scholarly journals Economic Feasibility of Photovoltaic Micro-Installations Connected to the Brazilian Distribution Grid in Light of Proposed Changes to Regulations

Energies ◽  
2021 ◽  
Vol 14 (6) ◽  
pp. 1529
Author(s):  
Gabriel Nasser Doyle de Doile ◽  
Paulo Rotella Junior ◽  
Priscila França Gonzaga Carneiro ◽  
Rogério Santana Peruchi ◽  
Luiz Célio Souza Rocha ◽  
...  
Keyword(s):  
Regulatory Agency ◽  
Energy Demand ◽  
Distribution Systems ◽  
Electrical Energy ◽  
Economic Feasibility ◽  
Distribution Grid ◽  
Cost Of Energy ◽  
Before And After ◽  
Scientific Papers ◽  
The Cost

Brazil is currently undergoing changes to regulations on distributed generation (DG), specifically for solar energy micro-generation. The changes proposed by the Brazilian Regulatory Agency suggest that only the cost of energy be compensated to investors. The service costs and other charges related to energy tariffs must be divided among consumers. Investors with existing installations and class entities have contested these proposals, calling them “sun-fees”. To date, no scientific papers have been published discussing these changes. The new regulations propose an end to cross subsidies, where all consumers (even those who do not have DG) pay for the transmission and distribution systems. This study compares the economic feasibility of micro-generation before and after implementing the new standards proposed by the regulatory agency. We used data on average electrical energy demand, energy price, and solar radiation in different regions. The national averages were used as a base comparison with other scenarios. The results show that projects are viable for all analyzed scenarios, however, after implementing the proposed changes, the discounted payback time is extended. This, however, does not make projects unfeasible.

scholarly journals Techno-Economic Feasibility Study of Investigation of Renewable Energy System for Rural Electrification in South Algeria

2018 ◽  
Vol 8 (5) ◽  
pp. 3421-3426 ◽  
Author(s):  
F. Chermat ◽  
M. Khemliche ◽  
A. E. Badoud ◽  
S. Latreche
Keyword(s):  
Greenhouse Gas Emission ◽  
Electrical Energy ◽  
Energy System ◽  
Economic Feasibility ◽  
Maintenance Cost ◽  
Management Algorithm ◽  
Cost Of Energy ◽  
The Cost ◽  
Operation And Maintenance Cost ◽  
Different Sources

This work aims to consider the combination of different technologies regarding energy production and management with four possible configurations. We present an energy management algorithm to detect the best design and the best configuration from the combination of different sources. This combination allows us to produce the necessary electrical energy for supplying habitation without interruption. A comparative study is conducted among the different combinations on the basis of the cost of energy, diesel consumption, diesel price, capital cost, replacement cost, operation, and maintenance cost and greenhouse gas emission. Sensitivity analysis is also performed.

scholarly journals The results of the competitiveness analysis of photovoltaic microgeneration systems in the Russian Federation

2019 ◽  
Vol 486 (5) ◽  
pp. 543-546
Author(s):  
T. S. Gabderakhmanova ◽  
O. S. Popel
Keyword(s):  
Energy Storage ◽  
Dynamic Modelling ◽  
Electrical Energy ◽  
Economic Feasibility ◽  
Government Support ◽  
Feasibility Assessment ◽  
Pv Systems ◽  
Cost Of Energy ◽  
Regulatory Standards ◽  
The Cost

The results of the economic feasibility assessment of photovoltaic (PV) microgeneration systems by the criterion of the cost of energy are presented. The assessment is based on dynamic modelling of three different configurations of grid-connected PV systems - without energy storage, with electrical energy storage and with thermal energy storage - performed for weather and electricity tariff conditions of several prospective Russian regions. Government support measures and regulatory standards currently developing in Russia for microgeneration technologies are taken into account. It is shown that under certain conditions PV microgeneration technologies could be economically feasible in some energy isolated areas and non-pricing zones of the wholesale electricity and capacity market of Russia, particularly in the Sakha Republic, whereas in pricing zones - couldn’t for any of the considered system configurations.

scholarly journals Green Hydrogen Value Chain in the Sustainability for Port Operations: Case Study in the Region of Valparaiso, Chile

2021 ◽  
Vol 13 (24) ◽  
pp. 13681
Author(s):  
Yunesky Masip Macía ◽  
Pablo Rodríguez Machuca ◽  
Angel Alexander Rodríguez Soto ◽  
Roberto Carmona Campos
Keyword(s):  
Fuel Cell ◽  
Value Chain ◽  
Energy Demand ◽  
Large Scale ◽  
Electrical Energy ◽  
Diesel Generator ◽  
Cost Of Energy ◽  
Main Components ◽  
The Cost ◽  
Port Facility

The paper presents a complete value chain for the use of green hydrogen in a port facility. The main objective was to propose the sizing of the main components that make up green hydrogen to ensure the supply of 1 MWe in replacing the diesel generator. The energy demand required for the port was determined by establishing the leading small and large-scale conventional energy-consuming equipment. Hence, 60 kgH2 was required to ensure the power supply. The total electrical energy to produce all the hydrogen was generated from photovoltaic solar energy, considering three-generation scenarios (minimum, maximum and the annual average). In all cases, the energy supply in the electrolyzer was 3.08 MWe. In addition, the effect of generating in the port facility using a diesel generator and a fuel cell was compared. The cost of 1 kgH2 could be 4.09 times higher than the cost of 1 L of diesel, meaning that the output kWh of each system is economically similar. In addition, the value of electrical energy through a Power Purchase Agreement (PPA) was a maximum of 79.79 times the value of a liter of diesel. Finally, the Levelized Cost of Energy (LCOE) was calculated for two conditions in which the MWe was obtained from the fuel cell without and with the photovoltaic solar plant.

scholarly journals A Theoretical Study on Reversible Solid Oxide Cells as Key Enablers of Cyclic Conversion between Electrical Energy and Fuel

Energies ◽  
2021 ◽  
Vol 14 (15) ◽  
pp. 4517
Author(s):  
Saheli Biswas ◽  
Shambhu Singh Rathore ◽  
Aniruddha Pramod Kulkarni ◽  
Sarbjit Giddey ◽  
Sankar Bhattacharya
Keyword(s):  
Energy Demand ◽  
Electrode Materials ◽  
Scale Up ◽  
High Capacity ◽  
Electrical Energy ◽  
Solid Oxide ◽  
Lower Efficiency ◽  
Internal Reforming ◽  
Fuels And Chemicals ◽  
The Cost

Reversible solid oxide cells (rSOC) enable the efficient cyclic conversion between electrical and chemical energy in the form of fuels and chemicals, thereby providing a pathway for long-term and high-capacity energy storage. Amongst the different fuels under investigation, hydrogen, methane, and ammonia have gained immense attention as carbon-neutral energy vectors. Here we have compared the energy efficiency and the energy demand of rSOC based on these three fuels. In the fuel cell mode of operation (energy generation), two different routes have been considered for both methane and ammonia; Routes 1 and 2 involve internal reforming (in the case of methane) or cracking (in the case of ammonia) and external reforming or cracking, respectively. The use of hydrogen as fuel provides the highest round-trip efficiency (62.1%) followed by methane by Route 1 (43.4%), ammonia by Route 2 (41.1%), methane by Route 2 (40.4%), and ammonia by Route 1 (39.2%). The lower efficiency of internal ammonia cracking as opposed to its external counterpart can be attributed to the insufficient catalytic activity and stability of the state-of-the-art fuel electrode materials, which is a major hindrance to the scale-up of this technology. A preliminary cost estimate showed that the price of hydrogen, methane and ammonia produced in SOEC mode would be ~1.91, 3.63, and 0.48 $/kg, respectively. In SOFC mode, the cost of electricity generation using hydrogen, internally reformed methane, and internally cracked ammonia would be ~52.34, 46.30, and 47.11 $/MWh, respectively.

scholarly journals Optimized Placement of Connecting the Distributed Generationswork Stand Alone to Improve the Distribution Systems Reliability

2013 ◽  
Vol 64 (2) ◽  
pp. 76-83
Author(s):  
Hamed Hashemi-Dezaki ◽  
Ali Agheli ◽  
Behrooz Vahidi ◽  
Hossein Askarian-Abyaneh
Keyword(s):  
Genetic Algorithm ◽  
Objective Function ◽  
System Reliability ◽  
Distribution Systems ◽  
Analytical Approach ◽  
Distributed Generations ◽  
Joint Point ◽  
Cost Of Energy ◽  
Optimum Solution ◽  
The Cost

The use of distributed generations (DGs) in distribution systems has been common in recent years. Some DGs work stand alone and it is possible to improve the system reliability by connecting these DGs to system. The joint point of DGs is an important parameter in the system designing. In this paper, a novel methodology is proposed to find the optimum solution in order to make a proper decision about DGs connection. In the proposed method, a novel objective function is introduced which includes the cost of connector lines between DGs and network and the cost of energy not supplied (CENS) savings. Furthermore, an analytical approach is used to calculate the CENS decrement. To solve the introduced nonlinear optimization programming, the genetic algorithm (GA) is used. The proposed method is applied to a realistic 183-bus system of Tehran Regional Electrical Company (TREC). The results illustrate the effectiveness of the method to improve the system reliability by connecting the DGs work stand alone in proper placements.

RESEARCH OF ENERGY EFFICIENCY OF TWO-CHAMBER PULSE DEVICES FOR STAMPING

2021 ◽  
pp. 128-133
Author(s):  
А.Ю. Боташев ◽  
А.А. Мусаев
Keyword(s):  
Energy Efficiency ◽  
Combustion Chamber ◽  
Electrical Energy ◽  
Energy Carrier ◽  
Thermodynamic Efficiency ◽  
Total Energy Consumption ◽  
Cost Of Energy ◽  
Sheet Stamping ◽  
Fuel Mixtures ◽  
The Cost

Одной из разновидностей устройств, осуществляющих импульсные методы обработки давлением, являются двухкамерные устройства для листовой штамповки, использующие в качестве энергоносителя газовоздушные топливные смеси. Подача сжатого воздуха в камеру сгорания в рассматриваемом двухкамерном устройстве для листовой штамповки осуществляется компрессором. Проведен анализ термодинамических процессов, протекающих в камере сгорания и рабочем цилиндре двухкамерного устройства для листовой штамповки. При этом установлено, что энергия, затрачиваемая на работу компрессора, составляет около 45% от энергии, выделяющейся в камере сгорания. Получена зависимость для определения термодинамического КПД двухкамерных устройств для листовой штамповки, величина его составляет около 0,25. Установлено, что энергоэффективность двухкамерных устройств не уступает энергоэффективности традиционного штамповочного оборудования, при этом затраты на энергоносители двухкамерных устройств ниже за счет использования дешевого энергоносителя. В двухкамерном штамповочном устройстве для листовой штамповки электрическая энергия, используемая на работу компрессора, составляет менее 1/3 общей потребляемой энергии устройства. Поэтому при прочих равных условиях расходы на энергоносители будут значительно меньше, чем в штамповочном оборудовании, работающем на электрическом токе One of the types of devices that carry out pulse methods of pressure treatment are two-chamber devices for sheet stamping, using gas-air fuel mixtures as an energy carrier. The supply of compressed air to the combustion chamber in the considered two-chamber device for sheet stamping is carried out by a compressor. We carried out the analysis of thermodynamic processes taking place in the combustion chamber and the working cylinder of a two-chamber device for sheet stamping. We found that the energy spent on the operation of the compressor is about 45% of the energy released in the combustion chamber. We obtained the dependence for determining the thermodynamic efficiency of two-chamber devices for sheet stamping; its value is about 0.25. We established that the energy efficiency of two-chamber devices is not inferior to the energy efficiency of traditional stamping equipment, while the energy costs of two-chamber devices are lower due to the use of a cheap energy carrier. In a two-chamber die-forging device for sheet metal stamping, the electrical energy used to operate the compressor is less than 1/3 of the total energy consumption of the device. Therefore, all other things being equal, the cost of energy carriers will be significantly less than in stamping equipment operating on electric current

scholarly journals A Feasibility Study of Cellulosic Isobutanol Production—Process Simulation and Economic Analysis

Processes ◽  
2019 ◽  
Vol 7 (10) ◽  
pp. 667 ◽  
Author(s):  
Avraam Roussos ◽  
Nikiforos Misailidis ◽  
Alexandros Koulouris ◽  
Francesco Zimbardi ◽  
Demetri Petrides
Keyword(s):  
Energy Demand ◽  
Production Cost ◽  
Fossil Fuels ◽  
Raw Materials ◽  
Downstream Processing ◽  
Economic Feasibility ◽  
Unit Production Cost ◽  
Product Titer ◽  
Product Removal ◽  
The Cost

Renewable liquid biofuels for transportation have recently attracted enormous global attention due to their potential to provide a sustainable alternative to fossil fuels. In recent years, the attention has shifted from first-generation bioethanol to the production of higher molecular weight alcohols, such as biobutanol, from cellulosic feedstocks. The economic feasibility of such processes depends on several parameters such as the cost of raw materials, the fermentation performance and the energy demand for the pretreatment of biomass and downstream processing. In this work, two conceptual process scenarios for isobutanol production, one with and one without integrated product removal from the fermentor by vacuum stripping, were developed and evaluated using SuperPro Designer®. In agreement with previous publications, it was concluded that the fermentation titer is a crucial parameter for the economic competitiveness of the process as it is closely related to the energy requirements for product purification. In the first scenario where the product titer was 22 g/L, the energy demand for downstream processing was 15.8 MJ/L isobutanol and the unit production cost of isobutanol was $2.24/L. The integrated product removal by vacuum stripping implemented in the second scenario was assumed to improve the isobutanol titer to 50 g/L. In this case, the energy demand for the product removal (electricity) and downstream processing were 1.8 MJ/L isobutanol and 10 MJ/L isobutanol, respectively, and the unit production cost was reduced to $1.42/L. The uncertainty associated with the choice of modeling and economic parameters was investigated by Monte Carlo simulation sensitivity analysis.

Techno-Economic Feasibility Analysis of Pumped Storage Hydroelectricity in Abandoned Underground Coal Mines

2020 ◽  
Vol 142 (12) ◽  
Author(s):  
Dacheng Shang ◽  
Peng Pei ◽  
Yujun Zuo
Keyword(s):  
Coal Seam ◽  
Capital Investment ◽  
Economic Feasibility ◽  
Abandoned Mines ◽  
Cost Of Energy ◽  
Calculation Results ◽  
Pumped Storage ◽  
Geological Constraints ◽  
The Cost ◽  
Cycle Efficiency

Abstract It is anticipated that utilizing the underground space in abandoned mines to build and operate pumped-storage hydroelectricity (PSH) plants can reduce capital investment and geological constraints. However, there are currently few detailed investigations into techno-economic feasibility except for conceptual studies. In this paper, an underground coal mine in Guizhou, China was used as a reference, and the PSH layout was designed; in addition, the head loss, plant efficiency, and major cost components were investigated. The calculation results show that the capital investment of mine-based PSH was 33–50% less than that of conventional PSH. Sensitivity analysis found a clear influence of coal seam inclination on the performance of the mine-based PSH. Under the assumed conditions, the plant cycle efficiency increased from 62.7% to 71.5% when the coal seam dip varied from 5 deg to 25 deg. Depending on different price scenarios, when the coal seam inclination was steep enough, the cost of energy storage of a mine-based PSH plant was competitive compared with conventional PSH, and the plant could even become profitable. The influence of the dip of coal seam was more pronounced when in the lower range (5–15 deg) than the higher range (15–25 deg).

scholarly journals Photovoltaic Solar Energy: Is It Applicable in Brazil? – A Review Applied to Brazilian Case

2019 ◽  
Vol 66 (2) ◽  
pp. 99-120
Author(s):  
Wilmer Emilio García Moreno ◽  
Andressa Ullmann Duarte ◽  
Litiéle dos Santos ◽  
Rogério Vescia Lourega
Keyword(s):  
Solar Cells ◽  
Solar Cell ◽  
Solar Energy ◽  
Energy Demand ◽  
Fossil Fuels ◽  
Cost Of Energy ◽  
Photovoltaic Solar Energy ◽  
The Cost ◽  
Photovoltaic Technologies ◽  
Brazilian Case

AbstractThe photovoltaic technologies have been developed year by year in different countries; however, there are some countries where this kind of energy is being born, such as the Brazilian case. In this paper, some important parameters are analysed and applied to different solar cell materials, identifying that if the fossil fuels were substituted by solar cells, it would reduce the CO2 emissions by 93.2%. In addition, it is shown that the efficiency of solar cells is not as farther as it could be thought from coal thermoelectrical plants in Brazil and the cost of energy using solar cells could be as good as these thermoelectrical plants. Finally, the potentiality of Brazilian territory to implant this technology is presented, identifying that with the use of 0.2% of the territory, the energy demand could be supplied.

Hybrid Distributed Power Generation for an Isolated Rural Settlement in Masirah Island, Oman

2011 ◽  
Author(s):  
Saleh Al Saadi ◽  
Moncef Krarti
Keyword(s):  
Power Systems ◽  
Residential Buildings ◽  
Renewable Energy Sources ◽  
Electrical Energy ◽  
Small Community ◽  
Solar Pv ◽  
Cost Of Energy ◽  
Storage Batteries ◽  
Electrical Generation ◽  
The Cost

This paper summarizes the findings from a feasibility study of using renewable energy sources in combination with conventional power systems to meet the electrical requirements for an isolated island of Masirah in Oman. The study has been conducted to determine the best hybrid system to generate electrical energy needed for a small community of 500 residential buildings. A series of a simulation analyses have been carried out to evaluate and optimize different distribution technologies including photovolatics, wind and diesel for electrical generation in combination with storage batteries. It was found that the cost of energy could be reduced by as much as 48% compared to the cost for the baseline generation system currently used in the Masirah Island (i.e. diesel-driven generators). In particular, it was found that wind turbines in combination with storage batteries have a great impact in reducing the cost of generating electrical energy for the residential community. Moreover, solar PV panels were found unattractive under the current diesel price rates but could potentially become viable if the diesel prices increase. The paper outlines an optimal design for generating electricity for the community at lowest cost while minimizing carbon emissions.

Sign in / Sign up

Export Citation Format

Share Document