◽  
Casing Treatment ◽  
Transonic Axial Compressor

A casing treatment using inclined oblique slots (INOS) is proposed to improve the stability of the single-stage transonic axial compressor, NASA Stage 37, during operation. The slots are installed on the casing of the rotor blades. The aerodynamic performance was estimated using three-dimensional steady Reynolds-Averaged Navier-Stokes analysis. The results showed that the slots effectively increased the stall margin of the compressor with slight reductions in the pressure ratio and adiabatic efficiency. Three geometric parameters were tested in a parametric study. A single-objective optimization to maximize the stall margin was carried out using a Genetic Algorithm coupled with a surrogate model created by a radial basis neural network. The optimized design increased the stall margin by 37.1% compared to that of the smooth casing with little impacts on the efficiency and pressure ratio.

Parametric Study on Aerodynamic Performance of a Transonic Axial Compressor with a Casing Groove and Tip Injection

2013 ◽  
Vol 284-287 ◽  
pp. 872-877 ◽  
Author(s):  
Dae Woong Kim ◽  
Jin Hyuk Kim ◽  
Kwang Yong Kim
Keyword(s):  
Parametric Study ◽  
Stokes Equations ◽  
Pressure Ratio ◽  
Three Dimensional ◽  
Axial Compressor ◽  
Aerodynamic Performance ◽  
Navier Stokes ◽  
Stall Margin ◽  
Transonic Axial Compressor ◽  
Tip Injection

This paper presents a parametric study on aerodynamic performance of a transonic axial compressor combined with a casing groove and tip injection using three-dimensional Reynolds-average Navier-Stokes equations. The front and rear lengths and height of the groove are selected as the geometric parameters to investigate their effects on the stall margin and peak adiabatic efficiency. These parameters are changed with constant injection. The validation of the numerical results is performed in comparison with experimental data for the total pressure ratio and adiabatic efficiency. As the results of the parametric study, the maximum stall margin and peak adiabatic efficiency are obtained in the axial compressor having 70% groove height of the reference groove. The stall margin and peak adiabatic efficiency in other cases are also improved in comparison with the axial compressors with the smooth casing and reference groove. The results show that both the stall margin and the peak adiabatic efficiency are considerably improved by the application of the casing groove combined with tip injection in an axial compressor.

Numerical Investigation on the Effect of Bleed Port With Self-Recirculating Casing Treatment on the Stability of a 1.5-Stage Transonic Compressor

2019 ◽  
Author(s):  
Yiming Zhong ◽  
WuLi Chu ◽  
HaoGuang Zhang
Keyword(s):  
Pressure Ratio ◽  
Three Dimensional ◽  
Axial Compressor ◽  
Stability Margin ◽  
Axial Position ◽  
Stable Operation ◽  
Stall Margin ◽  
Casing Treatment ◽  
Transonic Compressor ◽  
Compressor Efficiency

Abstract Compared to the traditional casing treatment, the self-recirculating casing treatment (SCT) can improve or not decrease the compressor efficiency while achieving the stall margin improvement. For the bleed port, the main design indicator is to reduce the flow loss caused by suction, while providing sufficient jet flow and jet pressure to the injector. In order to gain a better study of the bleed port stabilization mechanisms, the bleed configuration was parameterized with the bleed port inlet width and the bleed port axial position. Five kinds of recirculating casing treatments were applied to a 1.5-stage transonic axial compressor with the method of three-dimensional unsteady numerical simulation. Fifteen identical self-recirculating devices are uniformly mounted around the annulus. The numerical results show that the SCT can improve compressor total pressure ratio and stability, shift the stall margin towards lower mass flows. Furthermore, it has no impact on compressor efficiency. The optimal case presents that stability margin is improved by 6.7% employing 3.1% of the annulus mass flow. Expanding bleed port inlet width to an intermediate level can further enhance compressor stability, but excessive bleed port inlet width will reduce the stabilization effect. The optimal bleed port position is located in the blocked area of the low energy group at the top of the rotor. In the case of solid casing, stall inception was the tip blockage, which was mainly triggered by the interaction of the tip leakage vortex and passage shock. From radial distribution, the casing treatment predominantly affects the above 70% span. The reduction of tip reflux region by suction effect is the main reason for the extension of stable operation range. The SCT also has an obvious stability improvement in tip blockage stall, while delaying the occurrence of compressor stall.

AERODYNAMIC PERFORMANCE OF AN AXIAL COMPRESSOR WITH A CASING GROOVE COMBINED WITH INJECTION

2013 ◽  
Vol 37 (3) ◽  
pp. 283-292 ◽  
Author(s):  
Dae-Woong Kim ◽  
Jin-Hyuk Kim ◽  
Kwang-Yong Kim
Keyword(s):  
Turbulence Model ◽  
Parametric Study ◽  
Stokes Equations ◽  
Three Dimensional ◽  
Axial Compressor ◽  
Aerodynamic Performance ◽  
Navier Stokes ◽  
Navier Stokes Equations ◽  
Stall Margin ◽  
Transonic Axial Compressor

Aerodynamic performance of a transonic axial compressor with a casing groove combined with injection has been investigated in this work. Three-dimensional Reynolds-averaged Navier–Stokes equations with k-ε turbulence model are discretized by finite volume approximations and solved on hexahedral grids for the flow analyses. For parametric study, the front and rear lengths and height of the casing groove are selected as the geometric parameters and are changed with constant injection to investigate their effects on the stall margin and peak adiabatic efficiency. As a result of the parametric study, the maximum stall margin and peak adiabatic efficiency are found to be obtained in the axial compressor having 70% height of the reference groove. The results show that the application of the casing groove combined with injection to an axial compressor is effective for the simultaneous improvement of both the stall margin and peak adiabatic efficiency of the compressor.

scholarly journals Design Optimization of a Dual-Bleeding Recirculation Channel to Enhance Operating Stability of a Transonic Axial Compressor

Energies ◽  
2021 ◽  
Vol 15 (1) ◽  
pp. 159
Author(s):  
Tien-Dung Vuong ◽  
Kwang-Yong Kim
Keyword(s):  
Design Optimization ◽  
Pressure Ratio ◽  
Three Dimensional ◽  
Axial Compressor ◽  
Aerodynamic Performance ◽  
Maximum Pressure ◽  
Stall Margin ◽  
Design Variables ◽  
Operating Stability ◽  
Transonic Axial Compressor

The present work performed a comprehensive investigation to find the effects of a dual-bleeding port recirculation channel on the aerodynamic performance of a single-stage transonic axial compressor, NASA Stage 37, and optimized the channel’s configuration to enhance the operating stability of the compressor. The compressor’s performance was examined using three parameters: The stall margin, adiabatic efficiency, and pressure ratio. Steady-state three-dimensional Reynolds-averaged Navier–Stokes analyses were performed to find the flow field and aerodynamic performance. The results showed that the addition of a bleeding channel increased the recirculation channel’s stabilizing effect compared to the single-bleeding channel. Three design variables were selected for optimization through a parametric study, which was carried out to examine the influences of six geometric parameters on the channel’s effectiveness. Surrogate-based design optimization was performed using the particle swarm optimization algorithm coupled with a surrogate model based on the radial basis neural network. The optimal design was found to increase the stall margin by 51.36% compared to the case without the recirculation channel with only 0.55% and 0.28% reductions in the peak adiabatic efficiency and maximum pressure ratio, respectively.

Effects of a Circumferential Feed-Back Channel on Aerodynamic Performance of a Single-Stage Transonic Axial Compressor

2017 ◽  
Author(s):  
Cong-Truong Dinh ◽  
Sang-Bum Ma ◽  
Kwang-Yong Kim
Keyword(s):  
Stokes Equations ◽  
Three Dimensional ◽  
Axial Compressor ◽  
Aerodynamic Performance ◽  
Numerical Results ◽  
Single Stage ◽  
Navier Stokes ◽  
Channel Inlet ◽  
Navier Stokes Equations ◽  
Stall Margin

This paper presents an investigation of a circumferential feed-back channel located on shroud surface in rotor domain to find its effects on aerodynamic performance of a single-stage axial compressor, NASA Stage 37, using three-dimensional Reynolds-averaged Navier-Stokes equations. Validation of numerical results was performed using experimental data for both of single rotor and single-stage compressors. A parametric study of the feed-back channel was performed using various geometric parameters related to the locations and shapes of the channel inlet and outlet. The numerical results showed that a reference circumferential feed-back channel increased the stall margin by 26.8% with 0.14% reduction in the peak adiabatic efficiency, compared to the case without the feed-back channel.

Effects of stator splitter blades on aerodynamic performance of a single-stage transonic axial compressor

2020 ◽  
Vol 14 (4) ◽  
pp. 7369-7378
Author(s):  
Ky-Quang Pham ◽  
Xuan-Truong Le ◽  
Cong-Truong Dinh
Keyword(s):  
Stokes Equations ◽  
Three Dimensional ◽  
Axial Compressor ◽  
Aerodynamic Performance ◽  
Numerical Results ◽  
Single Stage ◽  
Navier Stokes ◽  
Navier Stokes Equations ◽  
Operating Stability ◽  
Length Coverage

Splitter blades located between stator blades in a single-stage axial compressor were proposed and investigated in this work to find their effects on aerodynamic performance and operating stability. Aerodynamic performance of the compressor was evaluated using three-dimensional Reynolds-averaged Navier-Stokes equations using the k-e turbulence model with a scalable wall function. The numerical results for the typical performance parameters without stator splitter blades were validated in comparison with experimental data. The numerical results of a parametric study using four geometric parameters (chord length, coverage angle, height and position) of the stator splitter blades showed that the operational stability of the single-stage axial compressor enhances remarkably using the stator splitter blades. The splitters were effective in suppressing flow separation in the stator domain of the compressor at near-stall condition which affects considerably the aerodynamic performance of the compressor.

Automatic Three-Dimensional Optimisation of a Modern Tandem Compressor Vane

2014 ◽  
Author(s):  
R. C. Schlaps ◽  
S. Shahpar ◽  
V. Gümmer
Keyword(s):  
Pressure Ratio ◽  
Three Dimensional ◽  
Trust Region ◽  
Automatic Generation ◽  
Navier Stokes ◽  
Design Parameters ◽  
High Fidelity ◽  
Stall Margin ◽  
Design Choice ◽  
Multipoint Approximation

In order to increase the performance of a modern gas turbine, compressors are required to provide higher pressure ratio and avoid incurring higher losses. The tandem aerofoil has the potential to achieve a higher blade loading in combination with lower losses compared to single vanes. The main reason for this is due to the fact that a new boundary layer is generated on the second blade surface and the turning can be achieved with smaller separation occurring. The lift split between the two vanes with respect to the overall turning is an important design choice. In this paper an automated three-dimensional optimisation of a highly loaded compressor stator is presented. For optimisation a novel methodology based on the Multipoint Approximation Method (MAM) is used. MAM makes use of an automatic design of experiments, response surface modelling and a trust region to represent the design space. The CFD solutions are obtained with the high-fidelity 3D Navier-Stokes solver HYDRA. In order to increase the stage performance the 3D shape of the tandem vane is modified changing both the front and rear aerofoils. Moreover the relative location of the two aerofoils is controlled modifying the axial and tangential relative positions. It is shown that the novel optimisation methodology is able to cope with a large number of design parameters and produce designs which performs better than its single vane counterpart in terms of efficiency and numerical stall margin. One of the key challenges in producing an automatic optimisation process has been the automatic generation of high-fidelity computational meshes. The multi block-structured, high-fidelity meshing tool PADRAM is enhanced to cope with the tandem blade topologies. The wakes of each aerofoil is properly resolved and the interaction and the mixing of the front aerofoil wake and the second tandem vane are adequately resolved.

Stall Warning Using the Rotor Tip Pressure in a Transonic Axial Compressor With Circumferential Grooves

2018 ◽  
Author(s):  
Byeung Jun Lim ◽  
Tae Choon Park ◽  
Young Seok Kang
Keyword(s):  
Mass Flow Rate ◽  
Mass Flow ◽  
Flow Rate ◽  
Axial Compressor ◽  
Rotating Stall ◽  
Single Stage ◽  
Stall Inception ◽  
Casing Treatment ◽  
Stall Warning ◽  
Transonic Axial Compressor

In this study, characteristics of stall inception in a single-stage transonic axial compressor with circumferential grooves casing treatment were investigated experimentally. Additionally, the characteristic of increasing irregularity in the pressure inside circumferential grooves as the compressor approaches the stall limit was applied to the stall warning method. Spike-type rotating stall was observed in the single-stage transonic axial compressor with smooth casing. When circumferential grooves were applied, the stall inception was suppressed and the operating point of the compressor moved to lower flow rate than the stall limit. A spike-like disturbance was developed into a rotating stall cell and then the Helmholtz perturbation was overlapped on it at N = 80%. At N = 70 %, the Helmholtz perturbation was observed first and the amplitude of the wave gradually increased as mass flow rate decreased. At N = 60%, spike type stall inceptions were observed intermittently and then developed into continuous rotating stall at lower mass flow rate. Pressure measured at the bottom of circumferential grooves showed that the level of irregularity of pressure increased as flow rate decreased. Based on the characteristic of increasing irregularity of the pressure signals inside the circumferential grooves as stall approaches, an autocorrelation technique was applied to the stall warning. This technique could be used to provide warning against stall and estimate real-time stall margins in compressors with casing treatments.

Effects of Tip Clearance on Hot Streak Migration in a High-Subsonic Single-Stage Turbine

2000 ◽  
Author(s):  
Daniel J. Dorney ◽  
Douglas L. Sondak
Keyword(s):  
Experimental Data ◽  
Three Dimensional ◽  
Single Stage ◽  
Rotor Blades ◽  
Tip Clearance ◽  
Navier Stokes ◽  
Radial Spreading ◽  
Rotor Surface ◽  
Hot Streak ◽  
Turbine Airfoils

Experimental data have shown that combustor temperature non-uniformities can lead to the excessive heating of first-stage rotor blades in turbines. This heating of the rotor blades can lead to thermal fatigue and degrade turbine performance. The results of recent studies have shown that variations in the circumferential location, or clocking, of the first-stage vane airfoils can be used to minimize the adverse effects of the hot streaks due to the hot fluid mixing with the cooler fluid contained in the vane wake. In addition, the effects of the hot streak/airfoil count ratio on the heating patterns of turbine airfoils have been quantified. In the present investigation, three-dimensional unsteady Navier-Stokes simulations have been performed for a single-stage high-pressure turbine geometry operating in high subsonic flow to study the effects of tip clearance on hot streak migration. Baseline simulations were initially performed without hot streaks to compare with the experimental data. Two simulations were then performed with a superimposed combustor hot streak; in the first the tip clearance was set at the experimental value, while in the second the rotor was allowed to scrape along the outer case (i.e., the limit as the tip clearance goes to zero). The predicted results for the baseline simulations show good agreement with the available experimental data. The simulations with the hot streak indicate that the tip clearance increases the radial spreading of the hot fluid, and increases the integrated rotor surface temperature compared to the case without tip clearance.

scholarly journals Design and Optimization of Multiple Circumferential Casing Grooves Distribution Considering Sweep and Lean Variations on the Blade Tip

Energies ◽  
2018 ◽  
Vol 11 (9) ◽  
pp. 2401
Author(s):  
Weimin Song ◽  
Yufei Zhang ◽  
Haixin Chen
Keyword(s):  
Pressure Ratio ◽  
Three Dimensional ◽  
Axial Distribution ◽  
Stall Margin ◽  
Design Point ◽  
Casing Treatment ◽  
Design And Optimization ◽  
Practical Engineering ◽  
Engineering Strategy ◽  
Blade Tip

This paper focuses on the design and optimization of the axial distribution of the circumferential groove casing treatment (CGCT). Effects of the axial location of multiple casing grooves on the flow structures are numerically studied. Sweep and lean variations are then introduced to the blade tip, and their influences on the grooves are discussed. The results show that the ability of the CGCT to relieve the blockage varies with the distribution of grooves, and the three-dimensional blading affects the performance of both the blade and the CGCT. Accordingly, a multi-objective optimization combining the CGCT design with the sweep and lean design is conducted. Objectives, including the total pressure ratio and the adiabatic efficiency, are set at the design point; meanwhile, the choking mass flow and the near-stall performance are constrained. The coupling between the CGCT and the blade is improved, which contributes to an optimal design point performance and a sufficient stall margin. The sweep and lean in the tip redistribute the spanwise and chordwise loading, which enhances the ability of the CGCT to improve the blade’s performance. This work shows that the present CGCT-blade integrated optimization is a practical engineering strategy to develop the working capacity and efficiency of a compressor blade while achieving the stall margin extension.

Sign in / Sign up

Export Citation Format

Share Document