scholarly journals Investigation of Start-Up Characteristics of Thermosyphons Modified with Different Hydrophilic and Hydrophobic Inner Surfaces

Energies ◽  
2020 ◽  
Vol 13 (3) ◽  
pp. 765 ◽  
Author(s):  
Xiaolong Ma ◽  
Zhongchao Zhao ◽  
Pengpeng Jiang ◽  
Shan Yang ◽  
Shilin Li ◽  
...  
Keyword(s):  
Contact Angle ◽  
Significant Role ◽  
Smooth Surface ◽  
Hydrophobic Properties ◽  
Two Phase ◽  
Condenser Section ◽  
Chemical Coating ◽  
Evaporator Section ◽  
Wall Superheat ◽  
Start Up

In this paper, the influence of wettability properties on the start-up characteristics of two-phase closed thermosyphons (TPCTs) is investigated. Chemical coating and etching techniques are performed to prepare the surfaces with different wettabilities that is quantified in the form of the contact angle (CA). The 12 TPCTs are processed including the same CA and a different CA combination on the inner surfaces inside both the evaporator and the condenser sections. For TPCTs with the same wettability properties, the introduction of hydrophilic properties inside the evaporator section not only significantly reduces the start-up time but also decreases the start-up temperature. For example, the start-up time of a TPCT with CA = 28° at 40 W, 60 W and 80 W is 46%, 50% and 55% shorter than that of a TPCT with a smooth surface and the wall superheat degrees is 55%, 39% and 28% lower, respectively. For TPCTs with combined hydrophilic and hydrophobic properties, the start-up time spent on the evaporator section with hydrophilic properties is shorter than that of the hydrophobic evaporator section and the smaller CA on the condenser section shows better results. The start-up time of a TPCT with CA = 28° on the evaporator section and CA = 105° on the condenser section has the best start-up process at 40 W, 60 W and 80 W which is 14%, 22% and 26% shorter than that of a TPCT with smooth surface. Thus, the hydrophilic and hydrophobic modifications play a significant role in promoting the start-up process of a TPCT.

Reciprocating-Mechanism Driven Heat Loops and Their Applications

2003 ◽  
Author(s):  
Yiding Cao ◽  
Mingcong Gao
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Electronics Cooling ◽  
Working Fluid ◽  
High Heat Flux ◽  
Two Phase ◽  
Condenser Section ◽  
Evaporator Section ◽  
Two Phase Heat Transfer ◽  
Transfer Device

This paper introduces a novel heat transfer mechanism that facilitates two-phase heat transfer while eliminating the so-called cavitation problem commonly encountered by a conventional pump. The heat transfer device is coined as the reciprocating-mechanism driven heat loop (RMDHL), which includes a hollow loop having an interior flow passage, an amount of working fluid filled within the loop, and a reciprocating driver. The hollow loop has an evaporator section, a condenser section, and a liquid reservoir. The reciprocating driver is integrated with the liquid reservoir and facilitates a reciprocating flow of the working fluid within the loop, so that liquid is supplied from the condenser section to the evaporator section under a substantially saturated condition and the so-called cavitation problem associated with a conventional pump is avoided. The reciprocating driver could be a solenoid-operated reciprocating driver for electronics cooling applications and a bellows-type reciprocating driver for high-temperature applications. Experimental study has been undertaken for a solenoid-operated heat loop in connection with high heat flux thermal management applications. Experimental results show that the heat loop worked very effectively and a heat flux as high as 300 W/cm2 in the evaporator section could be handled. The applications of the bellows-type reciprocating heat loop for gas turbine nozzle guide vanes and the leading edges of hypersonic vehicles are also illustrated. The new heat transfer device is expected to advance the current two-phase heat transfer device and open up a new frontier for further research and development.

Analysis of Heat Pipe Filled with Several Oxide Nanofluids on the Start-Up Process

2014 ◽  
Vol 490-491 ◽  
pp. 251-255 ◽  
Author(s):  
Yu Ying Gong ◽  
Zong Ming Liu ◽  
Wei Lin Zhao
Keyword(s):  
Temperature Distribution ◽  
Heat Pipe ◽  
Temperature Drop ◽  
Heat Pipes ◽  
Condenser Section ◽  
Evaporator Section ◽  
Heating Section ◽  
Start Up

Three heat pipes with nanofluids of Al2O3-water, CuO-water and SiO2-water were tested experimentally. The temperature distribution of their start-up process was analysed, and compared the heat pipe with water. The results showed that the start-up way of heat pipe filled with nanofluids was coincident, the heat pipe filled with nanofluids showed a lower start-up temperature and a shorter start-up time in evaporator section compared with heat pipe filled with water, the temperature drop between evaporator section and condenser section for the heat pipe filled with nanofluids were reduced by 2-5°C than that of the heat pipe filled with water. The effect of the length of the heating section of heat pipe filled with nanofluids on the start-up process was little.

Experimental and Analytical Studies of Reciprocating-Mechanism Driven Heat Loops (RMDHLs)

2008 ◽  
Vol 130 (7) ◽  
Author(s):  
Yiding Cao ◽  
Mingcong Gao
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Electronics Cooling ◽  
High Heat ◽  
Working Fluid ◽  
High Heat Flux ◽  
Two Phase ◽  
Condenser Section ◽  
Analytical Studies ◽  
Evaporator Section

This paper conducts experimental and analytical studies of a novel heat-transfer device, reciprocating-mechanism driven heat loop (RMDHL) that facilitates two-phase heat transfer while eliminating the so-called cavitation problem commonly encountered by a conventional pump. A RMDHL normally includes a hollow loop having an interior flow passage, an amount of working fluid filled within the loop, and a reciprocating driver. The hollow loop has an evaporator section, a condenser section, and a liquid reservoir. The reciprocating driver is integrated with the liquid reservoir and facilitates a reciprocating flow of the working fluid within the loop, so that liquid is supplied from the condenser section to the evaporator section under a substantially saturated condition and the so-called cavitation problem associated with a conventional pump is avoided. The reciprocating driver could be a solenoid-operated reciprocating driver for electronics cooling applications and a bellows-type reciprocating driver for high-temperature applications. Experimental study has been undertaken for a solenoid-operated heat loop in connection with high heat flux thermal management applications. Experimental results show that the heat loop worked very effectively and a heat flux as high as 300W∕cm2 in the evaporator section could be handled. A working criterion has also been derived, which could provide a guidance for the design of a RMDHL.

Effects of Varying Geometrical Parameters on Boiling From Microfabricated Enhanced Structures

2003 ◽  
Vol 125 (1) ◽  
pp. 103-109 ◽  
Author(s):  
C. Ramaswamy ◽  
Y. Joshi ◽  
W. Nakayama ◽  
W. B. Johnson
Keyword(s):  
Heat Dissipation ◽  
Layer Structure ◽  
Single Layer ◽  
Nucleate Boiling ◽  
Heat Fluxes ◽  
Working Fluid ◽  
Geometrical Parameters ◽  
Small Range ◽  
Two Phase ◽  
Wall Superheat

The current study involves two-phase cooling from enhanced structures whose dimensions have been changed systematically using microfabrication techniques. The aim is to optimize the dimensions to maximize the heat transfer. The enhanced structure used in this study consists of a stacked network of interconnecting channels making it highly porous. The effect of varying the pore size, pitch and height on the boiling performance was studied, with fluorocarbon FC-72 as the working fluid. While most of the previous studies on the mechanism of enhanced nucleate boiling have focused on a small range of wall superheats (0–4 K), the present study covers a wider range (as high as 30 K). A larger pore and smaller pitch resulted in higher heat dissipation at all heat fluxes. The effect of stacking multiple layers showed a proportional increase in heat dissipation (with additional layers) in a certain range of wall superheat values only. In the wall superheat range 8–13 K, no appreciable difference was observed between a single layer structure and a three layer structure. A fin effect combined with change in the boiling phenomenon within the sub-surface layers is proposed to explain this effect.

Heat Transport Limitation of a Triangular Micro Heat Pipe

2003 ◽  
Author(s):  
D. Sugumar ◽  
Kek Kiong Tio
Keyword(s):  
Heat Pipe ◽  
Heat Transport ◽  
Operating Temperature ◽  
Working Fluid ◽  
Transport Capacity ◽  
Condenser Section ◽  
Micro Heat Pipe ◽  
Evaporator Section ◽  
Higher Temperature ◽  
Specific Temperature

A micro heat pipe will operate effectively by achieving its maximum possible heat transport capacity only if it is to operate at a specific temperature, i.e., design temperature. In reality, micro heat pipe’s may be required to operate at temperatures different from the design temperature. In this study, the heat transport capacity of an equilateral triangle micro heat pipe is investigated. The micro heat pipe is filled optimally with working fluid for a specific design temperature and operated at different operating temperatures. For this purpose, water, pentane and acetone was selected as the working fluids. From the numerical results obtained, it shows that the optimal charge level of the micro heat pipe is dependent on the operating temperature. Furthermore, the results also shows that if the micro heat pipe is to be operated at temperatures other than its design temperature, its heat transport capacity is limited by the occurrence of flooding at the condenser section or dryout at the evaporator section, depending on the operating temperature and type of working fluid. It is observed that when the micro heat pipe is operated at a higher temperature than its design temperature, the heat transport capacity increases but limited by the onset of dryout at the evaporator section. However, the heat transport capacity decreases if it is to be operated at lower temperatures than its design temperature due to the occurrence of flooding at condenser end. From the results obtained, we can conclude that the performance of a micro heat pipe is decreased if it is to be operated at temperatures other than its design temperature.

Influence of a Hydrophobic Emulsion on the Surface Properties of Coatings of Water-Dispersion Acrylic Paint

2021 ◽  
Vol 1040 ◽  
pp. 165-171
Author(s):  
Valeria V. Strokova ◽  
Maria V. Nikulina ◽  
Pavel S. Baskakov ◽  
Alina V. Abzalilova ◽  
Anastasia Y. Esina
Keyword(s):  
Contact Angle ◽  
Ethylene Glycol ◽  
Building Materials ◽  
Properties Of Coatings ◽  
Hydrophobic Properties ◽  
Water Emulsion ◽  
Water Dispersion ◽  
Acrylic Paint ◽  
Functional Additive ◽  
Contact Wetting Angle

The existing methods of confering hydrophobic properties to various building materials are considered. Obtaining special, including hydrophobic, properties of water-emulsion paints is a very relevant task. Previously, a method was developed for producing an emulsion of a polysiloxane stabilized with polyvinyl alcohol. The paper describes the possibility of using a hydrophobisating emulsion of polyhydrosiloxane as a functional additive for an acrylic water-dispersion paint. This emulsion is capable of forming coatings on dense and porous surfaces with an adjustable contact angle up to 105 °. The use of this emulsion, with its sufficient coalescence for volumetric hydrophobization of coatings, makes it possible to obtain a high contact angle on the surface. In the paper, it was assumed that the partial introduction of small amounts (up to 10 %) of a hydrophobizing emulsion into water-dispersion paints would allow achieving the contact angle of wetting for similar coatings consisting exclusively of emulsion. It is shown that the introduction of small amounts of a hydrophobizing emulsion with an auxiliary coalescing action of ethylene glycol makes it possible to impart hydrophobic properties to the surface of the resulting coating. When the optimum concentration of ethylene glycol in the coating is reached, dissolution and transport (yield) of polysiloxane to the surface is ensured. The research carried out made it possible to develop a paint composition with a hydrophobizing emulsion with a contact wetting angle of about 100 °, which ensured the hydrophobicity of the previously hydrophilic coating of a water-dispersion acrylic paint.

scholarly journals Hydrophobic Properties of tRNA with Varied Conformations Evaluated by an Aqueous Two-Phase System

2012 ◽  
Vol 8 (8) ◽  
pp. 1188-1196 ◽  
Author(s):  
Keishi Suga ◽  
Hibiki Tomita ◽  
Seishiro Tanaka ◽  
Hiroshi Umakoshi
Keyword(s):  
Phase System ◽  
Hydrophobic Properties ◽  
Two Phase ◽  
Aqueous Two Phase System

Dropwise cooling crystallization of ammonium perchlorate in gas–liquid two-phase suspension systems

CrystEngComm ◽  
2018 ◽  
Vol 20 (43) ◽  
pp. 6932-6939 ◽  
Author(s):  
Wei Liu ◽  
Yong Xie ◽  
Qiang Xie ◽  
Kexiong Fang ◽  
Xuan Zhang ◽  
...  
Keyword(s):  
Particle Size ◽  
Particle Size Distribution ◽  
Crystal Engineering ◽  
Smooth Surface ◽  
Narrow Particle Size Distribution ◽  
Two Phase ◽  
Crystalline Materials ◽  
Suspension Systems ◽  
Crystallization Method ◽  
Cooling Crystallization

A dropwise cooling crystallization method was proposed to prepare AP crystals with a uniform shape, a narrow particle size distribution and a smooth surface, which is also a reference for the crystallization of other crystalline materials in crystal engineering.

Capillary Forces Described by Effective Contact Angle Distributions via Simulations of the Centrifuge Technique

MRS Advances ◽  
2016 ◽  
Vol 1 (31) ◽  
pp. 2237-2245
Author(s):  
Myles Thomas ◽  
Elizabeth Krenek ◽  
Stephen Beaudoin
Keyword(s):  
Surface Roughness ◽  
Contact Angle ◽  
Smooth Surface ◽  
Adhesion Force ◽  
Capillary Forces ◽  
Angle Distribution ◽  
Particle Adhesion ◽  
Multiple Factors ◽  
Effective Contact ◽  
Condensed Moisture

ABSTRACTUnderstanding particle adhesion is vital to any industry where particulate systems are involved. There are multiple factors that affect the strength of the adhesion force, including the physical properties of the interacting materials and the system conditions. Surface roughness on the particles and the surfaces to which they adhere, including roughness at the nanoscale, is critically important to the adhesion force. The focus of this work is on the capillary force that dominates the adhesion whenever condensed moisture is present. Theoretical capillary forces were calculated for smooth particles adhered to smooth and rough surfaces. Simulations of the classical centrifuge technique used to describe particle adhesion to surfaces were performed based on these forces. A model was developed to describe the adhesion of the particles to the rough surface in terms of the adhesion to a smooth surface and an ‘effective’ contact angle distribution.

scholarly journals Productivity Influence Factors of Tight Sandstone Gas Reservoir with Water Produced

Geofluids ◽  
2021 ◽  
Vol 2021 ◽  
pp. 1-9
Author(s):  
Yongchao Xue ◽  
Qingshuang Jin ◽  
Hua Tian
Keyword(s):  
Pressure Gradient ◽  
Relative Permeability ◽  
Gas Flow ◽  
Influence Factors ◽  
Stress Sensitivity ◽  
Consumption Pattern ◽  
Tight Sandstone ◽  
Gas Reservoir ◽  
Two Phase ◽  
Start Up

Finding ways to accelerate the effective development of tight sandstone gas reservoirs holds great strategic importance in regard to the improvement of consumption pattern of world energy. The pores and throats of the tight sandstone gas reservoir are small with abundant interstitial materials. Moreover, the mechanism of gas flow is highly complex. This paper is based on the research of a typical tight sandstone gas reservoir in Changqing Oilfield. A strong stress sensitivity in tight sandstone gas reservoir is indicated by the results, and it would be strengthened with the water production; at the same time, a rise to start-up pressure gradient would be given by the water producing process. With the increase in driving pressure gradient, the relative permeability of water also increases gradually, while that of gas decreases instead. Following these results, a model of gas-water two-phase flow has been built, keeping stress sensitivity, start-up pressure gradient, and the change of relative permeability in consideration. It is illustrated by the results of calculations that there is a reduction in the duration of plateau production period and the gas recovery factor during this period if the stress sensitivity and start-up pressure gradient are considered. In contrast to the start-up pressure gradient, stress sensitivity holds a greater influence on gas well productivity.

Sign in / Sign up

Export Citation Format

Share Document