scholarly journals Easily Sinterable Low-Alloy Steel Powders for P/M Diamond Tools

Metals ◽  
2021 ◽  
Vol 11 (8) ◽  
pp. 1204
Author(s):  
Janusz Konstanty ◽  
Dorota Tyrala
Keyword(s):  
Alloy Steel ◽  
Theoretical Density ◽  
Low Alloy Steel ◽  
Closed Porosity ◽  
Iron Base ◽  
Temperature Range ◽  
Wire Saw ◽  
Conventional Press ◽  
Thermocalc Software ◽  
Matrix Hardness

The work presents the design and fabrication procedures used to manufacture inexpensive iron-base powders employed as a matrix in diamond-impregnated tool components. Three newly developed low alloy steel powders, containing from 94.4 to 99.4 wt.% Fe, have been formulated with the assistance of ThermoCalc software and produced by means of a proprietary process patented by AGH-UST. It has been shown that the powders are readily pressureless sintered to a closed porosity condition (>95% theoretical density) at a temperature range between 840 and 950 °C. All as-consolidated materials achieve the desired tool matrix hardness of more than 200 HV. One of the experimental powders has been designed to partly melt within the sintering window. This is particularly important in fabrication of wire saw beads by the conventional press and sinter route because sintering of a diamond-impregnated ring and its further brazing to a tubular steel holder can be combined into one operation.

scholarly journals A Newly Developed Easily Sinterable Low-Alloy Steel Powder

Materials ◽  
2021 ◽  
Vol 14 (2) ◽  
pp. 406
Author(s):  
Dorota Tyrala ◽  
Janusz Konstanty ◽  
Izabela Kalemba-Rec
Keyword(s):  
Mechanical Strength ◽  
Alloy Steel ◽  
Sintering Temperature ◽  
Steel Powder ◽  
Low Alloy Steel ◽  
Closed Porosity ◽  
Cold Forming ◽  
The Matrix ◽  
Sintered Diamond ◽  
Iron Based

The work presents a possibility of fabrication of inexpensive iron-based powders intended to form the matrix in sintered diamond-impregnated tool components. In this study, a finely dispersed, pre-alloyed steel powder, containing over 95 wt.% Fe, has been designed and fabricated by means of a proprietary process developed at AGH-University of Science & Technology. It has been shown that the experimental powder can be consolidated to a closed porosity condition (>95% theoretical density) by pressure-less sintering at a temperature below 900 °C. The as-consolidated material is characterized by an excellent combination of hardness (~250 HV) and mechanical strength (>1200 MPa in 3-point bending) that meets the diamond tooling requirements. Its properties can be modified to some extent by varying the cold forming pressure and sintering temperature.

Effect of high temperatures on mechanical properties of seam metal of low-carbon low-alloy steel welded joint

2021 ◽  
pp. 33-38
Author(s):  
S. A. Nikulin ◽  
◽  
S. O Rogachev ◽  
V. A. Belov ◽  
V. Yu. Turilina ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Comparative Analysis ◽  
Alloy Steel ◽  
Room Temperature ◽  
Weld Seam ◽  
Welded Joint ◽  
Low Carbon ◽  
Low Alloy Steel ◽  
Plastic Properties ◽  
Temperature Range

The mechanical properties of the seam metal of a low-carbon low-alloy steel welded joint of the 22K type (Russian standard) have been investigated when testing for uniaxial tension in the temperature range from room temperature to 1200 °C. A comparative analysis of the changes in the structure, the strength and plastic properties of base metal and weld seam metal in the selected temperature range was carried out.

On Corrosion Resistance Of Austenitic Stainless Steel Clad Layer on a Low Alloy Steel

2018 ◽  
Vol 32 (3) ◽  
pp. 20
Author(s):  
Manas Kumar Saha ◽  
Ritesh Hazra ◽  
Ajit Mondal ◽  
Santanu Das
Keyword(s):  
Stainless Steel ◽  
Corrosion Resistance ◽  
Austenitic Stainless Steel ◽  
Alloy Steel ◽  
Low Alloy Steel ◽  
Clad Layer

Hot deformation simulation of modified AISI 5120 low alloy steel

2017 ◽  
Author(s):  
Diego Boschetti ◽  
Ana Paola Braga ◽  
Paula Fernanda da Silva Farina
Keyword(s):  
Alloy Steel ◽  
Hot Deformation ◽  
Low Alloy Steel ◽  
Deformation Simulation

ANCORSTEEL 30 HP

Alloy Digest ◽  
2009 ◽  
Vol 58 (12) ◽  
Keyword(s):  
Physical Properties ◽  
Tensile Properties ◽  
Alloy Steel ◽  
Steel Powder ◽  
Heat Treating ◽  
Powder Alloy ◽  
Low Alloy Steel ◽  
Powder Metal

Abstract Ancorsteel 30 HP is a prealloyed low-alloy steel powder alloy with moderate hardenability. This datasheet provides information on composition, physical properties, hardness, and tensile properties. It also includes information on heat treating and powder metal forms. Filing Code: CS-151. Producer or source: Hoeganaes Corporation.

TENFORM XF450

Alloy Digest ◽  
2007 ◽  
Vol 56 (1) ◽  
Keyword(s):  
Physical Properties ◽  
Tensile Properties ◽  
Alloy Steel ◽  
High Strength ◽  
Bend Strength ◽  
Low Alloy Steel ◽  
Hot Rolled

Abstract The high strength of Tenform XF450, a hot-rolled high-strength low-alloy steel, allows the user to increase the strength of a finished component or to reduce the thickness. The steel is used in the construction and the automotive industries. This datasheet provides information on composition, physical properties, tensile properties. and bend strength. It also includes information on forming. Filing Code: CS-148. Producer or source: Hille & Mueller, USA Inc. See also Alloy Digest CS-173, November 2012.

USS AR 360

Alloy Digest ◽  
1977 ◽  
Vol 26 (5) ◽  
Keyword(s):  
United States ◽  
Corrosion Resistance ◽  
Surface Treatment ◽  
Tensile Properties ◽  
Alloy Steel ◽  
Heat Treating ◽  
Low Alloy Steel ◽  
Materials Handling ◽  
United States Steel Corporation ◽  
Major Consideration

Abstract USS AR 360 is a quenched-and-tempered low-alloy steel designed to fit a broad range of applications where resistance to abrasion is a major consideration. It is used to produce components for mining and materials handling equipment and agricultural implements. This datasheet provides information on composition, hardness, and tensile properties. It also includes information on corrosion resistance as well as forming, heat treating, joining, and surface treatment. Filing Code: SA-332. Producer or source: United States Steel Corporation.

Sign in / Sign up

Export Citation Format

Share Document