scholarly journals The Study on Mechanical Strength of Titanium-Aluminum Dissimilar Butt Joints by Laser Welding-Brazing Process

Materials ◽  
2019 ◽  
Vol 12 (5) ◽  
pp. 712 ◽  
Author(s):  
Xiongfeng Zhou ◽  
Ji’an Duan ◽  
Fan Zhang ◽  
Shunshun Zhong
Keyword(s):  
Tensile Strength ◽  
Laser Welding ◽  
Welding Speed ◽  
Laser Power ◽  
Butt Joint ◽  
Interface Fracture ◽  
Welding Parameters ◽  
Fracture Roughness ◽  
Joint Properties ◽  
5A06 Aluminum Alloy

Laser welding–brazing of 5A06 aluminum to Ti6Al4V titanium in a butt configuration was carried out to discuss the influences of welding parameters on dissimilar joint properties. The effects of laser offset, welding speed, and laser power on the spreading length of the molten aluminum liquid, interface fracture zone width (IFZW), fracture roughness, intermetallic compounds (IMCs) thickness, and tensile strength were also investigated. The microstructure and fracture of the joint were also studied. The results show that the tensile strength of the joint is not only influenced by the thickness and type of IMCs, but also influenced by the spreading ability of the aluminum liquid, the fracture area broken at the Ti/fusing zone (FZ) interface, and the relative area of the brittle and ductile fracture in FZ. A dissimilar butt joint with an IMC thickness of 2.79 μm was obtained by adjusting the laser offset, welding speed, and laser power to 500 μm, 11 mm/s and 1130 W, respectively. The maximum tensile strength of the joint was up to 183 MPa, which is equivalent to 83% of the tensile strength of the 5A06 aluminum alloy.

scholarly journals An Investigation on Laser Welding Parameters on the Strength of TRIP Steel

2021 ◽  
Vol 67 (1-2) ◽  
pp. 45-52
Author(s):  
S Khot Rahul ◽  
T Venkateshwara Rao ◽  
Natu Harshad ◽  
H N Girish ◽  
Tadashi Ishigaki ◽  
...  
Keyword(s):  
Tensile Strength ◽  
Laser Welding ◽  
High Power ◽  
Heat Affected Zone ◽  
Trip Steel ◽  
Arc Welding ◽  
Laser Power ◽  
Welded Joint ◽  
Incident Angle ◽  
Welding Parameters

The energy required for joining steel segments by using laser welding is relatively very low compared with arc welding, gas welding, or any other conventional welding techniques. Moreover, the rapid cooling may create a significant effect on different regions, such as the fusion zone (FZ), heat affected zone (HAZ), and base metal (BM), and in turn affect different parameters. In this study, the characteristics of the laser-welded joint were investigated by varying laser power, welding velocity and incident angle, and tensile strength. In our, experiments. the microhardness was increased by varying the power of laser welding. The strength of the joint was increased to 549 MPa with 2200 W high power, 30 mm/s velocity, and 80º laser incident angle. By increasing the power and velocity of the laser, the welding gun strength was improved; conversely, the angle of laser incident on the welding location decreased while its strength was increased.

Optimization of Laser Welding Parameters in Aluminum Alloy Welding and Development of Quality Monitoring System for Light Weight Vehicle

2012 ◽  
Vol 706-709 ◽  
pp. 2998-3003 ◽  
Author(s):  
Young Whan Park ◽  
Dong Yun Kim
Keyword(s):  
Tensile Strength ◽  
Aluminum Alloy ◽  
Laser Welding ◽  
Monitoring System ◽  
Welding Speed ◽  
Feed Rate ◽  
Laser Power ◽  
Filler Wire ◽  
Weld Quality ◽  
Wire Feed

In this paper laser welding AA5182 of aluminum alloy with AA5356 filler wire were performed with respect to laser power, welding speed, and wire feed rate. The experiments showed that the tensile strength of the weld was higher than that of the base material under sufficient heat input conditions. A genetic algorithm was used to optimize process parameters which were the laser power, welding speed, and wire feed rate. To do that, a fitness function was formulated, taking into account weldability and productivity. A factor for the weldabilty used tensile strength estimation model which was made by neural network, and as the productivity, welding speed, and wire feed rate were used. Weld monitoring system for aluminum laser welding with filler wire was constructed through the optical sensors to measure the plasma light intensity. Relationship between monitoring signal and plasma and keyhole behavior according to welding condition was analyzed and it was found that sensor signal could express the information for weld quality. Weld quality estimation algorithm was formulated fuzzy multi feature pattern recognition algorithm using the monitoring signals. Quality prediction system was also developed to apply this algorithm to production line.

scholarly journals Numerical Simulation of Laser Welding Dissimilar Low Carbon and Austenitic Steel Joint

2020 ◽  
Vol 10 (1) ◽  
pp. 491-498
Author(s):  
Hubert Danielewski ◽  
Andrzej Skrzypczyk ◽  
Szymon Tofil ◽  
Grzegorz Witkowski ◽  
Sławomir Rutkowski
Keyword(s):  
Numerical Simulation ◽  
Heat Source ◽  
Laser Welding ◽  
Fusion Zone ◽  
Welding Process ◽  
Butt Joint ◽  
Austenitic Steels ◽  
Welding Parameters ◽  
Low Carbon ◽  
Joint Properties

AbstractNumerical simulation of laser welding dissimilar joint was presented. Results of butt joint for low carbon and austenitic steels are studied. Numerical calculations based on thermo-mechanical method and phase transformation were used for estimating weld dimensions and joint properties. Unconventional welding method where focused photons beam are used as a heat source were presented. Problems with welding of dissimilar joints, where different composition and thermo physical material properties affect on this phenomena complexity are solved using numerical methods and laser welding technology. Simulation of low carbon and stainless steel joints using SimufactWelding software are presented. Model of heat source within geometry and parameters was programmed. Laser beam welding simulation was performed for estimating parameters for complete joints penetration. Programming welding boundary condition and heat source geometry welding parameters with output power and welding speed rate was estimated. Materials used in simulation process and experimental welding was low carbon construction S235JR and stainless 316L steels in sheets form. Joint properties such as fusion zone and heat affected zones dimensions and stress-strain distribution were calculated. Estimation of complete joint characteristics was obtained using thermo-mechanical simulation method and Marc solver engine.. Experimental trial butt joint welding were performed based on estimated parameters. Welding process was performed using 6kW CO2 laser system. Based on numerical simulation, microstructure analysis, hardness distribution and chemical distribution of fusion zone, properties of obtained joint was studied. Model for simulation of dissimilar laser welding joint was obtained, and properties of obtained joint based on simulation and experiment was studied.

Fiber Laser Welding of Noncombustible Magnesium Alloy

2008 ◽  
Vol 580-582 ◽  
pp. 479-482 ◽  
Author(s):  
Yuji Sakai ◽  
Kazuhiro Nakata ◽  
Takuya Tsumura ◽  
Mitsuji Ueda ◽  
Tomoyuki Ueyama ◽  
...  
Keyword(s):  
Tensile Strength ◽  
Magnesium Alloy ◽  
Laser Welding ◽  
Fiber Laser ◽  
Vickers Hardness ◽  
Laser Power ◽  
Welded Joint ◽  
Welding Process ◽  
Fiber Laser Welding ◽  
Laser Welding Process

Noncombustible magnesium alloy AMC602 (Mg-6mass%Al-2mass%Ca) extruded sheet of 2.0mm thickness was successfully welded using a fiber laser welding process at welding speed of 10m/min at 3kW laser power. Tensile strength of the welded joint was about 82 to 88% of that of the base metal. Vickers hardness, tensile strength and micro structural properties are also discussed.

scholarly journals Study of Laser Welding of HCT600X Dual Phase Steels

2014 ◽  
Vol 22 (1) ◽  
pp. 93-98
Author(s):  
Pavol Švec ◽  
Viliam Hrnčiar ◽  
Alexander Schrek
Keyword(s):  
Tensile Strength ◽  
Base Metal ◽  
Heat Affected Zone ◽  
Welding Speed ◽  
Welding Process ◽  
Beam Power ◽  
Welding Parameters ◽  
Dual Phase ◽  
Welded Steel ◽  
Steel Sheets

AbstractThe effects of beam power and welding speed on microstructure, microhardnes and tensile strength of HCT600X laser welded steel sheets were evaluated. The welding parameters influenced both the width and the microstructure of the fusion zone and heat affected zone. The welding process has no effect on tensile strength of joints which achieved the strength of base metal and all joints fractured in the base metal.

Numerical Analysis of Solidification Behavior during Laser Welding Nickel-Based Single-Crystal Superalloy Part: II Crystallography-Dependent Supersaturation of Liquid Aluminum

2021 ◽  
Vol 1018 ◽  
pp. 13-22
Author(s):  
Zhi Guo Gao
Keyword(s):  
Laser Welding ◽  
Single Crystal ◽  
Weld Pool ◽  
Welding Speed ◽  
Heat Input ◽  
Laser Power ◽  
Liquid Aluminum ◽  
Dendrite Growth ◽  
Solidification Cracking ◽  
Solid Liquid Interface

The thermal metallurgical modeling of liquid aluminum supersaturation was further developed through couple of heat transfer model, dendrite selection model, multicomponent dendrite growth model and nonequilibrium solidification model during three-dimensional nickel-based single-crystal superalloy weld pool solidification. The welding configuration plays more important role in supersaturation of liquid aluminum, morphology instability and nonequilibrium partition behavior. The bimodal distribution of liquid aluminum supersaturation along the solid/liquid interface is crystallographically symmetrical about the weld pool centerline in (001) and [100] welding configuration. The distribution of liquid aluminum supersaturation along the solid/liquid interface is crystallographically asymmetrical throughout the weld pool in (001) and [110] welding configuration. Optimum low heat input (low laser power and high welding speed) with (001) and [100] welding configuration is more favored to predominantly promote epitaxial [001] dendrite growth to reduce the metallurgical factors for solidification cracking than that of high heat input (high laser power and slow welding speed) with (001) and [110] welding configuration. The lower the heat input is used, the lower supersaturation of liquid aluminum is imposed, and the smaller size of vulnerable [100] dendrite growth region is incurred to ameliorate solidification cracking susceptibility and vice versa. The overall supersaturation of liquid aluminum in (001) and [100] welding configuration is beneficially smaller than that of (001) and [110] welding configuration regardless of heat input, and is not thermodynamically relieved by gamma prime γˊ phase. (001) and [110] welding configuration is detrimental to weldability and deteriorates the solidification cracking susceptibility because of unfavorable crystallographic orientations and alloying aluminum enrichment. The mechanism of asymmetrical solidification cracking because of crystallography-dependent supersaturation of liquid aluminum is proposed. The eligible solidification cracking location is particularly confined in [100] dendrite growth region. Moreover, the theoretical predictions agree well with the experiment results. The useful modeling is also applicable to other single-crystal superalloys with similar metallurgical properties for laser welding or laser cladding. The thorough numerical analyses facilitate the understanding of weld pool solidification behavior, microstructure development and solidification cracking phenomena in the primary γ phase, and thereby optimize the welding conditions (laser power, welding speed and welding configuration) for successful crack-free laser welding.

Modeling of Weld Lap-Shear Strength for Laser Transmission Welding of Thermoplastic Using Artificial Neural Network

2012 ◽  
Vol 445 ◽  
pp. 454-459 ◽  
Author(s):  
M.R. Nakhaei ◽  
N.B. Mostafa Arab ◽  
F. Kordestani
Keyword(s):  
Neural Network ◽  
Artificial Neural Network ◽  
Shear Strength ◽  
Laser Welding ◽  
Process Parameters ◽  
Welding Speed ◽  
Laser Power ◽  
Laser Transmission Welding ◽  
Lap Shear Strength ◽  
Lap Shear

Laser welding of plastic materials has a wide range of applications in the packaging, medical, electronics and automobile industries provided it can predict high quality welds compared with other joining methods. Laser welding process parameters can affect the quality of welds. In this paper, Artificial Neural Network (ANN) is used to model the effects of laser power, welding speed, clamp pressure and stand-off distance on weld lap-shear strength in laser transmission welding (LTW) of acrylic (polymathy methacrylate). A set of experimental data on diode laser weld lap-shear strengths was used to train and test the ANN from which the neurons relations were gradually extracted to develop a model. The developed ANN model can be used for the analysis and prediction of the complex relationships between the above mentioned process parameters and weld lap-shear strength. The results indicated that increase in laser power and clamp pressure increases the weld lap-shear strength whereas welding speed and stand off distance had a decreasing affect on shear strength at high value.

A Parametric Study on Laser Welding of Magnesium Alloy AZ31 by a Fiber Laser

2014 ◽  
Author(s):  
Neil S. Bailey ◽  
Wenda Tan ◽  
Yung C. Shin
Keyword(s):  
Magnesium Alloy ◽  
Laser Welding ◽  
Fiber Laser ◽  
Welding Speed ◽  
Laser Power ◽  
Alloy Az31 ◽  
Magnesium Alloy Az31 ◽  
Wrought Magnesium Alloy ◽  
Weld Pool Geometry ◽  
Good Agreement

Laser welding of wrought magnesium alloy has been investigated through experimentation and simulation. Laser butt welds and laser lap welds were performed on 2.0 mm thick magnesium alloy AZ31 plates using a 1 kW fiber laser and shielded with argon gas. The effects of laser power and welding speed on weld geometry and microstructure were investigated. Through experimentation, the ranges of operating parameters for laser power and welding speed which resulted in viable, defect-free welds were found and reported. Simulations were carried out to predict the weld pool geometry and resultant microstructure and are shown to be in good agreement with experimental results.

Quality Assessment and Metallurgical Examination of Laser Welded Sheets

2009 ◽  
Vol 83-86 ◽  
pp. 611-615
Author(s):  
Numan Abu-Dheir ◽  
Bekir Sami Yilbas
Keyword(s):  
Laser Welding ◽  
Laser Power ◽  
Laser Scanning ◽  
Scanning Speed ◽  
Careful Examination ◽  
Welding Parameters ◽  
Weld Quality ◽  
Laser Weld ◽  
Power Intensity ◽  
Segregation Profile

Laser welding of steel 316L sheets is considered and the effects of laser welding parameters on the laser weld quality and metallurgical changes in the weld section are presented. The laser weld quality is assessed through careful examination of weld geometrical features, and the resulting weld microstructure. Metallurgical changes in the weld sites are examined using optical, and electron scanning microscope (SEM). Two levels of heat inputs are used-1500W and 2000W; and two scanning speeds of 2cm/s and 4cm/s are used to laser weld 316L sheets. It is found that at the high laser power intensities, evaporation takes place in the irradiated region and as the laser power intensity increases further, a cavity is formed at the top surface of the welding cross section. A similar situation is also observed as the laser scanning speed reduces. The low diffusivity of the alloying elements at high temperatures preserves the segregation profile. The scattered partitioning of the cells and dendrite boundaries are observed due to the presence of Cr and Mo.

A Parametric Study on Laser Welding of Magnesium Alloy AZ31 by a Fiber Laser

2015 ◽  
Vol 137 (4) ◽  
Author(s):  
Neil S. Bailey ◽  
Wenda Tan ◽  
Yung C. Shin
Keyword(s):  
Magnesium Alloy ◽  
Laser Welding ◽  
Fiber Laser ◽  
Welding Speed ◽  
Laser Power ◽  
Tensile Tests ◽  
Alloy Az31 ◽  
Magnesium Alloy Az31 ◽  
Weld Pool Geometry ◽  
Novel Processing

Laser welding of wrought magnesium alloy has been investigated through experimentation and simulation. Laser butt welds and laser lap welds were performed on 2.0 mm thick magnesium alloy AZ31 plates using a 1 kW fiber laser and shielded with argon gas. The effects of laser power and welding speed on weld geometry and microstructure were investigated. Tensile tests were performed to verify weld quality. Through experimentation, a novel processing map was created, which gives the ranges of operating parameters of laser power and welding speed that resulted in viable, defect-free welds. Numerical simulations were performed to predict the weld pool geometry and keyhole stability, and resultant microstructures are shown to be in good agreement with experimental results.

Sign in / Sign up

Export Citation Format

Share Document