scholarly journals Three-Dimensional Technology Applications in Maxillofacial Reconstructive Surgery: Current Surgical Implications

Nanomaterials ◽  
2020 ◽  
Vol 10 (12) ◽  
pp. 2523
Author(s):  
Yasmin Ghantous ◽  
Aysar Nashef ◽  
Aladdin Mohanna ◽  
Imad Abu-El-naaj
Keyword(s):  
3D Printing ◽  
Head And Neck ◽  
Donor Site ◽  
Maxillofacial Surgery ◽  
Three Dimensional ◽  
Oral And Maxillofacial Surgery ◽  
3D Technology ◽  
Printing Technology ◽  
Reconstructive Procedures ◽  
3D Printing Technology

Defects in the oral and maxillofacial (OMF) complex may lead to functional and esthetic impairment, aspiration, speech difficulty, and reduced quality of life. Reconstruction of such defects is considered one of the most challenging procedures in head and neck surgery. Transfer of different auto-grafts is still considered as the “gold standard” of regenerative and reconstructive procedures for OMF defects. However, harvesting of these grafts can lead to many complications including donor-site morbidity, extending of surgical time, incomplete healing of the donor site and others. Three-dimensional (3D) printing technology is an innovative technique that allows the fabrication of personalized implants and scaffolds that fit the precise anatomy of an individual’s defect and, therefore, has attracted significant attention during the last few decades, especially among head and neck surgeons. Here we discuss the most relevant applications of the 3D printing technology in the oral and maxillofacial surgery field. We further show different clinical examples of patients who were treated at our institute using the 3D technology and discuss the indications, different technologies, complications, and their clinical outcomes. We demonstrate that 3D technology may provide a powerful tool used for reconstruction of various OMF defects, enabling optimal clinical results in the suitable cases.

scholarly journals Cast Metal Surgical Guides: An Affordable Adjunct to Oral and Maxillofacial Surgery

2020 ◽  
Vol 5 ◽  
pp. 247275122096026
Author(s):  
Chitra Chakravarthy ◽  
Daisy Aranha ◽  
Santosh Kumar Malyala ◽  
Ravi S Patil
Keyword(s):  
3D Printing ◽  
Maxillofacial Surgery ◽  
Hybrid Approach ◽  
Cost Effective ◽  
Oral And Maxillofacial Surgery ◽  
Operating Table ◽  
Functional Rehabilitation ◽  
Printing Technology ◽  
3D Printing Technology ◽  
Surgical Guides

Additive manufacturing or 3-dimensional (3D) printing technology has an incredulous ability to create complex constructs with high exactitude. Surgical guides printed using this technology allows the transfer of the virtual surgical plan to the operating table, optimizing aesthetic outcomes, and functional rehabilitation. A vast variety of materials are currently being used in medical 3D printing, including metals, ceramics, polymers, and composites. The guides fabricated with titanium have high strength, excellent biocompatibility, and are sterilizable but take time to print and are expensive. We have thus followed a hybrid approach to fabricate an inexpensive surgical guide using metal where the advantage of 3D printing technology has been combined with the routinely followed investment casting procedure to fabricate guides using nickel–chromium, which has all the advantages of a metal and is cost-effective.

scholarly journals 3D Printing in Breast Reconstruction: From Bench to Bed

2021 ◽  
Vol 8 ◽  
Author(s):  
Xingdou Mu ◽  
Juliang Zhang ◽  
Yue Jiang
Keyword(s):  
Tissue Engineering ◽  
3D Printing ◽  
Breast Reconstruction ◽  
Reconstructive Surgical Procedures ◽  
Three Dimensional ◽  
Future Directions ◽  
Printing Technology ◽  
Reconstructive Procedures ◽  
3D Printing Technology ◽  
Reconstruction Methods

Surgical management of breast cancer often results in the absence of the breast. However, existing breast reconstruction methods may not meet the need for a replacement tissue. Tissue engineering with the use of emerging materials offers the promise of generating appropriate replacements. Three-dimensional (3D) printing technology has seen a significantly increased interest and application in medically-related fields in the recent years. This has been especially true in complex medical situations particularly when abnormal or complicated anatomical surgical considerations or precise reconstructive procedures are contemplated. In addition, 3D bio-printing which combines cells with bio-material scaffolds offers an exciting technology with significant applications in the field of tissue engineering. The purpose of this manuscript was to review a number of studies in which 3D printing technology has been used in breast reconstructive surgical procedures, and future directions and applications of 3D bio-printing.

scholarly journals Traditional versus mirror three-dimensional printing technology for isolated acetabular fractures: a retrospective study with a median follow-up of 25 months

2021 ◽  
Vol 49 (6) ◽  
pp. 030006052110285
Author(s):  
Kai Xiao ◽  
Bo Xu ◽  
Lin Ding ◽  
Weiguang Yu ◽  
Lei Bao ◽  
...  
Keyword(s):  
3D Printing ◽  
Three Dimensional ◽  
Operation Time ◽  
Harris Hip Score ◽  
Acetabular Fractures ◽  
Printing Technology ◽  
Three Dimensional Printing ◽  
3D Printing Technology ◽  
Significant Difference

Objective To assess the outcomes of traditional three-dimensional (3D) printing technology (TPT) versus mirror 3D printing technology (MTT) in treating isolated acetabular fractures (IAFs). Methods Consecutive patients with an IAF treated by either TPT or MTT at our tertiary medical centre from 2012 to 2018 were retrospectively reviewed. Follow-up was performed 1, 3, 6, and 12 months postoperatively and annually thereafter. The primary outcome was the Harris hip score (HHS), and the secondary outcomes were major intraoperative variables and key orthopaedic complications. Results One hundred fourteen eligible patients (114 hips) with an IAF (TPT, n = 56; MTT, n = 58) were evaluated. The median follow-up was 25 months (range, 21–28 months). At the last follow-up, the mean HHS was 82.46 ±14.70 for TPT and 86.30 ± 13.26 for MTT with a statistically significant difference. Significant differences were also detected in the major intraoperative variables (operation time, intraoperative blood loss, number of fluoroscopic screenings, and anatomical reduction number) and the major orthopaedic complications (loosening, implant failure, and heterotopic ossification). Conclusion Compared with TPT, MTT tends to produce accurate IAF reduction and may result in better intraoperative variables and a lower rate of major orthopaedic complications.

scholarly journals Porous PLAs with Controllable Density by FDM 3D Printing and Chemical Foaming Agent

Micromachines ◽  
2021 ◽  
Vol 12 (8) ◽  
pp. 866
Author(s):  
A. R. Damanpack ◽  
André Sousa ◽  
M. Bodaghi
Keyword(s):  
3D Printing ◽  
Flow Rate ◽  
Three Dimensional ◽  
Poly Lactic Acid ◽  
Layer By Layer ◽  
Printing Technology ◽  
Material Density ◽  
Foaming Agent ◽  
3D Printing Technology ◽  
Fabrication Parameters

This paper shows how fused decomposition modeling (FDM), as a three-dimensional (3D) printing technology, can engineer lightweight porous foams with controllable density. The tactic is based on the 3D printing of Poly Lactic Acid filaments with a chemical blowing agent, as well as experiments to explore how FDM parameters can control material density. Foam porosity is investigated in terms of fabrication parameters such as printing temperature and flow rate, which affect the size of bubbles produced during the layer-by-layer fabrication process. It is experimentally shown that printing temperature and flow rate have significant effects on the bubbles’ size, micro-scale material connections, stiffness and strength. An analytical equation is introduced to accurately simulate the experimental results on flow rate, density, and mechanical properties in terms of printing temperature. Due to the absence of a similar concept, mathematical model and results in the specialized literature, this paper is likely to advance the state-of-the-art lightweight foams with controllable porosity and density fabricated by FDM 3D printing technology.

scholarly journals Comparison of Presurgical Dental Models Manufactured with Two Different Three-Dimensional Printing Techniques

2020 ◽  
Vol 2020 ◽  
pp. 1-6 ◽  
Author(s):  
Marcin Metlerski ◽  
Katarzyna Grocholewicz ◽  
Aleksandra Jaroń ◽  
Mariusz Lipski ◽  
Grzegorz Trybek ◽  
...  
Keyword(s):  
3D Printing ◽  
Oral Surgery ◽  
Three Dimensional ◽  
Mean Deviation ◽  
Printing Technology ◽  
Three Dimensional Printing ◽  
Reference Models ◽  
3D Printing Technology ◽  
Dimensional Printing ◽  
Printing Time

Three-dimensional printing is a rapidly developing area of technology and manufacturing in the field of oral surgery. The aim of this study was comparison of presurgical models made by two different types of three-dimensional (3D) printing technology. Digital reference models were printed 10 times using fused deposition modelling (FDM) and digital light processing (DLP) techniques. All 3D printed models were scanned using a technical scanner. The trueness, linear measurements, and printing time were evaluated. The diagnostic models were compared with the reference models using linear and mean deviation for trueness measurements with computer software. Paired t-tests were performed to compare the two types of 3D printing technology. A P value < 0.05 was considered statistically significant. For FDM printing, all average distances between the reference points were smaller than the corresponding distances measured on the reference model. For the DLP models, the average distances in the three measurements were smaller than the original. Only one average distance measurement was greater. The mean deviation for trueness was 0.1775 mm for the FDM group and 0.0861 mm for the DLP group. Mean printing time for a single model was 517.6 minutes in FDM technology and 285.3 minutes in DLP. This study confirms that presurgical models manufactured with FDM and DLP technologies are usable in oral surgery. Our findings will facilitate clinical decision-making regarding the best 3D printing technology to use when planning a surgical procedure.

scholarly journals Three-Dimensional Printing: Custom-Made Implants for Craniomaxillofacial Reconstructive Surgery

2017 ◽  
Vol 10 (2) ◽  
pp. 089-098 ◽  
Author(s):  
Mariana Matias ◽  
Horácio Zenha ◽  
Horácio Costa
Keyword(s):  
3D Printing ◽  
Reconstructive Surgery ◽  
Three Dimensional ◽  
Tactile Feedback ◽  
Current Status ◽  
Printing Technology ◽  
Three Dimensional Printing ◽  
3D Printing Technology ◽  
Custom Made ◽  
The Aesthetic

Craniomaxillofacial reconstructive surgery is a challenging field. First it aims to restore primary functions and second to preserve craniofacial anatomical features like symmetry and harmony. Three-dimensional (3D) printed biomodels have been widely adopted in medical fields by providing tactile feedback and a superior appreciation of visuospatial relationship between anatomical structures. Craniomaxillofacial reconstructive surgery was one of the first areas to implement 3D printing technology in their practice. Biomodeling has been used in craniofacial reconstruction of traumatic injuries, congenital disorders, tumor removal, iatrogenic injuries (e.g., decompressive craniectomies), orthognathic surgery, and implantology. 3D printing has proven to improve and enable an optimization of preoperative planning, develop intraoperative guidance tools, reduce operative time, and significantly improve the biofunctional and the aesthetic outcome. This technology has also shown great potential in enriching the teaching of medical students and surgical residents. The aim of this review is to present the current status of 3D printing technology and its practical and innovative applications, specifically in craniomaxillofacial reconstructive surgery, illustrated with two clinical cases where the 3D printing technology was successfully used.

3D PRINTING TECHNOLOGY IN HUMAN ANATOMY MODERN TEACHING AND LEARNING

2019 ◽  
Vol 1 ◽  
pp. 234
Author(s):  
Dzintra Kazoka ◽  
Mara Pilmane
Keyword(s):  
3D Printing ◽  
Teaching And Learning ◽  
Three Dimensional ◽  
Human Anatomy ◽  
Anatomical Models ◽  
Printing Technology ◽  
3D Printing Technology ◽  
Medical Study ◽  
Study Process ◽  
Teaching Learning

There are various combinations of 3D printing technology and medical study process. The aim of this study was to summarize our first experience on 3D printing and outline how 3D printed models can be successfully used in Human Anatomy modern teaching and learning. In 2018 autumn semester, together with traditional methods, a three-dimensional (3D) printing has been introduced into Human Anatomy curriculum at Department of Morphology. In practical classes 39 groups of students from Faculty of Medicine 1st year together with 3 tutors used 3 different open source softwares to create anatomical models and prepared them for printing process. All anatomical models were produced using an FDM 3D printer, a Prusa i3 MK2 (Prusa Research). As methods for data collection were used our observational notes during teaching and learning, analysis of discussions between tutors and students, comments on the preparing and usability of the created and printed models. 3D printing technology offered students a powerful tool for their teaching, learning and creativity, provided possibility to show human body structures or variations. Presented data offered valuable information about current situation and these results were suitable for the further development of the Human Anatomy study course.

scholarly journals 3D-Printed Biopolymers for Tissue Engineering Application

2014 ◽  
Vol 2014 ◽  
pp. 1-13 ◽  
Author(s):  
Xiaoming Li ◽  
Rongrong Cui ◽  
Lianwen Sun ◽  
Katerina E. Aifantis ◽  
Yubo Fan ◽  
...  
Keyword(s):  
Tissue Engineering ◽  
3D Printing ◽  
Three Dimensional ◽  
Engineering Application ◽  
Tissue Engineering Application ◽  
Printing Technology ◽  
3D Printing Technology ◽  
Potential Applications ◽  
3D Printed ◽  
Dimensional Object

3D printing technology has recently gained substantial interest for potential applications in tissue engineering due to the ability of making a three-dimensional object of virtually any shape from a digital model. 3D-printed biopolymers, which combine the 3D printing technology and biopolymers, have shown great potential in tissue engineering applications and are receiving significant attention, which has resulted in the development of numerous research programs regarding the material systems which are available for 3D printing. This review focuses on recent advances in the development of biopolymer materials, including natural biopolymer-based materials and synthetic biopolymer-based materials prepared using 3D printing technology, and some future challenges and applications of this technology are discussed.

Methodology of technological evolution for three-dimensional printing

2016 ◽  
Vol 116 (1) ◽  
pp. 122-146 ◽  
Author(s):  
Sangsung Park ◽  
Juhwan Kim ◽  
Hongchul Lee ◽  
Dongsik Jang ◽  
Sunghae Jun
Keyword(s):  
3D Printing ◽  
Quantitative Methods ◽  
Three Dimensional ◽  
Principal Component ◽  
Technological Evolution ◽  
Time Series Regression ◽  
Printing Technology ◽  
Content Type ◽  
3D Printing Technology ◽  
The Future

Purpose – An increasing amount of attention is being paid to three-dimensional (3D) printing technology. The technology itself is based on diverse technologies such as laser beams and materials. Hence, 3D printing technology is a converging technology that produces 3D objects using a 3D printer. To become technologically competitive, many companies and nations are developing technologies for 3D printing. So to know its technological evolution is meaningful for developing 3D printing in the future. The paper aims to discuss these issues. Design/methodology/approach – To get technological competitiveness of 3D printing, the authors should know the most important and essential technology for 3D printing. An understanding of the technological evolution of 3D printing is needed to forecast its future technologies and build the R & D planning needed for 3D printing. In this paper, the authors propose a methodology to analyze the technological evolution of 3D printing. The authors analyze entire patent documents related to 3D printing to construct a technological evolution model. The authors use the statistical methods such as time series regression, association analysis based on graph theory, and principal component analysis for patent analysis of 3D printing technology. Findings – Using the proposed methodology, the authors show the technological analysis results of 3D printing and predict its future aspects. Though many and diverse technologies are developed and involved in 3D printing, the authors know only a few technologies take lead the technological evolution of 3D printing. In this paper, the authors find this evolution of technology management for 3D printing. Practical implications – If not all, most people would agree that 3D printing technology is one of the leading technologies to improve the quality of life. So, many companies have developed a number of technologies if they were related to 3D printing. But, most of them have not been considered practical. These were not effective research and development for 3D printing technology. In the study, the authors serve a methodology to select the specific technologies for practical used of 3D printing. Originality/value – Diverse predictions for 3D printing technology have been introduced in many academic and industrial fields. Most of them were made by subjective approaches depended on the knowledge and experience of the experts concerning 3D printing technology. So, they could be fluctuated according to the congregated expert groups, and be unstable for efficient R & D planning. To solve this problem, the authors study on more objective approach to predict the future state of 3D printing by analyzing the patent data of the developed results so far achieved. The contribution of this research is to take a new departure for understanding 3D printing technology using objective and quantitative methods.

Sign in / Sign up

Export Citation Format

Share Document