scholarly journals Research on the Application of MWCNTs/PLA Composite Material in the Manufacturing of Conductive Composite Products in 3D Printing

Micromachines ◽  
2018 ◽  
Vol 9 (12) ◽  
pp. 635 ◽  
Author(s):  
Jinjie Luo ◽  
Haibao Wang ◽  
Duquan Zuo ◽  
Anping Ji ◽  
Yaowen Liu
Keyword(s):  
Composite Material ◽  
3D Printing ◽  
Fused Deposition Modeling ◽  
Three Dimensional ◽  
Poly Lactic Acid ◽  
Melt Flow Rate ◽  
Conductive Composites ◽  
Fused Deposition ◽  
Multi Walled Carbon Nanotubes ◽  
Walled Carbon Nanotubes

As an advanced manufacturing technology that has been developed in recent years, three-dimensional (3D) printing of macromolecular materials can create complex-shaped components that cannot be realized by traditional processing. However, only a few types of macromolecular materials are suitable for 3D printing: the structure must have a single function, and manufacturing macromolecular functional devices is difficult. In this study, using poly lactic acid (PLA) as a matrix, conductive composites were prepared by adding various contents of multi-walled carbon nanotubes (MWCNTs). The printability and properties of MWCNT/PLA composites with different MWCNT proportions were studied by using the fused deposition modeling (FDM) processing technology of 3D printing. The experimental results showed that high conductivity can be realized in 3D-printed products with a composite material containing 5% MWCNTs; its conductivity was 0.4 ± 0.2 S/cm, its tensile strength was 78.4 ± 12.4 MPa, and its elongation at break was 94.4% ± 14.3%. It had a good melt flow rate and thermal properties, and it enabled smooth printing, thus meeting all the requirements for the 3D printing of consumables.

scholarly journals Preparation and Characterization of 3D Printed PLA-Based Conductive Composites Using Carbonaceous Fillers by Masterbatch Melting Method

Polymers ◽  
2019 ◽  
Vol 11 (10) ◽  
pp. 1589 ◽  
Author(s):  
Rui Guo ◽  
Zechun Ren ◽  
Xin Jia ◽  
Hongjie Bi ◽  
Haiying Yang ◽  
...  
Keyword(s):  
Fused Deposition Modeling ◽  
Sodium Dodecylbenzene Sulfonate ◽  
Melting Method ◽  
Conductive Composites ◽  
Fused Deposition ◽  
Dodecylbenzene Sulfonate ◽  
Interfacial Compatibility ◽  
Multi Walled Carbon Nanotubes ◽  
Deposition Modeling ◽  
Walled Carbon Nanotubes

This study was aimed at improving the conductivity of polylactic acid (PLA)-based composites by incorporating carbonaceous fillers. The composites with the addition of graphene nanoplatelets (rGO) or multi-walled carbon nanotubes (MWCNTs) were fabricated by the masterbatch melting method in order to improve the dispersion of the two kinds of nano-fillers. The results showed that, with the addition of 9 wt % rGO, the volume electrical resistivity of the composite reached the minimum electrical resistance of 103 Ω·m, at which point the conductive network in the composites was completely formed. The interfacial compatibility, apparent viscosity, and the thermal stability of the composite were also good. The rGO functionalized by sodium dodecylbenzene sulfonate (SDBS) was an efficient method to further improve the electrical conductivity of the composite, compared with tannic acid and MWCNTs. The resistivity was reduced by an order in magnitude. Patterns printed onto different baseplates by fused deposition modeling illustrated that the functionalized composite had certain flexibility and it is suitable for printing complex shapes.

scholarly journals Impact of Aging Effect and Heat Treatment on the Tensile Properties of PLA (Poly Lactic Acid) Printed Parts

2020 ◽  
Vol 57 (3) ◽  
pp. 147-159
Author(s):  
Mohammad Sakib Hasan ◽  
Toni Ivanov ◽  
Milos Vorkapic ◽  
Aleksandar Simonovic ◽  
David Daou ◽  
...  
Keyword(s):  
Heat Treatment ◽  
3D Printing ◽  
Tensile Properties ◽  
Fused Deposition Modeling ◽  
Three Dimensional ◽  
Aging Effect ◽  
Poly Lactic Acid ◽  
Layer Height ◽  
Fused Deposition ◽  
Deposition Modeling

Rapid innovations in 3D printing technology have allowed highly complex parts to be manufactured quickly and easily, particularly for prototyping purposes. Fused Deposition Modeling of thermoplastic materials is one of the most commonly used techniques in three-dimensional (3D) printing. The major aim of Fused Deposition Modeling (FDM) is to design and manufacture usable parts for fields such as engineering and medicine. Therefore, it is essential to investigate the mechanical properties of such FDM processed structures. One of the most commonly used materials currently on the market is Polylactic Acid (PLA). The main purpose of this paper is to investigate the effects of aging and heat treatment on the tensile properties of PLA printed test specimens. The tensile properties of parts manufactured by the 3D printer are influenced by various parameters such as extrusion temperature, infill density, building direction, layer height, etc. A total of 96 specimens were built by altering building orientation and layer height to estimate and compare the tensile properties of the printed parts. To investigate the aging effect, 30 of 96 specimens were printed 6 months before the tensile experiment. Half of both aged and new specimens were cured in an oven at 57.5 [�ŞC] for 3 hours while the other half endured no heat treatment. After the performed measurement, it can be concluded that heat treatment generally improves structural strength of the printed parts, while aging decreases it. However, these effects are highly dependent on the layer thickness and printing quality. The tensile test is conducted according to the ASTM D638 standard. The fractured samples were further characterized using an electron microscope.

Development of three-dimensional printing filaments based on poly(lactic acid)/hydroxyapatite composites with potential for tissue engineering

2021 ◽  
pp. 002199832098856
Author(s):  
Marcela Piassi Bernardo ◽  
Bruna Cristina Rodrigues da Silva ◽  
Luiz Henrique Capparelli Mattoso
Keyword(s):  
Tissue Engineering ◽  
Lactic Acid ◽  
Fused Deposition Modeling ◽  
Three Dimensional ◽  
Poly Lactic Acid ◽  
Scanning Calorimetry ◽  
Three Dimensional Printing ◽  
Fused Deposition ◽  
Deposition Modeling ◽  
3D Printed

Injured bone tissues can be healed with scaffolds, which could be manufactured using the fused deposition modeling (FDM) strategy. Poly(lactic acid) (PLA) is one of the most biocompatible polymers suitable for FDM, while hydroxyapatite (HA) could improve the bioactivity of scaffold due to its chemical composition. Therefore, the combination of PLA/HA can create composite filaments adequate for FDM and with high osteoconductive and osteointegration potentials. In this work, we proposed a different approache to improve the potential bioactivity of 3D printed scaffolds for bone tissue engineering by increasing the HA loading (20-30%) in the PLA composite filaments. Two routes were investigated regarding the use of solvents in the filament production. To assess the suitability of the FDM-3D printing process, and the influence of the HA content on the polymer matrix, thermogravimetric analysis (TGA), differential scanning calorimetry (DSC) and scanning electron microscopy (SEM) were performed. The HA phase content of the composite filaments agreed with the initial composite proportions. The wettability of the 3D printed scaffolds was also increased. It was shown a greener route for obtaining composite filaments that generate scaffolds with properties similar to those obtained by the solvent casting, with high HA content and great potential to be used as a bone graft.

scholarly journals Mesh-Type Three-Dimensional (3D) Printing of Human Organs and Tumors: Fast, Cost-Effective, and Personalized Anatomic Modeling of Patient-Oriented Visual Aids

2021 ◽  
Vol 11 (3) ◽  
pp. 1047
Author(s):  
Jungirl Seok ◽  
Sungmin Yoon ◽  
Chang Hwan Ryu ◽  
Junsun Ryu ◽  
Seok-ki Kim ◽  
...  
Keyword(s):  
3D Printing ◽  
3D Modeling ◽  
Fused Deposition Modeling ◽  
Three Dimensional ◽  
Tumor Location ◽  
Visual Aids ◽  
Surgical Specimen ◽  
Personalized Care ◽  
Fused Deposition ◽  
Mesh Work

Although three-dimensional (3D)-printed anatomic models are not new to medicine, the high costs and lengthy production times entailed have limited their application. Our goal was developing a new and less costly 3D modeling method to depict organ-tumor relations at faster printing speeds. We have devised a method of 3D modeling using tomographic images. Coordinates are extracted at a specified interval, connecting them to create mesh-work replicas. Adjacent constructs are depicted by density variations, showing anatomic targets (i.e., tumors) in contrasting colors. An array of organ solid-tumor models was printed via a Fused Deposition Modeling 3D printer at significantly less cost ($0.05/cm3) and time expenditure (1.73 min/cm3; both, p < 0.001). Printed models helped promote visual appreciation of organ-tumor anatomy and adjacent tissues. Our mesh-work 3D thyroidal prototype reproduced glandular size/contour and tumor location, readily approximating the surgical specimen. This newly devised mesh-type 3D printing method may facilitate anatomic modeling for personalized care and improve patient awareness during informed surgical consent.

scholarly journals Cellulose Nanofibrils Filled Poly(Lactic Acid) Biocomposite Filament for FDM 3D Printing

Molecules ◽  
2020 ◽  
Vol 25 (10) ◽  
pp. 2319 ◽  
Author(s):  
Qianqian Wang ◽  
Chencheng Ji ◽  
Lushan Sun ◽  
Jianzhong Sun ◽  
Jun Liu
Keyword(s):  
Thermal Stability ◽  
3D Printing ◽  
Fused Deposition Modeling ◽  
Mechanical Performance ◽  
Cellulose Nanofibrils ◽  
Poly Lactic Acid ◽  
Fused Deposition ◽  
Wide Range ◽  
The Matrix ◽  
Direct Digital Manufacturing

As direct digital manufacturing, 3D printing (3DP) technology provides new development directions and opportunities for the high-value utilization of a wide range of biological materials. Cellulose nanofibrils (CNF) and polylactic acid (PLA) biocomposite filaments for fused deposition modeling (FDM) 3DP were developed in this study. Firstly, CNF was isolated by enzymatic hydrolysis combined with high-pressure homogenization. CNF/PLA filaments were then prepared by melt-extrusion of PLA as the matrix and CNF as the filler. Thermal stability, mechanical performance, and water absorption property of biocomposite filaments and 3D-printed objects were analyzed. Findings showed that CNF increased the thermal stability of the PLA/PEG600/CNF composite. Compared to unfilled PLA FDM filaments, the CNF filled PLA biocomposite filament showed an increase of 33% in tensile strength and 19% in elongation at break, suggesting better compatibility for desktop FDM 3DP. This study provided a new potential for the high-value utilization of CNF in 3DP in consumer product applications.

Optical Humidity Sensor Based on Tapered Fiber with Multi-walled Carbon Nanotubes Slurry

2017 ◽  
Vol 6 (1) ◽  
pp. 97 ◽  
Author(s):  
Habibah Mohamed ◽  
Ninik Irawati ◽  
Fauzan Ahmad ◽  
Mohd Haniff Ibrahim ◽  
Sumiaty Ambran ◽  
...  
Keyword(s):  
Carbon Nanotubes ◽  
Humidity Sensor ◽  
Fused Deposition Modeling ◽  
Acrylonitrile Butadiene Styrene ◽  
Performance Comparison ◽  
Tapered Fiber ◽  
Fused Deposition ◽  
Multi Walled Carbon Nanotubes ◽  
Deposition Modeling ◽  
Walled Carbon Nanotubes

<p>We demonstrated performance comparison of optical humidity sensor for bare and Multi-walled carbon nanotubes (MWCNTs) slurry coated tapered optical fiber. The starting material for MWCNTs slurry is MWCNTs- acrylonitrile butadiene styrene (ABS) based fused deposition modeling (FDM) 3D printer filament. The ABS was dissolved using acetone to produce MWCNTs-acetone suspension. The MWCNTs-acetone suspension was drop-casted on the tapered fiber to produce MWCNTs slurry by evaporation process at room temperature, which resulted the MWCNTs slurry attach to the tapered fiber. The MWCNTs slurry acts as the cladding for humidity changes measurement. The experimental works showed improvement of sensitivity from 3.811 μW/% of bare tapered fiber to 5.17 μW/% for the coated tapered fiber with MWCNTs slurry when the humidity varied from 45% to 80%.</p>

A Heuristic Scaling Strategy for Multi-Robot Cooperative Three-Dimensional Printing

2020 ◽  
Vol 20 (4) ◽  
Author(s):  
Laxmi Poudel ◽  
Chandler Blair ◽  
Jace McPherson ◽  
Zhenghui Sha ◽  
Wenchao Zhou
Keyword(s):  
3D Printing ◽  
Fused Deposition Modeling ◽  
Three Dimensional ◽  
Evaluation Framework ◽  
Geometric Constraints ◽  
Mathematical Representation ◽  
Printing Process ◽  
Fused Deposition ◽  
3D Printers ◽  
Printing Time

Abstract While three-dimensional (3D) printing has been making significant strides over the past decades, it still trails behind mainstream manufacturing due to its lack of scalability in both print size and print speed. Cooperative 3D printing (C3DP) is an emerging technology that holds the promise to mitigate both of these issues by having a swarm of printhead-carrying mobile robots working together to finish a single print job cooperatively. In our previous work, we have developed a chunk-based printing strategy to enable the cooperative 3D printing with two fused deposition modeling (FDM) mobile 3D printers, which allows each of them to print one chunk at a time without interfering with the other and the printed part. In this paper, we present a novel method in discretizing the continuous 3D printing process, where the desired part is discretized into chunks, resulting in multi-stage 3D printing process. In addition, the key contribution of this study is the first working scaling strategy for cooperative 3D printing based on simple heuristics, called scalable parallel arrays of robots for 3DP (SPAR3), which enables many mobile 3D printers to work together to reduce the total printing time for large prints. In order to evaluate the performance of the printing strategy, a framework is developed based on directed dependency tree (DDT), which provides a mathematical and graphical description of dependency relationships and sequence of printing tasks. The graph-based framework can be used to estimate the total print time for a given print strategy. Along with the time evaluation metric, the developed framework provides us with a mathematical representation of geometric constraints that are temporospatially dynamic and need to be satisfied in order to achieve collision-free printing for any C3DP strategy. The DDT-based evaluation framework is then used to evaluate the proposed SPAR3 strategy. The results validate the SPAR3 as a collision-free strategy that can significantly shorten the printing time (about 11 times faster with 16 robots for the demonstrated examples) in comparison with the traditional 3D printing with single printhead.

scholarly journals Proper Blends of Biodegradable Polycaprolactone and Natural Rubber for 3D Printing

Polymers ◽  
2020 ◽  
Vol 12 (10) ◽  
pp. 2416
Author(s):  
Thossapit Wissamitanan ◽  
Charoenyutr Dechwayukul ◽  
Ekwipoo Kalkornsurapranee ◽  
Wiriya Thongruang
Keyword(s):  
Mechanical Properties ◽  
3D Printing ◽  
Natural Rubber ◽  
Shape Recovery ◽  
Fused Deposition Modeling ◽  
Melt Flow ◽  
Melt Flow Rate ◽  
Fused Deposition ◽  
Compression Set ◽  
Deposition Modeling

Flexible thermoplastic elastomers (TPE) were prepared for fused deposition modeling (FDM) or 3D printing. These materials can be used for medical purposes such as disposable soft splints and other flexible devices. Blends of 50% epoxidized natural rubber (ENR-50) and block rubber (Standard Thai Rubber 5L (STR5L)) with polycaprolactone (PCL) were produced and compared. The purpose of this study was to investigate the properties of natural rubber (NR) and PCL in simple blends with PCL contents of 40%, 50%, and 60% by weight (except at 75% for morphology study) in the base mixture (NR/PCL). The significant flow factors for FDM materials, such as melting temperature (Tm) and melt flow rate (MFR), were observed by differential scanning calorimetry (DSC) and via the melt flow index (MFI). In addition, the following mechanical properties were also determined: tensile strength, compression set, and hardness. The results from DSC showed that the melting temperature changed slightly (1–2 °C) with amount of PCL used, and there was a suspicious point in the 50/50 blends with both types of rubber. The lowest melting enthalpy of both blends was found at the 50/50 blended composition. The MFI results showed that PCL significantly affected the melt flow rate of both blends. The ENR-50/PCL blend flowed better than the STR5L/PCL blend. The conclusion was that this was due to the morphology of its phase structure having better uniformity than that of the STR5L/PCL blend. In compression set testing or measuring shape recovery, rubber directly influenced the recovery in all blends. The ENR-50/PCL blend had less recovery than the STR5L/PCL blend, probably due to the functional effects of epoxide groups and polarity mismatch. The hard phase PCL significantly affected the hardness of samples but improved shape recovery of the material. The ENR-50/PCL blend had better tensile properties than the STR5L/PCL blend. The elongation at break of both blends improved with a high rubber content. Hence, the ENR-50/PCL blend was superior to STR5L/PCL for printing purposes due to its better miscibility, uniformity, and flow, which are the keys to success for optimizing the fused deposition modeling conditions as well as the overall mechanical properties of products. Most blends in this study were only slightly different, but the 50/50 blend of ENR-50/PCL seemed to be near optimal for 3D printing.

Sign in / Sign up

Export Citation Format

Share Document