scholarly journals Assessment of Reducing Pollutant Emissions in Selected Heating and Ventilation Systems in Single-Family Houses

Energies ◽  
2020 ◽  
Vol 13 (5) ◽  
pp. 1224 ◽  
Author(s):  
Joanna Hałacz ◽  
Aldona Skotnicka-Siepsiak ◽  
Maciej Neugebauer
Keyword(s):  
Mechanical Ventilation ◽  
Heat Pump ◽  
Carbon Dioxide Emissions ◽  
Natural Ventilation ◽  
Pollutant Emissions ◽  
Single Family ◽  
Heating Systems ◽  
Biomass Boiler ◽  
Final Energy ◽  
Ventilation Systems

The article presents the results of a study aiming to select the optimal source of heat for a newly designed single-family home. Commercial software was used to compare heating and ventilation systems involving a bituminous coal boiler, a condensing gas boiler, a biomass boiler, a heat pump with water and glycol as heat transfer media. The effectiveness of natural ventilation, mechanical ventilation with a ground-coupled heat exchanger, and solar heater panels for water heating were evaluated. The analysis was based on the annual demand for useful energy, final energy, and non-renewable primary energy in view of the pollution output of the evaluated heating systems. The analysis revealed that the heat pump with water and glycol was the optimal solution. However, the performance of the heat pump in real-life conditions was below its maximum theoretical efficiency. The biomass boiler contributed to the highest reduction in pollutant emissions (according to Intergovernmental Panel on Climate Change Change guidelines, carbon dioxide emissions have zero value), but it was characterized by the highest demand for final energy. Mechanical ventilation with heat recovery was required in all analyzed systems to achieve optimal results. The introduction of mechanical ventilation decreased the demand for final energy by 10% to around 40% relative to the corresponding heating systems with natural ventilation.

scholarly journals Assessment of options to reduce pollutant emissions in single-family houses in north-eastern Poland

2020 ◽  
Vol 154 ◽  
pp. 07005
Author(s):  
Joanna Hałacz ◽  
Aldona Skotnicka-Siepsiak ◽  
Maciej Neugebauer ◽  
Krzysztof Nalepa ◽  
Piotr Sołowiej
Keyword(s):  
Heat Transfer ◽  
Mechanical Ventilation ◽  
Heat Exchanger ◽  
Heat Pump ◽  
High Efficiency ◽  
Real Life ◽  
Pollutant Emissions ◽  
Single Family ◽  
Biomass Boiler ◽  
Final Energy

The article presents the results of a study aiming to select the optimal source of heat for a newly designed single-family home. Commercial software was used to compare heating and ventilation systems involving a bituminous coal boiler, a condensing gas boiler, a biomass boiler, and a heat pump with water and glycol as heat transfer media. The effectiveness of natural ventilation, mechanical ventilation with a ground-coupled heat exchanger, and solar heater panels (flat and tubular) for water heating was evaluated. The analysis was based on the annual demand for useful energy, final energy and non-renewable primary energy in view of the pollution output of the evaluated heating systems. The analysis revealed that the heat pump with water and glycol as heat transfer media was the optimal solution. However, the performance of the heat pump in real-life conditions was below its maximum theoretical efficiency. The biomass boiler contributed to the highest reduction in pollutant emissions, but it was characterized by the highest demand for final energy. Mechanical ventilation with heat recovery was required in all analyzed systems to achieve the optimal results. Laboratory analyses confirmed the high efficiency of the tube heat exchanger in winter.

scholarly journals Mapping Relevant Parameters for Efficient Operation of Low-Temperature Heating Systems in Nordic Single-Family Dwellings

2018 ◽  
Vol 8 (10) ◽  
pp. 1973 ◽  
Author(s):  
Adnan Ploskić ◽  
Qian Wang ◽  
Sasan Sadrizadeh
Keyword(s):  
Low Temperature ◽  
Environmental Impact ◽  
Water Flow ◽  
Heat Pump ◽  
Flow Rate ◽  
Water Flow Rate ◽  
Hot Water ◽  
Single Family ◽  
Efficient Operation ◽  
Heating Systems

The aim of this study was to map the parameters that have the greatest impact on the environmental impact of heating systems usually used in Nordic single-family dwellings. The study focused on mapping the technical requirements for efficient operation of heating systems in a broader context. The results suggest that the ability of a heating system to be operated with a low-temperature water supply depends to a large extent on the heating demand of a building. It was shown that an increase in the water flow rate in hydronic circuits would significantly increase the thermal efficiency from analyzed heating systems. This increase would not increase the pumping power need, nor would it create noise problems in distribution network if the distribution pipes and thermostatic valves were properly selected. However, this increase in water flow rate improved the efficiency of considered closed-loop heat pump. It was further shown that the efficiency of the heat pump could be additionally improved by halving the energy needs for the domestic hot-water and circulators. The main conclusion from this study is that exergy usage, CO2 emission and thereby environmental impact are significantly lower for heating systems that are operated with small temperature drops.

scholarly journals Hardware in the Loop Real-Time Simulation for Heating Systems: Model Validation and Dynamics Analysis

2018 ◽  
Author(s):  
Wessam El-Baz ◽  
Lukas Mayerhofer ◽  
Peter Tzscheutschler ◽  
Ulrich Wagner
Keyword(s):  
Heat Pump ◽  
Real Life ◽  
Added Value ◽  
Dynamics Analysis ◽  
Hardware In The Loop ◽  
Single Family ◽  
Heating Systems ◽  
Systems Model ◽  
Operation Method ◽  
First Case

Heating systems such as heat pump and combined heat and power cycle systems (CHP) are representing a key component in the future smart grid. Their capability to couple the electricity and heat sector promises a massive potential to the energy transition. Hence, these systems are continuously studied numerical and experimental to quantify their potential and develop optimal control methods. Although numerical simulations provide time and cost-effective solution for system development and optimization, they are exposed to several uncertainties. Hardware in the loop (HiL) system enables system validation and evaluation under different real-life dynamic constraints and boundary conditions. In this paper, a HiL system of heat pump testbed is presented. This system is used to present two case studies. In the first case, the conventional heat pump testbed operation method is compared to the HiL operation method. Energetic and dynamic analyses are performed to quantify the added value of the HiL and its necessity for dynamics analysis. The second case, the HiL testbed is used to validate the heat pump operation in a single family house participating in a local energy market. It enables not only the dynamics of the heat pump and the space heating circuit to be validated but also the building room temperature. The energetic analysis indicated a deviation of 2% and 5% for heat generation and electricity consumption of the heat pump, respectively. The model dynamics emphasized the model capability to present the dynamics of a real system with a temporal distortion of 3%.

Analysis of Natural Ventilation Systems in Schoolrooms

2016 ◽  
Vol 824 ◽  
pp. 625-632
Author(s):  
Mária Budiaková
Keyword(s):  
Mechanical Ventilation ◽  
Thermal Comfort ◽  
Energy Saving ◽  
Air Temperature ◽  
Natural Ventilation ◽  
Winter Period ◽  
Experimental Measurements ◽  
Air Velocity ◽  
The Future ◽  
Ventilation Systems

The paper is oriented on the analysis of the ventilation systems in schoolrooms. Correct and sufficient ventilation of schoolrooms is very important because students and pupils spend in the schoolrooms the majority of their time in school. In our schools the ventilation is incorrect and insufficient. The biggest problem is winter period when the ventilation is provided only by opening the doors to corridor. This way, there is insufficient intake of oxygen, which causes distractibility and feeling of tiredness of pupils. In current schoolrooms we can use only natural ventilation and thus the schoolrooms have to be ventilated using windows. Therefore this research was focused on the comparison and the analysis of different systems of natural ventilation in schoolrooms. The experimental measurements were carried out in schoolroom, where the parameters of thermal comfort were measured in the different systems of natural ventilation with device Testo 480 which was connected to computer. Gained values of air temperature, air velocity and index PMV are presented in graphs. On the base of analysis of measured values were evaluated the systems of natural ventilation for schoolrooms. In the future, the mechanical ventilation in schoolrooms can be assumed, therefore the recommendation on modern energy saving system of mechanical ventilation is in the end of this paper.

scholarly journals Environmental-economic analysis of the heating system for a single-family building

2018 ◽  
Vol 44 ◽  
pp. 00054
Author(s):  
Agnieszka Jachura
Keyword(s):  
Comparative Analysis ◽  
Economic Analysis ◽  
Heat Pump ◽  
Renewable Energy Sources ◽  
Heating System ◽  
Single Family ◽  
Pump System ◽  
Heat Pump System ◽  
Heating Systems ◽  
Family Building

This paper discusses the use of modern and effective heating systems, using fossil fuels and renewable energy sources on the example of a comparative analysis of a gas boiler and heat pump for a single-family building. The aim of the work was to conduct a comparative analysis of heating systems in terms of energy, economy and ecology. The concepts of heating systems based on a gas boiler and a heat pump are proposed. An economic analysis based on the LCC and ecological method was carried out, related to the equivalent emission, in order to compare the degree of environmental nuisance of the proposed heat sources. For the building in question, a more advantageous solution was the use of a system based on a condensing gas boiler. The economic analysis shows that in the assumed life cycle (20 years), the total cost for a heating system based on a gas boiler is lower than in the case of a heat pump by 11%. Also, the initial costs in this variant are lower by nearly half compared to the heat pump system. Environmental analyzes have shown lower annual emissions of pollutants and a 6-fold lower equivalent emission for a gas-fired heating system.

scholarly journals Hybridization of Heat Pump Systems With Natural Ventilation To Improve Energy Efficiency in Cooling Dominated Buildings

2021 ◽  
Vol 6 ◽  
pp. 33
Author(s):  
Nuno R. Martins ◽  
Peter J. Bourne-Webb
Keyword(s):  
Heat Pump ◽  
Natural Ventilation ◽  
Energy Performance ◽  
Ground Temperature ◽  
Improve Energy Efficiency ◽  
Final Energy ◽  
Heating And Cooling ◽  
Energy Needs ◽  
Energy Simulations ◽  
Cooling Loads

Building foundation piles can be used as heat exchangers in ground-source heat pump (GSHP) systems to provide highly efficient renewable heating and cooling (H&C). Unbalanced H&C loads lead to heat build-up in the ground, decreasing the system's overall performance. In this study, the introduction of natural ventilation (NV) has been examined to decrease cooling load imbalance in cooling-dominated buildings to improve system efficiency. Building energy simulations estimated the H&C loads for an office building in three Portuguese cities: Lisbon, Porto and Faro, yielding heating loads of 0.2–3.6 MWh/year and cooling loads of 260–450 MWh/year. Four renewable H&C technology scenarios were used to assess energy performance: (1) an air-source heat pump (ASHP) system; (2) a GSHP system utilizing energy piles; (3) hybrid ASHP-NV and (4) hybrid GSHP-NV. Over 50 years of operation, in Scenario (1) COP values of 2.45–2.55 (heating) and 3.62–4.15 (cooling) were obtained. In (2), COP values increased to 4.15–4.34 (heating) but fell to 3.36–3.79 (cooling), which increased annual final energy needs by 7–8%. Unbalanced cooling loads increased the ground temperature by 21–24 °C, which is unlikely to be acceptable. Compared to (1), introducing NV reduced cooling loads by 65–90% in Scenarios (3) and (4), with the final energy needs decreasing by 59–80% and 62–88%, respectively. A further benefit of the GSHP-NV hybrid is that the ground temperature increase was limited to 8‑12 °C. For cooling, the COP in (3) decreased compared to (1) (3.14–3.69), while in (4), COP improved to 3.45–6.10. This study concludes that hybrid GSHP-NV systems should be considered in some cooling-dominated scenarios.

scholarly journals Interface of the Natural Ventilation Systems with Building Management Systems

2020 ◽  
Vol 51 (2) ◽  
pp. 178-188
Author(s):  
Ilker Karadag ◽  
Aysem Berrin Cakmakli
Keyword(s):  
Mechanical Ventilation ◽  
Urban Areas ◽  
Natural Ventilation ◽  
Energy Requirement ◽  
Hybrid Approach ◽  
Tall Buildings ◽  
Management Systems ◽  
Building Management ◽  
Building Management Systems ◽  
Ventilation Systems

The vertical city is increasingly being seen as the most viable solution for many urban centers. However, being vertical means constructing tall buildings which imply a large amount of energy requirement mostly due to the mechanical ventilation systems. Replacing these systems with natural ventilation is of importance on the way of achieving sustainable buildings and cities. However, there are many challenges in incorporating natural ventilation systems into tall office buildings. Because, having a far distance from the ground levels, tall buildings are exposed to turbulent and unstable wind conditions. Therefore, advanced technical systems to monitor/control a tall building is required even though natural ventilation is mostly considered a passive, low technological approach to condition a building. These systems utilize sensors to measure internal environmental conditions and external conditions of air temperature, humidity, wind velocity, and rain to utilize passive or active modes, based on the data received. To integrate such systems, in most cases, a hybrid approach is required to fill the gap between the natural and mechanical ventilation systems. Since, climate conditions may not be suitable for solely depending on natural ventilation throughout the year, using mechanical ventilation systems as a back-up to natural ventilation is mostly required. Based on this approach, this study presents advanced natural ventilation strategies of a number of buildings integrating Building Management Systems. Throughout the study, it is intended to guide further researches on natural ventilation and consequently to contribute to the environmental quality of urban areas and smart sustainable development of the cities.

scholarly journals Nosocomial Tuberculosis Transmission from 2006 to 2018 in Beijing Chest Hospital, China

2020 ◽  
Author(s):  
Zhongyao Xie ◽  
Ning Zhou ◽  
Yuqing Chi ◽  
Guofang Huang ◽  
Jingping Wang ◽  
...  
Keyword(s):  
Risk Factors ◽  
Mechanical Ventilation ◽  
Natural Ventilation ◽  
Cox Regression ◽  
Protective Effects ◽  
Cox Regression Analysis ◽  
Tuberculosis Transmission ◽  
Regression Correlation ◽  
Ventilation Systems

Abstract Introduction: Strong evidence is lacking to support effectiveness of currently implemented tuberculosis infection prevention control (TB-IPC) measures for preventing nosocomial tuberculosis (TB) transmission. This 13-year analysis is the longest follow-up investigation to date to identify risk factors underlying nosocomial TB transmission. Methods: We monitored all staff of Beijing Chest Hospital each year from 2006 to 2018. Age, gender, duration, department, education, income, respirator, ultraviolet, and ventilation were chosen as variables. Univariate cox regression, correlation analysis, and multivariate cox regression were analyzed sequentially.Results: Using multivariable cox regression analysis, variables of income, ultraviolet germicidal irradiation (UVGI), natural ventilation and mechanical ventilation conferred significant protective effects, with odds ratios (ORs) of 0.499, 0.058, 0.003, and 0.015, respectively (P<0.05). Medical N95 respirator conferred an excellent protective effect, with an associated TB infection rate of 0%. Notably, inadequately maintained mechanical ventilation systems were less protective than natural ventilation systems.Conclusions: UVGI, adequate ventilation, and use of medical N95 respirator may be risk factors of nosocomial TB transmission.

scholarly journals Comparison of indoor moisture excess in three different terraced housing projects

2021 ◽  
Vol 2069 (1) ◽  
pp. 012041
Author(s):  
C Harreither ◽  
J Gengler ◽  
T Bednar
Keyword(s):  
Mechanical Ventilation ◽  
High Density ◽  
Single Family ◽  
Indoor Temperature ◽  
Housing Projects ◽  
Box Plots ◽  
The Poor ◽  
Indoor Humidity ◽  
Ventilation Systems

Abstract In this study three neighbourhoods of terraced houses have been investigated. In 16 to 29 houses of each project, indoor temperature and indoor humidity have been measured, inhabitants have been interviewed and Blower-Door Tests have been performed. PSG is a project with 91 similar, very airtight detached houses. More than 29 of these houses have been investigated. TES is a low-rise high-density project with 46 single family houses built in 1974. The measuring results of 20 houses with very poor airtightness have been analysed. APW is a project with 26 terraced houses built in 2012, which have mechanical ventilation systems. From APW 16 houses have participated in the study. It will be illustrated that the airtight houses of PSG have the highest absolute indoor humidity, the TES houses with the poor airtightness have medium absolute indoor humidity and the APW with the mechanical ventilation systems have the lowest absolute indoor humidity. Box plots of the moisture excess in the diagram with the humidity classes from EN ISO 13788 [1] show that the boxes do not overlap.

Sign in / Sign up

Export Citation Format

Share Document