Revealing Electrical and Mechanical Performances of Highly Oriented Electrospun Conductive Nanofibers of Biopolymers with Tunable Diameter

The present study outlines a reliable approach to determining the electrical conductivity and elasticity of highly oriented electrospun conductive nanofibers of biopolymers. The highly oriented conductive fibers are fabricated by blending a high molar mass polyethylene oxide (PEO), polycaprolactone (PCL), and polylactic acid (PLA) with polyaniline (PANi) filler. The filler-matrix interaction and molar mass (M) of host polymer are among governing factors for variable fiber diameter. The conductivity as a function of filler fraction (φ) is shown and described using a McLachlan equation to reveal the electrical percolation thresholds (φc) of the nanofibers. The molar mass of biopolymer, storage time, and annealing temperature are significant factors for φc. The Young’s modulus (E) of conductive fibers is dependent on filler fraction, molar mass, and post-annealing process. The combination of high orientation, tunable diameter, tunable conductivity, tunable elasticity, and biodegradability makes the presented nanofibers superior to the fibers described in previous literature and highly desirable for various biomedical and technical applications.

SPECIFIC FEATURES OF THE FORMATION OF THE MICROSTRUCTURE OF GRANULAR AGGREGATES ON DIFFERENT BINDING COMPOSITIONS (PART 2)

This article is a continuation of the previous research. It includes analysis of the formation of the structure of granular aggregates during the hydration of the binder composition of BC-2 (PC 500-D0-N + 20 % quartz sand), prepared in a jet vortex mill. The study reveals the features of the dispersion of the quartz mineral filler (fractions ≤0.16; ≤0.315; ≤0.63 mm) and the main patterns of influence on structure formation at hydration of binders, differing in the composition and dispersion of particles. The paper analyzes physical and mechanical tests of the samples with the best strength characteristics and studies the features of their microstructures. The study of the microstructures of the samples reveals regularities, consisting in the formation of crystalline phases of different densities. It is noted that the introduction of 20 % mineral finely dispersed filler into PC 500-D0-N, in the form of quartz sand, ensures the formation of dense sub-microcrystalline hydrate phases when using a filler fraction ≤0.63 mm, which contributes to an increase in the additional strength of the samples by more than 20 %. It has been found that the mineral filler plays the role of crystallization centers, binding individual grains of fillers and sealing general structure of the composite. More compact healing of the pore space has been established for the composite with small crystalline new formations of hydrated calcium silicate

Characterisation of the Filler Fraction in CAD/CAM Resin-Based Composites

The performance of dental resin-based composites (RBCs) heavily depends on the characteristic properties of the individual filler fraction. As specific information regarding the properties of the filler fraction is often missing, the current study aims to characterize the filler fractions of several contemporary computer-aided design/computer-aided manufacturing (CAD/CAM) RBCs from a material science point of view. The filler fractions of seven commercially available CAD/CAM RBCs featuring different translucency variants were analysed using Scanning Electron Microscopy (SEM) with Energy Dispersive X-ray Spectroscopy (EDS), Micro-X-ray Computed Tomography (µXCT), Thermogravimetric Analysis (TG) and X-ray Diffractometry (XRD). All CAD/CAM RBCs investigated included midifill hybrid type filler fractions, and the size of the individual particles was clearly larger than the individual specifications of the manufacturer. The fillers in Shofu Block HC featured a sphericity of ≈0.8, while it was <0.7 in all other RBCs. All RBCs featured only X-ray amorphous phases. However, in Lava Ultimate, zircon crystals with low crystallinity were detected. In some CAD/CAM RBCs, inhomogeneities (X-ray opaque fillers or pores) with a size <80 µm were identified, but the effects were minor in relation to the total volume (<0.01 vol.%). The characteristic parameters of the filler fraction in RBCs are essential for the interpretation of the individual material’s mechanical and optical properties.

Novel Core-Shell Structured Ironbark-Like TiO2 as Fillers for Excellent Discharged Energy Density of Nanocomposites

The perpendicular orientation of nanowires to electric fields would greatly improve the breakdown strengths (Eb) of polymer-based nanocomposites, however, the relatively small polarization at small filler fraction, and thus the unsatisfactory discharged energy density (Ud), greatly restrict their further application. In this study, x vol.% TO@TO/PVDF nanocomposites with superior energy storage performances have been fabricated, where the ironbark-like TiO2 fillers (TO@TO) with core-shell structures lead to greatly enhanced polarization and Eb simultaneously. The former is due to the coupling effects of the increased interfacial polarization, the latter is due to the enhanced path tortuosity of electric tree growing at small TO@TO fraction. Strikingly, an excellent Ud of 13.1 J/cm3 was achieved in the 1.5 vol % TO@TO/PVDF nanocomposite at 383 MV/m, which is greatly increased by 220% compared with that of pure PVDF (5.98 J/cm3). The primary results might provide a strategy to design and fabricate nanocomposites with satisfactory energy storage performances as well as the flexible and easy-processing ability at small filler fraction.

Thermal Properties of Binary Filler Hybrid Composite with Graphene Oxide and Pyrolyzed Silicon-Coated Boron Nitride

To improve the thermal conductivity of a composite material, the filler dispersion and the interfacial adhesion between the filler and the matrix are important factors. A number of methods for satisfying these criteria are presented herein. Thus, graphene oxide (GO) is incorporated to enhance the dispersion state of surface-modified boron nitride (BN) by increasing the viscosity of the epoxy matrix and by providing steric hindrance. Meanwhile, polysilazane (PSZ) coating and thermolysis were used to enhance the wettability by providing structural similarity between the coating material and the epoxy matrix. Due to these strategies, the thermal conductivity was improved by 253% compared to that of the neat epoxy at a filler fraction of 40 wt %.

Thermal Conductivity Performance of 2D h-BN/MoS2/-Hybrid Nanostructures Used on Natural and Synthetic Esters

In this paper, the thermal conductivity behavior of synthetic and natural esters reinforced with 2D nanostructures—single hexagonal boron nitride (h-BN), single molybdenum disulfide (MoS2), and hybrid h-BN/MOS2—were studied and compared to each other. As a basis for the synthesis of nanofluids, three biodegradable insulating lubricants were used: FR3TM and VG-100 were used as natural esters and MIDEL 7131 as a synthetic ester. Two-dimensional nanosheets of h-BN, MoS2, and their hybrid nanofillers (50/50 ratio percent) were incorporated into matrix lubricants without surfactants or additives. Nanofluids were prepared at 0.01, 0.05, 0.10, 0.15, and 0.25 weight percent of filler fraction. The experimental results revealed improvements in thermal conductivity in the range of 20–32% at 323 K with the addition of 2D nanostructures, and a synergistic behavior was observed for the hybrid h-BN/MoS2 nanostructures.

Calculation of the Electrical Conductivity of Polymer Nanocomposites Assuming the Interphase Layer Surrounding Carbon Nanotubes

The interphase layer surrounding nanoparticles can reflect the tunneling effect as the main mechanism of charge transferring in polymer/carbon nanotube (CNT) nanocomposites (PCNT). In this paper, the percolation threshold, effective volume fraction of CNT, and the portion of percolated filler after percolation are expressed by interphase and CNT waviness. Moreover, the developed terms are used to suggest the influences of CNT dimensions, interphase thickness, and waviness on the electrical conductivity of PCNT by conventional and developed models. Thin and long CNT, thick interphase, and low waviness obtain a high fraction of percolated CNT. However, the highest level of effective filler fraction is only calculated by the thinnest CNT and the thickest interphase. Furthermore, both models show that the thinnest and the longest CNT as well as the thickest interphase and the least CNT waviness cause the highest conductivity in PCNT, because they positively contribute to the formation and properties of the conductive network.

Solubility and Diffusivity of Polar and Non-Polar Molecules in Polyethylene-Aluminum Oxide Nanocomposites for HVDC Applications

The best commercial high-voltage insulation material of today is (crosslinked) ultra-pure low-density polyethylene (LDPE). A 100-fold decrease in electrical conductivity can be achieved by adding 1–3 wt.% of well-dispersed inorganic nanoparticles to the LDPE. One hypothesis is that the nanoparticle surfaces attract ions and polar molecules, thereby cleaning the surrounding polymer, and thus reducing the conductivity. LDPE-based nanocomposites with 1–12 wt.% octyl-coated aluminum oxide nanoparticles were prepared and the sorption and desorption of one polar compound (acetophenone, a crosslinking by-product) and one non-polar compound of a similar size (limonene) were examined. Since the uptake of acetophenone increased linearly with increasing filler content, whereas the uptake of limonene decreased, the surface attraction hypothesis was strengthened. The analytical functions for predicting composite solubility as a function of particle size and filler fraction were derived using experimental solubility measurements and Monte Carlo simulations.

Tribological and Thermal Transport Performance of SiO2-Based Natural Lubricants

Fluids and lubricants are critical for the mechanical manufacturing processing of metals, due to a high amount of friction generated, also reflected as heat, could wear and damage tooling and machine components. The proper application of lubricants increases machinery lifetime, decreases long-term costs, and energy and time consumption due to the maintenance or components exchange/repairs. Besides being non-renewable, mineral oils bring consequences to the environment due to their low biodegradability and could affect the user with respiratory and skin diseases. Recently, due to an increase in environmental awareness, the search of biocompatible and efficient lubricants has become a technology goal. The vegetable oil-based lubricants are slowly emerging as ecofriendly and high-performance alternatives to petroleum-based lubricants. This study evaluates soybean, sunflower, corn and paraffinic oils reinforced with SiO2 nanoparticles. The thermal and tribological evaluations were performed varying the temperature and nanofiller concentrations. The thermal conductivity improvements were observed for all nanolubricants as the temperature and filler fraction increased. The highest thermal conductivities were observed at 323 K with 0.25 wt % SiO2. The soybean and corn oils unveiled a maximum enhancement of ~11%. The tribological evaluations showed that SiO2 addition, even in small concentration, resulted into a significant improvement on a load-carrying capacity. For instance, at 0.25 wt % enhancements of 45% and 60% were observed for soybean and sunflower oils, respectively. The coefficient of friction performance also showed enhancements between 10% and 26%.