scholarly journals Modeling of Drag Finishing—Influence of Abrasive Media Shape

2021 ◽  
Vol 5 (2) ◽  
pp. 41
Author(s):  
Irati Malkorra ◽  
Hanène Souli ◽  
Ferdinando Salvatore ◽  
Pedro Arrazola ◽  
Joel Rech ◽  
...  
Keyword(s):  
Surface Roughness ◽  
Material Removal ◽  
Direct Shear Test ◽  
Shear Test ◽  
Shear Resistance ◽  
Arbitrary Lagrangian Eulerian ◽  
Eulerian Model ◽  
Drag Forces ◽  
Drag Finishing ◽  
Surrounding Liquid

Drag finishing is a widely used superfinishing technique in the industry to polish parts under the action of abrasive media combined with an active surrounding liquid. However, the understanding of this process is not complete. It is known that pyramidal abrasive media are more prone to rapidly improving the surface roughness compared to spherical ones. Thus, this paper aims to model how the shape of abrasive media (spherical vs. pyramidal) influences the material removal mechanisms at the interface. An Arbitrary Lagrangian–Eulerian model of drag finishing is proposed with the purpose of estimating the mechanical loadings (normal stress, shear stress) induced by both abrasive media at the interface. The rheological behavior of both abrasive slurries (media and liquid) has been characterized by means of a Casagrande direct shear test. In parallel, experimental drag finishing tests were carried out with both media to quantify the drag forces. The correlation between the numerical and experimental drag forces highlights that the abrasive media with a pyramidal shape exhibits a higher shear resistance, and this is responsible for inducing higher mechanical loadings on the surfaces and, through this, for a faster decrease of the surface roughness.

Evaluating the Shear Resistance of Hot Mix Asphalt by the Direct Shear Test

2008 ◽  
Vol 36 (6) ◽  
pp. 101732 ◽  
Author(s):  
M. R. Mitchell ◽  
R. E. Link ◽  
Hai-nian Wang ◽  
Xi-jun Liu ◽  
Pei-wen Hao
Keyword(s):  
Direct Shear Test ◽  
Shear Test ◽  
Hot Mix Asphalt ◽  
Shear Resistance ◽  
Direct Shear

scholarly journals Analysis of Abrasives On Cutting Edge Preparation By Drag Finishing

2021 ◽  
Author(s):  
Dejin Lv ◽  
Yongguo Wang ◽  
Xin Yu ◽  
Han Chen ◽  
Yuan Gao
Keyword(s):  
Surface Roughness ◽  
Surface Topography ◽  
Material Removal ◽  
Cutting Edge ◽  
K Factor ◽  
Solid Carbide ◽  
End Mills ◽  
Cutting Edge Preparation ◽  
Drag Finishing ◽  
Edge Preparation

Abstract Cutting edge preparation has become more important for tool performance. The micro-shape, radius and surface topography of the cutting edge plays a significant role in the machining process. The cutting edge of solid carbide end mills have some micro-defects after grinding. For eliminating aforementioned problem, this study investigates drag finishing (DF) preparation for solid carbide end mills reconstruct cutting edge micro-geometry. This paper is to present the design of DF experimental set-up and analysis the characterization of various abrasive media (K3/600, K3/400, HSC 1/300 and HSO 1/100) on the evolution of the surface /roughness along the cutting edge. In parallel, the mechanism of material removal and the kinematics trajectory of the drag finishing are presented. In fact, the form factor (also called as “K-factor”) of the cutting edge micro-geometry is quantified. Comparing with four lapping media, the higher material removal rate (MRR) and the lower surface roughness are obtained by HSO 1/100 abrasive process. The results show that the cutting edge K-factor, MRR and surface topography are influenced by the abrasive particles size, composition and process time. The cutting edge micro-geometry is measured through Scanning Electron Microscopy (SEM) and 3D Optical measuring instrument.

A Study on Shear Strength of the Perfobond Rib Shear Connector for Composite Beam

2015 ◽  
Vol 764-765 ◽  
pp. 1026-1030
Author(s):  
Doo Yong Cho ◽  
Jin Woong Choi ◽  
Sun Kyu Park
Keyword(s):  
Shear Stress ◽  
Direct Shear Test ◽  
Shear Test ◽  
Shear Resistance ◽  
Shear Behavior ◽  
Shear Connector ◽  
Direct Shear ◽  
Mechanical Behaviors ◽  
Shear Connectors ◽  
Main Factors

For safe and efficient use of the Perfobond Rib shear connector, it is essential to investigate mechanical behaviors and evaluate performance of shear resistance. When the Perforbond Rib shear connectors are to be used for a structure, they show flexural-shear behavior due to external force rather than direct shear behavior. Therefore, this study performed a direct shear test and proposed the equation for the shear resistance assessment. Also, a flexural shear test was conducted. Through the direct shear test, main factors that affect directly shear resistance were found. The flexural shear stress and the direct shear stress were calculated and it is revealed that the flexural shear stress is approximately 6% stronger than the direct shear stress.

Effects of Process Parameters on Surface Roughness and MRR in the hard turning of EN 36 steel

2018 ◽  
pp. 102-110
Author(s):  
Amritpal Singh ◽  
Rakesh Kumar
Keyword(s):  
Surface Roughness ◽  
Material Removal Rate ◽  
Material Removal ◽  
Hard Turning ◽  
Control Parameter ◽  
Removal Rate ◽  
Cutting Speed ◽  
Depth Of Cut ◽  
Cutting Condition ◽  
Dry Cutting

In the present study, Experimental investigation of the effects of various cutting parameters on the response parameters in the hard turning of EN36 steel under the dry cutting condition is done. The input control parameters selected for the present work was the cutting speed, feed and depth of cut. The objective of the present work is to minimize the surface roughness to obtain better surface finish and maximization of material removal rate for better productivity. The design of experiments was done with the help of Taguchi L9 orthogonal array. Analysis of variance (ANOVA) was used to find out the significance of the input parameters on the response parameters. Percentage contribution for each control parameter was calculated using ANOVA with 95 % confidence value. From results, it was observed that feed is the most significant factor for surface roughness and the depth of cut is the most significant control parameter for Material removal rate.

Effect of SiC-Cu Electrode on Material Removal Rate, Tool Wear and Surface Roughness in EDM Process

2020 ◽  
Vol 38 (9A) ◽  
pp. 1406-1413
Author(s):  
Yousif Q. Laibia ◽  
Saad K. Shather
Keyword(s):  
Surface Roughness ◽  
Tool Wear ◽  
Material Removal Rate ◽  
Material Removal ◽  
Electrical Discharge Machining ◽  
Removal Rate ◽  
304 Stainless Steel ◽  
Tool Electrode ◽  
Pulse Time ◽  
Edm Process

Electrical discharge machining (EDM) is one of the most common non-traditional processes for the manufacture of high precision parts and complex shapes. The EDM process depends on the heat energy between the work material and the tool electrode. This study focused on the material removal rate (MRR), the surface roughness, and tool wear in a 304 stainless steel EDM. The composite electrode consisted of copper (Cu) and silicon carbide (SiC). The current effects imposed on the working material, as well as the pulses that change over time during the experiment. When the current used is (8, 5, 3, 2, 1.5) A, the pulse time used is (12, 25) μs and the size of the space used is (1) mm. Optimum surface roughness under a current of 1.5 A and the pulse time of 25 μs with a maximum MRR of 8 A and the pulse duration of 25 μs.

Enhancement of EDM Performance by Using Copper-Silver Composite Electrode

2020 ◽  
Vol 38 (9A) ◽  
pp. 1352-1358
Author(s):  
Saad K. Shather ◽  
Abbas A. Ibrahim ◽  
Zainab H. Mohsein ◽  
Omar H. Hassoon
Keyword(s):  
Surface Roughness ◽  
Material Removal Rate ◽  
Material Removal ◽  
High Speed ◽  
Composite Electrode ◽  
Removal Rate ◽  
Pure Copper ◽  
High Speed Steel ◽  
Pulse On Time ◽  
Pulse Off Time

Discharge Machining is a non-traditional machining technique and usually applied for hard metals and complex shapes that difficult to machining in the traditional cutting process. This process depends on different parameters that can affect the material removal rate and surface roughness. The electrode material is one of the important parameters in Electro –Discharge Machining (EDM). In this paper, the experimental work carried out by using a composite material electrode and the workpiece material from a high-speed steel plate. The cutting conditions: current (10 Amps, 12 Amps, 14 Amps), pulse on time (100 µs, 150 µs, 200 µs), pulse off time 25 µs, casting technique has been carried out to prepare the composite electrodes copper-sliver. The experimental results showed that Copper-Sliver (weight ratio70:30) gives better results than commonly electrode copper, Material Removal Rate (MRR) Copper-Sliver composite electrode reach to 0.225 gm/min higher than the pure Copper electrode. The lower value of the tool wear rate achieved with the composite electrode is 0.0001 gm/min. The surface roughness of the workpiece improved with a composite electrode compared with the pure electrode.

scholarly journals Effect of Water-Based Nanolubricants in Ultrasonic Vibration Assisted Grinding

2018 ◽  
Vol 2 (4) ◽  
pp. 80 ◽  
Author(s):  
Mir Molaie ◽  
Ali Zahedi ◽  
Javad Akbari
Keyword(s):  
Surface Roughness ◽  
Specific Energy ◽  
Material Removal ◽  
Normal Force ◽  
Tangential Force ◽  
Process Efficiency ◽  
Multiwall Carbon Nanotube ◽  
Ultrasonic Vibrations ◽  
Mql Grinding ◽  
Water Based

Currently, because of stricter environmental standards and highly competitive markets, machining operations, as the main part of the manufacturing cycle, need to be rigorously optimized. In order to simultaneously maximize the production quality and minimize the environmental issues related to the grinding process, this research study evaluates the performance of minimum quantity lubrication (MQL) grinding using water-based nanofluids in the presence of horizontal ultrasonic vibrations (UV). In spite of the positive impacts of MQL using nanofluids and UV which are extensively reported in the literature, there is only a handful of studies on concurrent utilization of these two techniques. To this end, for this paper, five kinds of water-based nanofluids including multiwall carbon nanotube (MWCNT), graphite, Al2O3, graphene oxide (GO) nanoparticles, and hybrid Al2O3/graphite were employed as MQL coolants, and the workpiece was oscillated along the feed direction with 21.9 kHz frequency and 10 µm amplitude. Machining forces, specific energy, and surface quality were measured for determining the process efficiency. As specified by experimental results, the variation in the material removal nature made by ultrasonic vibrations resulted in a drastic reduction of the grinding normal force and surface roughness. In addition, the type of nanoparticles dispersed in water had a strong effect on the grinding tangential force. Hybrid Al2O3/graphite nanofluid through two different kinds of lubrication mechanisms—third body and slider layers—generated better lubrication than the other coolants, thereby having the lowest grinding forces and specific energy (40.13 J/mm3). It was also found that chemically exfoliating the graphene layers via oxidation and then purification prior to dispersion in water promoted their effectiveness. In conclusion, UV assisted MQL grinding increases operation efficiency by facilitating the material removal and reducing the use of coolants, frictional losses, and energy consumption in the grinding zone. Improvements up to 52%, 47%, and 61%, respectively, can be achieved in grinding normal force, specific energy, and surface roughness compared with conventional dry grinding.

High-Throughput Picosecond Laser Machining of Aerospace Nickel Superalloy

2021 ◽  
pp. 095440542110288
Author(s):  
Sundar Marimuthu ◽  
Bethan Smith
Keyword(s):  
Surface Roughness ◽  
Material Removal Rate ◽  
Material Removal ◽  
Thermal Damage ◽  
Removal Rate ◽  
Picosecond Laser ◽  
Nickel Superalloy ◽  
Laser Machining ◽  
Process Conditions ◽  
Machining Performance

This manuscript discusses the experimental results on 300 W picosecond laser machining of aerospace-grade nickel superalloy. The effect of the laser’s energetic and beam scanning parameters on the machining performance has been studied in detail. The machining performance has been investigated in terms of surface roughness, sub-surface thermal damage, and material removal rate. At optimal process conditions, a picosecond laser with an average power output of 300 W can be used to achieve a material removal rate (MRR) of ∼140 mm3/min, with thermal damage less than 20 µm. Shorter laser pulse widths increase the material removal rate and reduce the resultant surface roughness. High scanning speeds improve the picosecond laser machining performance. Edge wall taper of ∼10° was observed over all the picosecond laser machined slots. The investigation demonstrates that high-power picosecond lasers can be used for the macro-machining of industrial components at an acceptable speed and quality.

Sign in / Sign up

Export Citation Format

Share Document