scholarly journals Dual-Polarized Multi-Channel 24 GHz Radar Sensor Antenna for High Channel-to-Channel Isolation

Sensors ◽  
2020 ◽  
Vol 20 (18) ◽  
pp. 5233 ◽  
Author(s):  
Young-Jun Kim ◽  
Gunhark Noh ◽  
Han Lim Lee ◽  
Sungwook Yu
Keyword(s):  
Radiation Pattern ◽  
Printed Circuit Board ◽  
High Gain ◽  
Circuit Board ◽  
Impedance Bandwidth ◽  
Sensor Applications ◽  
Feed Network ◽  
Dual Polarized ◽  
Antenna Module ◽  
24 Ghz

This article presents a dual-polarized, high gain multi-beam and high T/Rx channel-to-channel isolation antenna module for 24 GHz sensor applications. The proposed antenna is configured to support 2-Tx and 2-Rx channels with a pair of vertically polarized (VP) radiation pattern and a pair of horizontally polarized (HP) radiation pattern. Further, each linearly polarized T/Rx antenna is configured by 2 × 4 array with a multi-layer integrated feed network, resulting in four sets of 2 × 4 array antennas fabricated within a single printed circuit board (PCB). Since multiple RF channels must be ensured with minimal interference, high antenna-to-antenna, including Tx-to-Tx, Rx-to-Rx, and Tx-to-Rx port isolations in the proposed antenna are achieved by multi-layered feed network and four sets of T-shaped magnetic walls. To verify the performance of the proposed structure, a 2-Tx and 2-Rx antenna module was fabricated at 24 GHz. The fabricated antenna showed a measured maximum 10-dB impedance bandwidth of 3.9% with a maximum measured gain of 11.7 dBi, considering both Tx and Rx. Further, the measured channel-to-channel isolations were always better than 35.6 dB at 24 GHz.

scholarly journals High Gain Triple-Band Metamaterial-Based Antipodal Vivaldi MIMO Antenna for 5G Communications

Micromachines ◽  
2021 ◽  
Vol 12 (3) ◽  
pp. 250
Author(s):  
Tale Saeidi ◽  
Idris Ismail ◽  
Sima Noghanian ◽  
Adam R. H. Alhawari ◽  
Qammer H. Abbasi ◽  
...  
Keyword(s):  
Printed Circuit Board ◽  
Multiple Input Multiple Output ◽  
High Gain ◽  
Radiation Efficiency ◽  
Circuit Board ◽  
Spiral Antenna ◽  
Mimo Antenna ◽  
High Isolation ◽  
Dual Polarized ◽  
Triple Band

This paper presents a miniaturized dual-polarized Multiple Input Multiple Output (MIMO) antenna with high isolation. The antenna meets the constraints of sub-6 GHz 5G and the smartphones’ X-band communications. A vertically polarized modified antipodal Vivaldi antenna and a horizontally polarized spiral antenna are designed and integrated, and then their performance is investigated. Three frequency bands of 3.8 GHz, 5.2 GHz, and 8.0 GHz are considered, and the proposed dual-polarized antenna is studied. High isolation of greater than 20 dB is obtained after integration of metamaterial elements, and without applying any other decoupling methods. The proposed triple-band metamaterial-based antenna has 1.6 GHz bandwidth (BW) (2.9 GHz–4.5 GHz), 13.5 dBi gain, and 98% radiation efficiency at 3.8 GHz. At 5.2 GHz it provides 1.2 GHz BW, 9.5 dBi gain, and 96% radiation efficiency. At 8.0 GHz it has 1 GHz BW, 6.75 dBi gain, and 92% radiation efficiency. Four antenna elements (with eight ports) were laid out orthogonally at the four corners of a mobile printed circuit board (PCB) to be utilized as a MIMO antenna for 5G communications. The performance of the MIMO antenna is examined and reported.

scholarly journals Wideband and High-Efficiency SIW Cavity-Backed Magneto-Electric Dipole Antenna Array

2019 ◽  
Vol 2019 ◽  
pp. 1-16
Author(s):  
Guang Sun ◽  
Yi Liu ◽  
Taolin Liu ◽  
Hu Yang
Keyword(s):  
Antenna Array ◽  
Printed Circuit Board ◽  
High Efficiency ◽  
High Gain ◽  
Dipole Antenna ◽  
Circuit Board ◽  
Impedance Bandwidth ◽  
Antenna Element ◽  
Substrate Integrated Waveguide ◽  
Printed Circuit

In this paper, a compact, wideband, and high-efficiency substrate integrated waveguide (SIW) feeding cavity-backed aperture-coupled magneto-electric (ME) dipole antenna element and its array are proposed. Firstly, an SIW cavity-backed and a modified bowtie dipole are designed for the antenna element which makes it possess a high gain and wide impedance bandwidth. The antenna element covers an impedance bandwidth of 66.3% from 10.7 to 21.3 GHz with a peak gain of 10.3 dBi. Secondly, a 4 × 4 array is designed using the proposed antenna element. And a full-corporate substrate integrated waveguide feeding network is introduced to excite the array elements for the antenna application with wide bandwidth and high efficiency. For validation, a prototype of 4 × 4 array is fabricated by standard printed circuit board (PCB) facilities and further measured. The measured −10 dB impedance bandwidth of the proposed 4 × 4 antenna array is 30% (12.75–17.25 GHz) with its gain being 18.2–20.9 dBi within the entire band. The measured maximum aperture efficiency of the antenna array is 94% at 14.92 GHz. Notably, the measured results agree well with simulations, and it shows great advantages over other similar antennas on efficiency and bandwidth.

A compact, dual-polarized patch antenna with improved Tx–Rx isolation for 2.4 GHz single frequency full-duplex applications

2020 ◽  
pp. 1-8
Author(s):  
Haq Nawaz ◽  
Muhammad Abdul Basit ◽  
Ahmad Umar Niazi
Keyword(s):  
Interference Cancellation ◽  
Printed Circuit Board ◽  
Circuit Board ◽  
Full Duplex ◽  
Single Frequency ◽  
Impedance Bandwidth ◽  
Antenna Structure ◽  
Mode Operation ◽  
Hybrid Coupler ◽  
Dual Polarized

Abstract A compact dual-polarized monostatic antenna (single radiator for transmit and receive modes) is presented with differential receive mode operation to achieve excellent interport isolation for 2.4 GHz single frequency full-duplex or in-band full-duplex applications. The presented antenna comprises three ports radiating element (patch) and a simple 3 dB/180o ring hybrid coupler has been utilized for differentially excited receive mode operation. The 3 dB/180o ring hybrid coupler acts as a self-interference cancellation (SIC) circuit for effective suppression of RF leakage from the transmit port to provide very high interport decoupling between transmit and receive ports. A compact antenna structure has been realized by using two-layered printed circuit board through vias interconnections of both receive ports of the antenna with inputs of SIC circuit. The validation model of proposed antenna offers more than 95 dB peak interport isolation. Moreover, the experimentally measured interport isolation is better than 70 dB throughout the antenna's 10 dB return-loss impedance bandwidth (BW) of 50 MHz (2.38–2.43 GHz). Furthermore, the recorded isolation is more than 80 dB in 20 MHz BW. The implemented antenna has good radiation characteristics including nice gain and low cross-polarization levels as endorsed by measurements. Same antenna structure with microstrip-T feeds can provide DC isolated ports with same interport RF isolation performance for active antenna applications. Such antenna with DC interport isolation will avoid the requirements of additional series capacitors on transmit and receive ports of antenna.

scholarly journals Wideband Dual-Polarized VHF Antenna for Space Observation Applications

Sensors ◽  
2020 ◽  
Vol 20 (15) ◽  
pp. 4351
Author(s):  
Alexandru Tatomirescu ◽  
Alina Badescu
Keyword(s):  
Radiation Pattern ◽  
Group Delay ◽  
High Gain ◽  
Antenna Element ◽  
Frequency Bandwidth ◽  
Radio Emissions ◽  
Relative Bandwidth ◽  
Pattern Stability ◽  
Dual Polarized ◽  
Delay Variation

This work presents the design for an antenna element that can be used in radio arrays for the monitoring and detecting of radio emissions from cosmic particles’ interactions in the atmosphere. For these applications, the pattern stability over frequency is the primary design goal. The proposed antenna has a high gain over a relative bandwidth of 88%, a beamwidth of 2.13 steradians, a small group delay variation and a very stable radiation pattern across the frequency bandwidth of 110 to 190 MHz. It is dual polarized and has a simple mechanical structure which is easy and inexpensive to manufacture. The measurements show that the ground has insignificant impact on the overall radiation pattern.

scholarly journals Mobile-Phone Antenna Array with Diamond-Ring Slot Elements for 5G Massive MIMO Systems

Electronics ◽  
2019 ◽  
Vol 8 (5) ◽  
pp. 521 ◽  
Author(s):  
Naser Ojaroudi Parchin ◽  
Haleh Jahanbakhsh Basherlou ◽  
Mohammad Alibakhshikenari ◽  
Yasser Ojaroudi Parchin ◽  
Yasir I. A. Al-Yasir ◽  
...  
Keyword(s):  
Mobile Phone ◽  
Antenna Array ◽  
Massive Mimo ◽  
Printed Circuit Board ◽  
High Efficiency ◽  
Mimo Systems ◽  
Circuit Board ◽  
Slot Antenna ◽  
Impedance Bandwidth ◽  
Diamond Ring

A design of mobile-phone antenna array with diamond-ring slot elements is proposed for fifth generation (5G) massive multiple-input/multiple-output (MIMO) systems. The configuration of the design consists of four double-fed diamond-ring slot antenna elements placed at different corners of the mobile-phone printed circuit board (PCB). A low-cost FR-4 dielectric with an overall dimension of 75 × 150 mm2 is used as the design substrate. The antenna elements are fed by 50-Ohm L-shaped microstrip-lines. Due to the orthogonal placement of microstrip feed lines, the diamond-ring slot elements can exhibit the polarization and radiation pattern diversity characteristic. A good impedance bandwidth (S11 ≤ −10 dB) of 3.2–4 GHz has been achieved for each antenna radiator. However, for S11 ≤ −6 dB, this value is 3–4.2 GHz. The proposed design provides the required radiation coverage of 5G smartphones. The performance of the proposed MIMO antenna design is examined using both simulation and experiment. High isolation, high efficiency and sufficient gain-level characteristics have been obtained for the proposed MIMO smartphone antenna. In addition, the calculated total active reflection coefficient (TARC) and envelope correlation coefficient (ECC) of the antenna elements are very low over the whole band of interest which verify the capability of the proposed multi-antenna systems for massive MIMO and diversity applications. Furthermore, the properties of the design in Data-mode/Talk-mode are investigated and presented.

scholarly journals High Gain and High Efficient Stacked Antenna Array with Integrated Horn for 60 GHz Communication Systems

2014 ◽  
Vol 2014 ◽  
pp. 1-8 ◽  
Author(s):  
Hamsakutty Vettikalladi ◽  
Waleed Tariq Sethi ◽  
Majeed A. Alkanhal
Keyword(s):  
Communication Systems ◽  
High Gain ◽  
Center Frequency ◽  
Impedance Bandwidth ◽  
Antenna Element ◽  
60 Ghz ◽  
Antenna Structure ◽  
High Efficient ◽  
Feed Network ◽  
Array Structure

In order to achieve wide bandwidth and high gain, we propose a stacked antenna structure having a microstrip aperture coupled feeding technique with a mounted Horn integrated on it. With optimized parameters, the single antenna element at a center frequency of 60 GHz, exhibits a wide impedance bandwidth of about 10.58% (58.9–65.25 GHz) with a gain and efficiency of 11.78 dB and 88%, respectively. For improving the gain, we designed a 2 × 2 and 4 × 4 arrays with a corporate feed network. The side lobe levels were minimized and the back radiations were reduced by making use of a reflector atλ/4distance from the corporate feed network. The2×2array structure resulted in improved gain of 15.3 dB with efficiency of 83%, while the4×4array structure provided further gain improvement of 18.07 dB with 68.3% efficiency. The proposed design is modelled in CST Microwave Studio. The results are verified using HFSS, which are found to be in good agreement.

A K-band delay line based on parasitic reduced artificial left-handed transmission line

2013 ◽  
Vol 5 (6) ◽  
pp. 709-711
Author(s):  
Hyun-Seung Lee ◽  
Eun-Gyu Lee ◽  
Choul-Young Kim
Keyword(s):  
Transmission Line ◽  
Return Loss ◽  
Printed Circuit Board ◽  
Delay Line ◽  
Circuit Board ◽  
Printed Circuit ◽  
Left Handed ◽  
24 Ghz ◽  
K Band ◽  
Interdigital Capacitors

A K-band microstrip delay line based on parasitic reduced left-handed transmission line (LHTL) with interdigital capacitors and shunt inductors is demonstrated with the aid of printed circuit board technology. The proposed delay line has ground slots under the interdigital capacitors to reduce the parasitic capacitance. The time delay of the proposed LHTLs is approximately 2.6 times larger than that of the conventional LHTLs. The input return loss of the proposed LHTL at 24 GHz is −16.9 dB and less than −10 dB from 20.5 to 26.1 GHz.

scholarly journals 2D Gain Enhancement Based on Single-Layer SIW Corrugated Technique with Slot Array Feeder

2018 ◽  
Vol 2018 ◽  
pp. 1-6
Author(s):  
Mingtuan Lin ◽  
Chenglong Lin
Keyword(s):  
Reflection Coefficient ◽  
Printed Circuit Board ◽  
Single Layer ◽  
High Gain ◽  
Circuit Board ◽  
Design Complexity ◽  
Printed Circuit ◽  
Gain Enhancement ◽  
High Gain Antenna ◽  
The Common

Novel slot-array-based SIW corrugated technique is demonstrated to achieve 2D gain enhancement, namely, sharpening the beamwidths in both E-plane and H-plane. Compared to other metallic corrugated methods to realize 2D gain enhancement, the proposed design, with SIW grooves to reduce the beamwidth in E-plane and slot array to increase the directivity in H-plane, has a lower profile, weight, and design complexity, which can be easily fabricated with the common printed circuit board (PCB) technique. A prototype is designed and fabricated, with measurement presenting a low reflection coefficient less than −10 dB from 26.4 GHz to 28.2 GHz and an enhanced gain up to 18 dB. Overall, our proposed technique will be beneficial for the design of high-gain antenna in 5G wireless terminals.

scholarly journals A Millimeter-Wave Wideband Circularly Polarized Planar Spiral Antenna Array with Unequal Amplitude Feeding Network

2021 ◽  
Vol 2021 ◽  
pp. 1-10
Author(s):  
Huakang Chen ◽  
Yu Shao ◽  
Zhangjian He ◽  
Changhong Zhang ◽  
Zhizhong Zhang
Keyword(s):  
Antenna Array ◽  
Millimeter Wave ◽  
Printed Circuit Board ◽  
Low Cost ◽  
Axial Ratio ◽  
Circuit Board ◽  
Impedance Bandwidth ◽  
Side Lobe Level ◽  
Archimedean Spiral ◽  
Circularly Polarized

A 2 × 2 wideband circularly polarized (CP) antenna array operating at millimeter wave (mmWave) band is presented. The array element is a wideband CP Archimedean spiral radiator with special-shaped ring slot. The elements are fed by an unequal amplitude (UA) feeding network based on a microstrip line (MSL) power divider. The side lobe level is improved by this UA feeding network. In addition, a cross slot is employed to isolate the elements for decoupling. A prototype is fabricated, and the measured results show that the proposed array achieves an impedance bandwidth (IBW) of 6.31 GHz (22.5% referring to 28 GHz) and an axial ratio bandwidth (ARBW) of 7.32 GHz (26.1% referring to 28 GHz). The peak gain of the proposed array is 11.3 dBic, and the gain is greater than 9.3 dBic within the whole desired band (from 25 GHz to 31 GHz). The proposed array consists of only one substrate layer and can be built by the conventional printed circuit board technology. Attributed to the characteristics of wide bandwidth, simple structure, low profile, and low cost, the proposed antenna array has a great potential in mmWave wireless communications.

scholarly journals Broadband Dual-Polarized Multidipole Antenna for Base Station Applications

2021 ◽  
Vol 2021 ◽  
pp. 1-8
Author(s):  
Yuxuan Huang ◽  
Zeqi Zhu ◽  
Shuting Cai ◽  
Xiaoming Xiong ◽  
Yuan Liu
Keyword(s):  
Radiation Pattern ◽  
Base Station ◽  
Impedance Bandwidth ◽  
Frequency Bandwidth ◽  
Frequency Range ◽  
High Isolation ◽  
Small Rectangle ◽  
Additional Resonance ◽  
Dual Polarized ◽  
Better Than

A wideband dual-polarized multidipole antenna for base station applications is proposed. It consists of a pair of large square-shaped loop dipoles and a pair of small rectangle loop dipoles as radiation elements. A pair of small rectangle loop dipoles is fed by T-shaped feed structure which is in the large square-shaped loop dipoles radiating arm so that the antenna generates an additional resonance and obtains a wider bandwidth. The proposed antenna was fabricated and measured, and the results show that the antenna achieves a wide impedance bandwidth of 63.7 % with VSWR<1.5 covering the frequency range from 1.55 to 3 GHz. A high isolation is better than 29 dB within the operating frequency bandwidth. Moreover, an average gain 8 dBi and a stable radiation pattern with 3 dB beamwidth of 69° ± 4° at H-plane are obtained.

Sign in / Sign up

Export Citation Format

Share Document