scholarly journals On-Orbit Radiance Calibration of Nighttime Sensor of LuoJia1-01 Satellite Based on Lunar Observations

2019 ◽  
Vol 11 (18) ◽  
pp. 2183
Author(s):  
Yonghua Jiang ◽  
Yingrui Shi ◽  
Litao Li ◽  
Miaozhong Xu ◽  
Wenzhi Zeng ◽  
...  
Keyword(s):  
Remote Sensing ◽  
Near Infrared ◽  
Radiometric Calibration ◽  
Infrared Sensors ◽  
Basic Premise ◽  
Sensing Applications ◽  
Ground Object ◽  
Remote Sensing Satellite ◽  
One Year ◽  
The Stability

The high-resolution nighttime light (NTL) data of the LuoJia1-01 NTL remote sensing satellite has enriched the available data of NTL remote sensing applications. The radiance calibration used as a reference to convert the digital number (DN) recorded by the nighttime sensor into the radiance of the corresponding ground object is the basic premise to the effective application of the NTL data. Owing to the lack of on-board calibration equipment and the absence of an absolute radiometric calibration light source at night, it is difficult for LuoJia1-01 to carry out on-orbit radiance calibration. The moon, as an exoatmospheric stable radiation source, is widely used for the radiometric calibration of remote sensing satellite sensors and to monitor the stability of the visible and near-infrared sensors. This study, based on lunar observation of the LuoJia1-01 NTL sensor, focused on on-orbit radiometric calibration and included monitoring changes in the nighttime sensor radiometric response for nearly a year by using the Robotic Lunar Observatory (ROLO) lunar irradiance model (Version 311 g). The results showed that: (1) the consistency of the radiometric calibration results based on the ROLO model and the laboratory calibration results of LuoJia1-01 exceeded 90%; (2) the nighttime sensor of LuoJia1-01 radiometric response underwent approximately 6% degradation during the observation period of nearly one year (353 days).

scholarly journals Multispectral Sensor Calibration and Characterization for sUAS Remote Sensing

Sensors ◽  
2019 ◽  
Vol 19 (20) ◽  
pp. 4453 ◽  
Author(s):  
Mamaghani ◽  
Salvaggio
Keyword(s):  
Remote Sensing ◽  
Near Infrared ◽  
Laboratory Method ◽  
Sensor Calibration ◽  
Radiometric Calibration ◽  
End User ◽  
Sensing Applications ◽  
A Value ◽  
Remote Sensing Applications

This paper focuses on the calibration of multispectral sensors typically used for remote sensing. These systems are often provided with "factory" radiometric calibration and vignette correction parameters. These parameters, which are assumed to be accurate when the sensor is new, may change as the camera is utilized in real-world conditions. As a result, regular calibration and characterization of any sensor should be conducted. An end-user laboratory method for computing both the vignette correction and radiometric calibration function is discussed in this paper. As an exemplar, this method for radiance computation is compared to the method provided by MicaSense for their RedEdge series of sensors. The proposed method and the method provided by MicaSense for radiance computation are applied to a variety of images captured in the laboratory using a traceable source. In addition, a complete error propagation is conducted to quantify the error produced when images are converted from digital counts to radiance. The proposed methodology was shown to produce lower errors in radiance imagery. The average percent error in radiance was −10.98%, −0.43%, 3.59%, 32.81% and −17.08% using the MicaSense provided method and their "factory" parameters, while the proposed method produced errors of 3.44%, 2.93%, 2.93%, 3.70% and 0.72% for the blue, green, red, near infrared and red edge bands, respectively. To further quantify the error in terms commonly used in remote sensing applications, the error in radiance was propagated to a reflectance error and additionally used to compute errors in two widely used parameters for assessing vegetation health, NDVI and NDRE. For the NDVI example, the ground reference was computed to be 0.899 ± 0.006, while the provided MicaSense method produced a value of 0.876 ± 0.005 and the proposed method produced a value of 0.897 ± 0.007. For NDRE, the ground reference was 0.455 ± 0.028, MicaSense method produced 0.239 ± 0.026 and the proposed method produced 0.435 ± 0.038.

scholarly journals Deep learning para la clasificación de usos de suelo agrícola con Sentinel-2

2020 ◽  
pp. 35
Author(s):  
M. Campos-Taberner ◽  
F.J. García-Haro ◽  
B. Martínez ◽  
M.A. Gilabert
Keyword(s):  
Remote Sensing ◽  
Deep Learning ◽  
Near Infrared ◽  
Spatial Information ◽  
Learning Algorithm ◽  
Support Vector ◽  
Sensing Applications ◽  
Learning Techniques ◽  
Remote Sensing Applications ◽  
Sentinel 2

<p class="p1">The use of deep learning techniques for remote sensing applications has recently increased. These algorithms have proven to be successful in estimation of parameters and classification of images. However, little effort has been made to make them understandable, leading to their implementation as “black boxes”. This work aims to evaluate the performance and clarify the operation of a deep learning algorithm, based on a bi-directional recurrent network of long short-term memory (2-BiLSTM). The land use classification in the Valencian Community based on Sentinel-2 image time series in the framework of the common agricultural policy (CAP) is used as an example. It is verified that the accuracy of the deep learning techniques is superior (98.6 % overall success) to that other algorithms such as decision trees (DT), k-nearest neighbors (k-NN), neural networks (NN), support vector machines (SVM) and random forests (RF). The performance of the classifier has been studied as a function of time and of the predictors used. It is concluded that, in the study area, the most relevant information used by the network in the classification are the images corresponding to summer and the spectral and spatial information derived from the red and near infrared bands. These results open the door to new studies in the field of the explainable deep learning in remote sensing applications.</p>

scholarly journals Radiometric Calibration of UAV Remote Sensing Image with Spectral Angle Constraint

2019 ◽  
Vol 11 (11) ◽  
pp. 1291 ◽  
Author(s):  
Kaiqiu Xu ◽  
Yan Gong ◽  
Shenghui Fang ◽  
Ke Wang ◽  
Zhiheng Lin ◽  
...  
Keyword(s):  
Remote Sensing ◽  
Near Infrared ◽  
Linear Method ◽  
Radiometric Calibration ◽  
Constraint Condition ◽  
Infrared Band ◽  
Spectral Bands ◽  
Quantitative Remote Sensing ◽  
Spectral Channels ◽  
Spectral Angle

In recent years, the acquisition of high-resolution multi-spectral images by unmanned aerial vehicles (UAV) for quantitative remote sensing research has attracted more and more attention, and radiometric calibration is the premise and key to the quantification of remote sensing information. The traditional empirical linear method independently calibrates each channel, ignoring the correlation between spectral bands. However, the correlation between spectral bands is very valuable information, which becomes more prominent as the number of spectral channels increases. Based on the empirical linear method, this paper introduces the constraint condition of spectral angle, and makes full use of the information of each band for radiometric calibration. The results show that, compared with the empirical linear method, the proposed method can effectively improve the accuracy of radiometric calibration, with the improvement range of Mean Relative Percent Error (MRPE) being more than 3% in the range of visible band and within 1% in the range of near-infrared band. Besides, the method has great advantages in agricultural remote sensing quantitative inversion.

scholarly journals An Algorithm to Retrieve Total Precipitable Water Vapor in the Atmosphere from FengYun 3D Medium Resolution Spectral Imager 2 (FY-3D MERSI-2) Data

2020 ◽  
Vol 12 (21) ◽  
pp. 3469
Author(s):  
Bilawal Abbasi ◽  
Zhihao Qin ◽  
Wenhui Du ◽  
Jinlong Fan ◽  
Chunliang Zhao ◽  
...  
Keyword(s):  
Remote Sensing ◽  
Water Vapor ◽  
Near Infrared ◽  
Precipitable Water ◽  
Precipitable Water Vapor ◽  
Optical Remote Sensing ◽  
Statistical Regression ◽  
Sensing Applications ◽  
Medium Resolution ◽  
Spectral Imager

The atmosphere has substantial effects on optical remote sensing imagery of the Earth’s surface from space. These effects come through the functioning of atmospheric particles on the radiometric transfer from the Earth’s surface through the atmosphere to the sensor in space. Precipitable water vapor (PWV), CO2, ozone, and aerosol in the atmosphere are very important among the particles through their functioning. This study presented an algorithm to retrieve total PWV from the Chinese second-generation polar-orbiting meteorological satellite FengYun 3D Medium Resolution Spectral Imager 2 (FY-3D MERSI-2) data, which have three near-infrared (NIR) water vapor absorbing channels, i.e., channel 16, 17, and 18. The algorithm was improved from the radiance ratio technique initially developed for Moderate-Resolution Imaging Spectroradiometer (MODIS) data. MODTRAN 5 was used to simulate the process of radiant transfer from the ground surfaces to the sensor at various atmospheric conditions for estimation of the coefficients of ratio technique, which was achieved through statistical regression analysis between the simulated radiance and transmittance values for FY-3D MERSI-2 NIR channels. The algorithm was then constructed as a linear combination of the three-water vapor absorbing channels of FY-3D MERSI-2. Measurements from two ground-based reference datasets were used to validate the algorithm: the sun photometer measurements of Aerosol Robotic Network (AERONET) and the microwave radiometer measurements of Energy’s Atmospheric Radiation Measurement Program (ARMP). The validation results showed that the algorithm performs very well when compared with the ground-based reference datasets. The estimated PWV values come with root mean square error (RMSE) of 0.28 g/cm2 for the ARMP and 0.26 g/cm2 for the AERONET datasets, with bias of 0.072 g/cm2 and 0.096 g/cm2 for the two reference datasets, respectively. The accuracy of the proposed algorithm revealed a better consistency with ground-based reference datasets. Thus, the proposed algorithm could be used as an alternative to retrieve PWV from FY-3D MERSI-2 data for various remote sensing applications such as agricultural monitoring, climate change, hydrologic cycle, and so on at various regional and global scales.

scholarly journals Infrared detector activities at NASA Langley Research Center

2008 ◽  
Vol 1076 ◽  
Author(s):  
M. Nurul Abedin ◽  
Tamer F Refaat ◽  
Oleg V Sulima ◽  
Farzin Amzajerdian
Keyword(s):  
Remote Sensing ◽  
Near Infrared ◽  
Infrared Detector ◽  
Avalanche Photodiode ◽  
Low Noise ◽  
Focal Plane Arrays ◽  
Research Center ◽  
Single Element ◽  
Sensing Applications ◽  
Langley Research Center

ABSTRACTInfrared detector development and characterization at NASA Langley Research Center will be reviewed. These detectors were intended for ground, airborne, and space borne remote sensing applications. Discussion will be focused on recently developed single-element infrared detector and future development of near-infrared focal plane arrays (FPA). The FPA will be applied to next generation space-based instruments. These activities are based on phototransistor and avalanche photodiode technologies, which offer high internal gain and relatively low noise-equivalent-power. These novel devices will improve the sensitivity of active remote sensing instruments while eliminating the need for a high power laser transmitter.

scholarly journals Radiometric Cross-Calibration of GF-1 PMS Sensor with a New BRDF Model

2019 ◽  
Vol 11 (6) ◽  
pp. 707 ◽  
Author(s):  
Qiyue Liu ◽  
Tao Yu ◽  
Hailiang Gao
Keyword(s):  
Calibration Method ◽  
Reference Image ◽  
Landsat 8 ◽  
Radiometric Calibration ◽  
Sensing Applications ◽  
Quantitative Remote Sensing ◽  
Calibration Accuracy ◽  
The Cross ◽  
One Year ◽  
Cross Calibration

On-orbit radiometric calibration of a space-borne sensor is of great importance for quantitative remote sensing applications. Cross-calibration is a common method with high calibration accuracy, and the core and emphasis of this method is to select the appropriate reference satellite sensor. As for the cross-calibration of high-spatial resolution and narrow-swath sensor, however, there are some scientific issues, such as large observation angles of reference image, and non-synchronization (or quasi-synchronization) between the imaging date of reference image and the date of sensor to be calibrated, which affects the accuracy of cross-calibration to a certain degree. Therefore, taking the GaoFen-1 (GF-1) Panchromatic and Multi-Spectral (PMS) sensor as an example in this research, an innovative radiometric cross-calibration method is proposed to overcome this bottleneck. Firstly, according a set of criteria, valid MODIS (Moderate Resolution Imagine Spectroradiometer) images of sunny day in one year over the Dunhuang radiometric calibration site in China are extracted, and a new and distinctive bidirectional reflectance distribution function (BRDF) model based on top-of-atmosphere (TOA) reflectance and imaging angles of the sunny day MODIS images is constructed. Subsequently, the cross-calibration of PMS sensor at Dunhuang and Golmud radiation calibration test sites is carried out by using the method presented in this paper, taking the MODIS image with large solar and observation angles and Landsat 8 Operational Land Imager (OLI) with different dates from PMS as reference. The validation results of the calibration coefficients indicate that our proposed method can acquire high calibration accuracy, and the total calibration uncertainties of PMS using MODIS as reference sensor are less than 6%.

THE APPLICATION OF REMOTE SENSING IN PRECISION AGRICULTURE

1970 ◽  
pp. 10-16
Author(s):  
S. Yu. Blokhina
Keyword(s):  
Remote Sensing ◽  
Data Storage ◽  
Spatial Resolution ◽  
Precision Agriculture ◽  
Near Infrared ◽  
Crop Yields ◽  
Temporal Frequency ◽  
Organic Matter Content ◽  
Sensing Applications ◽  
Remote Sensing Applications

The paper provides an overview of foreign literature on the remote sensing applications in precision agriculture. Remote sensing applications in precision agriculture began with sensors for soil organic matter content, and have quickly advanced to include hand held sensors to tractor or aerial or satellite mounted sensors. Wavelengths of electromagnetic radiation initially focused on a few key visible or near infrared bands, and nowadays electromagnetic wavelengths in use range from the ultraviolet to microwave portions of the spectrum. Spectral bandwidth has decreased dramatically with the advent of hyperspectral remote sensing, allowing improved analysis of crop stress, crop biophysical or biochemical characteristics and specific compounds. A variety of spectral indices have been widely implemented within various precision agriculture applications, rather than a focus on only normalized difference vegetation indices. Spatial resolution and temporal frequency of remote sensing imagery has increased significantly, allowing evaluation of soil and crop properties at fine spatial resolution at the expense of increased data storage and processing requirements. At present there is considerable interest in collecting remote sensing for operational management of soil and crop yields, as well as control over the spread of pests and weeds practically in real time.

UAV Remote Sensing Assessment of Crop Growth

2021 ◽  
Vol 87 (12) ◽  
pp. 891-899
Author(s):  
Freda Elikem Dorbu ◽  
Leila Hashemi-Beni ◽  
Ali Karimoddini ◽  
Abolghasem Shahbazi
Keyword(s):  
Remote Sensing ◽  
Unmanned Aerial Vehicle ◽  
Vegetation Index ◽  
Near Infrared ◽  
Normalized Difference Vegetation Index ◽  
Crop Growth ◽  
Infrared Sensors ◽  
Digital Elevation ◽  
Aerial Vehicle ◽  
Growth Indicators

The introduction of unmanned-aerial-vehicle remote sensing for collecting high-spatial- and temporal-resolution imagery to derive crop-growth indicators and analyze and present timely results could potentially improve the management of agricultural businesses and enable farmers to apply appropriate solution, leading to a better food-security framework. This study aimed to analyze crop-growth indicators such as the normalized difference vegetation index (NDVI), crop height, and vegetated surface roughness to determine the growth of corn crops from planting to harvest. Digital elevation models and orthophotos generated from the data captured using multispectral, red/green/blue, and near-infrared sensors mounted on an unmanned aerial vehicle were processed and analyzed to calculate the various crop-growth indicators. The results suggest that remote sensing-based growth indicators can effectively determine crop growth over time, and that there are similarities and correlations between the indicators.

X-ray diffraction and infrared characterization of Oxisols from central and southeastern Brazil

Clay Minerals ◽  
2008 ◽  
Vol 43 (4) ◽  
pp. 549-560 ◽  
Author(s):  
R. P. Nitzsche ◽  
J. B. Percival ◽  
J. K. Torrance ◽  
J. A. R. Stirling ◽  
J. T. Bowen
Keyword(s):  
Remote Sensing ◽  
Near Infrared ◽  
Microwave Remote Sensing ◽  
Short Wave ◽  
Southeastern Brazil ◽  
X Ray Diffraction ◽  
X Ray ◽  
Sensing Applications ◽  
Remote Sensing Applications

AbstractEleven Oxisols with high clay contents, 2.6–59.7 wt.% Fe2O3, and containing hematite, goethite, magnetite and maghemite, from São Paulo, Minas Gerais and Goiás, Brazil, were studied for the purpose of microwave remote sensing applications in the 0.3 to 300 GHz range. Of special interest are: the pseudosand effect caused by Fe-oxide cementation of clusters of soil particles; the mineralogy; and whether the soil magnetic susceptibility affected by ferromagnetic magnetite and maghemite interferes with microwave propagation. Quantitative mineralogical analyses were conducted using X-ray diffraction with Rietveld refinement. Visible, near infrared and short wave infrared spectroscopic analyses were used to characterize the samples qualitatively for comparison with published spectral radiometry results. Quartz (3–88%), hematite (2–36%) and gibbsite (1–40%) occurred in all soils, whereas kaolinite (2–70%) and anatase (2–13%) occurred in nine samples. Ilmenite (1–8%) was found in eight soils and goethite (2–39%) in seven. Of the ferromagnetic minerals, maghemite occurred in seven soils (1–13%) and three contained magnetite (<2%). These results will be applied to the interpretation of the effect of Fe oxides, particularly the ferromagnetic oxides, on microwave interaction with high-Fe soils, with ultimate application to the monitoring of soil water content by microwave remote sensing.

Sign in / Sign up

Export Citation Format

Share Document