scholarly journals Optimizing of the Cementitious Composite Matrix by Addition of Steel Wool Fibers (Chopped) Based on Physical and Mechanical Analysis

Materials ◽  
2021 ◽  
Vol 14 (5) ◽  
pp. 1094
Author(s):  
Akrm A. Rmdan Amer ◽  
Mohd Mustafa Al Bakri Abdullah ◽  
Yun Ming Liew ◽  
Ikmal Hakem A. Aziz ◽  
Jerzy J. Wysłocki ◽  
...  
Keyword(s):  
Compressive Strength ◽  
Flexural Strength ◽  
High Strength ◽  
Mechanical Analysis ◽  
Primary Reinforcement ◽  
Physicomechanical Properties ◽  
Cementitious Composite ◽  
Steel Wool ◽  
Composite Matrix ◽  
Wool Fibers

The demand for durable, resistant, and high-strength structural material has led to the use of fibers as reinforcing elements. This paper presents an investigation into the inclusion of chopped steel wool fibers (CSWFs) in cement to form a high-flexural strength cementitious composite matrix (CCM). CSWFs were used as the primary reinforcement in CCM at increments of 0.5 wt%, from 0.5–6 wt%, with ratios of cement to sand of 1:1.5 and water to cement of 0.45. The inclusion of CSWFs resulted in an excellent optimization of the physicomechanical properties of the CCM, such as its density (2.302 g/cm3), compressive strength (61.452 MPa), and maximum flexural strength (10.64 MPa), all of which exceeded the performances of other reinforcement elements reported in the literature.

scholarly journals Properties of High-Strength Flowable Mortar Reinforced with Palm Fibers

2012 ◽  
Vol 2012 ◽  
pp. 1-5 ◽  
Author(s):  
Eethar Thanon Dawood ◽  
Mahyuddin Ramli
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Flexural Strength ◽  
Physical And Mechanical Properties ◽  
High Strength ◽  
Test Results ◽  
Palm Fiber ◽  
Toughness Index ◽  
Strength And Toughness

This study was conducted to determine some physical and mechanical properties of high-strength flowable mortar reinforced with different percentages of palm fiber (0, 0.2, 0.4, 0.6, 0.8, 1.0, 1.2, 1.4, and 1.6% as volumetric fractions). The density, compressive strength, flexural strength, and toughness index were tested to determine the mechanical properties of this mortar. Test results illustrate that the inclusion of this fiber reduces the density of mortar. The use of 0.6% of palm fiber increases the compressive strength and flexural strength by about 15.1%, and 16%, respectively; besides, the toughness index (I5) of the high-strength flowable mortar has been significantly enhanced by the use of 1% and more of palm fiber.

scholarly journals Influence of Hybrid Fibers on Toughness Behavior of High Strength Flowing Concrete

2011 ◽  
Vol 57 (3) ◽  
pp. 249-260 ◽  
Author(s):  
Eethar Thanon Dawood ◽  
Mahyuddin Ramli
Keyword(s):  
Compressive Strength ◽  
Flexural Strength ◽  
Modulus Of Elasticity ◽  
Hybrid Composite ◽  
High Strength ◽  
Steel Fibers ◽  
Hybrid Fibers ◽  
Static Modulus ◽  
Static Modulus Of Elasticity ◽  
Strength And Toughness

Abstract This study investigates the use of steel fibers and hybrid composite with a total fibers content of 2% on the high strength flowing concrete and determines the density, compressive strength, static modulus of elasticity, flexural strength and toughness indices for the mixes. The results show that the inclusion of more than 0.5% of palm fibers in hybrid fibers mixes reduces the compressive strength. The hybrid fibers can be considered as a promising concept and the replacement of a portion of steel fibers with palm fibers can significantly reduce the density, enhance the flexural strength and toughness. The results also indicates that the use of hybrid fibers (1.5 steel fibers + 0.5% palm fibers) in specimens increases significantly the toughness indices and thus the use of hybrid fibers combinations in reinforced concrete would enhance their flexural toughness & rigidity and enhance their overall performances

scholarly journals Kajian Karakteristik Beton Memadat Sendiri yang Menggunakan Serat Ijuk (Hal. 54-65)

2018 ◽  
Vol 4 (4) ◽  
pp. 54
Author(s):  
Iis Nurjamilah ◽  
Abinhot Sihotang
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Flexural Strength ◽  
Coarse Aggregate ◽  
Fresh Concrete ◽  
High Strength ◽  
Self Compacting Concrete ◽  
Palm Fiber ◽  
Fiber Concrete ◽  
Dilute Mixture

ABSTRAKKajian karakteristik beton memadat sendiri yang menggunakan serat ijuk merupakan sebuah kajian yang dilakukan untuk mengetahui pengaruh penambahan serat ijuk terhadap karakteristik beton memadat sendiri (SCC). Beton memadat sendiri yang menggunakan serat ijuk (PFSCC) didesain memiliki campuran yang encer, bermutu tinggi (= 40 MPa) dan memiliki persentase kekuatan lentur yang lebih baik. PFSCC  didapatkan dari hasil pencampuran antara semen sebanyak 85%, fly ash 15%, superplastizicer 1,5%, serat ijuk 0%, 0,5%; 1%; 1,5%; 2% dan 3% dari berat binder (semen + fly ash), kadar air 190 kg/m3, agregat kasar 552,47 kg/m3 dan pasir 1.063 kg/m3. Semakin banyak persentase penambahan serat ijuk ke dalam campuran berdampak terhadap menurunnya workability beton segar. Penambahan serat ijuk yang paling baik adalah sebanyak 1%, penambahan tersebut dapat meningkatkan kekuatan tekan beton sebesar 13% dan lentur sebesar 1,8%.Kata kunci: beton memadat sendiri (SCC), beton berserat, beton memadat sendiri yang menggunakan serat ijuk (PFSCC), serat ijuk ABSTRACTThe study of characteristics self compacting concrete using palm fibers is a study conducted to determine the effect of adding palm fibers to characteristics of self compacting concrete (SCC). palm fibers self compacting concrete (PFSCC) is designed to have a dilute mixture, high strength (= 40 MPa), and have better precentage flexural strength. PFSCC was obtained from mixing of 85% cement, 15% fly ash, 1.5% superplastizicer, 0%, 0.5%, 1%, 1.5%, 2% and 3% palm fibers from the weight of binder  (cement + fly ash), water content 190 kg/m3, coarse aggregate 552.47 kg/m3 and sand 1,063 kg/m3. The more persentage palm fibers content added to the mixture makes workability of fresh concrete decreases. The best addition of palm fiber is 1%, this addition can increases the compressive strength 13% and flexural strength 1.8%.Keywords: self compacting concrete (SCC), fiber concrete, Palm fiber self compacting concrete (PFSCC), palm fiber

scholarly journals Strength Characteristics of High Strength Concrete (HSC) with and without Coarse Aggregate

2019 ◽  
Vol 9 (2) ◽  
pp. 4701-4704
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Fly Ash ◽  
Flexural Strength ◽  
Silica Fume ◽  
High Strength Concrete ◽  
Mechanical Characteristics ◽  
Coarse Aggregate ◽  
High Strength ◽  
Set Up

This paper aimed to investigate the mechanical characteristics of HSC of M60 concrete adding 25% of fly ash to cement and sand and percentage variations of silica fumes 0%,5% and 10% to cement with varying sizes of 10mm,6mm,2mm and powder of granite aggregate with w/c of 0.32. Specimens are tested for compressive strength using 10cm X 10cmX10cm cubes for 7,14,28 days flexural strength was determined by using 10cmX10cmX50cm beam specimens at 28 days and 15cm diameter and 30cm height cylinder specimens at 28 days using super plasticizers of conplast 430 as a water reducing agent. In this paper the experimental set up is made to study the mechanical properties of HSC with and without coarse aggregate with varying sizes as 10mm, 6mm, 2mm and powder. Similarly, the effect of silica fume on HSC by varying its percentages as 0%, 5% and 10% in the mix studied. For all mixes 25% extra fly ash has been added for cement and sand.

Utilization of Waste Packaging Glass as Progressive Filler in Polymer Anchor Material Based on Epoxy Resin

2019 ◽  
Vol 887 ◽  
pp. 40-47
Author(s):  
Tomáš Žlebek ◽  
Jakub Hodul ◽  
Rostislav Drochytka
Keyword(s):  
Compressive Strength ◽  
Flexural Strength ◽  
Epoxy Resin ◽  
High Strength Concrete ◽  
Chemical Resistance ◽  
Negative Impact ◽  
High Strength ◽  
Pull Out ◽  
Pull Out Strength ◽  
Packaging Glass

The work deals with the use of waste glass to the polymer anchor material based on epoxy resin, primarily for anchoring to a high strength concrete (HSC). The main aim was to use the largest possible amount of the waste packaging glass by reducing the amount of epoxy resin, which is an expensive material and its production has a negative impact on the environment. Within the experimental verification, the influence of waste packaging glass fraction 0–0.63 mm on the final properties of the polymer anchoring material was observed. To determine the optimal formulation compressive strength, flexural strength, chemical resistance, shrinkage and pull-out test were performed. Based on the evaluation of the results the optimal percentage of filling was determined, when the polymer anchor material showed high strengths, minimal shrinkage, good chemical resistance, optimal consistency for anchoring into the HSC and high anchor bolt pull-out strength.

Influence of Foaming Agent on the Properties of High Density Foam Concrete

2011 ◽  
Vol 399-401 ◽  
pp. 1214-1217 ◽  
Author(s):  
Xin Gang Yu ◽  
Yan Na Gao ◽  
Lin Lin ◽  
Fang Li
Keyword(s):  
Compressive Strength ◽  
Flexural Strength ◽  
Lightweight Concrete ◽  
Drying Shrinkage ◽  
High Strength ◽  
High Density ◽  
Low Density ◽  
Dilution Ratio ◽  
Foam Concrete ◽  
Foaming Agent

Lightweight concrete has been used for structural purposes for many years and it is developed very fast in resent years due to its lightweight and favourable for insulation properties. High strength foam concrete is a fairly new kind of lightweight concrete with excellent properties of outstanding workability, low density and high strength. Responsible for these properties are the macro-, meso- and micro- porosity of the foam concrete which are mainly affected by the foaming agent. The influence of foaming agent’s dilution ratio and foam dosage on the fluidity, compressive strength, flexural strength and drying shrinkage of high density foam concrete designed for structural materials is investigated in this paper.

Test Research on Strength of Concrete Shaft Lining under Salt Disaster Corrosion

2014 ◽  
Vol 926-930 ◽  
pp. 645-648 ◽  
Author(s):  
Xu Rong Li ◽  
Hong Guang Ji ◽  
Jun Wang ◽  
Cheng Lin Song
Keyword(s):  
Compressive Strength ◽  
Flexural Strength ◽  
High Strength Concrete ◽  
High Strength ◽  
Solution Concentration ◽  
Test Results ◽  
Strength Concrete ◽  
Strength Change ◽  
Lining Structure ◽  
Shaft Lining

In order to study the strength change of high strength concrete shaft lining structure in underground complex environment resisting composite salt damage erosion, C70 high strength concrete test specimens were made and composite salt disaster solutions of different concentrations were compounded. The test results show that the coefficient of compressive strength and flexural strength of high strength concrete increase in early corrosion and then decline. The strength of specimen declines more quickly in higher corrosion solution concentration in latter time. The change law of the flexural strength is more complex than the compressive strength. Composite salt disaster solutions have little effect for no damage high strength concrete.

Mechanical Properties of Modified Polypropylene Coarse Fiber-Reinforced, High-Strength, Lightweight Concrete

2011 ◽  
Vol 374-377 ◽  
pp. 1499-1506
Author(s):  
Rong Hui Zhang ◽  
Jian Li
Keyword(s):  
Mechanical Properties ◽  
Fracture Toughness ◽  
Compressive Strength ◽  
Flexural Strength ◽  
Lightweight Concrete ◽  
Volume Fraction ◽  
High Strength ◽  
Lightweight Aggregate Concrete ◽  
Fiber Reinforced ◽  
Fiber Volume

In this study, the effect of micro-expansion high strength grouting material (EGM) and Modified polypropylene coarse fiber (M-PP fiber) on the mechanical properties of lightweight concrete are investigated. The influence of EGM and M-PP fiber on compressive strength , flexural strength and drying shrinkage of concrete are researched, and flexural fracture toughness are calculated. Test results show that the effect of EGM and M-PP fiber volume fraction (Vf) on flexural strength and fracture toughness is extremely prominent, compressive strength is only slightly enhanced, and the rate of shrinkage is obviously decreased. It is observed that the shape of the descending branch of load-deflection and the ascending branch of shrinkage-age tends towards gently with the increase of Vf. And M-PP fiber reinforced lightweight aggregate concrete is more economical.

scholarly journals Effect of polypropylene fibers on high strength mortar subjected to elevated temperature

2020 ◽  
Vol 156 ◽  
pp. 05010
Author(s):  
Muhammad Ridwan ◽  
Hu Liang Jun ◽  
Isamu Yoshitake
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Elevated Temperature ◽  
Flexural Strength ◽  
Fiber Length ◽  
Heating Temperature ◽  
High Strength ◽  
Polypropylene Fibers ◽  
Slump Flow ◽  
Residual Mechanical Properties

This study focuses on the thermo-mechanical properties of mortar in the retrofitting cover of additional reinforcement for existing concrete structures. In addition, the residual mechanical properties of high strength mortar incorporating polypropylene fibers subjected to the effect of fiber length and the elevated temperature were investigated. Several experiments were conducted to determine the optimum mixture proportions of high strength mortar incorporating polypropylene fibers which had a slump-flow of 25–30 cm, compressive strength of 50 MPa or higher, and flexural strength of 4–8 MPa. Subsequently, an experiment was conducted by using high-strength mortar-blended polypropylene fibers with a length of 2 cm, and the ratio of fiber length to the diameter of cylinder mortar-specimens was 0.4. The experimental parameters were the weight volume of fibers (0 %, 0.5 %, 1 %, and 2%) and the heating temperature (100, 200 and 300 °C). The effect of the mixing parameters, including polypropylene length on compressive strength, slump-flow and the flexural strength of mortar were discussed. It is evident that fiber in the mortar cover influenced the initial and residual mechanical properties, such as elasticity, compressive strength, and Poisson’s ratio, of the mortar.

Sign in / Sign up

Export Citation Format

Share Document