scholarly journals A Methodology to Investigate the Deviations between Simple and Detailed Dynamic Methods for the Building Energy Performance Assessment

Energies ◽  
2020 ◽  
Vol 13 (23) ◽  
pp. 6217
Author(s):  
Ilaria Ballarini ◽  
Andrea Costantino ◽  
Enrico Fabrizio ◽  
Vincenzo Corrado
Keyword(s):  
Energy Demand ◽  
Dynamic Models ◽  
Building Energy ◽  
Energy Performance ◽  
Transfer Coefficients ◽  
Study Approach ◽  
Heat Transfer Coefficients ◽  
Heating And Cooling ◽  
Cooling Loads ◽  
Physical Phenomena

The research investigates the validity of the simple hourly method, as introduced by the EN ISO 52016-1 standard, for the assessment of the building energy demand for heating and cooling, by comparing it with a detailed dynamic model (EnergyPlus). A new methodology is provided to identify and quantify the causes of deviations between the models. It consists in the split of the contributions of the air heat balance (AHB) equation by dynamic driving force, and in the adoption of consistency options of the modeling parameters related to specific physical phenomena. A case study approach is adopted in the article to achieve the research objective. The results show that the deviations in the heating and cooling loads between the two calculation methods can be mainly ascribed to the use of different surface heat transfer coefficients, and to a different modeling of the extra thermal radiation to the sky. Providing a methodology to validate the calculation method, this work is intended to contribute to the enhancement of the use of simple dynamic models and to the improvement of the standardization activity.

scholarly journals The modifications to the requirements on energy savings and thermal insulation of buildings in Poland in the years 1974-2021

2015 ◽  
Vol 14 (1) ◽  
pp. 145-154 ◽  
Author(s):  
Anna Życzyńska ◽  
Tomasz Cholewa
Keyword(s):  
Heat Transfer ◽  
Energy Consumption ◽  
Energy Demand ◽  
Energy Savings ◽  
Building Energy ◽  
The European Union ◽  
Transfer Coefficients ◽  
Total Energy Consumption ◽  
Heat Transfer Coefficients ◽  
Technical Requirements

Residential and public buildings use for heating more than 40% of the total energy consumption in the European Union. Therefore, this paper discusses the modifications to the building energy standard, which is currently in force. It is based on the requirements included in the Polish technical building regulations and standards. The proper energy-saving police have been implemented to this kind of consumers to diminish the energy consumption. The analysis pertains to the values of heat transfer coefficients of building partitions as well as the indexes of the energy demand for various types of buildings. The analysis was conducted between 1974 and 2013. Moreover; the changes within this range, which will come into force in 2014 and will continue to 2021, which act in accordance with the technical requirements suitable for buildings, were also discussed. Furthermore, minimal thicknesses of insulation materials which enable meeting this requirements of a heat transfer coefficient for building partitions, were examined in the article.

scholarly journals Impact of Window to Wall Ratio on Energy Loads in Hot Regions: A Study of Building Energy Performance

Energies ◽  
2021 ◽  
Vol 14 (4) ◽  
pp. 1080
Author(s):  
Mamdooh Alwetaishi ◽  
Omrane Benjeddou
Keyword(s):  
Saudi Arabia ◽  
Building Materials ◽  
Building Design ◽  
Building Energy ◽  
Energy Performance ◽  
Design Stage ◽  
Design Solution ◽  
Building Energy Efficiency ◽  
Climatic Regions ◽  
Heating And Cooling

The concern regarding local responsive building design has gained more attention globally as of late. This is due to the issue of the rapid increase in energy consumption in buildings for the purpose of heating and cooling. This has become a crucial issue in educational buildings and especially in schools. The major issue in school buildings in Saudi Arabia is that they are a form of prototype school building design (PSBD). As a result, if there is any concern in the design stage and in relation to the selection of building materials, this will spread throughout the region. In addition to that, the design is repeated regardless of the climate variation within the kingdom of Saudi Arabia. This research will focus on the influence of the window to wall ratio on the energy load in various orientations and different climatic regions. The research will use the energy computer tool TAS Environmental Design Solution Limited (EDSL) to calculate the energy load as well as solar gain. During the visit to the sample schools, a globe thermometer will be used to monitor the globe temperature in the classrooms. This research introduces a framework to assist architects and engineers in selecting the proper window to wall ratio (WWR) in each direction within the same building based on adequate natural light with a minimum reliance on energy load. For ultimate WWR for energy performance and daylight, the WWR should range from 20% to 30%, depending on orientation, in order to provide the optimal daylight factor combined with building energy efficiency. This ratio can be slightly greater in higher altitude locations.

scholarly journals A Study of Optimal Specifications for Light Shelves with Photovoltaic Modules to Improve Indoor Comfort and Save Building Energy

2021 ◽  
Vol 18 (5) ◽  
pp. 2574
Author(s):  
Heangwoo Lee ◽  
Xiaolong Zhao ◽  
Janghoo Seo
Keyword(s):  
Energy Savings ◽  
Building Energy ◽  
Energy Performance ◽  
Building Energy Efficiency ◽  
Efficiency Change ◽  
Photovoltaic Modules ◽  
Heating And Cooling ◽  
Pv Module ◽  
Pv Modules ◽  
Indoor Comfort

Recent studies on light shelves found that building energy efficiency could be maximized by applying photovoltaic (PV) modules to light shelf reflectors. Although PV modules generate a substantial amount of heat and change the consumption of indoor heating and cooling energy, performance evaluations carried out thus far have not considered these factors. This study validated the effectiveness of PV module light shelves and determined optimal specifications while considering heating and cooling energy savings. A full-scale testbed was built to evaluate performance according to light shelf variables. The uniformity ratio was found to improve according to the light shelf angle value and decreased as the PV module installation area increased. It was determined that PV modules should be considered in the design of light shelves as their daylighting and concentration efficiency change according to their angles. PV modules installed on light shelves were also found to change the indoor cooling and heating environment; the degree of such change increased as the area of the PV module increased. Lastly, light shelf specifications for reducing building energy, including heating and cooling energy, were not found to apply to PV modules since PV modules on light shelf reflectors increase building energy consumption.

scholarly journals Full-scale operation of a novel two-pipe active beam system for simultaneous heating and cooling of office buildings

2019 ◽  
Vol 111 ◽  
pp. 01073
Author(s):  
Alessandro Maccarini ◽  
Göran Hultmark ◽  
Niels C. Bergsøe ◽  
Alireza Afshari
Keyword(s):  
Room Temperature ◽  
Energy Performance ◽  
Physical Parameters ◽  
Heating And Cooling ◽  
System A ◽  
A Value ◽  
Beam System ◽  
Simultaneous Heating ◽  
Simultaneous Heating And Cooling ◽  
Cooling Loads

This paper presents an investigation on the operation of a novel active beam system installed in an office building located in Jönköping, Sweden. The system consists of two parts: a dedicated outdoor air system (DOAS) to satisfy latent loads and ventilation requirements, and a water circuit to meet sensible heating and cooling loads. The novelty of the system is in relation to the water circuit, which is able to provide simultaneous heating and cooling through a single water loop that is near the room temperature. The energy performance of the system is currently being monitored through a number of sensors placed along the water circuit. Relevant physical parameters are being measured and data are available through a monitoring system. A preliminary analysis shows that the system is performing as designed. Results are shown for a typical week in winter, spring and summer. In particular, the supply water temperature in the circuit was between 20°C (in summer) and 23.2°C (in winter). The maximum supply/return temperature difference was found in summer and it assumed a value of 1.5 K. It is noticed that in spring supply and return water temperatures almost overlap.

Prediction and Analysis of Building Energy Efficiency Using Artificial Neural Network and Design of Experiments

2016 ◽  
Vol 819 ◽  
pp. 541-545 ◽  
Author(s):  
Sholahudin ◽  
Azimil Gani Alam ◽  
Chang In Baek ◽  
Hwataik Han
Keyword(s):  
Neural Network ◽  
Energy Efficient ◽  
Residential Buildings ◽  
Building Energy ◽  
Cooling Load ◽  
Simulation Data ◽  
Heating And Cooling ◽  
Heating Load ◽  
Input Variables ◽  
Cooling Loads

Energy consumption of buildings is increasing steadily and occupying approximately 30-40% of total energy use. It is important to predict heating and cooling loads of a building in the initial stage of design to find out optimal solutions among various design options, as well as in the operating stage after the building has been completed for energy efficient operation. In this paper, an artificial neural network model has been developed to predict heating and cooling loads of a building based on simulation data for building energy performance. The input variables include relative compactness, surface area, wall area, roof area, overall height, orientation, glazing area, and glazing area distribution of a building, and the output variables include heating load (HL) and cooling load (CL) of the building. The simulation data used for training are the data published in the literature for various 768 residential buildings. ANNs have a merit in estimating output values for given input values satisfactorily, but it has a limitation in acquiring the effects of input variables individually. In order to analyze the effects of the variables, we used a method for design of experiment and conducted ANOVA analysis. The sensitivities of individual variables have been investigated and the most energy efficient solution has been estimated under given conditions. Discussions are included in the paper regarding the variables affecting heating load and cooling load significantly and the effects on heating and cooling loads of residential buildings.

scholarly journals A European Database of Building Energy Profiles to Support the Design of Ground Source Heat Pumps

Energies ◽  
2019 ◽  
Vol 12 (13) ◽  
pp. 2496 ◽  
Author(s):  
Laura Carnieletto ◽  
Borja Badenes ◽  
Marco Belliardi ◽  
Adriana Bernardi ◽  
Samantha Graci ◽  
...  
Keyword(s):  
Heat Pump ◽  
Energy Demand ◽  
Residential Buildings ◽  
Building Energy ◽  
Heat Pumps ◽  
Climatic Conditions ◽  
Ground Source Heat Pumps ◽  
Heating And Cooling ◽  
Energy Profiles ◽  
Ground Source

The design of ground source heat pumps is a fundamental step to ensure the high energy efficiency of heat pump systems throughout their operating years. To enhance the diffusion of ground source heat pump systems, two different tools are developed in the H2020 research project named, “Cheap GSHPs”: A design tool and a decision support system. In both cases, the energy demand of the buildings may not be calculated by the user. The main input data, to evaluate the size of the borehole heat exchangers, is the building energy demand. This paper presents a methodology to correlate energy demand, building typologies, and climatic conditions for different types of residential buildings. Rather than envelope properties, three insulation levels have been considered in different climatic conditions to set up a database of energy profiles. Analyzing European climatic test reference years, 23 locations have been considered. For each location, the overall energy and the mean hourly monthly energy profiles for heating and cooling have been calculated. Pre-calculated profiles are needed to size generation systems and, in particular, ground source heat pumps. For this reason, correlations based on the degree days for heating and cooling demand have been found in order to generalize the results for different buildings. These correlations depend on the Köppen–Geiger climate scale.

scholarly journals Building energy modelling for the energy performance analysis of a hospital building in various locations

2019 ◽  
Vol 111 ◽  
pp. 06073 ◽  
Author(s):  
Ioan Silviu Dobosi ◽  
Cristina Tanasa ◽  
Nicoleta-Elena Kaba ◽  
Adrian Retezan ◽  
Dragos Mihaila
Keyword(s):  
European Union ◽  
Building Energy ◽  
Energy Performance ◽  
Building Envelope ◽  
The European Union ◽  
Total Energy Consumption ◽  
Building Stock ◽  
Heating And Cooling ◽  
Key Factor ◽  
Hospital Building

The building sector has been identified as having the greatest energy reduction potential and therefore represents a key factor for the European Union climate change combat objectives of achieving an 80-95% greenhouse gas emissions reduction by 2050. Hospitals buildings represent 7% of the nonresidential building stock in the European Union and are responsible for approximately 10% of the total energy consumption in this sector. The design and construction of hospital buildings is a complex and challenging activity for all the involved specialists, especially when energy performance is one of the objectives. This paper discusses the energy performance simulation on an hourly basis of a new hospital building that was constructed in the city of Mioveni, Romania. At this stage of the study, the building energy model solely investigates the performance of the building envelope, without modelling the HVAC system. The complexity of the building model derives from the multitude of thermal zones depending on interior temperature and ventilation air changes conditions. Several simulations are performed investigating the heating and cooling energy need depending on the building location.

Sign in / Sign up

Export Citation Format

Share Document