scholarly journals A Review on the Hydrodynamics of Taylor Flow in Microchannels: Experimental and Computational Studies

Processes ◽  
2021 ◽  
Vol 9 (5) ◽  
pp. 870
Author(s):  
Amin Etminan ◽  
Yuri S. Muzychka ◽  
Kevin Pope

Taylor flow is a strategy-aimed flow to transfer conventional single-phase into a more efficient two-phase flow resulting in an enhanced momentum/heat/mass transfer rate, as well as a multitude of other advantages. To date, Taylor flow has focused on the processes involving gas–liquid and liquid–liquid two-phase systems in microchannels over a wide range of applications in biomedical, pharmaceutical, industrial, and commercial sectors. Appropriately micro-structured design is, therefore, a key consideration for equipment dealing with transport phenomena. This review paper highlights the hydrodynamic aspects of gas–liquid and liquid–liquid two-phase flows in microchannels. It covers state-of-the-art experimental and numerical methods in the literature for analyzing and simulating slug flows in circular and non-circular microchannels. The review’s main objective is to identify the considerable opportunity for further development of microflows and provide suggestions for researchers in the field. Available correlations proposed for the transition of flow patterns are presented. A review of the literature of flow regime, slug length, and pressure drop is also carried out.

2005 ◽  
Vol 127 (4) ◽  
pp. 479-486
Author(s):  
Bin Liu ◽  
Mauricio Prado

For any pumping artificial lift system in the petroleum industry, the free gas significantly affects the performance of the pump and the system above the pump. A model, though not a complete two-phase flow model, has been developed for the effective prediction of separation efficiency across a wide range of production conditions. The model presented is divided into two main parts, the single-phase flow-field solution and the bubble-tracking method. The first part of the model solves the single-phase liquid flow field using the computational fluid dynamics approach. Then, a simple bubble-tracking method was applied to estimate the down-hole natural separation efficiency for two-phase flow. A comparison between the results of the model and the experimental data was conducted. It shows a very good agreement with the experimental data for lower gas void fractions (bubble flow regime).


Author(s):  
Christian Weinmu¨ller ◽  
Dimos Poulikakos

Microfluidics has experienced a significant increase in research activities in recent years with a wide range of applications emerging, such as micro heat exchangers, energy conversion devices, microreactors, lab-on-chip devices and micro total chemical analysis systems (μTAS). Efforts to enhance or extend the performance of single phase microfluidic devices are met by two-phase flow systems [1, 2]. Essential for the design and control of microfluidic systems is the understanding of the fluid/hydrodynamic behavior, especially pressure drop correlations. These are well established for single phase flow, however, analytical correlations for two-phase flow only reflect experimentally obtained values within an accuracy of ± 50% [3, 4]. The present study illustrates the effect of two-phase flow regimes on the pressure drop. Experimental measurement data is put into relation of calculated values based on established correlations of Lockhart-Martinelli with Chisholm modifications for macroscopic flows [5, 6] and Mishima-Hibiki modifications for microscale flows [7]. Further, the experimental pressure drop data is superimposed onto two-phase flow maps to identify apparent correlations of pressure drop abnormalities and flow regimes. The experiments were conducted in a square microchannel with a width of 200 μm. Optical access is guaranteed by an anodically bonded glass plate on a MEMS fabricated silicon chip. Superficial velocities range from 0.01 m/s to 1 m/s for the gas flow and from 0.0001 m/s to 1 m/s for the liquid flow with water as liquid feed and CO2 as gas. The analysis of the flow regimes was performed by imaging the distinct flow regimes by laser induced fluorescence microscopy, employing Rhodamine B as the photosensitive dye. The pressure drop was synchronically recorded with a 200 mbar, 2.5 bar and 25 bar differential pressure transmitter and the data was exported via a LabView based software environment, see Figure 1. Figure 2 illustrates the experimentally obtained pressure drop in comparison to the calculated values based on the Lockhard-Martinelli correlation with the Chisholm modification and the Mishima-Hibiki modification. For both cases the predications underestimate the two-phase pressure drop by more than 50%. Nevertheless, the regression of the experimental data has an offset of linear nature. Two-phase flow is assigned to flow regime maps of bubbly, wedging, slug or annular flow defined by superficial gas and liquid velocities. In Figure 3 the pressure drop is plotted as a surface over the corresponding flow regime map. Transition lines indicate a change of flow regimes enclosing an area of an anticline in the pressure data. In the direct comparison between the calculated and the measured values, the two surfaces show a distinct deviation. Especially, the anticline of the experimental data is not explained by the analytical correlations. Figure 4 depicts the findings of Figure 3 at a constant superficial velocity of 0.0232 m/s. The dominant influence of the flow regimes on the pressure drop becomes apparent, especially in the wedging flow regime. The evident deviation of two-phase flow correlations for the pressure drop is based on omitting the influence of the flow regimes. In conclusion, the study reveals a strong divergence of pressure drop measurements in microscale two-phase flow from established correlations of Lockhart-Martinelli and recognized modifications. In reference to [8, 9], an analytical model incorporating the flow regimes and, hence, predicting the precise pressure drop would be of great benefit for hydrodynamic considerations in microfluidics.


Author(s):  
W. P. Chang ◽  
Dohee Hahn

An algorithm for sodium boiling is developed in order to extend the applicability of SSC-K, which is a main system analysis code for the KALIMER (Korea Advanced LIquid MEtal Reactor) conceptual design. As the capability of the current SSC-K version is limited to simulation of only a single-phase sodium flow, its applicable range should not be enough to assess the fuel integrity under some of HCDA (Hypothetical Core Disruptive Accident) initiating events where sodium boiling is anticipated. The two-phase flow model similar to that used for the light water system is known to be no more effective directly to liquid metal reactors, because the phenomena observed between two reactor coolant systems are definitely different. The developing algorithm is based on a multiple-bubble slug ejection model, which allows a finite number of bubbles in a channel at any time. The present work is a continuous effort following the former study to confirm a qualitative acceptance on the model. Since the model has been applied only to the active fuel region in the former study, a part of its qualification seems to have already been demonstrated. For its application to the whole KALIMER core channel, however, the model needs to be examined the applicability to the fuel regions other than the active fuel. The present study primarily focuses on that point. In a result, although the model may be improved in a sense through the present study over the previous modeling, a clear limitation is also confirmed with the validity of the model. The further development, therefore, is required for this model to achieve its goal by resolving such limitations.


1990 ◽  
Vol 22 (3-4) ◽  
pp. 299-306 ◽  
Author(s):  
Keisuke Hanaki ◽  
Tomonori Matsuo ◽  
Katsuo Kumazaki

Cafeteria wastewater containing about 30% of lipid on COD basis was treated at 20°C by laboratory-scale anaerobic filter in single-phase system and two-phase systems. Stable COD removal (about 80%) was achieved in spite of large fluctuation in influent COD concentration (normal range of 1,300 - 2,500 mg−l) both in the single-phase system (hydraulic retention time (HRT) longer than 1.3 d) and in the two-phase system (HRT longer than 3.3 d). The single-phase system gave better effluent quality than the two-phase system because the former entrapped suspended solids better than the latter. However, material balance revealed that methane conversion from removed COD was higher in the two-phase system than the single-phase system. The single-phase system perhaps removed lipids by entrapment with filter media without biodegradation, and this might cause clogging problems in long-term operation. The two-phase system is recommended since it degrades lipids better than the single-phase system.


2020 ◽  
Vol 19 (07) ◽  
pp. 2050024
Author(s):  
V. G. Povarov ◽  
A. A. Keresten

A new method of calculation of equilibrium compositions of single-phase multicomponent systems in a wide range of temperatures, pressures, and elemental compositions is proposed. It is based on the minimization of the integral characteristic of the slope of the thermodynamic potential surface in the space of coordinates of chemical reactions. The proposed algorithm is applied to the definition of area of the thermodynamic stability of freons in volcanic gases and to the construction of the equilibrium profiles of the height distribution of sulphur-containing components of Venusian atmosphere.


2017 ◽  
Vol 62 (4) ◽  
pp. 2029-2043
Author(s):  
G.-Z. Quan ◽  
X. Wang ◽  
Y.-L. Li ◽  
L. Zhang

AbstractDynamic softening behaviors of a promising biomedical Ti-13Nb-13Zr alloy under hot deformation conditions across dual phaseα+βand single phaseβregions were quantitatively characterized by establishing corresponding dynamic recovery (DRV) and dynamic recrystallization (DRX) kinetic models. A series of wide range hot compression tests on a Gleeble-3500 thermo-mechanical physical simulator were implemented under the strain rate range of 0.01-10 s−1and the temperature range of 923-1173 K. The apparent differences of flow stress curves obtained in dual phaseα+βand single phaseβregions were analyzed in term of different dependence of flow stress to temperature and strain rate and different microstructural evolutions. Two typical softening mechanisms about DRV and DRX were identified through the variations of a series of stress-strain curves acquired from these compression tests. DRX is the dominant softening mechanism in dual phaseα+βrange, while DRV is the main softening mechanism in single phaseβrange. The DRV kinetic model for single phaseβregion and the DRX kinetic model for dual phaseα+βregion were established respectively. In addition, the microstructures of the compressed specimens were observed validating the softening mechanisms accordingly.


2021 ◽  
Vol 39 (2) ◽  
pp. 390-402
Author(s):  
Yanán Camaraza-Medina

This paper presents the main results of the research developed by the author in his postdoctoral investigations on heat transfer calculations during film condensation inside tubes. The elements studied are combined in an analysis expression that provides a reasonable fit with the available experimental data, which includes a total of 22 fluids, including water, refrigerants and a wide range of organic substances, which condense inside horizontal, inclined and vertical tubes. These experimental data were obtained from the reports of 33 sources. Available data covers tube diameters from 2 to 50 mm, mass flow rates from 3 to 850 kg/(m2s), reduced pressures ranging from 0.0008 to 0.91, values for single-phase from 1 to , Reynolds number for two-phase from 900 to 594390, Reynolds number for single-phase from 65 to 84950 and vapor quality from 0.01 to 0.99. The mean deviation found for the analyzed data for horizontal tubes was 13.4%, while for the inclined and vertical tubes data the mean deviation was 14.9%. In all cases, the agreement of the proposed model is good enough to be considered satisfactory for practical design.


2004 ◽  
Vol 856 ◽  
Author(s):  
Susan Babinec ◽  
Huiqing Zhang ◽  
Andrew Talik ◽  
Valeriy Ginzburg

ABSTRACTThe conductivity and mechanical stiffness of ethylene-oxide based Li+ conducting solid polymer electrolytes (SPE) were measured and compared for a variety of single- and two-phase systems. Our objective was to determine whether there are simple correlations between these two properties despite the fact that these systems are truly complex. Results show that molecular architecture dominates both transport and mechanical behavior of single phase systems, thereby eliminating broad correlations. Conductivity was additionally found to require not only facile local chain dynamics but also a sufficient concentration of vacancies, as per the site hopping model. Two phase systems also show complex behaviors, but offer a broader range of both conductivity and stiffness values, and good conductivity/stiffness correlations.


2020 ◽  
Vol 2020 ◽  
pp. 1-11 ◽  
Author(s):  
Yuhuan Gong ◽  
Yuchang Mo

Currently, mobile edge computing (MEC) is one of the most popular techniques used to respond to real-time services from a wide range of mobile terminals. Compared with single-phase systems, commercial services in MEC can be modeled as phased-mission systems (PMS) and are much more complex, because of the dependencies across the phases. Over the past decade, researchers have proposed a set of new algorithms based on BDD for fault tree analysis of a wide range of PMS with various mission requirements and failure behaviors. The analysis to be performed on a fault tree can be either qualitative or quantitative. For the quantitative fault tree analysis of PMS by means of BDD, much work has been conducted. However, for the qualitative fault tree analysis of PMS by means of BDD, no much related work can be found. In this paper, we have presented some efficient methods to calculate the MCS encoding by a PMS BDD. Firstly, three kinds of redundancy relations-inclusive relation, internal-implication relation, and external-implication relation-within the cut set are identified, which prevent the cut set from being minimal cut set. Then, three BDD operations, IncRed, InImpRed, and ExImpRed, are developed, respectively, for the elimination of these redundancy relations. Using some proper combinations of these operations, MCS can be calculated correctly. As an illustration, some experimental results on a benchmark MEC system are given.


Sign in / Sign up

Export Citation Format

Share Document