scholarly journals Property Improvement of Additively Manufactured Ti64 by Heat Treatment Characterized by In Situ High Temperature EBSD and Neutron Diffraction

Metals ◽  
2021 ◽  
Vol 11 (10) ◽  
pp. 1661
Author(s):  
Shigehiro Takajo ◽  
Toshiro Tomida ◽  
El’ad N. Caspi ◽  
Asaf Pesach ◽  
Eitan Tiferet ◽  
...  
Keyword(s):  
Heat Treatment ◽  
Phase Transformation ◽  
High Temperature ◽  
Grain Boundaries ◽  
Beta Phase ◽  
Powder Materials ◽  
Layer By Layer ◽  
Slow Cooling ◽  
Α Phase

Among various off-equilibrium microstructures of additively manufactured Ti-6Al-4V alloy, electron beam powder bed fusion, in which three dimensional metallic objects are fabricated by melting the ingredient powder materials layer by layer on a pre-heated bed, results in a specimen that is nearly free of the preferred orientation of the α-Ti phase as well as a low beta phase fraction of ∼1 wt%. However, when further heat treatment of up to 1050 ∘C was applied to the material in our previous study, a strong texture aligning the hexagonal basal plane of α phase with the build direction and about 6% β phase appeared at room temperature. In this study, to understand the mechanism of this heat treatment, the grain level microstructure of the additively manufactured Ti-6Al-4V was investigated using in situ high temperature EBSD up to 1000 ∘C, which allows the tracking of individual grains during a heat cycle. As a result, we found a random texture originating from the fine grains in the initial material and observed a significant suppression of α phase nucleation in the slow cooling after heating to 950 ∘C within the α and β dual phase regime but close to the the β-transus temperature at ∼980 ∘C, which led to a coarse microstructure. Furthermore, the texture resulting from phase transformation of the additively manufactured Ti-6Al-4V assuming nucleation at the grain boundaries was modeled, using the double Burgers orientation relationship for the first time. The model successfully reproduced the measured texture, suggesting that the texture enhancement of the α phase by the additional heat treatment derives also from the variant selection during the phase transformation and nucleation on grain boundaries.

scholarly journals Investigation of the α−γ−α Phase Transformation in Steel: High-Temperature In Situ EBSD Measurements

2008 ◽  
Vol 2008 ◽  
pp. 1-7 ◽  
Author(s):  
I. Lischewski ◽  
D. M. Kirch ◽  
A. Ziemons ◽  
G. Gottstein
Keyword(s):  
Phase Transformation ◽  
High Temperature ◽  
Electron Backscatter Diffraction ◽  
Experimental Setup ◽  
Ebsd Data ◽  
Α Phase ◽  
Electron Backscatter ◽  
First Results ◽  
Backscatter Diffraction

A newly developed laser powered heating stage for commercial SEMs in combination with automated established electron backscatter diffraction (EBSD) data acquisition is presented. This novel experimental setup can be used to achieve more information about microstructure and orientation changes during grain growth, recrystallization, recovery, and phase transformations. First results on the α−γ−α phase transformation in steel within 886∘C–900∘C are presented.

scholarly journals Additive Manufacturing of Ti-Based Intermetallic Alloys: A Review and Conceptualization of a Next-Generation Machine

Materials ◽  
2021 ◽  
Vol 14 (15) ◽  
pp. 4317
Author(s):  
Thywill Cephas Dzogbewu ◽  
Willie Bouwer du Preez
Keyword(s):  
Heat Treatment ◽  
High Temperature ◽  
Additive Manufacturing ◽  
Complex Geometries ◽  
Intermetallic Alloys ◽  
Tial Alloys ◽  
Conventional Methods ◽  
Manufacturing Technologies ◽  
In Situ Heat Treatment

TiAl-based intermetallic alloys have come to the fore as the preferred alloys for high-temperature applications. Conventional methods (casting, forging, sheet forming, extrusion, etc.) have been applied to produce TiAl intermetallic alloys. However, the inherent limitations of conventional methods do not permit the production of the TiAl alloys with intricate geometries. Additive manufacturing technologies such as electron beam melting (EBM) and laser powder bed fusion (LPBF), were used to produce TiAl alloys with complex geometries. EBM technology can produce crack-free TiAl components but lacks geometrical accuracy. LPBF technology has great geometrical precision that could be used to produce TiAl alloys with tailored complex geometries, but cannot produce crack-free TiAl components. To satisfy the current industrial requirement of producing crack-free TiAl alloys with tailored geometries, the paper proposes a new heating model for the LPBF manufacturing process. The model could maintain even temperature between the solidified and subsequent layers, reducing temperature gradients (residual stress), which could eliminate crack formation. The new conceptualized model also opens a window for in situ heat treatment of the built samples to obtain the desired TiAl (γ-phase) and Ti3Al (α2-phase) intermetallic phases for high-temperature operations. In situ heat treatment would also improve the homogeneity of the microstructure of LPBF manufactured samples.

Analyses of Eutectoid Phase Transformations in Nb–SilicideIn SituComposites

2004 ◽  
Vol 10 (4) ◽  
pp. 470-480 ◽  
Author(s):  
B.P. Bewlay ◽  
S.D. Sitzman ◽  
L.N. Brewer ◽  
M.R. Jackson
Keyword(s):  
Crystal Structure ◽  
Phase Transformation ◽  
High Temperature ◽  
Room Temperature ◽  
Bulk Composition ◽  
High Strength ◽  
Eutectoid Decomposition ◽  
Quaternary Alloys ◽  
Temperature Fracture

Nb–silicide in situ composites have great potential for high-temperature turbine applications. Nb–silicide composites consist of a ductile Nb-based solid solution together with high-strength silicides, such as Nb5Si3and Nb3Si. With the appropriate addition of alloying elements, such as Ti, Hf, Cr, and Al, it is possible to achieve a promising balance of room-temperature fracture toughness, high-temperature creep performance, and oxidation resistance. In Nb–silicide composites generated from metal-rich binary Nb-Si alloys, Nb3Si is unstable and experiences eutectoid decomposition to Nb and Nb5Si3. At high Ti concentrations, Nb3Si is stabilized to room temperature, and the eutectoid decomposition is suppressed. However, the effect of both Ti and Hf additions in quaternary alloys has not been investigated previously. The present article describes the discovery of a low-temperature eutectoid phase transformation during which (Nb)3Si decomposes into (Nb) and (Nb)5Si3, where the (Nb)5Si3possesses the hP16 crystal structure, as opposed to the tI32 crystal structure observed in binary Nb5Si3. The Ti and Hf concentrations were adjusted over the ranges of 21 to 33 (at.%) and 7.5 to 33 (at.%) to understand the effect of bulk composition on the phases present and the eutectoid phase transformation.

Effect of Hot Processing on Mircrostructure and Properties of Flat Billets of TA15 Titanium Alloy

2021 ◽  
Vol 1016 ◽  
pp. 906-910
Author(s):  
Xin Hua Min ◽  
Cheng Jin
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Titanium Alloy ◽  
High Temperature ◽  
Room Temperature ◽  
High Strength ◽  
Slow Cooling ◽  
Microstructure And Mechanical Properties ◽  
Ta15 Titanium Alloy ◽  
The Ideal

In this paper,effect of the different forging processes on the microstructure and mechanical properties of the flat flat billets of TA15 titanium alloy was investigated.The flat billiets of 80 mm×150 mm×L sizes of TA15 titanium alloy are produced by four different forging processes.Then the different microstrure and properties of the flat billiets were obtained by heat treatment of 800 °C~850 °C×1 h~4h.The results show that, adopting the first forging temperature at T1 °C、slow cooling and the second forging temperature at T2°C 、quick cooling, the primary αphases content is just 10%, and there are lots of thin aciculate phases on the base. This microstructure has both high strength at room temperature and high temperature, while the properties between the cross and lengthwise directions are just the same. So the hot processing of the first forging temperature at T1 °C、slow cooling and the second forging temperature at T2°C 、quick cooling is choosed as the ideal processing for production of aircraft frame parts.

scholarly journals Formation of Large Size Precipitate-Free Zones in β Annealing of the Near-β Ti-55531 Titanium Alloy

Metals ◽  
2019 ◽  
Vol 9 (5) ◽  
pp. 544 ◽  
Author(s):  
Xueqi Jiang ◽  
Xiaoqiang Shi ◽  
Xiaoguang Fan ◽  
Qi Li
Keyword(s):  
Titanium Alloy ◽  
Phase Transformation ◽  
Heterogeneous Nucleation ◽  
Isothermal Heat Treatment ◽  
Precipitate Free Zone ◽  
Mode Iii ◽  
Slow Cooling ◽  
Free Zone ◽  
Large Size ◽  
Α Phase

Large size (>10000 μm2) precipitate-free zones in the absence of microsegregation were observed in the near-β Ti-55531 titanium alloy after furnace cooling from high temperature and longtime annealing in the single-β phase field. To reveal the formation mechanism of the large size precipitate-free zone, continuous cooling and isothermal heat treatment were carried out to investigate the β-α phase transformation process. It was found that the large size precipitate free zone is attributed to the heterogeneous nucleation of α phase. The nucleation site evolves in three different modes: I-random nucleation inside the β grain, II-network nucleation inside the β grain and, III-heterogeneous nucleation on the precipitated α phase. Modes I and II lead to homogeneous transformed structure while Mode III results in the large size precipitate-free zone. Both modes II and III are promoted at high annealing temperature, rapid cooling above 600 °C or slow cooling below 600 °C. Mode II is common as it can minimize the strain energy in phase transformation. As a result, the formation of the large size precipitate-free zone is not deterministic.

Effect of Deposition Conditions on Intrinsic Stress, Phase Transformation and Stress Relaxation in Tantalum Thin Films

1991 ◽  
Vol 239 ◽  
Author(s):  
A. Mutscheller ◽  
L. A. Clevenger ◽  
J.M.E. Harper ◽  
C. Cabrai ◽  
K. Barmakt
Keyword(s):  
Thin Films ◽  
Phase Transition ◽  
Phase Transformation ◽  
Stress Relaxation ◽  
Compressive Stress ◽  
Stress Relief ◽  
Beta Phase ◽  
Alpha Phase ◽  
Intrinsic Stress

AbstractWe demonstrate that the high temperature polymorphic tantalum phase transition from the tetragonal beta phase to the cubic alpha phase causes complete stress relaxation and a large decrease in the resistance of tantalum thin films. 100 nm beta tantalum thin films were deposited onto thermally oxidized <100> silicon wafers by dc magnetron sputtering with argon. In situ stress and resistance at temperature were measured during temperature-ramped annealing in purified He. Upon heating, films that were initially compressively stressed showed increasing compressive stress due to thermo-elastic deformation from 25 to 550°C, slight stress relief due to plastic deformation from 550 to 700°C and complete stress relief due to the beta to alpha phase transformation at approximately 700–800°C. Incomplete compressive stress relaxation was observed at high temperatures if the film was initially deposited in the alpha phase or if the beta phase did not completely transform into alpha by 800°C. This incomplete beta to alpha phase transition was most commonly observed on samples that had radio frequency substrate bias greater than -100 V. We conclude that the main stress relief mechanism for tantalum thin films is the beta to alpha phase transformation that occurs at 700 to 800°C.

Formation of a Novel X Phase in Mg–Gd–Zn–Zr Alloy

2010 ◽  
Vol 654-656 ◽  
pp. 623-626 ◽  
Author(s):  
Y.J. Wu ◽  
Li Ming Peng ◽  
X.Q. Zeng ◽  
D.L. Lin ◽  
W.J. Ding
Keyword(s):  
Heat Treatment ◽  
Solid Solution ◽  
Phase Transformation ◽  
Grain Boundaries ◽  
Solution Heat Treatment ◽  
Long Period ◽  
Β Phase ◽  
Lpso Structure ◽  
Zr Alloy ◽  
Zr Alloys

The coherent fine-lamellae consisting of the 2H-Mg and the 14H-type long period stacking ordered (LPSO) structure within α'-Mg matrix have been observed in an as-cast Mg–Gd–Zn–Zr alloy. During subsequent solid solution heat treatment at 773 K, in addition to the lamellae within matrix, a novel lamellar X phase [Mg–(8.37±1.0)Zn–(11.32±1.0)Gd] with the 14H-type LPSO structure was transformed from the dendritical β phase. The 14H-type LPSO structure existing in Mg–Gd–Zn–Zr alloys derives from two variant ways: formation of the 14H-type LPSO structure comes from two variant means: i.e., the formation within matrix and the phase transformation from the β phase to the X phase in grain boundaries.

Sign in / Sign up

Export Citation Format

Share Document