scholarly journals Effect of Microstructures on the Shear Strength of Larix kaempferi

Forests ◽  
2021 ◽  
Vol 12 (7) ◽  
pp. 830
Author(s):  
Mingyue Li ◽  
Shuangbao Zhang ◽  
Yurong Wang ◽  
Haiqing Ren
Keyword(s):  
Cell Wall ◽  
Shear Strength ◽  
Failure Mode ◽  
Wall Thickness ◽  
Shear Failure ◽  
Microfibril Angle ◽  
Cell Wall Thickness ◽  
Larix Kaempferi ◽  
Significant Difference ◽  
Shear Performance

Shear strength is important for the application of Larix kaempferi (Lamb) Carr. The structural difference between earlywood and latewood of Larix kaempferi affects its mechanical properties, especially shear strength. The microstructures of earlywood and latewood in Larix kaempferi, however, are different. In this study, we investigated the shear strength and shear failure mode in the RL direction of 40 Larix kaempferi specimens. The results demonstrated that the initial crack appears in any location of a growth ring, whereas shear failure is concentrated in earlywood, as well as the junction between earlywood and latewood. The destruction of earlywood is the tear destruction, whereas when the destruction happened in the junction of earlywood and latewood, one to three earlywood cells usually adhered to latewood. At the cell wall level, the shear failure of earlywood was mostly observed in the direction of the microfibril angle (MFA). When the crack occurs in latewood, the destruction of latewood also occurs in the intercellular layer and preserves the complete morphology of tracheids. When destruction occurs in the wood ray, the ray cells detach intact from the tracheids. The failure mode is determined by the microstructure of earlywood and latewood. Our research suggests that the density, cell wall thickness, and MFA have significant differences between earlywood and latewood. The earlywood was found to have an MFA of 25.4°, a cell wall thickness of 6.36 µm, and a density of 0.39 g/cm3. The MFA, cell wall thickness, and density of latewood density were 17.60°, 12.37 µm, and 0.78 g/cm3, respectively. However, there was no significant difference found in the crystallinity between the earlywood (43.97%) and latewood (42.79%). The correlation between the microstructures and shear strength showed that earlywood with a thin cell wall, large MFA, and low density had poor shear performance, while the latewood with a thicker tracheid, smaller MFA, and higher density had better shear performance. Therefore, when shear failure occurred, it occurred in earlywood. We thus deduced that the MFA, cell wall thickness, and density of earlywood synergically affect the shear strength in the RL direction of L. kaempferi.

Properties of Gliricidia Wood (Gliricidia sepium) lntercropped with Cocoa (Theobroma cocoa) in Malaysia

2014 ◽  
Vol 11 (1) ◽  
pp. 51
Author(s):  
Mohd Helmy Ibrahim ◽  
Mohd Nazip Suratman ◽  
Razali Abd Kader
Keyword(s):  
Cell Wall ◽  
Specific Gravity ◽  
Moisture Content ◽  
Wall Thickness ◽  
Age Groups ◽  
Gliricidia Sepium ◽  
Cell Wall Thickness ◽  
Tree Age ◽  
Lumen Diameter ◽  
Significant Difference

Trees planted from agroforestry practices can become valuable resources in meeting the wood requirements of many nations. Gliricidia sepium is an exotic species introduced to the agricultural sector in Malaysia mainly for providing shade for cocoa and coffee plantations. This study investigates its wood physical properties (specific gravity and moisture content) and fibre morphology (length, lumen diameter and cell wall thickness) of G. sepium at three intervals according to age groups ( three, five and seven years of ages). Specific gravity (0.72) was significantly higher at seven years ofage as compared to five (0.41) and three (0.35) years age group with a mean of 0.43 (p<0.05). Mean moisture content was 58.3% with no significant difference existing between the tree age groups. Fibre diameter (22.4 mm) was significantly lower (p<0.05) for the trees which were three years of age when compared to five and seven years age groups (26.6 mm and 24. 7 mm), respectively. Means of fibre length, lumen diameter and cell wall thickness were 0.83 mm, 18.3 mm, and 6.2 mm, respectively, with no significant differences detected between trees in all age groups. Further calculation on the coefficient of suppleness and runkel ratio suggest that wood from G.sepium may have the potential for insulation board manufacturing and paper making. However, future studies should experiment the utilisation of this species for these products to determine its full potential.

scholarly journals Evaluation of physical, anatomical, and biometric characteristics of Citrus sinensis trees in longitudinal and transverse axes of stem

BioResources ◽  
2020 ◽  
Vol 15 (3) ◽  
pp. 5696-5709
Author(s):  
Ali Hassanpoor Tichi ◽  
Habibollah Khademieslam ◽  
Mojtaba Rezanezhad Divkolae
Keyword(s):  
Cell Wall ◽  
Wall Thickness ◽  
Citrus Sinensis ◽  
Fiber Length ◽  
Fiber Diameter ◽  
Basic Density ◽  
Cell Wall Thickness ◽  
Lumen Diameter ◽  
Dry Density ◽  
Significant Difference

Three healthy Citrus sinensis (orange) trees in Babol, Iran, were randomly selected and cut. Two discs of 5 cm thickness were prepared along the tree (breast height and crown). In the transverse direction, the test specimens were cut 2 × 2 cm to 3 cm from the pith to the bark sequentially and examined. The biometric and physical properties were measured, and microscopic sections of wood near the bark were studied using light microscopy according to the International Association of Wood Anatomists’ (IAWA) List. Anatomical examination of the C. sinensis wood showed that the species was a diffuse porous hardwood, with indistinct growth rings, simple perforation plates, alternate intervessel pits, and banded parenchyma. The basic density and oven-dry density increased from the pith towards the tree bark and from the bottom of the tree towards the crown. There was a significant difference in both the transverse and longitudinal directions of the C. sinensis tree in terms of fiber length, fiber lumen diameter, fiber diameter, and cell wall thickness. The mean fiber length, fiber diameter, fiber lumen diameter, and cell wall thickness were 0.76 mm, 23.64 µm, 9.23 µm, and 14.41 µm, respectively.

Properties of Gliricidia Wood (Gliricidia sepium) lntercropped with Cocoa (Theobroma cocoa) in Malaysia

2014 ◽  
Vol 11 (1) ◽  
pp. 51
Author(s):  
Mohd Helmy Ibrahim ◽  
Mohd Nazip Suratman ◽  
Razali Abd Kader
Keyword(s):  
Cell Wall ◽  
Specific Gravity ◽  
Moisture Content ◽  
Wall Thickness ◽  
Age Groups ◽  
Cell Wall Thickness ◽  
Tree Age ◽  
Lumen Diameter ◽  
Full Potential ◽  
Significant Difference

Trees planted from agroforestry practices can become valuable resources in meeting the wood requirements of many nations. Gliricidia septum is an exotic species introduced to the agricultural sector in Malaysia mainly for providing shade for cocoa and coffee plantations. This study investigates its wood physical properties (specific gravity and moisture content) and fibre morphology (length, lumen diameter and cell wall thickness) of G.sepium at three intervals according to age groups (three, five and seven years of ages). Specific gravity (0.72) was significantly higher at seven years of age as compared to five (0.4 I) and three (0.35) years age group with a mean of 0.43 (p<0.05). Mean moisture content was 58.3% with no significant difference existing between the tree age groups. Fibre diameter (22.4 mm) was significantly lower (p<0.05) for the trees which were three years of age when compared to five and seven years age groups (26.6 mm and 24. 7 mm), respectively. Means of fibre length, lumen diameter and cell wall thickness were 0.83 mm, 18.3 mm, and 6.2 mm, respectively,, with no significant differences detected between trees in all age groups. Further calculation on the coefficient of suppleness and runkel ratio suggest that wood from G.sepium may have the potential for insulation board manufacturing and paper making. However, future studies should experiment the utilisation of this species for these products to determine its full potential.

scholarly journals Comparative studies on the mechanical properties and microstructures of outerwood and corewood in Pinus radiata D. Don

2021 ◽  
Vol 67 (1) ◽  
Author(s):  
Ming-yue Li ◽  
Hai-qing Ren ◽  
Yu-rong Wang ◽  
Ying-chun Gong ◽  
Yong-dong Zhou
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Cell Wall ◽  
Crystallite Size ◽  
Wall Thickness ◽  
Pinus Radiata ◽  
Microfibril Angle ◽  
Cell Wall Thickness ◽  
Modulus Of Rupture ◽  
Relative Crystallinity

AbstractTwenty-year-old Pinus radiata trees imported from New Zealand were investigated, and a comparison was made between the outerwood (rings 16–20) and corewood (rings 4–6) in terms of mechanical properties, anatomical characteristics, microfibril angle (MFA), relative crystallinity, crystallite size and lignin content to determine the relationship between their mechanical properties and microstructures. The results demonstrated that the mechanical properties of the Pinus radiata outerwood were significantly better than those of the corewood. The outerwood had a modulus of rupture (MOR) of 106 MPa, a modulus of elasticity (MOE) of 11.4 GPa, and compressive strength parallel to the grain of 38.7 MPa, and the MOR, MOE and compressive strength parallel to the grain of the corewood were 78.9 MPa, 7.12 GPa and 29.3 MPa, respectively. The observed microstructures of the Pinus radiata outerwood and corewood were different, mainly due to differences in cell wall thickness, MFA, and relative crystallinity. The double wall thickness of the tracheid cells of the corewood and outerwood were 3.65 and 5.02 µm, respectively. The MFA data indicated that the average MFA of the outerwood was 14.0°, which was smaller than that of the corewood (22.3°). With X-ray diffraction, the relative crystallinity of the corewood was determined to be 35.7%, while that of the outerwood was 40.2%. However, the crystallite size of the outerwood cell wall shows no obvious difference from that of the corewood. Imaging FTIR spectroscopy showed a slightly higher relative content of lignin in the cell wall of the outerwood. The correlation between the microstructures and mechanical properties showed that the corewood with a thin cell wall, large MFA and low relative crystallinity had poor mechanical properties, while the outerwood with a thicker tracheid, smaller MFA and higher relative crystallinity had better mechanical properties. This means that the MFA, relative crystallinity and cell wall thickness synergically affect the mechanical properties of Pinus radiata in different radial locations.

Characterization of microstructures of SAN foam core using micro-computed tomography

2021 ◽  
pp. 026248932110068
Author(s):  
Youming Chen ◽  
Raj Das ◽  
Hui Wang ◽  
Mark Battley
Keyword(s):  
Cell Wall ◽  
Cell Size ◽  
Wall Thickness ◽  
Strain Localization ◽  
Cell Wall Thickness ◽  
Micro Computed Tomography ◽  
Average Cell Size ◽  
Average Cell ◽  
3D Images ◽  
Compressive Tests

In this study, the microstructure of a SAN foam was imaged using a micro-CT scanner. Through image processing and analysis, variations in density, cell wall thickness and cell size in the foam were quantitatively explored. It is found that cells in the foam are not elongated in the thickness (or rise) direction of foam sheets, but rather equiaxed. Cell walls in the foam are significantly straight. Density, cell size and cell wall thickness all vary along the thickness direction of foam sheets. The low density in the vicinity of one face of foam sheets leads to low compressive stiffness and strength, resulting in the strain localization observed in our previous compressive tests. For M80, large open cells on the top face of foam sheets are likely to buckle in compressive tests, therefore being another potential contributor to the strain localization as well. The average cell wall thickness measured from 2D slice images is around 1.4 times that measured from 3D images, and the average cell size measured from 2D slice images is about 13.8% smaller than that measured from 3D images. The dispersions of cell wall thickness measured from 2D slice images are 1.16–1.20 times those measured from 3D images. The dispersions of cell size measured from 2D slice images are 1.12–1.36 times those measured from 3D images.

Summer temperature in northeastern Siberia since 1642 reconstructed from tracheid dimensions and cell numbers of Larix cajanderi

2003 ◽  
Vol 33 (10) ◽  
pp. 1905-1914 ◽  
Author(s):  
Irina P Panyushkina ◽  
Malcolm K Hughes ◽  
Eugene A Vaganov ◽  
Martin AR Munro
Keyword(s):  
Cell Wall ◽  
Wall Thickness ◽  
Cell Number ◽  
Cell Wall Thickness ◽  
Cell Dimension ◽  
Cell Numbers ◽  
Age Related ◽  
Cambial Age ◽  
Northeastern Siberia ◽  
Larix Cajanderi

We reconstructed air temperature for two periods in the growth season from cell dimension and cell number variability in cross-dated tree rings of Larix cajanderi Mayr. from northeastern Siberia. Thirteen tree-ring chronologies based on cell size, cell wall thickness, and cell number were developed for AD 1642–1993. No clear evidence was found of an age-related trend in cell dimensions in the sampled materials, but cell numbers were correlated with cambial age. The chronologies contain strong temperature signals associated with the timing of xylem growth. We obtained reliable reconstructions of mean June temperature from the total cell number and July–September temperature from the cell wall thickness of latewood. June temperature and July–September temperature covaried for most of the period from AD 1642 to AD 1978. After that time, June temperature became cooler relative to July–September temperature. This difference caused disproportional changes in earlywood tracheids because of the late start of growth and cool conditions in June followed by warming during the rest of the season. The identification of this unusual recent change has shown that intraseasonal resolution may be achieved by cell dimension and cell number chronologies.

Variation in xylem anatomy of selected populations of lodgepole pine

2001 ◽  
Vol 31 (11) ◽  
pp. 2049-2057 ◽  
Author(s):  
Tongli Wang ◽  
Sally N Aitken
Keyword(s):  
Cell Wall ◽  
Wall Thickness ◽  
Slow Growth ◽  
Lodgepole Pine ◽  
High Density ◽  
Cell Wall Thickness ◽  
Fast Growth ◽  
Low Density ◽  
Xylem Anatomy ◽  
Latewood Density

Variation in xylem anatomy among selected populations of lodgepole pine (Pinus contorta Dougl. ex Loud. var. latifolia Engelm.) was examined using digital image analysis based on an annual growth ring (age 10) per tree. Four subpopulations were selected using the following criteria for height growth and wood density: (i) fast growth and high density; (ii) slow growth and high density; (iii) fast growth and low density; and (iv) slow growth and low density. Significant differences were found among subpopulations for several anatomical parameters including tracheid density, lumen size, and cell wall thickness that may affect the economic value and utilization of wood. Principal component analysis indicate that the first four principal components (PCs) were associated with (i) ring area (PC1), (ii) earlywood density (PC2), (iii) latewood density (PC3), and (iv) lumen shape in earlywood (PC4), suggesting that these aspects of wood properties and growth are controlled by different sets of genes. Relative contributions of total number of tracheids, tracheid lumen size, and cell wall thickness to ring area and correlations between cell wall area proportion and X-ray density are discussed.

scholarly journals An Experimental Study on Mechanical Behavior of Parallel Joint Specimens under Compression Shear

2018 ◽  
Vol 2018 ◽  
pp. 1-12
Author(s):  
Fei Wang ◽  
Ping Cao ◽  
Yu Chen ◽  
Qing-peng Gao ◽  
Zhu Wang
Keyword(s):  
Shear Stress ◽  
Shear Strength ◽  
Failure Mode ◽  
Shear Failure ◽  
Strain Curve ◽  
Shear Loading ◽  
Plane Shear ◽  
Joint Spacing ◽  
Dip Angle ◽  
Joint Inclination

In order to investigate the influence of the joint on the failure mode, peak shear strength, and shear stress-strain curve of rock mass, the compression shear test loading on the parallel jointed specimens was carried out, and the acoustic emission system was used to monitor the loading process. The joint spacing and joint overlap were varied to alter the relative positions of parallel joints in geometry. Under compression-shear loading, the failure mode of the joint specimen can be classified into four types: coplanar shear failure, shear failure along the joint plane, shear failure along the shear stress plane, and similar integrity shear failure. The joint dip angle has a decisive effect on the failure mode of the specimen. The joint overlap affects the crack development of the specimen but does not change the failure mode of the specimen. The joint spacing can change the failure mode of the specimen. The shear strength of the specimen firstly increases and then decreases with the increase of the dip angle and reaches the maximum at 45°. The shear strength decreases with the increase of the joint overlap and increases with the increase of the joint spacing. The shear stress-displacement curves of different joint inclination samples have differences which mainly reflect in the postrupture stage. From monitoring results of the AE system, the variation regular of the AE count corresponds to the failure mode, and the peak value of the AE count decreases with the increase of joint overlap and increases with the increase of joint spacing.

Sign in / Sign up

Export Citation Format

Share Document