scholarly journals The Temperature Field Evolution and Water Migration Law of Coal under Low-Temperature Freezing Conditions

2021 ◽  
Vol 18 (24) ◽  
pp. 13188
Author(s):  
Bo Li ◽  
Li Li ◽  
Laisheng Huang ◽  
Xiaoquan Lv
Keyword(s):  
Temperature Field ◽  
Low Temperature ◽  
Temperature Gradient ◽  
Water Content ◽  
Freezing Process ◽  
Water Migration ◽  
Freezing Front ◽  
Coal Matrix ◽  
Matrix Potential ◽  
Segregation Potential

This study examines the evolution law of the coal temperature field under low-temperature freezing conditions. The temperature inside coal samples with different water contents was measured in real-time at several measurement points in different locations inside the sample under the condition of low-temperature medium (liquid nitrogen) freezing. The temperature change curve was then used to analyse the laws of temperature propagation and the movement of the freezing front of the coal, which revealed the mechanism of internal water migration in the coal under low-temperature freezing conditions. The results indicate that the greater the water content of the coal sample, the greater the temperature propagation rate. The reasons for this are the phase change of ice and water inside the coal during the freezing process; the increase in the contact area of the ice and coal matrix caused by the volume expansion; and the joint action of the two. The process of the movement of the freezing front is due to the greater adsorption force of the ice lens than that of the coal matrix. Thus, the water molecules adsorbed in the unfrozen area of the coal matrix migrate towards the freezing front and form a new ice lens. Considering the temperature gradient and water content of the coal samples, Darcy’s permeation equation and water migration equation for the inside of the coal under freezing conditions were derived, and the segregation potential and matrix potential were analysed. The obtained theoretical and experimental results were found to be consistent. The higher the water content of the coal samples, the smaller the matrix potential for the hindrance of water migration. Furthermore, the larger the temperature gradient, the larger the segregation potential, and the faster the water migration rate.

Multiple-fracturing and viewing of the same frozen sample at different depths using a low temperature FESEM

1996 ◽  
Vol 54 ◽  
pp. 820-821
Author(s):  
M.V. Parthasarathy ◽  
C. Daugherty
Keyword(s):  
Temperature Field ◽  
Low Temperature ◽  
Field Emission ◽  
Multiple Fracture ◽  
Precise Control ◽  
Cold Stage ◽  
Different Depths ◽  
Transfer Device

The versatility of Low Temperature Field Emission SEM (LTFESEM) for viewing frozen-hydrated biological specimens, and the high resolutions that can be obtained with such instruments have been well documented. Studies done with LTFESEM have been usually limited to the viewing of small organisms, organs, cells, and organelles, or viewing such specimens after fracturing them.We use a Hitachi 4500 FESEM equipped with a recently developed BAL-TEC SCE 020 cryopreparation/transfer device for our LTFESEM studies. The SCE 020 is similar in design to the older SCU 020 except that instead of having a dedicated stage, the SCE 020 has a detachable cold stage that mounts on to the FESEM stage when needed. Since the SCE 020 has a precisely controlled lock manipulator for transferring the specimen table from the cryopreparation chamber to the cold stage in the FESEM, and also has a motor driven microtome for precise control of specimen fracture, we have explored the feasibility of using the LTFESEM for multiple-fracture studies of the same sample.

scholarly journals Three-Dimensional Electro-Thermal Analysis of a New Type Current Transformer Design for Power Distribution Networks

Energies ◽  
2021 ◽  
Vol 14 (6) ◽  
pp. 1792
Author(s):  
Bingbing Dong ◽  
Yu Gu ◽  
Changsheng Gao ◽  
Zhu Zhang ◽  
Tao Wen ◽  
...  
Keyword(s):  
Boundary Condition ◽  
Temperature Field ◽  
Temperature Gradient ◽  
Field Distribution ◽  
Distribution Network ◽  
Current Transformer ◽  
Internal Temperature ◽  
Temperature Field Distribution ◽  
Type Design ◽  
New Type

In recent years, the new type design of current transformer with bushing structure has been widely used in the distribution network system due to its advantages of miniaturization, high mechanical strength, maintenance-free, safety and environmental protection. The internal temperature field distribution is an important characteristic parameter to characterize the thermal insulation and aging performance of the transformer, and the internal temperature field distribution is mainly derived from the joule heat generated by the primary side guide rod after flowing through the current. Since the electric environment is a transient field and the thermal environment changes slowly with time as a steady field under the actual conditions, it is more complex and necessary to study the electrothermal coupling field of current transformer (CT). In this paper, a 3D simulation model of a new type design of current transformer for distribution network based on electric-thermal coupling is established by using finite element method (FEM) software. Considering that the actual thermal conduction process of CT is mainly by conduction, convection and radiation, three different kinds of boundary conditions such as solid heat transfer boundary condition, heat convection boundary condition and surface radiation boundary condition are applied to the CT. Through the model created above, the temperature rise process and the distribution characteristics of temperature gradient of the inner conductor under different current, different ambient temperatures and different core diameters conditions are studied. Meanwhile, the hottest temperature and the maximum temperature gradient difference are calculated. According to this, the position of weak insulation of the transformer is determined. The research results can provide a reference for the factory production of new type design of current transformer.

Numerical Modeling and Simulation Analysis of Temperature Field of Disc Brake on Trains

2011 ◽  
Vol 199-200 ◽  
pp. 1492-1495 ◽  
Author(s):  
Guo Shun Wang ◽  
Rong Fu ◽  
Liang Zhao
Keyword(s):  
Temperature Field ◽  
Temperature Gradient ◽  
High Speed ◽  
Large Scale ◽  
Working Condition ◽  
Constant Speed ◽  
Brake Disc ◽  
Disc Brake ◽  
Brake Pad ◽  
Finite Element Software

The simulation calculation on the temperature field of the disc brake system on high-speed trains under the working condition of constant speed at 50Km/h is made. A steady-state calculation model is established according to the actual geometric size of a brake disc and a brake pad, and the analog calculation and simulation on the temperature field of the brake disc and the brake pad by using the large-scale nonlinear finite element software ABAQUS are carried out. The distribution rules of the temperature field of the brake disc and the brake pad under the working condition of constant speed are made known. The surface temperature of the brake disc at friction radius is the highest, with a band distribution for temperature. There exists a temperature flex point in the direction of thickness, of which the thickness occupies 15% of that of the brake disc; due to the small volume of the brake pad, the temperature gradient of the whole brake pad is not sharp, and larger temperature gradient occurs only on the contact surface.

Spin-Lattice Coupling and Peculiarities of Magnetic Behavior of Ferrimagnetic Ludwigites Mn0.52+M1.52+Mn3+BO5(M=Cu, Ni)

2015 ◽  
Vol 233-234 ◽  
pp. 133-136 ◽  
Author(s):  
Leonard Bezmaternykh ◽  
Evgeniya Moshkina ◽  
Evgeniy Eremin ◽  
Maxim Molokeev ◽  
Nikita Volkov ◽  
...  
Keyword(s):  
Temperature Field ◽  
Low Temperature ◽  
Magnetic Anisotropy ◽  
Single Crystals ◽  
Magnetic Behavior ◽  
Temperature Hysteresis ◽  
Spin Lattice ◽  
Field Magnetization ◽  
Lattice Coupling

Temperature-field and orientational magnetization dependences of single crystals were measured. Both samples demonstrate significant field-depending temperature hysteresis and low-temperature counter field magnetization. The correlation of orientational dependences of these effects and magnetic anisotropy is analyzed; the role of spin-lattice interactions is discussed.

scholarly journals Effect of temperature gradient on the cross-stream migration of a surfactant-laden droplet in Poiseuille flow

2017 ◽  
Vol 835 ◽  
pp. 170-216 ◽  
Author(s):  
Sayan Das ◽  
Shubhadeep Mandal ◽  
Suman Chakraborty
Keyword(s):  
Temperature Field ◽  
Temperature Gradient ◽  
Poiseuille Flow ◽  
Peclet Number ◽  
Marangoni Number ◽  
Stream Velocity ◽  
Small Surface ◽  
Péclet Number ◽  
Surfactant Transport ◽  
The Cross

The motion of a viscous droplet in unbounded Poiseuille flow under the combined influence of bulk-insoluble surfactant and linearly varying temperature field aligned in the direction of imposed flow is studied analytically. Neglecting fluid inertia, thermal convection and shape deformation, asymptotic analysis is performed to obtain the velocity of a force-free surfactant-laden droplet. The droplet speed and direction of motion are strongly influenced by the interfacial transport of surfactant, which is governed by surface Péclet number. The present study is focused on the following two limiting situations of surfactant transport: (i) surface-diffusion-dominated surfactant transport considering small surface Péclet number, and (ii) surface-convection-dominated surfactant transport considering high surface Péclet number. Thermocapillary-induced Marangoni stress, the strength of which relative to viscous stress is represented by the thermal Marangoni number, has a strong influence on the distribution of surfactant on the droplet surface. The present study shows that the motion of a surfactant-laden droplet in the combined presence of temperature and imposed Poiseuille flow cannot be obtained by a simple superposition of the following two independent results: migration of a surfactant-free droplet in a temperature gradient, and the motion of a surfactant-laden droplet in a Poiseuille flow. The temperature field not only affects the axial velocity of the droplet, but also has a non-trivial effect on the cross-stream velocity of the droplet in spite of the fact that the temperature gradient is aligned with the Poiseuille flow direction. When the imposed temperature increases in the direction of the Poiseuille flow, the droplet migrates towards the flow centreline. The magnitude of both axial and cross-stream velocity components increases with the thermal Marangoni number. However, when the imposed temperature decreases in the direction of the Poiseuille flow, the magnitude of both axial and cross-stream velocity components may increase or decrease with the thermal Marangoni number. Most interestingly, the droplet moves either towards the flow centreline or away from it. The present study shows a critical value of the thermal Marangoni number beyond which the droplet moves away from the flow centreline which is in sharp contrast to the motion of a surfactant-laden droplet in isothermal flow, for which the droplet always moves towards the flow centreline. Interestingly, we show that the above picture may become significantly altered in the case where the droplet is not a neutrally buoyant one. When the droplet is less dense than the suspending medium, the presence of gravity in the direction of the Poiseuille flow can lead to cross-stream motion of the droplet away from the flow centreline even when the temperature increases in the direction of the Poiseuille flow. These results may bear far-reaching consequences in various emulsification techniques in microfluidic devices, as well as in biomolecule synthesis, vesicle dynamics, single-cell analysis and nanoparticle synthesis.

3D Freeze Printing: Development of an Experimental Setup and Determination of 3D Printing Parameters

2020 ◽  
Author(s):  
Halil Tetik ◽  
Dong Lin
Keyword(s):  
3D Printing ◽  
Low Temperature ◽  
Temperature Gradient ◽  
Freeze Casting ◽  
Printing Process ◽  
Print Head ◽  
Freezing Temperatures ◽  
Fabrication Parameters ◽  
Printing Parameters

Abstract 3D freeze printing is a hybrid manufacturing method composed of freeze casting and inkjet-based printing. It is a facile method to fabricate lightweight, porous, and functional structures. Freeze casting is a well-known method for fabricating porous bodies and is capable of manipulating the micro-structure of the resulting product. Freeze casting simply involves solidification of a liquid suspension using low temperature and sublimation of the solvent using low temperature and pressure. After the sublimation of the solvent crystals, we obtain a porous structure where the pores are a replica of solvent crystal. Making use of the temperature gradient, as seen in unidirectional and bidirectional freeze casting, during the solidification with low temperature values, the solvent crystals grow along the temperature gradient. Furthermore, by manipulating the freezing kinetics during solidification, we can have a control on the average pore size distribution. For instance, when lower freezing temperatures result in finer pores with higher amount, higher freezing temperatures result in coarser pores with less amount. Also, the use of some additives inside the suspension leads to changes in the morphology of the solvent crystals as well as the resulting pores. However, the macro-structure of the fabricated body is highly dependent on the mold used during the process. In order to eliminate the dependency on the mold during the freeze casting process, our group recently combined this technique with inkjet-based 3D printing. With inkjet-based 3D printing, we fabricated uniform lines from single droplets, and complex 3D shapes from the lines. This provided us the ability of tailoring the macro structure of the final product without any dependency on a mold as seen in freeze casting. As a result of the 3D freeze printing process, we achieved fabricating lightweight, porous, and functional bodies with engineered micro and macro-structures. However, achieving fine droplets, and uniform lines by merging the droplets requires a good combination of fabrication parameters such as pressure adjustment inside the print head, print head speed, jetting frequency. Also, fabricating complex shapes from uniform lines requires well-adjusted parameters such as line thickness and layer height. In this study, we briefly explained the mechanics of the 3D freeze printing process. Following that we presented the development process of an open-source inkjet-based 3D printer. Finally, we explained the determination of inkjet dispensing and 3D printing parameters required for a high-quality 3D printing. During our experiments for the determination of fabrication parameters, we used a nanocellulose crystals-based ink due to its low cost and ease of preparation.

Numerical simulation of coupled liquid water, stress and heat for frozen soil in the thawing process

2021 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Wei Xiao ◽  
Enlong Liu ◽  
Xiao Yin ◽  
Guike Zhang ◽  
Chong Zhang ◽  
...  
Keyword(s):  
Numerical Simulation ◽  
Water Content ◽  
Coupled Model ◽  
Frozen Soil ◽  
Water Migration ◽  
Overburden Pressure ◽  
Content Type ◽  
Thawing Process ◽  
Sample Water ◽  
The One

PurposeThe purpose of this paper is to perform the thermo-hydro-mechanical (THM) numerical analysis in order to study the thawing process for frozen soil and to predict the thawing settlement.Design/methodology/approachA new one-dimensional multi-field physical coupled model was proposed here to describe the thawing process of saturated frozen soil, whereby the void ratio varied linearly with effective stress (Eq. 10) and hydraulic conductivity (Eq. 27b). The thawing process was simulated with different initial and boundary conditions in an open system with temperature variations. The mechanical behavior and water migration of the representative cases were also investigated.FindingsThe comparisons of representative cases with experimental data demonstrated that the model predicts thawing settlement well. It was found that the larger temperature gradient, higher overburden pressure and higher water content could lead to larger thawing settlement. The temperature was observed that to distribute height linearly in both frozen zone and unfrozen zone of the sample. Water migration forced to a decrease in the water content of the unfrozen zone and an increase in water content at the thawing front.Research limitations/implicationsIn this study, only the one-directional thawing processes along the frozen soil samples were investigated numerically and compared with test results, which can be extended to two-dimensional analysis of thawing process in frozen soil.Originality/valueThis study helps to understand the thawing process of frozen soil by coupled thermo-hydro-mechanical numerical simulation.

Sign in / Sign up

Export Citation Format

Share Document