scholarly journals Kajian Karakteristik Beton Memadat Sendiri yang Menggunakan Serat Ijuk (Hal. 54-65)

2018 ◽  
Vol 4 (4) ◽  
pp. 54
Author(s):  
Iis Nurjamilah ◽  
Abinhot Sihotang
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Flexural Strength ◽  
Coarse Aggregate ◽  
Fresh Concrete ◽  
High Strength ◽  
Self Compacting Concrete ◽  
Palm Fiber ◽  
Fiber Concrete ◽  
Dilute Mixture

ABSTRAKKajian karakteristik beton memadat sendiri yang menggunakan serat ijuk merupakan sebuah kajian yang dilakukan untuk mengetahui pengaruh penambahan serat ijuk terhadap karakteristik beton memadat sendiri (SCC). Beton memadat sendiri yang menggunakan serat ijuk (PFSCC) didesain memiliki campuran yang encer, bermutu tinggi (= 40 MPa) dan memiliki persentase kekuatan lentur yang lebih baik. PFSCC  didapatkan dari hasil pencampuran antara semen sebanyak 85%, fly ash 15%, superplastizicer 1,5%, serat ijuk 0%, 0,5%; 1%; 1,5%; 2% dan 3% dari berat binder (semen + fly ash), kadar air 190 kg/m3, agregat kasar 552,47 kg/m3 dan pasir 1.063 kg/m3. Semakin banyak persentase penambahan serat ijuk ke dalam campuran berdampak terhadap menurunnya workability beton segar. Penambahan serat ijuk yang paling baik adalah sebanyak 1%, penambahan tersebut dapat meningkatkan kekuatan tekan beton sebesar 13% dan lentur sebesar 1,8%.Kata kunci: beton memadat sendiri (SCC), beton berserat, beton memadat sendiri yang menggunakan serat ijuk (PFSCC), serat ijuk ABSTRACTThe study of characteristics self compacting concrete using palm fibers is a study conducted to determine the effect of adding palm fibers to characteristics of self compacting concrete (SCC). palm fibers self compacting concrete (PFSCC) is designed to have a dilute mixture, high strength (= 40 MPa), and have better precentage flexural strength. PFSCC was obtained from mixing of 85% cement, 15% fly ash, 1.5% superplastizicer, 0%, 0.5%, 1%, 1.5%, 2% and 3% palm fibers from the weight of binder  (cement + fly ash), water content 190 kg/m3, coarse aggregate 552.47 kg/m3 and sand 1,063 kg/m3. The more persentage palm fibers content added to the mixture makes workability of fresh concrete decreases. The best addition of palm fiber is 1%, this addition can increases the compressive strength 13% and flexural strength 1.8%.Keywords: self compacting concrete (SCC), fiber concrete, Palm fiber self compacting concrete (PFSCC), palm fiber

scholarly journals Strength Characteristics of High Strength Concrete (HSC) with and without Coarse Aggregate

2019 ◽  
Vol 9 (2) ◽  
pp. 4701-4704
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Fly Ash ◽  
Flexural Strength ◽  
Silica Fume ◽  
High Strength Concrete ◽  
Mechanical Characteristics ◽  
Coarse Aggregate ◽  
High Strength ◽  
Set Up

This paper aimed to investigate the mechanical characteristics of HSC of M60 concrete adding 25% of fly ash to cement and sand and percentage variations of silica fumes 0%,5% and 10% to cement with varying sizes of 10mm,6mm,2mm and powder of granite aggregate with w/c of 0.32. Specimens are tested for compressive strength using 10cm X 10cmX10cm cubes for 7,14,28 days flexural strength was determined by using 10cmX10cmX50cm beam specimens at 28 days and 15cm diameter and 30cm height cylinder specimens at 28 days using super plasticizers of conplast 430 as a water reducing agent. In this paper the experimental set up is made to study the mechanical properties of HSC with and without coarse aggregate with varying sizes as 10mm, 6mm, 2mm and powder. Similarly, the effect of silica fume on HSC by varying its percentages as 0%, 5% and 10% in the mix studied. For all mixes 25% extra fly ash has been added for cement and sand.

scholarly journals Properties of High-Strength Flowable Mortar Reinforced with Palm Fibers

2012 ◽  
Vol 2012 ◽  
pp. 1-5 ◽  
Author(s):  
Eethar Thanon Dawood ◽  
Mahyuddin Ramli
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Flexural Strength ◽  
Physical And Mechanical Properties ◽  
High Strength ◽  
Test Results ◽  
Palm Fiber ◽  
Toughness Index ◽  
Strength And Toughness

This study was conducted to determine some physical and mechanical properties of high-strength flowable mortar reinforced with different percentages of palm fiber (0, 0.2, 0.4, 0.6, 0.8, 1.0, 1.2, 1.4, and 1.6% as volumetric fractions). The density, compressive strength, flexural strength, and toughness index were tested to determine the mechanical properties of this mortar. Test results illustrate that the inclusion of this fiber reduces the density of mortar. The use of 0.6% of palm fiber increases the compressive strength and flexural strength by about 15.1%, and 16%, respectively; besides, the toughness index (I5) of the high-strength flowable mortar has been significantly enhanced by the use of 1% and more of palm fiber.

scholarly journals Examining Polyethylene Terephthalate (PET) as Artificial Coarse Aggregates in Concrete

2020 ◽  
Vol 6 (12) ◽  
pp. 2416-2424
Author(s):  
Erniati Bachtiar ◽  
Mustaan Mustaan ◽  
Faris Jumawan ◽  
Meldawati Artayani ◽  
Tahang Tahang ◽  
...  
Keyword(s):  
Compressive Strength ◽  
Flexural Strength ◽  
Polyethylene Terephthalate ◽  
Coarse Aggregate ◽  
Fresh Concrete ◽  
Coarse Aggregates ◽  
Volume Weight ◽  
Concrete Mixtures ◽  
Strength Tests ◽  
Recycled Polyethylene

This study aims to examine the effect of recycled Polyethylene Terephthalate (PET) artificial aggregate as a substitute for coarse aggregate on the compressive strength and flexural strength, and the volume weight of the concrete. PET plastic waste is recycled by heating to a boiling point of approximately 300°C. There are five variations of concrete mixtures, defined the percentage of PET artificial aggregate to the total coarse aggregate, by 0, 25, 50, 75 and 100%. Tests carried out on fresh concrete mixtures are slump, bleeding, and segregation tests. Compressive and flexural strength tests proceeded based on ASTM 39/C39M-99 and ASTM C293-79 standards at the age of 28 days. The results showed that the use of PET artificial aggregate could improve the workability of the concrete mixture. The effect of PET artificial aggregate as a substitute for coarse aggregate on the compressive and flexural strength of concrete is considered very significant. The higher the percentage of PET plastic artificial aggregate, the lower the compressive and flexural strength, and the volume weight, of the concrete. Substitution of 25, 50, 75 and 100% of PET artificial aggregate gave decreases in compressive strength of 30.06, 32.39, 41.73 and 44.06% of the compressive strength of the standard concrete (18.20 MPa), respectively. The reductions in flexural strength were by respectively 19.03, 54.50, 53.95 and 61.00% of the standard concrete's flexural strength (3.59 MPa). The reductions in volume weight of concrete were by respectively 8.45, 17.71, 25.07 and 34.60% of the weight of the standard concrete volume of 2335.4 kg/m3 Doi: 10.28991/cej-2020-03091626 Full Text: PDF

scholarly journals Study of Fly Ash, Rice Husk Ash and Marble Powder as Partial Replacement to Cement in Concrete

2020 ◽  
Vol 13 (3) ◽  
pp. 315-321
Author(s):  
Dhiraj Ahiwale ◽  
Rushikesh Khartode
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Flexural Strength ◽  
Rice Husk ◽  
Coarse Aggregate ◽  
Rice Husk Ash ◽  
Partial Replacement ◽  
Scale Production ◽  
Environmental Threat ◽  
Marble Powder

Now days, the waste rice husk from rice mill, marble powder from tile industry and fly ash from steam power plant are necessary to utilize as partial replacement of cement for concrete production. Large scale production of cement required consumption of raw materials and energy as well as emissions to air which posse’s environmental threat in various areas of country. Apart from the environmental threat, there still exists the problem of shortage in many areas. Therefore, substitute material for concrete needs to be considered. The paper aims to analyze the compressive strength of concrete cubes and flexural strength of concrete beams made from partially replaced cement, sand, and coarse aggregate. This research study adopted in laboratory on 48 total specimens of grade M25 concrete cubes of size 150x150x150mm and concrte beams of size 100x100x500mm were casted. Out of the 48 concrete specimens cast, 6 each were made out 10%, 20%, and 30 % replacement of fly ash, rice husk ash and marble powder to cement in concrete. It was found that the compressive strength and flexural strength of concrete made from the mixture of 20 % partially replaced cement, sand and coarse aggregate was similar than the concrete made from without replaced cement , sand and coarse aggregate.

scholarly journals Experimental Study on Light Weight Concrete Using Coconut Shell and Fly Ash

2022 ◽  
Vol 10 (1) ◽  
pp. 752-758
Author(s):  
Barkha Verma
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Coarse Aggregate ◽  
Lightweight Concrete ◽  
Fresh Concrete ◽  
Industrial Wastes ◽  
Coconut Shell ◽  
Fine Aggregate ◽  
Concrete Production ◽  
Coconut Shells

Abstract: Aggregates provide volume at low cost, comprising 66% to 78% of the concrete. With increasing concern over the excessive exploitation of natural and quality aggregates, the aggregate produced from industrial wastes and agricultural wastes is the viable new source for building material. This study was carried out to determine the possibilities of using coconut shells as aggregate in concrete. Utilizing coconut shells as aggregate in concrete production not only solves the problem of disposing of this solid waste but also helps conserve natural resources. In this paper, the physical properties of crushed coconut shell aggregate were presented. The fresh concrete properties such as the density and slump and 28 days compressive strength of lightweight concrete made with coconut shell as coarse aggregate were also presented. The findings indicate that water absorption of the coconut shell aggregate was high about 24% but crushing value and impact value were comparable to that of other lightweight aggregates. The average fresh concrete density and 28days cube compressive strength of the concrete using coconut shell aggregate 1975kg/m3 and 19.1 N/mm2 respectively. It is concluded that crushed coconut shell is suitable when it is used as a substitute for conventional aggregates in lightweight concrete production. Keywords: Coarse Aggregate, Cement, Concrete, Fly Ash, Coconut shell Aggregate, Water, Compressive Strength, Workability, Fine Aggregate.

scholarly journals The effects of steel fiber waste tyre on properties of high strength fly ash concrete

2019 ◽  
Vol 276 ◽  
pp. 01008
Author(s):  
Fauzan ◽  
Rudy Kurniawan ◽  
Claudia Lovina A. N ◽  
Oscar Fitrah N ◽  
Putri Basenda T
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Fly Ash ◽  
Flexural Strength ◽  
High Strength Concrete ◽  
Steel Fiber ◽  
High Strength ◽  
Fly Ash Concrete ◽  
Waste Tyres ◽  
Waste Tyre

The utilization of steel fiber from waste tyres can be an alternative to reduce waste tyres due to the increase of tyre production in Indonesia annually. Steel fiber from waste tyre can be added to concrete mix to improve the concrete properties. In this study, the effects of steel fiber waste tyre (SFWT) on high strength concrete containing fly ash was investigated experimentally. The content of fly ash in the high strength concrete is 30% of being partially replaced the cement weight. Steel fiber waste tyres are obtained from extracting the steel wire of the waste tyres and then cut into 4 cm long. The addition of SFWT on the high strength fly ash concrete is 0.5%, 1.0%, 1.5%, and 2% by concrete volume. The mechanical properties of concrete such as compressive strength, tensile strength, and flexural strength are tested at day 28. The test results show that the addition of 2 % SFWT on high strength fly ash concrete increase the compressive strength, tensile strength, and flexural strength of the concrete by around 9.99 %, 63.75 %, 18.18 %, respectively.

Research on Self-Compacting Concrete Made with Recycled Aggregate

2013 ◽  
Vol 639-640 ◽  
pp. 399-403
Author(s):  
Ai Guo Zhou ◽  
Jian Yin ◽  
Wei Min Song ◽  
Yi Chi
Keyword(s):  
Compressive Strength ◽  
Flexural Strength ◽  
Coarse Aggregate ◽  
Recycled Aggregate ◽  
Self Compacting Concrete ◽  
Recycled Coarse Aggregate ◽  
Coarse Aggregates ◽  
Mineral Additive ◽  
Binder Ratio ◽  
Water Binder Ratio

It is studied the effect of binder quantity, water binder ratio on properties of self-compacting concrete made with recycled coarse aggregates. It can be prepared C50 self-compacting concrete made with recycled coarse aggregate by adjusting send proportion, binder quantity, and mixing mineral additive. For example, when the binder quantity is 600 kg/m3, water binder ratio is 0.28, the flexural strength and compressive strength at 28 days of self-compacting concrete made with recycled coarse aggregates are 9.07 MPa and 68.47 MPa respectively.

The Study of Oil Palm Shell (OPS) Lightweight Concrete Using Superplasticizer, Silica Fume, and Fly Ash

2017 ◽  
Vol 902 ◽  
pp. 65-73 ◽  
Author(s):  
Elly Tjahjono ◽  
Ayudia M. Fani ◽  
Dodorus D. Dodi ◽  
Erinda P. Purnamasari ◽  
Feny A. Silaban ◽  
...  
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Flexural Strength ◽  
Oil Palm ◽  
Coarse Aggregate ◽  
Lightweight Concrete ◽  
Crude Palm Oil ◽  
Concrete Technology ◽  
Palm Shell ◽  
Oil Palm Shell

The concrete technology has been growing significantly since years ago especially in Indonesia’s construction. Therefore, Indonesia needs new innovation of concrete technology to solve the problem for the availability of concrete material. Indonesia is known as the largest producer of crude palm oil (CPO) in the world. Oil palm shell (OPS) is one of the solid wastes produced in crude palm oil industry that can be used as concrete materials. This paper presents the experimental results of a research project to produce structural lightweight concrete using oil palm shell (OPS), as a coarse aggregate. This experimental was investigating the effects of adding silica fume, fly ash, and superplasticizer for the compressive strength and flexural strength of the OPS lightweight concrete. It was found that OPS lightweight concrete has compressive strength up to 23.90 MPa in 28-days and flexural strength up to 2.54 MPa in 28-days. This experimental concluded that OPS lightweight concrete has a good potential as a lightweight coarse aggregate and low-cost housing construction in Indonesia.

scholarly journals FRESH AND MECHANICAL CHARACTERISTICS OF SELF-COMPACTING POLYPROPYLENE FIBER CONCRETE INCORPORATED WITH KAOLIN

SINERGI ◽  
2020 ◽  
Vol 24 (3) ◽  
pp. 223
Author(s):  
Hakas Prayuda ◽  
Berkat Cipta Zega ◽  
Fanny Monika ◽  
Fadillawaty Saleh ◽  
Martyana Dwi Cahyati
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Flexural Strength ◽  
Concrete Beam ◽  
Polypropylene Fiber ◽  
Polypropylene Fibers ◽  
Flexural Test ◽  
Self Compacting Concrete ◽  
Additional Material ◽  
Fiber Concrete

Self Compacting Concrete (SCC) is concrete with high fluidity so that it can flow and fill the spaces in the mold without the compaction process. This study discusses the effect of the adding of kaolin and polypropylene fibers in order to increase the flowability, compressive strength, flexural strength, and tensile strength in self-compacting concrete. The additional material of kaolin was 5%, 10%, and 15% of the cement weight. The polypropylene fibers were 1%, 1.5%, and 2%. The flowability test, which was used, was Table flow, V-Funnel, and L-Box. Compressive strength testing was conducted when the concrete was 7, 14, and 28 days old. The flexural test was performed with a measurement of 150 x 150 x 600 mm as many as 18 specimens tested at the age of 28 days. The results showed that the addition of kaolin and polypropylene fibers met the flowability specifications of self-compacting concrete. The addition of polypropylene can increase the flexural strength and tensile strength of the concrete beam, but cannot increase the compressive strength of self-compacting concrete.

Sign in / Sign up

Export Citation Format

Share Document