scholarly journals The Effect of Temper Condition and Feeding Speed on the Additive Manufacturing of AA2011 Parts Using Friction Stir Deposition

Materials ◽  
2021 ◽  
Vol 14 (21) ◽  
pp. 6396
Author(s):  
Mohamed M. Z. Ahmed ◽  
Mohamed M. El-Sayed Seleman ◽  
Ebtessam Elfishawy ◽  
Bandar Alzahrani ◽  
Kamel Touileb ◽  
...  
Keyword(s):  
Additive Manufacturing ◽  
Rotation Rate ◽  
Processing Parameters ◽  
Optical Microscope ◽  
Hardness Profile ◽  
Friction Stir ◽  
Material Hardness ◽  
Mapping Analysis ◽  
Feeding Speed ◽  
Selection Of

In the current study, solid-state additive manufacturing (SSAM) of two temper conditions AA2011 was successfully conducted using the friction stir deposition (FSD) process. The AA2011-T6 and AA2011-O consumable bars of 20 mm diameter were used as a feeding material against AA5083 substrate. The effect of the rotation rate and feeding speed of the consumable bars on the macrostructure, microstructure, and hardness of the friction stir deposited (FSD) materials were examined. The AA2011-T6 bars were deposited at a constant rotation rate of 1200 rpm and different feeding speeds of 3, 6, and 9 mm/min, whereas the AA2011-O bars were deposited at a constant rotation rate of 200 mm/min and varied feeding speeds of 1, 2, and 3 mm/min. The obtained microstructure was investigated using an optical microscope and scanning electron microscope equipped with EDS analysis to evaluate microstructural features. Hardness was also assessed as average values and maps. The results showed that this new technique succeeded in producing sound additive manufactured parts at all the applied processing parameters. The microstructures of the additive manufactured parts showed equiaxed refined grains compared to the coarse grain of the starting materials. The detected intermetallics in AA2011 alloy are mainly Al2Cu and Al7Cu2Fe. The improvement in hardness of AA2011-O AMPs reached 163% of the starting material hardness at the applied feeding speed of 1 mm/min. The hardness mapping analysis reveals a homogeneous hardness profile along the building direction. Finally, it can be said that the temper conditions of the starting AA2011 materials govern the selection of the processing parameters in terms of rotation rate and feeding speed and affects the properties of the produced additive manufactured parts in terms of hardness and microstructural features.

Effect of Friction Stir Processing Parameters on the Properties of AA7075-T73/Al2O3 Surface Metal Matrix Composite

2020 ◽  
Vol 1002 ◽  
pp. 140-150
Author(s):  
Ali H. Al-Helli ◽  
Ahmed R. Alhamaoy ◽  
Ayad Murad Takhakh
Keyword(s):  
Friction Stir Processing ◽  
Particle Distribution ◽  
Surface Hardness ◽  
Base Material ◽  
Processing Parameters ◽  
Optical Microscope ◽  
Friction Stir ◽  
Surface Composite ◽  
Surface Metal ◽  
Number Of Passes

Friction Stir Processing (FSP) technology was wielded to output the Al7075/ Al2O3 surface composite. The effects parameters of processing method on particle distribution have been studied. The microstructure and mechanical characteristics of the samples were examined using the optical microscope, SEM and hardness examination. Acquired consequences, showed that Al2O3 particles were in a good interior distribution inside the basement. This technique produced excellent bonding between the surface composite and the base material. On other hand the surface hardness was increased about 25% as compared with the substrate. In addition, grain matrix refinement and enhanced particle distribution were obtained after each FSP pass. Also the dispersion of Al2O3 particles in the stirred area became more homogeneous and the average hardness improved by increasing the number of passes.

Microstructure and Mechanical Properties of Friction Stir Welded Al-Zn-Mg-Cu Alloy

2014 ◽  
Vol 628 ◽  
pp. 7-11
Author(s):  
Sheng Dan Liu ◽  
Yun Dai ◽  
Yu Long Wu ◽  
Bin Chen ◽  
Xin Ming Zhang
Keyword(s):  
Mechanical Properties ◽  
Grain Boundaries ◽  
Base Material ◽  
Optical Microscope ◽  
Alloy Sheet ◽  
Grain Structure ◽  
Hardness Profile ◽  
Friction Stir ◽  
Cu Alloy ◽  
Microstructure And Mechanical Properties

The microstructure and mechanical properties of friction stir welded Al-Zn-Mg-Cu alloy sheet were investigated by means of hardness and tensile tests, optical microscope and scanning electron microscope. The hardness profile of the weld exhibits a W shape with the lowest value in the thermo-mechanically affected zone on the advancing side. The tensile strength and elongation of the weld are about 71% and 72% that of the base material. In the nugget zone, there are a number of fine recrystallized grains and dispersed precipitates at grain boundaries. In the thermo-mechanically affected zone, the grain size is not uniform and there are a number of precipitates at grain boundaries. In the heat affected zone, the grain structure is similar to the base material.

Microstructure and mechanical properties of dissimilar friction stir welds of AA2014 and AA7075

2021 ◽  
pp. 095440892110581
Author(s):  
Raj Kumar ◽  
Vikas Upadhyay ◽  
Chaitanya Sharma
Keyword(s):  
Mechanical Properties ◽  
Process Parameters ◽  
Welding Speed ◽  
High Strength ◽  
Processing Parameters ◽  
Tensile Failure ◽  
Tensile Fracture ◽  
Hardness Profile ◽  
Friction Stir ◽  
Optical Micrograph

This work investigates the effect of process parameters on microstructure, mechanical properties, and fracture behavior of friction stir welded high-strength aluminum alloys AA2014-T6 and AA7075-T6. Optical micrograph, tensile property, and hardness profile of each weld were determined for analysis, and the tensile fracture surfaces were studied by scanning electron microscope. Welds microstructure were heterogeneous and displayed structures comprising of both base metals and the onion rings were seen in all welds except for the lowest heat input weld. Grains in the weld nugget zone were more refined on the retreating side than the other side. Asymmetric hardness profile had a distinct softened zone on each side whose location and softening extent varied with the processing parameters. Welding speed had a more significant effect on tensile strength than rotary speed and, drastically decreased the same. Faster welding speed formed microscopic defects and changed the appearance of fractured surfaces from flat to zigzag. The welds underwent ductile and mixed-mode tensile failure on the advancing side. Attainment of optimum combination of process parameters is imperative to yield defect-free stronger dissimilar welds

scholarly journals Surface Hardening of Aluminium Alloy with Addition of Zinc Particles by Friction Stir Processing

2020 ◽  
Vol 10 (1) ◽  
pp. 408-414
Author(s):  
Nurul Muhayat ◽  
Alvian Restu Putra Utama ◽  
Keyword(s):  
Mechanical Alloying ◽  
Physical Properties ◽  
Aluminium Alloy ◽  
Friction Stir Processing ◽  
Surface Hardening ◽  
Alloy Plate ◽  
Friction Stir ◽  
Material Hardness ◽  
Mechanical And Physical Properties ◽  
Uppermost Layer

AbstractMechanical alloying can be carried out by a method known as friction stir processing, whereby solid Zn particles in a solution are distributed onto an aluminium alloy plate. The aim of this study was to determine the effects of a volume of Zn particles on the mechanical and physical properties of aluminium 1xxx alloy that had been subjected to friction stir processing. The specimens were plates composed of 1xxx series aluminium. A groove, measuring 12 mm in diameter, was pierced to various depths, and the Zn particles in these containers were then subjected to friction stir processing using a pin-less tool with a diameter of 15 mm. The results showed that the highest hardness was found in the uppermost layer of the workpiece, and this gradually decreased with thickness. An increase in the amount of Zn particles caused an increase in material hardness. The highest hardness of 87.1 HV in the friction stir-processed AA1100 was obtained at the highest volume of Zn compared to the hardness of 44.5 HV, which was obtained for the specimen without the addition of Zn.

Procedure to find out the optimal ranges of process parameters for friction stir welding

2021 ◽  
pp. 146442072199314
Author(s):  
Shubham Verma ◽  
Joy Prakash Misra ◽  
Meenu Gupta
Keyword(s):  
Friction Stir Welding ◽  
Process Parameters ◽  
Tilt Angle ◽  
Welding Speed ◽  
Rotational Speed ◽  
Optical Microscope ◽  
Graphical Analysis ◽  
Friction Stir ◽  
Steepest Ascent ◽  
Vertical Milling Machine

The present study deals with the application of sequential procedure (i.e. steepest ascent) to obtain the optimum values of process parameters for conducting friction stir welding (FSW) experiments. A vertical milling machine is modified by fabricating fixture and tool ( H13 material) for performing FSW operation to join AA7039 plates. The steepest ascent technique is employed to design the experiments at different rotational speed, welding speed, and tilt angle. The ultimate tensile strength is considered as a performance characteristic for deciding the optimal levels. The mechanical and metallurgical characteristics of the joints are studied by executing tensile and microhardness tests. It is concluded from the graphical analysis of the steepest ascent technique that the optimal maximum and minimum values are 1812–1325 r/min for rotational speed, 43–26 mm/min for welding speed, and 2°–1.3° for tilt angle, respectively. Besides, optical microscope and scanning electron microscope are utilized for microstructural and fractographic analyses for a better understanding of the process.

A review on effect of processing parameters on mechanical properties of MMCs by friction stir process

2021 ◽  
Author(s):  
D. Prasuna Lilly Florence ◽  
P. H. V. Sesha Talpa Sai ◽  
S. Devaraj ◽  
K. S. Narayanaswamy
Keyword(s):  
Mechanical Properties ◽  
Processing Parameters ◽  
Friction Stir Process ◽  
Friction Stir

scholarly journals Development of an Additive Manufacturing System for the Deposition of Thermoplastics Impregnated with Carbon Fibers

2019 ◽  
Vol 3 (2) ◽  
pp. 35 ◽  
Author(s):  
Miguel Reis Silva ◽  
António M. Pereira ◽  
Nuno Alves ◽  
Gonçalo Mateus ◽  
Artur Mateus ◽  
...  
Keyword(s):  
Tensile Strength ◽  
Additive Manufacturing ◽  
Carbon Fibers ◽  
Low Cost ◽  
Deposition Process ◽  
Processing Parameters ◽  
Yarn Diameter ◽  
Thermoplastic Matrix ◽  
Anisotropic Mechanical Properties ◽  
Long Carbon Fiber

This work presents an innovative system that allows the oriented deposition of continuous fibers or long fibers, pre-impregnated or not, in a thermoplastic matrix. This system is used in an integrated way with the filamentary fusion additive manufacturing technology and allows a localized and oriented reinforcement of polymer components for advanced engineering applications at a low cost. To demonstrate the capabilities of the developed system, composite components of thermoplastic matrix (polyamide) reinforced with pre-impregnated long carbon fiber (carbon + polyamide), 1 K and 3 K, were processed and their tensile and flexural strength evaluated. It was demonstrated that the tensile strength value depends on the density of carbon fibers present in the composite, and that with the passage of 2 to 4 layers of fibers, an increase in breaking strength was obtained of about 366% and 325% for the 3 K and 1 K yarns, respectively. The increase of the fiber yarn diameter leads to higher values of tensile strength of the composite. The obtained standard deviation reveals that the deposition process gives rise to components with anisotropic mechanical properties and the need to optimize the processing parameters, especially those that lead to an increase in adhesion between deposited layers.

Additive Manufacturing of Glass

2014 ◽  
Vol 136 (6) ◽  
Author(s):  
Junjie Luo ◽  
Heng Pan ◽  
Edward C. Kinzel
Keyword(s):  
Additive Manufacturing ◽  
Glass Powder ◽  
Processing Parameters ◽  
Gradient Index ◽  
Continuous Line ◽  
Single Track ◽  
Laser Melting ◽  
Powder Bed ◽  
Transparent Parts ◽  
Insight Into

Selective laser melting (SLM) is a technique for the additive manufacturing (AM) of metals, plastics, and even ceramics. This paper explores using SLM for depositing glass structures. A CO2 laser is used to locally melt portions of a powder bed to study the effects of process parameters on stationary particle formation as well as continuous line quality. Numerical modeling is also applied to gain insight into the physical process. The experimental and numerical results indicate that the absorptivity of the glass powder is nearly constant with respect to the processing parameters. These results are used to deposit layered single-track wide walls to demonstrate the potential of using the SLM process for building transparent parts. Finally, the powder bed process is compared to a wire-fed approach. AM of glass is relevant for gradient index optics, systems with embedded optics, and the formation of hermetic seals.

Sign in / Sign up

Export Citation Format

Share Document