scholarly journals Process Behavior of Short Glass Fiber Filled Systems during Powder Bed Fusion and Its Effect on Part Dimensions

Polymers ◽  
2021 ◽  
Vol 13 (18) ◽  
pp. 3144
Author(s):  
Lydia Lanzl ◽  
Dietmar Drummer
Keyword(s):  
Glass Fiber ◽  
Laser Energy ◽  
Powder Bed Fusion ◽  
Filled Polymers ◽  
Neat Polymer ◽  
Powder Bed ◽  
Polymer Systems ◽  
Wide Range ◽  
Process Behavior ◽  
Strength And Stiffness

In powder bed fusion of polymers, filled systems can provide a wide range of part properties, which is still a deficit in additive manufacturing, as the material variety is limited. Glass fiber filled polymers provide a higher strength and stiffness in parts; nevertheless, the process behavior differs from neat polymer systems. In this study, the optical properties and their effect on the part dimensions are analyzed. A higher glass fiber content leads to an increased absorption of laser energy, while the specific heat capacity decreases. This results in larger part dimensions due to higher energy input into the powder bed. The aim of the study is to gain process understanding in terms of ongoing mechanisms during processing filled systems on the one hand and to derive strategies for filled polymer systems in powder bed fusion on the other hand.

scholarly journals Influence of Laser Energy Input and Shielding Gas Flow on Evaporation Fume during Laser Powder Bed Fusion of Zn Metal

Materials ◽  
2021 ◽  
Vol 14 (10) ◽  
pp. 2677
Author(s):  
Yu Qin ◽  
Jinge Liu ◽  
Yanzhe Chen ◽  
Peng Wen ◽  
Yufeng Zheng ◽  
...  
Keyword(s):  
Energy Input ◽  
Gas Flow ◽  
Evaporation Rate ◽  
Laser Energy ◽  
Circulation System ◽  
Powder Bed Fusion ◽  
Shielding Gas ◽  
Laser Powder Bed Fusion ◽  
Conservation Of Energy ◽  
Powder Bed

Laser powder bed fusion (LPBF) of Zn-based metals exhibits prominent advantages to produce customized biodegradable implants. However, massive evaporation occurs during laser melting of Zn so that it becomes a critical issue to modulate laser energy input and gas shielding conditions to eliminate the negative effect of evaporation fume during the LPBF process. In this research, two numerical models were established to simulate the interaction between the scanning laser and Zn metal as well as the interaction between the shielding gas flow and the evaporation fume, respectively. The first model predicted the evaporation rate under different laser energy input by taking the effect of evaporation on the conservation of energy, momentum, and mass into consideration. With the evaporation rate as the input, the second model predicted the elimination effect of evaporation fume under different conditions of shielding gas flow by taking the effect of the gas circulation system including geometrical design and flow rate. In the case involving an adequate laser energy input and an optimized shielding gas flow, the evaporation fume was efficiently removed from the processing chamber during the LPBF process. Furthermore, the influence of evaporation on surface quality densification was discussed by comparing LPBF of pure Zn and a Titanium alloy. The established numerical analysis not only helps to find the adequate laser energy input and the optimized shielding gas flow for the LPBF of Zn based metal, but is also beneficial to understand the influence of evaporation on the LPBF process.

scholarly journals An Overview of Additive Manufacturing Technologies—A Review to Technical Synthesis in Numerical Study of Selective Laser Melting

Materials ◽  
2020 ◽  
Vol 13 (17) ◽  
pp. 3895 ◽  
Author(s):  
Abbas Razavykia ◽  
Eugenio Brusa ◽  
Cristiana Delprete ◽  
Reza Yavari
Keyword(s):  
Numerical Simulation ◽  
Additive Manufacturing ◽  
Selective Laser Melting ◽  
Powder Bed Fusion ◽  
Laser Melting ◽  
Powder Bed ◽  
Part Quality ◽  
Melt Pool ◽  
Wide Range ◽  
Am Processes

Additive Manufacturing (AM) processes enable their deployment in broad applications from aerospace to art, design, and architecture. Part quality and performance are the main concerns during AM processes execution that the achievement of adequate characteristics can be guaranteed, considering a wide range of influencing factors, such as process parameters, material, environment, measurement, and operators training. Investigating the effects of not only the influential AM processes variables but also their interactions and coupled impacts are essential to process optimization which requires huge efforts to be made. Therefore, numerical simulation can be an effective tool that facilities the evaluation of the AM processes principles. Selective Laser Melting (SLM) is a widespread Powder Bed Fusion (PBF) AM process that due to its superior advantages, such as capability to print complex and highly customized components, which leads to an increasing attention paid by industries and academia. Temperature distribution and melt pool dynamics have paramount importance to be well simulated and correlated by part quality in terms of surface finish, induced residual stress and microstructure evolution during SLM. Summarizing numerical simulations of SLM in this survey is pointed out as one important research perspective as well as exploring the contribution of adopted approaches and practices. This review survey has been organized to give an overview of AM processes such as extrusion, photopolymerization, material jetting, laminated object manufacturing, and powder bed fusion. And in particular is targeted to discuss the conducted numerical simulation of SLM to illustrate a uniform picture of existing nonproprietary approaches to predict the heat transfer, melt pool behavior, microstructure and residual stresses analysis.

scholarly journals Control of Crystallographic Texture and Mechanical Properties of Hastelloy-X via Laser Powder Bed Fusion

Crystals ◽  
2021 ◽  
Vol 11 (9) ◽  
pp. 1064
Author(s):  
Shinya Hibino ◽  
Tsubasa Todo ◽  
Takuya Ishimoto ◽  
Ozkan Gokcekaya ◽  
Yuichiro Koizumi ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Process Parameters ◽  
Crystallographic Texture ◽  
Lamellar Microstructure ◽  
Powder Bed Fusion ◽  
Laser Powder Bed Fusion ◽  
Hastelloy X ◽  
Single Crystalline ◽  
Powder Bed ◽  
Wide Range

The influence of various laser powder bed fusion (LPBF) process parameters on the crystallographic textures and mechanical properties of a typical Ni-based solid-solution strengthened alloy, Hastelloy-X, was examined. Samples were classified into four groups based on the type of crystallographic texture: single crystalline-like microstructure with <100>//build direction (BD) (<100>-SCM), single crystalline-like microstructure with <110>//BD (<110>-SCM), crystallographic lamellar microstructure (CLM), or polycrystalline microstructure (PCM). These four crystallographic textures were realized in Hastelloy-X for the first time here to the best of our knowledge. The mechanical properties of the samples varied depending on their texture. The tensile properties were affected not only by the Schmid factor but also by the grain size and the presence of lamellar boundaries (grain boundaries). The lamellar boundaries at the interface between the <110>//BD oriented main layers and the <100>//BD-oriented sub-layers of CLM contributed to the resistance to slip transmission and the increased proof stress. It was possible to control a wide range of crystallographic microstructures via the LPBF process parameters, which determines the melt pool morphology and solidification behavior.

Effect Ultrasonic Nanocrystal Surface Modification (UNSM) Treatment on Fatigue Strength of Additive Manufactured UNS S31603

2020 ◽  
Author(s):  
Young Sik Pyun ◽  
Ruslan Karimbaev ◽  
Seimi Choi ◽  
Jun Suek Ro ◽  
Choong Ho Sanseong ◽  
...  
Keyword(s):  
Surface Modification ◽  
Additive Manufacturing ◽  
Fatigue Strength ◽  
Power Plant ◽  
Nuclear Power Plant ◽  
Nuclear Power ◽  
Complex Geometry ◽  
Powder Bed Fusion ◽  
Powder Bed ◽  
Wide Range

Abstract Additive Manufacturing (AM) which is also known as metal 3D printing technique is one of the promising manufacturing processes due to the capability to process a complex geometry component. This is implemented in wide range of applications in various industries such as automotive, aerospace, power plants, etc. The aging nuclear power plant components and the obsolescence of those components has become a concern in this industry, and AM has come as an alternative solution for this matter. The Board on Pressure and Technology Codes and Standards (BPTCS) and Board on Nuclear Codes and Standards (BNCS) Special Committees started to study the application of Powder Bed Fusion (PBF) technique for pressure retaining equipment made from UNS S31603. Also, later Korean International Working Group (KIWG) was also started a Task Group on Additive Manufacturing for Valves which focusing on Powder Bed Fusion (PBF) and Direct Energy Disposition (DED) process for pressure-retaining valve manufacturing especially for nuclear power plant application with the same material. However, the poor mechanical properties and performance, especially fatigue strength of AM materials become a concern due to the defects and flaws as the results of layering and multiple interfaces and welding related discontinuities. In this study, the fatigue strength of PBF and DED manufactured and Ultrasonic Nanocrystal Surface Modification (UNSM) treated UNS S31603 austenitic stainless steel was investigated.

scholarly journals Effect of Laser Energy Density on the Microstructure andTexture Evolution of Hastelloy-X Alloy Fabricated by Laser Powder Bed Fusion

Materials ◽  
2021 ◽  
Vol 14 (15) ◽  
pp. 4305
Author(s):  
Shuzhe Zhang ◽  
Yunpei Lei ◽  
Zhen Chen ◽  
Pei Wei ◽  
Wenjie Liu ◽  
...  
Keyword(s):  
Grain Size ◽  
Energy Density ◽  
Electron Backscatter Diffraction ◽  
Laser Energy ◽  
Primary Dendrite ◽  
Powder Bed Fusion ◽  
Laser Powder Bed Fusion ◽  
Hastelloy X ◽  
Powder Bed ◽  
Average Grain Size

It is of great importance to study the microstructure and textural evolution of laser powder bed fusion (LPBF) formed Hastelloy-X alloys, in order to establish a close relationship between the process, microstructure, and properties through the regulation of the Hastelloy-X formation process parameters. In this paper, components of a Hastelloy-X alloy were formed with different laser energy densities (also known as the volume energy density VED). The densification mechanism of Hastelloy-X was studied, and the causes of defects, such as pores and cracks, were analyzed. The influence of different energy densities on grain size, texture, and orientation was investigated using an electron backscatter diffraction technique. The results show that the average grain size, primary dendrite arm spacing, and number of low angle grain boundaries increased with the increase of energy density. At the same time, the VED can strengthen the texture. The textural intensity increases with the increase of energy density. The best mechanical properties were obtained at the VED of 96 J·mm−3.

scholarly journals Mechanical behaviour of additively manufactured lunar regolith simulant components

2018 ◽  
Vol 233 (8) ◽  
pp. 1629-1644 ◽  
Author(s):  
Athanasios Goulas ◽  
Jon GP Binner ◽  
Daniel S Engstrøm ◽  
Russell A Harris ◽  
Ross J Friel
Keyword(s):  
Compressive Strength ◽  
Additive Manufacturing ◽  
Mechanical Behaviour ◽  
Laser Energy ◽  
Lunar Regolith ◽  
Powder Bed Fusion ◽  
Powder Bed ◽  
Material Sources ◽  
Lunar Regolith Simulant

Additive manufacturing and its related techniques have frequently been put forward as a promising candidate for planetary in-situ manufacturing, from building life-sustaining habitats on the Moon to fabricating various replacements parts, aiming to support future extra-terrestrial human activity. This paper investigates the mechanical behaviour of lunar regolith simulant material components, which is a potential future space engineering material, manufactured by a laser-based powder bed fusion additive manufacturing system. The influence of laser energy input during processing was associated with the evolution of component porosity, measured via optical and scanning electron microscopy in combination with gas expansion pycnometry. The compressive strength performance and Vickers micro-hardness of the components were analysed and related back to the processing history and resultant microstructure of the lunar regolith simulant build material. Fabricated structures exhibited a relative porosity of 44–49% and densities ranging from 1.76 to 2.3 g cm−3, with a maximum compressive strength of 4.2 ± 0.1 MPa and elastic modulus of 287.3 ± 6.6 MPa, the former is comparable to a typical masonry clay brick (3.5 MPa). The additive manufacturing parts also had an average hardness value of 657 ± 14 HV0.05/15, better than borosilicate glass (580 HV). This study has shed significant insight into realising the potential of a laser-based powder bed fusion additive manufacturing process to deliver functional engineering assets via in-situ and abundant material sources that can be potentially used for future engineering applications in aerospace and astronautics.

scholarly journals Process Optimization and Microstructure Analysis to Understand Laser Powder Bed Fusion of 316L Stainless Steel

Metals ◽  
2021 ◽  
Vol 11 (5) ◽  
pp. 832
Author(s):  
Nathalia Diaz Vallejo ◽  
Cameron Lucas ◽  
Nicolas Ayers ◽  
Kevin Graydon ◽  
Holden Hyer ◽  
...  
Keyword(s):  
Stainless Steel ◽  
Energy Density ◽  
Cellular Structure ◽  
316L Stainless Steel ◽  
Powder Bed Fusion ◽  
Laser Powder Bed Fusion ◽  
Powder Bed ◽  
Wide Range ◽  
Scan Speed ◽  
Hatch Spacing

The microstructural development of 316L stainless steel (SS) was investigated over a wide range of systematically varied laser powder bed fusion (LPBF) parameters, such as laser power, scan speed, hatch spacing and volumetric energy density. Relative density, melt pool width and depth, and the size of sub-grain cellular structure were quantified and related to the temperature field estimated by Rosenthal solution. Use of volumetric energy density between 46 and 127 J/mm3 produced nearly fully dense (≥99.8%) samples, and this included the best parameter set: power = 200 W; scan speed = 800 mm/s; hatch spacing = 0.12 mm; slice thickness = 0.03; energy density = 69 J/mm3). Cooling rate of 105 to 107 K/s was estimated base on the size of cellular structure within melt pools. Using the optimized LPBF parameters, the as-built 316L SS had, on average, yield strength of 563 MPa, Young’s modulus of 179 GPa, tensile strength of 710 MPa, and 48% strain at failure.

scholarly journals Effects of Different Substrates on the Formability and Densification Behaviors of Cemented Carbide Processed by Laser Powder Bed Fusion

Materials ◽  
2021 ◽  
Vol 14 (17) ◽  
pp. 5027
Author(s):  
Decheng Liu ◽  
Wen Yue ◽  
Jiajie Kang ◽  
Chengbiao Wang
Keyword(s):  
Crack Formation ◽  
Laser Energy ◽  
Cutting Tools ◽  
Cemented Carbide ◽  
Powder Bed Fusion ◽  
Laser Powder Bed Fusion ◽  
Powder Bed ◽  
Energy Inputs ◽  
High Laser Energy ◽  
Mold Fabrication

Cemented carbide materials are widely applied in cutting tools, drill tools, and mold fabrication due to their superior hardness and wear resistance. Producing cemented carbide parts via the laser powder bed fusion (L-PBF) method has the advantage of fabricating complex structures with a rapid manufacturing speed; however, they were underdeveloped due to their low density and crack formation on the blocks. This work studied the effect of different substrates including 316L substrates, Ni200 substrates, and YG15 substrates on the forming quality of WC-17Co parts fabricated by L-PBF, with the aim of finding the optimal substrate for fabrication. The results revealed that the Ni200 substrates had a better wettability for the single tracks formation than other substrates, and bonding between the built block and the Ni200 substrate was firm without separation during processing with a large range of laser energy inputs. This guaranteed the fabrication of a relatively dense block with fewer cracks. Although the high laser energy input that led to fine crack formation on the blocks formed on the Ni200 substrate, it was found to be better suited to restricting cracks than other substrates.

scholarly journals Machinability of INCONEL718 Alloy with a Porous Microstructure Produced by Laser Melting Powder Bed Fusion at Higher Energy Densities

Materials ◽  
2020 ◽  
Vol 13 (24) ◽  
pp. 5730
Author(s):  
Paul Wood ◽  
Antonio Díaz-Álvarez ◽  
José Díaz-Álvarez ◽  
María Henar Miguélez ◽  
Alexis Rusinek ◽  
...  
Keyword(s):  
Energy Density ◽  
Laser Energy ◽  
Cutting Speed ◽  
Machining Process ◽  
Laser Energy Density ◽  
Powder Bed Fusion ◽  
Laser Melting ◽  
Powder Bed ◽  
Orthogonal Turning ◽  
Different Levels

Products produced by additive manufacturing (AM) seek to exploit net shape manufacturing by eliminating or minimizing post-process stages such as machining. However, many applications which include turbo machinery components with tight dimensional tolerances and a smooth surface finish will require at least a light machine finishing stage. This paper investigates the machinability of the additively fabricated INCONEL718 (IN718) alloy produced by laser melting powder bed fusion (LM-PBF) with different levels of spherical porosity in the microstructure. The literature suggests that the band width for laser energy density, which combines the various scan process parameters to obtain a low spherical type porosity in the LM-PBF IN718 alloy (~1%), has wide breadth. With the increasing laser energy density and above a threshold, there is a rapid increase in the spherical pore size. In this paper, three tube samples each with different levels of spherical porosity were fabricated by varying the laser energy density for LM-PBF of the IN718 alloy within the stable and higher energy density range and the porosity measured. A low laser energy density was avoided due to balling up, which promotes highly irregular lack of fusion defects and poor consolidation within the alloy microstructure. An orthogonal turning test instrumented, with a three-component dynamometer to measure the cutting forces, was performed on AM produced IN718 tube samples under light cut conditions to simulate a finish machining process. The orthogonal turning tests were also performed on a tube sample obtained from the wrought extruded stock. The machining process parameters, which were studied include varying the cutting speed at three levels, at a fixed feed and under dry cut conditions for a short duration to avoid the tool wear. The results obtained were discussed and a notable finding was the higher rate of built-up-edge formation on the tool tip from the AM samples with a higher porosity and especially at a higher cutting speed. The paper also discusses the mechanisms that underpin the findings.

Sign in / Sign up

Export Citation Format

Share Document