scholarly journals Influence of Process Parameters on the Porosity, Accuracy, Roughness, and Support Structures of Hastelloy X Produced by Laser Powder Bed Fusion

Materials ◽  
2019 ◽  
Vol 12 (19) ◽  
pp. 3178 ◽  
Author(s):  
Calignano ◽  
Minetola
Keyword(s):  
Surface Roughness ◽  
Thermal Stresses ◽  
Production Costs ◽  
Powder Bed Fusion ◽  
Support Structures ◽  
Laser Powder Bed Fusion ◽  
Influence Of Process Parameters ◽  
Hastelloy X ◽  
Lower Face ◽  
Powder Bed

The manufacture of highly complex components from nickel-based superalloys with laser powder bed fusion (L-PBF) technology can reduce the production costs parts with comparable microstructural and mechanical properties when compared to casting. The purpose of this study was to investigate the characteristics of samples produced in commercial Hastelloy X (with w% composition of 21Cr-18Fe-9Mo-0.7W-1.5Co-0.1C-1Si-1Mn-0.5Al-0.15Ti-bal.Ni) with an L-PBF process in terms of build density, accuracy, surface roughness, and interface area between the part and the support structures. Samples were obtained with a high density (99.88%), without cracks and with low surface roughness. From the analysis of the support structures, it emerged that the choice of the parameters between support structures, the lower face of the part (down-skin) and the internal area of the part (in-skin) is fundamental to the correct realization of these structures in order to avoid deformation of the components that is induced by thermal stresses during part building.

scholarly journals On the Relevance of Volumetric Energy Density in the Investigation of Inconel 718 Laser Powder Bed Fusion

Materials ◽  
2020 ◽  
Vol 13 (3) ◽  
pp. 538 ◽  
Author(s):  
Fabrizia Caiazzo ◽  
Vittorio Alfieri ◽  
Giuseppe Casalino
Keyword(s):  
Surface Roughness ◽  
Energy Density ◽  
Process Parameters ◽  
Vickers Hardness ◽  
Powder Bed Fusion ◽  
Processing Conditions ◽  
Laser Powder Bed Fusion ◽  
Powder Bed ◽  
Fractional Density ◽  
Experimental Variation

Laser powder bed fusion (LPBF) can fabricate products with tailored mechanical and surface properties. In fact, surface texture, roughness, pore size, the resulting fractional density, and microhardness highly depend on the processing conditions, which are very difficult to deal with. Therefore, this paper aims at investigating the relevance of the volumetric energy density (VED) that is a concise index of some governing factors with a potential operational use. This paper proves the fact that the observed experimental variation in the surface roughness, number and size of pores, the fractional density, and Vickers hardness can be explained in terms of VED that can help the investigator in dealing with several process parameters at once.

Camera signal dependencies within coaxial melt pool monitoring in laser powder bed fusion

2020 ◽  
Vol 26 (1) ◽  
pp. 100-106 ◽  
Author(s):  
Tobias Kolb ◽  
Reza Elahi ◽  
Jan Seeger ◽  
Mathews Soris ◽  
Christian Scheitler ◽  
...  
Keyword(s):  
Surface Roughness ◽  
Layer Thickness ◽  
Powder Layer ◽  
Powder Bed Fusion ◽  
Laser Powder Bed Fusion ◽  
Content Type ◽  
Powder Bed ◽  
Sensory Signals ◽  
Melt Pool ◽  
Research Activities

Purpose The purpose of this paper is to analyse the signal dependency of the camera-based coaxial monitoring system QMMeltpool 3D (Concept Laser GmbH, Lichtenfels, Germany) for laser powder bed fusion (LPBF) under the variation of process parameters, position, direction and layer thickness to determine the capability of the system. Because such and similar monitoring systems are designed and presented for quality assurance in series production, it is important to present the dominant signal influences and limitations. Design/methodology/approach Hardware of the commercially available coaxial monitoring QMMeltpool 3D is used to investigate the thermal emission of the interaction zone during LPBF. The raw images of the camera are analysed by means of image processing to bypass the software of QMMeltpool 3D and to gain a high level of signal understanding. Laser power, scan speed, laser spot diameter and powder layer thickness were varied for single-melt tracks to determine the influence of a parameter variation on the measured sensory signals. The effects of the scan direction and position were also analysed in detail. The influence of surface roughness on the detected sensory signals was simulated by a machined substrate plate. Findings Parameter variations are confirmed to be detectable. Because of strong directional and positional dependencies of the melt-pool monitoring signal a calibration algorithm is necessary. A decreasing signal is detected for increasing layer thickness. Surface roughness is identified as a dominating factor with major influence on the melt-pool monitoring signal exceeding other process flaws. Research limitations/implications This work was performed with the hardware of a commercially available QMMeltpool 3D system of an LPBF machine M2 of the company Concept Laser GmbH. The results are relevant for all melt-pool monitoring research activities connected to LPBF, as well as for end users and serial production. Originality/value Surface roughness has not yet been revealed as being one of the most important origins for signal deviations in coaxial melt-pool monitoring. To the best of the authors’ knowledge, the direct comparison of influences because of parameters and environment has not been published to this extent. The detection, evaluation and remelting of surface roughness constitute a plausible workflow for closed-loop control in LPBF.

Realistic design of laser powder bed fusion channels

2020 ◽  
Vol 26 (10) ◽  
pp. 1827-1836
Author(s):  
Christopher Gottlieb Klingaa ◽  
Sankhya Mohanty ◽  
Jesper Henri Hattel
Keyword(s):  
Surface Roughness ◽  
Prediction Models ◽  
Powder Bed Fusion ◽  
Laser Powder Bed Fusion ◽  
Channel Design ◽  
Conformal Cooling ◽  
Content Type ◽  
Powder Bed ◽  
Cooling Channels ◽  
Conformal Cooling Channels

Purpose Conformal cooling channels in additively manufactured molds are superior over conventional channels in terms of cooling control, part warpage and lead time. The heat transfer ability of cooling channels is determined by their geometry and surface roughness. Laser powder bed fusion manufactured channels have an inherent process-induced dross formation that may significantly alter the actual shape of nominal channels. Therefore, it is crucial to be able to predict the expected surface roughness and changes in the geometry of metal additively manufactured conformal cooling channels. The purpose of this paper is to present a new methodology for predicting the realistic design of laser powder bed fusion channels. Design/methodology/approach This study proposes a methodology for making nominal channel design more realistic by the implementation of roughness prediction models. The models are used for altering the nominal shape of a channel to its predicted shape by point cloud analysis and manipulation. Findings A straight channel is investigated as a simple case study and validated against X-ray computed tomography measurements. The modified channel geometry is reconstructed and meshed, resulting in a predicted, more realistic version of the nominal geometry. The methodology is successfully tested on a torus shape and a simple conformal cooling channel design. Finally, the methodology is validated through a cooling test experiment and comparison with simulations. Practical implications Accurate prediction of channel surface roughness and geometry would lead toward more accurate modeling of cooling performance. Originality/value A robust start to finish method for realistic geometrical prediction of metal additive manufacturing cooling channels has yet to be proposed. The current study seeks to fill the gap.

scholarly journals Control of Crystallographic Texture and Mechanical Properties of Hastelloy-X via Laser Powder Bed Fusion

Crystals ◽  
2021 ◽  
Vol 11 (9) ◽  
pp. 1064
Author(s):  
Shinya Hibino ◽  
Tsubasa Todo ◽  
Takuya Ishimoto ◽  
Ozkan Gokcekaya ◽  
Yuichiro Koizumi ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Process Parameters ◽  
Crystallographic Texture ◽  
Lamellar Microstructure ◽  
Powder Bed Fusion ◽  
Laser Powder Bed Fusion ◽  
Hastelloy X ◽  
Single Crystalline ◽  
Powder Bed ◽  
Wide Range

The influence of various laser powder bed fusion (LPBF) process parameters on the crystallographic textures and mechanical properties of a typical Ni-based solid-solution strengthened alloy, Hastelloy-X, was examined. Samples were classified into four groups based on the type of crystallographic texture: single crystalline-like microstructure with <100>//build direction (BD) (<100>-SCM), single crystalline-like microstructure with <110>//BD (<110>-SCM), crystallographic lamellar microstructure (CLM), or polycrystalline microstructure (PCM). These four crystallographic textures were realized in Hastelloy-X for the first time here to the best of our knowledge. The mechanical properties of the samples varied depending on their texture. The tensile properties were affected not only by the Schmid factor but also by the grain size and the presence of lamellar boundaries (grain boundaries). The lamellar boundaries at the interface between the <110>//BD oriented main layers and the <100>//BD-oriented sub-layers of CLM contributed to the resistance to slip transmission and the increased proof stress. It was possible to control a wide range of crystallographic microstructures via the LPBF process parameters, which determines the melt pool morphology and solidification behavior.

scholarly journals Characterization of additively manufactured AlSilOMg cubes with different porosities

2021 ◽  
Vol 121 (4) ◽  
Author(s):  
C. Taute ◽  
H. Möller ◽  
A. du Plessis ◽  
M. Tshibalanganda ◽  
M. Leary
Keyword(s):  
Surface Roughness ◽  
Additive Manufacturing ◽  
Structural Integrity ◽  
Lead Times ◽  
Powder Bed Fusion ◽  
Laser Powder Bed Fusion ◽  
Powder Bed ◽  
Sample Characteristics

SYNOPSIS Additive manufacturing can be used to produce complex and custom geometries, consolidating different parts into one, which in turn reduces the required number of assemblies and allows distributed manufacturing with short lead times. Defects, such as porosity and surface roughness, associated with parts manufactured by laser powder bed fusion, can severely limit industrial application. The effect these defects have on corrosion and hence long-term structural integrity must also be taken into consideration. The aim of this paper is to report on the characterization of porosity in samples produced by laser powder bed fusion, with the differences in porosity induced by changes in the process parameters. The alloy used in this investigation is AlSi10Mg, which is widely used in the aerospace and automotive industries. The sample characteristics, obtained by X-ray tomography, are reported. The design and production of additively manufactured parts can be improved when these defects are better understood. Keywords: additive manufacturing, L-PBF, AlSi10Mg, porosity, surface roughness, density.

scholarly journals In Situ Thermography During Laser Powder Bed Fusion of a Nickel Superalloy 625 Artifact with Various Overhangs and Supports

2021 ◽  
Vol 126 ◽  
Author(s):  
Benjamin Molnar ◽  
Jarred C. Heigel ◽  
Eric Whitenton
Keyword(s):  
Cooling Rate ◽  
High Speed ◽  
Nickel Superalloy ◽  
Powder Bed Fusion ◽  
Support Structures ◽  
Radiance Temperature ◽  
Laser Powder Bed Fusion ◽  
Powder Bed ◽  
Melt Pool

This document provides details on the experiment and associated measurement files available fordownload in the dataset “In Situ Thermography During Laser Powder Bed Fusion of a Nickel Superalloy 625 Artifact with Various Overhangs and Supports.” The measurements were acquired during the fabrication of a small nickel superalloy 625 (IN625) artifact using a commercial laser powder bed fusion (LPBF) system. The artifact consists of two half-arch features with increasing slopes for overhangs. These overhangs range from 5° from vertical to 85° from vertical in increments of 10°. The artifact geometry and process are controlled to ensure consistent processing along the overhang geometry. This control enables the effect of overhang geometry and support structures to be isolated from effects of inter-layer scan strategy variations. The measurements include high-speed thermography of each layer, from which radiance temperature, cooling rate, and melt pool length are calculated.

Microstructure and corrosion properties of sensitized laser powder bed fusion printed Inconel 718 to dissolve support structures in a self-terminating manner

2019 ◽  
Vol 27 ◽  
pp. 526-532
Author(s):  
Christopher S. Lefky ◽  
Thomas G. Gallmeyer ◽  
Senthamilaruvi Moorthy ◽  
Aaron Stebner ◽  
Owen J. Hildreth
Keyword(s):  
Inconel 718 ◽  
Powder Bed Fusion ◽  
Support Structures ◽  
Laser Powder Bed Fusion ◽  
Corrosion Properties ◽  
Powder Bed

scholarly journals Laser Powder Bed Fusion of Stainless Steel Grades: A Review

Metals ◽  
2019 ◽  
Vol 9 (7) ◽  
pp. 731 ◽  
Author(s):  
Zitelli ◽  
Folgarait ◽  
Di Schino
Keyword(s):  
Surface Roughness ◽  
Stainless Steel ◽  
Stainless Steels ◽  
Precipitation Hardening ◽  
Powder Bed Fusion ◽  
Laser Powder Bed Fusion ◽  
Steel Alloys ◽  
Powder Bed ◽  
Steel Grades ◽  
Mechanical Performances

In this paper, the capability of laser powder bed fusion (L-PBF) systems to process stainless steel alloys is reviewed. Several classes of stainless steels are analyzed (i.e., austenitic, martensitic, precipitation hardening and duplex), showing the possibility of satisfactorily processing this class of materials and suggesting an enlargement of the list of alloys that can be manufactured, targeting different applications. In particular, it is reported that stainless steel alloys can be satisfactorily processed, and their mechanical performances allow them to be put into service. Porosities inside manufactured components are extremely low, and are comparable to conventionally processed materials. Mechanical performances are even higher than standard requirements. Micro surface roughness typical of the as-built material can act as a crack initiator, reducing the strength in both quasi-static and dynamic conditions.

Sign in / Sign up

Export Citation Format

Share Document