scholarly journals Effect of Two Immediate Dentin Sealing Approaches on Bond Strength of Lava™ CAD/CAM Indirect Restoration

Materials ◽  
2021 ◽  
Vol 14 (7) ◽  
pp. 1629
Author(s):  
Hassan Faez Abdullah Gailani ◽  
Cristina Benavides-Reyes ◽  
María Victoria Bolaños-Carmona ◽  
Eva Rosel-Gallardo ◽  
Purificación González-Villafranca ◽  
...  
Keyword(s):  
Survival Analysis ◽  
Bond Strength ◽  
Computer Aided Design ◽  
Resin Cement ◽  
Competing Risk ◽  
Adhesive Resin ◽  
Computer Aided ◽  
Cad Cam ◽  
Aided Design ◽  
Type Of Failure

The objective of this work was to compare the micro-tensile bond strength (µTBS) of CAD/CAM (Computer-Aided Design/ Computer-Aided Manufacturing) specimens cemented with different pairing of adhesives and resin-cements using two Immediate Dentin Dealing (IDS) approaches in comparison with Delay Dentin Sealing (DDS). Coronal dentin from 108 molars were divided into nine groups (n = 12) depending on the adhesive/resin-cement (A-C) assigned. Lava™ Ultimate (4 × 10 × 10 mm) was cemented according to different strategies: IDS1(cementation after dentin sealing), DDS (dentin sealing and cementation at 2-weeks), IDS2 (immediate dentin sealing and cementation at 2-weeks). Samples were sectioned and tested until failure to determine the µTBS. Failure mode was categorized as dentin/cement (DC), at Lava™ Ultimate/cement (LC) and hybrid (H). Kruskal–Wallis and Mann–Whitney U tests and influence of the type of failure on the µTBS by survival analysis with competing risk was explored. Mostly, µTBS values were equal or higher in IDS2 than DDS. In general, A-Cs that showed higher µTBS, have high percentages of LC failure. Survival analysis with competing risk between DC + H and LC values showed that some A-Cs would significantly increase the µTBS values for IDS2. A-Cs with the highest adhesion values showed a high percentage of fractures at the LC interface, suggesting that the adhesion at the adhesive/dentin interface would be higher.

Premolar Axial Wall Height Effect on CAD/CAM Crown Retention

2016 ◽  
Vol 41 (6) ◽  
pp. 666-671 ◽  
Author(s):  
C Gillette ◽  
R Buck ◽  
N DuVall ◽  
S Cushen ◽  
M Wajdowicz ◽  
...  
Keyword(s):  
Computer Aided Design ◽  
Lithium Disilicate ◽  
Resin Cement ◽  
Failure Resistance ◽  
All Ceramic ◽  
Computer Aided ◽  
Cad Cam ◽  
Ceramic Crowns ◽  
Aided Design ◽  
Post Hoc

SUMMARY Objective: To evaluate the significance of reduced axial wall height on retention of adhesively luted, all-ceramic, lithium disilicate premolar computer-aided design/computer-aided manufacturing (CAD/CAM) crowns based on preparations with a near ideal total occlusal convergence of 10°. Methods: Forty-eight recently extracted premolars were randomly divided into four groups (n=12). Each group received all-ceramic CAD/CAM crown preparations featuring axial wall heights of 0, 1, 2, and 3 mm, respectively, all with a 10° total occlusal convergence. Scanned preparations were fitted with lithium disilicate all-ceramic crowns that were luted with a self-etching resin cement. Specimens were tested to failure at a 45° angle to the tooth long axis with failure load converted to megapascals (MPa) based on the measured bonding surface area. Mean data were analyzed using analysis of variance/Tukey's post hoc test (α=0.05). Results: Lithium disilicate crowns adhesively luted on preparations with 0 axial wall height demonstrated significantly less failure resistance compared with the crowns luted on preparations with axial wall heights of 1 to 3 mm. There was no failure stress difference between preparations with 1 to 3 mm axial wall height. Conclusions: Under conditions of this study, adhesively luted lithium disilicate bicuspid crowns with a total occlusal convergence of 10° demonstrated similar failure resistance independent of axial wall height of 1 to 3 mm. This study provides some evidence that adhesion combined with an ideal total occlusal convergence may compensate for reduced axial wall height.

scholarly journals An Esthetics Rehabilitation with Computer-aided Design/ Computer-aided Manufacturing Technology

2014 ◽  
Vol 15 (4) ◽  
pp. 506-512
Author(s):  
Adriana Cristina Zavanelli ◽  
José Vitor Quinelli Mazaro ◽  
Caroline Cantieri de Mello ◽  
Joel Ferreira Santiago ◽  
Andressa Paschoal Amoroso
Keyword(s):  
Computer Aided Design ◽  
Physical And Mechanical Properties ◽  
High Strength ◽  
Functional Results ◽  
Manufacturing Technology ◽  
Resin Cement ◽  
Computer Aided Manufacturing ◽  
Computer Aided ◽  
Cad Cam ◽  
Aided Design

ABSTRACT Aim This paper describes a case of a rehabilitation involving Computer Aided Design/Computer Aided Manufacturing (CADCAM) system in implant supported and dental supported prostheses using zirconia as framework. Background The CAD-CAM technology has developed considerably over last few years, becoming a reality in dental practice. Among the widely used systems are the systems based on zirconia which demonstrate important physical and mechanical properties of high strength, adequate fracture toughness, biocompatibility and esthetics, and are indicated for unitary prosthetic restorations and posterior and anterior framework. Case description All the modeling was performed by using CAD-CAM system and prostheses were cemented using resin cement best suited for each situation. Conclusion The rehabilitation of the maxillary arch using zirconia framework demonstrated satisfactory esthetic and functional results after a 12-month control and revealed no biological and technical complications. Clinical significance This article shows the important of use technology CAD/CAM in the manufacture of dental prosthesis and implant-supported. How to cite this article Mazaro JVQ, Mello CC, Zavanelli AC, Santiago JF Jr, Amoroso AP, Pellizzer EP. An Esthetics Rehabilitation with Computer-aided Design/Computer-aided Manufacturing Technology. J Contemp Dent Pract 2014;15(4): 506-512.

scholarly journals Effect of Thermocycling on the Bond Strength of Self-Adhesive Resin Cements Used for Luting CAD/CAM Ceramics to Human Dentin

2022 ◽  
Vol 23 (2) ◽  
pp. 745
Author(s):  
Andrzej Malysa ◽  
Joanna Wezgowiec ◽  
Wojciech Grzebieluch ◽  
Dariusz P. Danel ◽  
Mieszko Wieckiewicz
Keyword(s):  
Bond Strength ◽  
Computer Aided Design ◽  
Shear Bond Strength ◽  
Failure Modes ◽  
Dental Materials ◽  
Resin Cements ◽  
Computer Aided ◽  
Human Dentin ◽  
Cad Cam ◽  
Aided Design

The aim of the study was to evaluate the influence of thermocycling on the shear bond strength of self-adhesive, self-etching resin cements luted to human dentin and computer-aided design/computer-aided manufacturing (CAD/CAM) ceramics. Three modern self-adhesive dental cements (Maxcem Elite, RelyX U200, Panavia SA) were used to lute three CAD/CAM ceramics (IPS Empress CAD, IPS e.max CAD, IPS e.max ZirCAD) onto the dentin. One conventional cement (Panavia V5) served as a control. After preparation, the samples were subjected to thermocycling as a method of artificial aging of dental materials applied to simulate long-term use in oral conditions. Shear bond strength was evaluated according to PN-EN ISO 29022:2013-10 and failure modes were observed under a light microscope. Statistical analysis was performed. The study demonstrated that a combination of ceramics and cements directly impacts the bond strength. The highest bond strength was observed in Panavia V5, lower in Panavia SA and Maxcem Elite and the lowest–in RelyX U200. Adhesive failure between human dentin and cements was the most common failure mode. Moreover, thermocycling highly decreased bond strength of self-adhesive, self-etching cements.

Impact of Recently Developed Universal Adhesives on Tensile Bond Strength to Computer-aided Design/Manufacturing Ceramics

2019 ◽  
Vol 44 (4) ◽  
pp. 386-395 ◽  
Author(s):  
A Liebermann ◽  
J Detzer ◽  
B Stawarczyk
Keyword(s):  
Bond Strength ◽  
Computer Aided Design ◽  
Resin Composite ◽  
Tensile Bond Strength ◽  
Adhesive Systems ◽  
Computer Aided ◽  
Cad Cam ◽  
Aided Design ◽  
Failure Types ◽  
Resin Composite Cement

SUMMARY Objectives: The aim of this investigation was to test the tensile bond strength (TBS) between different computer-aided-design/manufacturing (CAD/CAM) ceramics after conditioning using different universal adhesive systems and resin composite cement. Methods and Materials: Substrates of four CAD/CAM ceramics—1) VITABLOCS Mark II, 2) Initial LRF, 3) Celtra Duo, and 4) IPS e.max CAD (N=648, n=162)—were fabricated. VITABLOCS Mark II and Initial LRF were etched using 9% hydrofluoric acid for 60 seconds, Celtra Duo for 30 seconds, and IPS e.max CAD for 20 seconds. Substrates for conditioning using Monobond Etch & Prime were untreated. The following adhesive systems were used: All-Bond Universal (ABU), Clearfil Universal Bond (CUB), G-Multi Primer (GMP), iBond Universal (IBU), Monobond Etch & Prime (MEP), Monobond Plus (MBP), One Coat 7 Universal (OCU), Prime&Bond Active (PBA), and Scotchbond Universal (SBU). Conditioned substrates were bonded using a resin composite cement (Variolink Esthetic DC), thermal cycled (20,000×, 5°C/55°C), and TBS was measured using a universal testing machine. Data were analyzed using univariate analysis with partial eta-squared, Kolmogorov-Smirnov, Kruskal-Wallis, Mann-Whitney U, and Spearman-Rho tests (α=0.05). Results: ABU, MEP, and MBP obtained the significantly highest TBS, while CUB, IBU, and OCO resulted in the lowest, regardless of the CAD/CAM ceramic. SBU showed varying TBS results depending on the CAD/CAM ceramic used. ABU, MEP, and MBP showed no impact of CAD/CAM ceramic on TBS values. ABU, GMP, MEP, and MBP showed predominantly cohesive failure types in luting composite, while CUB and OCU demonstrated adhesive failure types.

Structural Analysis of Product and Computer-Aided Assembly Planning in AssemBL Software Package

2018 ◽  
pp. 11-33
Author(s):  
A. N. Bozhko
Keyword(s):  
Computer Aided Design ◽  
State Of The Art ◽  
Graph Model ◽  
Design System ◽  
Assembly Planning ◽  
Complex Products ◽  
Assembly Sequences ◽  
Computer Aided ◽  
Cad Cam ◽  
Aided Design

Computer-aided design of assembly processes (Computer aided assembly planning, CAAP) of complex products is an important and urgent problem of state-of-the-art information technologies. Intensive research on CAAP has been underway since the 1980s. Meanwhile, specialized design systems were created to provide synthesis of assembly plans and product decompositions into assembly units. Such systems as ASPE, RAPID, XAP / 1, FLAPS, Archimedes, PRELEIDES, HAP, etc. can be given, as an example. These experimental developments did not get widespread use in industry, since they are based on the models of products with limited adequacy and require an expert’s active involvement in preparing initial information. The design tools for the state-of-the-art full-featured CAD/CAM systems (Siemens NX, Dassault CATIA and PTC Creo Elements / Pro), which are designed to provide CAAP, mainly take into account the geometric constraints that the design imposes on design solutions. These systems often synthesize technologically incorrect assembly sequences in which known technological heuristics are violated, for example orderliness in accuracy, consistency with the system of dimension chains, etc.An AssemBL software application package has been developed for a structured analysis of products and a synthesis of assembly plans and decompositions. The AssemBL uses a hyper-graph model of a product that correctly describes coherent and sequential assembly operations and processes. In terms of the hyper-graph model, an assembly operation is described as shrinkage of edge, an assembly plan is a sequence of shrinkages that converts a hyper-graph into the point, and a decomposition of product into assembly units is a hyper-graph partition into sub-graphs.The AssemBL solves the problem of minimizing the number of direct checks for geometric solvability when assembling complex products. This task is posed as a plus-sum two-person game of bicoloured brushing of an ordered set. In the paradigm of this model, the brushing operation is to check a certain structured fragment for solvability by collision detection methods. A rational brushing strategy minimizes the number of such checks.The package is integrated into the Siemens NX 10.0 computer-aided design system. This solution allowed us to combine specialized AssemBL tools with a developed toolkit of one of the most powerful and popular integrated CAD/CAM /CAE systems.

scholarly journals Evaluation of the Feasibility of NaCaPO4-Blended Zirconia as a New CAD/CAM Material for Dental Restoration

Materials ◽  
2021 ◽  
Vol 14 (14) ◽  
pp. 3819
Author(s):  
Ting-Hsun Lan ◽  
Yu-Feng Chen ◽  
Yen-Yun Wang ◽  
Mitch M. C. Chou
Keyword(s):  
Computer Aided Design ◽  
Optical Microscope ◽  
Dental Restoration ◽  
Numerical Control ◽  
Test Results ◽  
Cnc Machine ◽  
Computer Aided ◽  
Cad Cam ◽  
Aided Design ◽  
Better Than

The computer-aided design/computer-aided manufacturing (CAD/CAM) fabrication technique has become one of the hottest topics in the dental field. This technology can be applied to fixed partial dentures, removable dentures, and implant prostheses. This study aimed to evaluate the feasibility of NaCaPO4-blended zirconia as a new CAD/CAM material. Eleven different proportional samples of zirconia and NaCaPO4 (xZyN) were prepared and characterized by X-ray diffractometry (XRD) and Vickers microhardness, and the milling property of these new samples was tested via a digital optical microscope. After calcination at 950 °C for 4 h, XRD results showed that the intensity of tetragonal ZrO2 gradually decreased with an increase in the content of NaCaPO4. Furthermore, with the increase in NaCaPO4 content, the sintering became more obvious, which improved the densification of the sintered body and reduced its porosity. Specimens went through milling by a computer numerical control (CNC) machine, and the marginal integrity revealed that being sintered at 1350 °C was better than being sintered at 950 °C. Moreover, 7Z3N showed better marginal fit than that of 6Z4N among thirty-six samples when sintered at 1350 °C (p < 0.05). The milling test results revealed that 7Z3N could be a new CAD/CAM material for dental restoration use in the future.

scholarly journals Characterisation of the Filler Fraction in CAD/CAM Resin-Based Composites

Materials ◽  
2021 ◽  
Vol 14 (8) ◽  
pp. 1986
Author(s):  
Andreas Koenig ◽  
Julius Schmidtke ◽  
Leonie Schmohl ◽  
Sibylle Schneider-Feyrer ◽  
Martin Rosentritt ◽  
...  
Keyword(s):  
Computer Aided Design ◽  
Point Of View ◽  
Specific Information ◽  
Dental Resin ◽  
X Ray ◽  
Computer Aided ◽  
Cad Cam ◽  
Filler Fraction ◽  
The Individual ◽  
Aided Design

The performance of dental resin-based composites (RBCs) heavily depends on the characteristic properties of the individual filler fraction. As specific information regarding the properties of the filler fraction is often missing, the current study aims to characterize the filler fractions of several contemporary computer-aided design/computer-aided manufacturing (CAD/CAM) RBCs from a material science point of view. The filler fractions of seven commercially available CAD/CAM RBCs featuring different translucency variants were analysed using Scanning Electron Microscopy (SEM) with Energy Dispersive X-ray Spectroscopy (EDS), Micro-X-ray Computed Tomography (µXCT), Thermogravimetric Analysis (TG) and X-ray Diffractometry (XRD). All CAD/CAM RBCs investigated included midifill hybrid type filler fractions, and the size of the individual particles was clearly larger than the individual specifications of the manufacturer. The fillers in Shofu Block HC featured a sphericity of ≈0.8, while it was <0.7 in all other RBCs. All RBCs featured only X-ray amorphous phases. However, in Lava Ultimate, zircon crystals with low crystallinity were detected. In some CAD/CAM RBCs, inhomogeneities (X-ray opaque fillers or pores) with a size <80 µm were identified, but the effects were minor in relation to the total volume (<0.01 vol.%). The characteristic parameters of the filler fraction in RBCs are essential for the interpretation of the individual material’s mechanical and optical properties.

Sign in / Sign up

Export Citation Format

Share Document