scholarly journals Superparamagnetic Fe3O4@CA Nanoparticles and Their Potential as Draw Solution Agents in Forward Osmosis

Nanomaterials ◽  
2021 ◽  
Vol 11 (11) ◽  
pp. 2965
Author(s):  
Irena Petrinic ◽  
Janja Stergar ◽  
Hermina Bukšek ◽  
Miha Drofenik ◽  
Sašo Gyergyek ◽  
...  
Keyword(s):  
Osmotic Pressure ◽  
Magnetic Measurements ◽  
Water Flux ◽  
Forward Osmosis ◽  
Cross Flow ◽  
Solute Flux ◽  
Colloidal Solutions ◽  
Initial Water ◽  
Cross Flow Filtration ◽  
Draw Solution

In this study, citric acid (CA)-coated magnetite Fe3O4 magnetic nanoparticles (Fe3O4@CA MNPs) for use as draw solution (DS) agents in forward osmosis (FO) were synthesized by co-precipitation and characterized by Fourier transform infrared spectroscopy (FTIR), thermogravimetric analysis (TGA), dynamic light scattering (DLS), transmission electron microscopy (TEM) and magnetic measurements. Prepared 3.7% w/w colloidal solutions of Fe3O4@CA MNPs exhibited an osmotic pressure of 18.7 bar after purification without aggregation and a sufficient magnetization of 44 emu/g to allow DS regeneration by an external magnetic field. Fe3O4@CA suspensions were used as DS in FO cross-flow filtration with deionized (DI) water as FS and with the active layer of the FO membrane facing the FS and NaCl as a reference DS. The same transmembrane bulk osmotic pressure resulted in different water fluxes for NaCl and MNPs, respectively. Thus the initial water flux with Fe3O4@CA was 9.2 LMH whereas for 0.45 M NaCl as DS it was 14.1 LMH. The reverse solute flux was 0.08 GMH for Fe3O4@CA and 2.5 GMH for NaCl. These differences are ascribed to a more pronounced internal dilutive concentration polarization with Fe3O4@CA as DS compared to NaCl as DS. This research demonstrated that the proposed Fe3O4@CA can be used as a potential low reverse solute flux DS for FO processes.

scholarly journals Preparation of defect free TFC FO membranes using robust and highly porous ceramic substrate

2018 ◽  
Vol 1 (4) ◽  
Author(s):  
Jincai Su ◽  
Yanyan Wei ◽  
Hui Li
Keyword(s):  
Osmotic Pressure ◽  
Interfacial Polymerization ◽  
Pure Water ◽  
Porous Ceramic ◽  
Water Flux ◽  
Solute Flux ◽  
Structural Parameter ◽  
Solute Permeability ◽  
Draw Solution ◽  
Surface Pores

In this study, robust and defect-free thin film composite (TFC) forward osmosis (FO) membranes have been successfully fabricated using ceramic hollow fibers as the substrate. Polydopamine (PDA) coating under controlled conditions is effective to reduce the surface pores of the substrate and make the substrate smooth enough for the interfacial polymerization. The pure water permeability (A), solute permeability (B) and structural parameter (S) of the resultant FO membrane are 0.854 L·m-2h-1bar-1 (LMH/Bar) 0.186 L·m-2h-1 (LMH) and 1720 µm, respectively. The water flux and reverse draw solute flux are measured using NaCl and proprietary ferric sodium citrate (FeNaCA) draw solutions at low and high osmotic pressure ranges. With increasing the osmotic pressure, higher water flux is obtained but its increase is not directly proportional to the increase in the osmotic pressure. At the membrane surface, the effect of dilutive concentration polarization is much less serious for FeNaCA draw solutions. At an osmotic pressure of 89.6 bar, the developed TFC membrane generates water fluxes of 11.5 and 30.0 LMH using NaCl and synthesized FeNaCA draw solutions. The corresponding reverse draw solute flux is 7.0 g·m-2h-1 (gMH) for NaCl draw solution but it is not detectable for FeNaCA draw solution. This means that the developed TFC FO membranes are defect free and their surface pores are at molecular level. The performance of the developed TFC FO membranes are also demonstrated for the enrichment of BSA protein.

scholarly journals Polymer Having Dicationic Structure in Dumbbell Shape for Forward Osmosis Process

Polymers ◽  
2019 ◽  
Vol 11 (3) ◽  
pp. 571 ◽  
Author(s):  
Taehyung Kim ◽  
Changha Ju ◽  
Chanhyuk Park ◽  
Hyo Kang
Keyword(s):  
Aqueous Solutions ◽  
Pure Water ◽  
Water Flux ◽  
Forward Osmosis ◽  
Feed Solution ◽  
Solution Temperature ◽  
Solute Flux ◽  
Responsive Polymers ◽  
Draw Solution ◽  
Efficient Recovery

The thermal-responsive polymers, poly(alkane-1,#-diylbis(tri-n-butylphosphonium) 4-vinylbenzenesulfonate) (PSSBP#, # = 8, 6, and 4), where # is the number of carbon atoms in the central bridge structure of the dicationic phosphonium moiety, were synthesized to examine their potential application as draw solutes in forward osmosis (FO). The polymers exhibited low critical solution temperature (LCST) characteristics in aqueous solutions, which is essential for recovering a draw solute from pure water. The LCSTs of the 20 wt% aqueous solutions of PSSBP8, PSSBP6, and PSSBP4 were confirmed to be approximately 30, 38, and 26 °C, respectively, which is advantageous in terms of energy requirements for the recovering draw solute. When the concentration of the PSSBP4 draw solution was 20 wt%, water flux and reverse solute flux were approximately 1.61 LMH and 0.91 gMH, respectively, in the active layer facing the draw solution (AL-DS) system when the feed solution was distilled water. The PSSBP# thermal-responsive draw solute has considerable potential for use as a next-generation draw solute because of its excellent osmotic performance and efficient recovery. Therefore, this study provides inspiration for novel ideas regarding structural transformations of polymers and their applicability as draw solutes.

scholarly journals Investigating the performance of hydroponic nutrient solutions as potential draw solutions for fertilizer drawn forward osmosis

2021 ◽  
Author(s):  
Mohamed Bassiouny ◽  
Peter Nasr ◽  
Hani Sewilam
Keyword(s):  
High Performance ◽  
Low Cost ◽  
Water Flux ◽  
Forward Osmosis ◽  
Feed Solution ◽  
Solute Flux ◽  
Water Recovery ◽  
Salt Rejection ◽  
Draw Solution ◽  
Nutrient Solutions

Abstract This research project aims at investigating the performance of hydroponic nutrient solutions as draw solutions for desalination using the fertilizer drawn forward osmosis (FDFO) process. Six different lettuce and leafy greens hydroponic nutrient stock solutions were prepared according to the literature and used in this study and tested on a bench-scale forward osmosis unit as draw solutions for the process. The feed solution for the process was De-Ionized water mixed with NaCl in different concentrations, to represent different salinities of brackish groundwater. The draw efficiency of each solution was measured based on water flux, specific reverse solute flux, water recovery, and salt rejection. It was concluded that of the six tested nutrient solutions, the “Resh Florida, California” solution is the recommended solution to be used as draw solution for fertilizer drawn forward osmosis, due to its high performance in terms of water recovery (15.75%), flux (11 l/m2/h), salt rejection (92%) and SRSF (highest recorded SRSF for a specific ion (SO4 2−) was 7.3 g/l), as well as its low cost, relative to the other highly performing draw solution “Chekli” ($1.07/l vs. $3.73/l).

scholarly journals Forward Osmosis: Temperature Effects By Using Pome as Feed Solution

2015 ◽  
Vol 15 (1) ◽  
pp. 31 ◽  
Author(s):  
Hanizah Arifin ◽  
Thomas S.Y. Choong ◽  
Chan Kam Rong ◽  
Fakhru'l Al-Razi Ahmadun ◽  
Luqman Chuah Abdullah
Keyword(s):  
Water Flux ◽  
Forward Osmosis ◽  
Cross Flow ◽  
Feed Solution ◽  
Water Fluxes ◽  
Energy Applications ◽  
Draw Solution ◽  
Influence Of Temperature On ◽  
Cross Flow Velocity ◽  
Higher Temperature

Forward osmosis (FO) has recently been considered as one of the promising technologies for low energy applications. Factors that influence FO performance are draw solution, types of membrane, membrane orientation, cross flow velocity, module configuration and temperature effect. In this study, the influence of temperature on the performance of FO process has been studied in terms of water flux by using raw POME as feed solution. A higher temperature creates a higher water fluxes at various draw solution concentrations. Percentages of water flux increments for raw POME are between 7% to 9% from 25ºC to 35ºC and 32% to 75% from 25ºC to 45ºC.

Preliminary study of osmotic membrane bioreactor: effects of draw solution on water flux and air scouring on fouling

2010 ◽  
Vol 62 (6) ◽  
pp. 1353-1360 ◽  
Author(s):  
Jian-Jun Qin ◽  
Kiran A. Kekre ◽  
Maung H. Oo ◽  
Guihe Tao ◽  
Chee L. Lay ◽  
...  
Keyword(s):  
Osmotic Pressure ◽  
Membrane Bioreactor ◽  
Water Flux ◽  
Forward Osmosis ◽  
Operating Conditions ◽  
Draw Solution ◽  
Membrane Flux ◽  
Osmotic Membrane Bioreactor ◽  
Flux Decline ◽  
Preliminary Study

Preliminary study on a novel osmotic membrane bioreactor (OMBR) was explored. Objective of this study was to investigate the effects of draw solution on membrane flux and air scouring at the feed side on fouling tendency in a pilot OMBR system composing the anoxic/aerobic and forward osmosis (FO) processes. Domestic sewage was the raw feed, FO membrane from HTI and NaCl/MgSO4 draw solutions were used in the experiments. Fluxes of 3 l/m2/h (LMH) and 7.2 LMH were achieved at osmotic pressure of 5 and 22.4 atm, respectively. No significant flux decline was observed at 3 LMH over 190 h and at 7.2 LMH over 150 h when air scouring was provided at the feed side of the membrane. However, without air scouring, the flux at 22.4 atm osmotic pressure declined by 30% after 195 h and then levelled off. The potential advantages of the fouling reversibility with air scouring under the operating conditions of the pilot OMBR and better water quality in OMBR over the conventional MBR were preliminarily demonstrated.

scholarly journals Evaluation of polyvinylpyrrolidone as draw solute for desalination forward osmosis systems

2021 ◽  
Author(s):  
Quang Trung Nguyen ◽  
Minh Tao Hoang ◽  
Tuan Hung Trinh ◽  
Ngoc Tung Nguyen ◽  
Truong Giang Le
Keyword(s):  
Molecular Weight ◽  
Water Flux ◽  
Forward Osmosis ◽  
Feed Solution ◽  
Raw Material ◽  
Solute Flux ◽  
Initial Concentration ◽  
Draw Solution ◽  
Material Cost ◽  
Solution Parameters

Abstract In this study, polyvinylpyrrolidone (PVP) was evaluated as a potential draw solute for desalination forward osmosis (FO) systems. The effect of various draw solute and draw solution parameters on the efficiency of FO operation was investigated, including PVP molecular weight, PVP concentration in solution, and the salinity of feed solution. Experiment results showed that at draw solution initial concentration of 200 g/L and feed solution initial salinity up to 15 g/L, the PVP-based draw solution can offer water flux up to 14.23 LMH in FO mode with raw material cost only at 0.61 USD/m3. PVP K17 was proven to be an effective draw solute for FO systems, providing good water flux and low reverse draw solute flux; while also being relatively non-toxic, non-corrosive, cheap and widely available compared to other types of novel draw solutes.

scholarly journals Water Recovery from Bioreactor Mixed Liquors Using Forward Osmosis with Polyelectrolyte Draw Solutions

Membranes ◽  
2021 ◽  
Vol 12 (1) ◽  
pp. 61
Author(s):  
Calen R. Raulerson ◽  
Sudeep C. Popat ◽  
Scott M. Husson
Keyword(s):  
Water Purification ◽  
Water Flux ◽  
Forward Osmosis ◽  
Space Missions ◽  
Solute Flux ◽  
Water Recovery ◽  
Direct Flow ◽  
Draw Solution ◽  
Long Duration ◽  
Cake Layer

This paper reports on the use of forward osmosis (FO) with polyelectrolyte draw solutions to recover water from bioreactor mixed liquors. The work was motivated by the need for new regenerative water purification technologies to enable long-duration space missions. Osmotic membrane bioreactors may be an option for water and nutrient recovery in space if they can attain high water flux and reverse solute flux selectivity (RSFS), which quantifies the mass of permeated water per mass of draw solute that has diffused from the draw solution into a bioreactor. Water flux was measured in a direct flow system using wastewater from a municipal wastewater treatment plant and draw solutions prepared with two polyelectrolytes at different concentrations. The direct flow tests displayed a high initial flux (>10 L/m2/h) that decreased rapidly as solids accumulated on the feed side of the membrane. A test with deionized water as the feed revealed a small mass of polyelectrolyte crossover from the draw solution to the feed, yielding an RSFS of 80. Crossflow filtration experiments demonstrated that steady state flux above 2 L/m2·h could be maintained for 70 h following an initial flux decline due to the formation of a foulant cake layer. This study established that FO could be feasible for regenerative water purification from bioreactors. By utilizing a polyelectrolyte draw solute with high RSFS, we expect to overcome the need for draw solute replenishment. This would be a major step towards sustainable operation in long-duration space missions.

scholarly journals Structural investigation and application of Tween 80-choline chloride self-assemblies as osmotic agent for water desalination

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Yasamin Bide ◽  
Marzieh Arab Fashapoyeh ◽  
Soheila Shokrollahzadeh
Keyword(s):  
Nonionic Surfactant ◽  
Choline Chloride ◽  
Water Flux ◽  
Forward Osmosis ◽  
Tween 80 ◽  
Average Diameter ◽  
Feed Solution ◽  
Water Desalination ◽  
Draw Solution ◽  
Osmotic Agent

AbstractForward osmosis (FO) process has been extensively considered as a potential technology that could minimize the problems of traditional water desalination processes. Finding an appropriate osmotic agent is an important concern in the FO process. For the first time, a nonionic surfactant-based draw solution was introduced using self-assemblies of Tween 80 and choline chloride. The addition of choline chloride to Tween 80 led to micelles formation with an average diameter of 11.03 nm. The 1H NMR spectra exhibited that all groups of Tween 80 were interacted with choline chloride by hydrogen bond and Van der Waals’ force. The influence of adding choline chloride to Tween 80 and the micellization on its osmotic activity was investigated. Despite the less activity of single components, the average water flux of 14.29 L m‒2 h‒1 was obtained using 0.15 M of Tween 80-choline chloride self-assembly as draw solution in the FO process with DI water feed solution. Moreover, various concentrations of NaCl aqueous solutions were examined as feed solution. This report proposed a possible preparation of nonionic surfactant-based draw solutions using choline chloride additive with enhanced osmotic activities that can establish an innovative field of study in water desalination by the FO process.

scholarly journals Using Reverse Osmosis Membrane at High Temperature for Water Recovery and Regeneration from Thermo-Responsive Ionic Liquid-Based Draw Solution for Efficient Forward Osmosis

Membranes ◽  
2021 ◽  
Vol 11 (8) ◽  
pp. 588
Author(s):  
Eiji Kamio ◽  
Hiroki Kurisu ◽  
Tomoki Takahashi ◽  
Atsushi Matsuoka ◽  
Tomohisa Yoshioka ◽  
...  
Keyword(s):  
Ionic Liquid ◽  
High Temperature ◽  
Energy Saving ◽  
Osmotic Pressure ◽  
Reverse Osmosis ◽  
Forward Osmosis ◽  
Solution Temperature ◽  
Water Recovery ◽  
Temperature Dependent ◽  
Draw Solution

Forward osmosis (FO) membrane process is expected to realize energy-saving seawater desalination. To this end, energy-saving water recovery from a draw solution (DS) and effective DS regeneration are essential. Recently, thermo-responsive DSs have been developed to realize energy-saving water recovery and DS regeneration. We previously reported that high-temperature reverse osmosis (RO) treatment was effective in recovering water from a thermo-responsive ionic liquid (IL)-based DS. In this study, to confirm the advantages of the high-temperature RO operation, thermo-sensitive IL-based DS was treated by an RO membrane at temperatures higher than the lower critical solution temperature (LCST) of the DS. Tetrabutylammonium 2,4,6-trimethylbenznenesulfonate ([N4444][TMBS]) with an LCST of 58 °C was used as the DS. The high-temperature RO treatment was conducted at 60 °C above the LCST using the [N4444][TMBS]-based DS-lean phase after phase separation. Because the [N4444][TMBS]-based DS has a significantly temperature-dependent osmotic pressure, the DS-lean phase can be concentrated to an osmotic pressure higher than that of seawater at room temperature (20 °C). In addition, water can be effectively recovered from the DS-lean phase until the DS concentration increased to 40 wt%, and the final DS concentration reached 70 wt%. From the results, the advantages of RO treatment of the thermo-responsive DS at temperatures higher than the LCST were confirmed.

Enhancing Water Permeability with Super-hydrophilic Metal-Organic Frameworks and Hydrophobic Straight Pores

2021 ◽  
Author(s):  
Mehdi Habibollahzadeh ◽  
Juran Noh ◽  
Liang Feng ◽  
Hong-Cai Zhou ◽  
Ahmed Abdel-Wahab ◽  
...  
Keyword(s):  
Osmotic Pressure ◽  
Water Permeability ◽  
Metal Organic Frameworks ◽  
Water Flux ◽  
Forward Osmosis ◽  
High Water ◽  
Metal Organic

High water flux and salt selectivity have been the most demanding goals for osmosis-based membranes. Osmotic pressure differences across membranes are particularly important in emerging forward osmosis and pressure retarded...

Sign in / Sign up

Export Citation Format

Share Document