scholarly journals Efficient Improvement in Fracture Toughness of Laminated Composite by Interleaving Functionalized Nanofibers

Polymers ◽  
2021 ◽  
Vol 13 (15) ◽  
pp. 2509
Author(s):  
Seyed Mohammad Javad Razavi ◽  
Rasoul Esmaeely Neisiany ◽  
Moe Razavi ◽  
Afsaneh Fakhar ◽  
Vigneshwaran Shanmugam ◽  
...  
Keyword(s):  
Fracture Toughness ◽  
Fracture Behavior ◽  
Laminated Composite ◽  
Carbon Phase ◽  
Reinforced Composite ◽  
Reinforcing Agent ◽  
The Matrix ◽  
As Stress ◽  
Double Cantilever Beam Test ◽  
Pan Nanofiber

Functionalized polyacrylonitrile (PAN) nanofibers were used in the present investigation to enhance the fracture behavior of carbon epoxy composite in order to prevent delamination if any crack propagates in the resin rich area. The main intent of this investigation was to analyze the efficiency of PAN nanofiber as a reinforcing agent for the carbon fiber-based epoxy structural composite. The composites were fabricated with stacked unidirectional carbon fibers and the PAN powder was functionalized with glycidyl methacrylate (GMA) and then used as reinforcement. The fabricated composites’ fracture behavior was analyzed through a double cantilever beam test and the energy release rate of the composites was investigated. The neat PAN and functionalized PAN-reinforced samples had an 18% and a 50% increase in fracture energy, respectively, compared to the control composite. In addition, the samples reinforced with functionalized PAN nanofibers had 27% higher interlaminar strength compared to neat PAN-reinforced composite, implying more efficient stress transformation as well as stress distribution from the matrix phase (resin-rich area) to the reinforcement phase (carbon/phase) of the composites. The enhancement of fracture toughness provides an opportunity to alleviate the prevalent issues in laminated composites for structural operations and facilitate their adoption in industries for critical applications.

Microstructure, Mechanical Properties, Sintering and Fracture Behavior of Ti(C, N) Based Cermets Granules/Ti(C, N) Based Cermets Composite

2020 ◽  
Vol 837 ◽  
pp. 139-145
Author(s):  
Ai Jun Liu ◽  
Gang Li ◽  
Ning Liu ◽  
Ke Bei Chen ◽  
Hai Dong Yang
Keyword(s):  
Mechanical Properties ◽  
Fracture Toughness ◽  
Relative Density ◽  
Fracture Behavior ◽  
Rupture Strength ◽  
Binder Phase ◽  
Hard Phase ◽  
Opposite Trend ◽  
The Matrix ◽  
Sintering Properties

Effect of Ti (C,N) based cermets granule on the microstructure, mechanical properties, sintering and fracture behavior of Ti (C,N) based cermets was investigated. Results show that the Ti (C,N) based cermets granules distribute in the matrix homogeneously. A nanoindentation study was performed on hard phase and binder phase in the matrix and granule. With the increase of granules content, sintering properties is worse. With the increase of granules content, transverse rupture strength (TRS) and relative density decrease gradually, while the hardness has an opposite trend. The fracture toughness increases firstly with increasing granule, and then decreases with the further increase of granules. Higher fracture toughness of the cermets is mainly owing to the crack branch and higher fracture energy of coarse granule.

Ductile Phase Toughening of MoSi2-Chemical Compatibility and Fracture Toughness

1990 ◽  
Vol 194 ◽  
Author(s):  
L. Xiao ◽  
Y. S. Kim ◽  
Reza Abbaschian
Keyword(s):  
Fracture Toughness ◽  
Reinforced Composites ◽  
Matrix Interface ◽  
Chemical Compatibility ◽  
Interaction Zone ◽  
Ductile Phase ◽  
Reinforced Composite ◽  
The Matrix ◽  
Mullite Coatings ◽  
Bonding Characteristics

AbstractChemical compatibility between oxide coated Nb filament reinforcements and MoSi2 was investigated. It was determined that ZrO2, Al2O3, and mullite coatings were chemically compatible with both Nb and MoSi2. Comparison between coated and uncoated filaments indicated that the coatings reduced the thickness of the interaction zone. The fracture toughness of the Nb filament reinforced composites showed an increase, while W filament reinforced composite showed a decrease, in the toughness compared to that of the matrix. The results are discussed in terms of the mismatches in the coefficients of thermal expansion and the bonding characteristics of the reinforcement/matrix interface.

scholarly journals An Assessment of ASTM E1922 for Measuring the Translaminar Fracture Toughness of Laminated Polymer Matrix Composite Materials

Polymers ◽  
2021 ◽  
Vol 13 (18) ◽  
pp. 3129
Author(s):  
Islam El-Sagheer ◽  
Amr A. Abd-Elhady ◽  
Hossam El-Din M. Sallam ◽  
Soheir A. R. Naga
Keyword(s):  
Fracture Toughness ◽  
Glass Fibers ◽  
Crack Tip ◽  
Laminated Composite ◽  
Fiber Reinforced Polymer ◽  
Fiber Direction ◽  
Reinforced Polymer ◽  
The Matrix ◽  
American Society ◽  
Cracked Specimens

The main objective of this work is to predict the exact value of the fracture toughness (KQ) of fiber-reinforced polymer (FRP). The drawback of the American Society for Testing Materials (ASTM) E1922 specimen is the lack of intact fibers behind the crack-tip as in the real case, i.e., through-thickness cracked (TTC) specimen. The novelty of this research is to overcome this deficiency by suggesting unprecedented cracked specimens, i.e., matrix cracked (MC) specimens. This MC exists in the matrix (epoxy) without cutting the glass fibers behind the crack-tip in the unidirectional laminated composite. Two different cracked specimen geometries according to ASTM E1922 and ASTM D3039 were tested. 3-D FEA was adopted to predict the damage failure and geometry correction factor of cracked specimens. The results of the TTC ASTM E1922 specimen showed that the crack initiated perpendicular to the fiber direction up to 1 mm. Failure then occurred due to crack propagation parallel to the fiber direction, i.e., notch insensitivity. As expected, the KQ of the MC ASTM D3039 specimen is higher than that of the TTC ASTM D3039 specimen. The KQ of the MC specimen with two layers is about 1.3 times that of the MC specimen with one layer.

scholarly journals Interlaminar fracture toughness properties of hybrid glass fiber-reinforced composite interlayered with carbon nanotube using electrospray deposition

2021 ◽  
Vol 10 (1) ◽  
pp. 1766-1775
Author(s):  
Fatin Nur Amirah Mohd Sabri ◽  
Muhammad Razlan Zakaria ◽  
Hazizan Md Akil ◽  
Mohd Shukur Zainol Abidin ◽  
Aslina Anjang Ab Rahman ◽  
...  
Keyword(s):  
Fracture Toughness ◽  
Glass Fiber ◽  
Control Sample ◽  
Laminated Composite ◽  
Test Method ◽  
Interlaminar Fracture Toughness ◽  
Electrospray Deposition ◽  
Interlaminar Fracture ◽  
Glass Fiber Reinforced ◽  
Double Cantilever Beam Test

Abstract The electrospray deposition (ESD) method was used to deposit carbon nanotubes (CNTs) onto the surface of glass fiber (GF). The morphology of the hybrid CNTs-GF was analyzed using a field emission scanning electron microscope, and the images indicated that the CNTs were uniformly and homogenously deposited onto the GF’s surface. Laminated composite based on GF and hybrid CNTs-GF were then fabricated via vacuum-assisted resin transfer molding. The mode I interlaminar fracture toughness was measured using the double cantilever beam test method. The hybrid CNTs-GF showed a 34% increase in fracture toughness relative to the control sample. The mechanism of interlaminar fracture toughness enhancement was elucidated via fractography, where fiber bridging, adhesive and cohesive failures, hackles, and coarse matrix surface were observed along the crack pathways.

DURALCAN F3S.xxS

Alloy Digest ◽  
1994 ◽  
Vol 43 (10) ◽  
Keyword(s):  
Fracture Toughness ◽  
Silicon Carbide ◽  
Compressive Strength ◽  
Aluminum Alloy ◽  
High Temperature ◽  
Base Alloy ◽  
Alloy Matrix ◽  
Reinforced Composite ◽  
Temperature Performance ◽  
Aluminum Alloy Matrix

Abstract Duralcan F3S.xxS is a heat treatable aluminum alloy-matrix gravity composite. The base alloy is similar to Aluminum 359 (Alloy Digest Al-188, July 1969); the discontinuously reinforced composite is silicon carbide. This datasheet provides information on composition, physical properties, hardness, elasticity, tensile properties, and compressive strength as well as fracture toughness and fatigue. It also includes information on high temperature performance. Filing Code: AL-329. Producer or source: Alcan Aluminum Corporation.

scholarly journals Self-Reinforced Nylon 6 Composite for Smart Vibration Damping

Polymers ◽  
2021 ◽  
Vol 13 (8) ◽  
pp. 1235
Author(s):  
Bidita Salahuddin ◽  
Rahim Mutlu ◽  
Tajwar A. Baigh ◽  
Mohammed N. Alghamdi ◽  
Shazed Aziz
Keyword(s):  
Matrix Material ◽  
Nylon 6 ◽  
Vibration Damping ◽  
Vibration Energy ◽  
Damping Factor ◽  
Passive Vibration Control ◽  
Reinforced Composite ◽  
Coiled Structure ◽  
The Matrix ◽  
3D Printed

Passive vibration control using polymer composites has been extensively investigated by the engineering community. In this paper, a new kind of vibration dampening polymer composite was developed where oriented nylon 6 fibres were used as the reinforcement, and 3D printed unoriented nylon 6 was used as the matrix material. The shape of the reinforcing fibres was modified to a coiled structure which transformed the fibres into a smart thermoresponsive actuator. This novel self-reinforced composite was of high mechanical robustness and its efficacy was demonstrated as an active dampening system for oscillatory vibration of a heated vibrating system. The blocking force generated within the reinforcing coiled actuator was responsible for dissipating vibration energy and increase the magnitude of the damping factor compared to samples made of non-reinforced nylon 6. Further study shows that the appropriate annealing of coiled actuators provides an enhanced dampening capability to the composite structure. The extent of crystallinity of the reinforcing actuators is found to directly influence the vibration dampening capacity.

Fracture Toughness Testing and its Implications to Engineering Fracture Mechanics Analysis of Energy Pipelines

2018 ◽  
Author(s):  
Sergio Limon ◽  
Peter Martin ◽  
Mike Barnum ◽  
Robert Pilarczyk
Keyword(s):  
Fracture Toughness ◽  
Fracture Mechanics ◽  
Test Data ◽  
Fracture Mode ◽  
Fracture Process ◽  
Fracture Behavior ◽  
Fracture Initiation ◽  
Fracture Toughness Testing ◽  
Final Fracture ◽  
Toughness Testing

The fracture process of energy pipelines can be described in terms of fracture initiation, stable fracture propagation and final fracture or fracture arrest. Each of these stages, and the final fracture mode (leak or rupture), are directly impacted by the tendency towards brittle or ductile behavior that line pipe steels have the capacity to exhibit. Vintage and modern low carbon steels, such as those used to manufacture energy pipelines, exhibit a temperature-dependent transition from ductile-to-brittle behavior that affects the fracture behavior. There are numerous definitions of fracture toughness in common usage, depending on the stage of the fracture process and the behavior or fracture mode being evaluated. The most commonly used definitions in engineering fracture analysis of pipelines with cracks or long-seam weld defects are related to fracture initiation, stable propagation or final fracture. When choosing fracture toughness test data for use in engineering Fracture Mechanics-based assessments of energy pipelines, it is important to identify the stage of the fracture process and the expected fracture behavior in order to appropriately select test data that represent equivalent conditions. A mismatch between the physical fracture event being modeled and the chosen experimental fracture toughness data can result in unreliable predictions or overly conservative results. This paper presents a description of the physical fracture process, behavior and failure modes that pipelines commonly exhibit as they relate to fracture toughness testing, and their implications when evaluating cracks and cracks-like features in pipelines. Because pipeline operators, and practitioners of engineering Fracture Mechanics analyses, are often faced with the challenge of only having Charpy fracture toughness available, this paper also presents a review of the various correlations of Charpy toughness data to fracture toughness data expressed in terms of KIC or JIC. Considerations with the selection of an appropriate correlation for determining the failure pressure of pipelines in the presence of cracks and long-seam weld anomalies will be discussed.

scholarly journals Mechanochemical Synthesis and Rapid Consolidation of Nanocrystalline 3NiAl-Al2O3Composites

2011 ◽  
Vol 2011 ◽  
pp. 1-5 ◽  
Author(s):  
In-Jin Shon ◽  
In-Yong Ko ◽  
Seung-Hoon Jo ◽  
Jung-Mann Doh ◽  
Jin-Kook Yoon ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Fracture Toughness ◽  
Mechanochemical Synthesis ◽  
High Frequency ◽  
Nanocrystalline Materials ◽  
Physical And Mechanical Properties ◽  
High Energy ◽  
Reinforced Composite ◽  
Energy Ball ◽  
High Frequency Induction

Nanopowders of 3NiAl and Al2O3were synthesized from 3NiO and 5Al powders by high-energy ball milling. Nanocrystalline Al2O3reinforced composite was consolidated by high-frequency induction-heated sintering within 3 minutes from mechanochemically synthesized powders of Al2O3and 3NiAl. The advantage of this process is that it allows very quick densification to near theoretical density and inhibition grain growth. Nanocrystalline materials have received much attention as advanced engineering materials with improved physical and mechanical properties. The relative density of the composite was 97%. The average Vickers hardness and fracture toughness values obtained were 804 kg/mm2and 7.5 MPa⋅m1/2, respectively.

Sign in / Sign up

Export Citation Format

Share Document