scholarly journals PVT and ETC Coupling for Annual Heating and Cooling by Absorption Heat Pumps

2020 ◽  
Vol 12 (17) ◽  
pp. 7042
Author(s):  
Marco Noro ◽  
Renato Lazzarin
Keyword(s):  
Heat Pump ◽  
Cell Damage ◽  
Primary Energy ◽  
Heat Pumps ◽  
Solar Thermal ◽  
Solar Collectors ◽  
Absorption Chiller ◽  
Heating And Cooling ◽  
Cold Source ◽  
Temperature Levels

Until recently, solar assisted heat pumps have used solar collectors as a cold source. Solar collectors provide, when possible, direct heat, otherwise they offer temperature levels to the heat pump evaporator higher than the outside air. At the same time, solar thermal cooling exploits the solar collectors and the absorption chiller only in hot months. Photovoltaic/Thermal (PVT) modules have been available on the market in recent years for solar cogeneration, but their utilization can be problematic due to PhotoVoltaic (PV) cell damage in cases where there is no heating request. This paper considers the possibility of coupling evacuated tube collectors and photovoltaic/thermal modules to drive an absorption heat pump-based plant operating as an absorption chiller in the summertime. The cold source is the solar energy and the ground, which is recharged by the solar thermal and photovoltaic/thermal collectors and by the cooling of the absorber-condenser in mid-seasons and summer. This study analyzes the system behavior in yearly operation and evaluates the role of suitable storage tanks in two different climates, varying the size of the two solar fields and the generator tank. In the best plant configuration, a primary energy ratio of 26.6 in colder climates with cloudy skies and 20 in hotter climates with clearer skies is obtained.

scholarly journals Heat pump systems: A mini review

2021 ◽  
Vol 4 (2) ◽  
pp. 73-81
Author(s):  
Mohammad Omar Temori ◽  
František Vranay
Keyword(s):  
Heat Pump ◽  
Electricity Consumption ◽  
Cost Savings ◽  
Electrical Energy ◽  
Primary Energy ◽  
Heat Pumps ◽  
Coefficient Of Performance ◽  
Heating And Cooling ◽  
Ground Source ◽  
Reduce Electricity Consumption

In this work, a mini review of heat pumps is presented. The work is intended to introduce a technology that can be used to income energy from the natural environment and thus reduce electricity consumption for heating and cooling. A heat pump is a mechanical device that transfers heat from one environmental compartment to another, typically against a temperature gradient (i.e. from cool to hot). In order to do this, an energy input is required: this may be mechanical, electrical or thermal energy. In most modern heat pumps, electrical energy powers a compressor, which drives a compression - expansion cycle of refrigerant fluid between two heat exchanges: a cold evaporator and a warm condenser. The efficiency or coefficient of performance (COP), of a heat pump is defined as the thermal output divided by the primary energy (electricity) input. The COP decreases as the temperature difference between the cool heat source and the warm heat sink increases. An efficient ground source heat pump (GSHP) may achieve a COP of around 4. Heat pumps are ideal for exploiting low-temperature environmental heat sources: the air, surface waters or the ground. They can deliver significant environmental (CO2) and cost savings.

Solar Thermal Driven Cooling System for a Data Center in Albuquerque New Mexico

2010 ◽  
Author(s):  
N. Fumo ◽  
V. Bortone ◽  
J. C. Zambrano
Keyword(s):  
Energy Consumption ◽  
Data Center ◽  
Data Centers ◽  
Primary Energy ◽  
Continuous Operation ◽  
Solar Thermal ◽  
Primary Energy Consumption ◽  
Solar Collectors ◽  
Absorption Chiller ◽  
Solar Cooling

Data centers are facilities that primarily contain electronic equipment used for data processing, data storage, and communications networking. Regardless of their use and configuration, most data centers are more energy intensive than other buildings. The continuous operation of Information Technology equipment and power delivery systems generates a significant amount of heat that must be removed from the data center for the electronic equipment to operate properly. Since data centers spend up to half their energy on cooling, cooling systems becomes a key factor for energy consumption reduction strategies and alternatives in data centers. This paper presents a theoretical analysis of an absorption chiller driven by solar thermal energy as cooling plant alternative for data centers. Source primary energy consumption is used to compare the performance of different solar cooling plants with a standard cooling plant. The solar cooling plants correspond to different combinations of solar collector arrays and thermal storage tank, with a boiler as source of energy to ensure continuous operation of the absorption chiller. The standard cooling plant uses an electric chiller. Results suggest that the solar cooling plant with flat-plate solar collectors is a better option over the solar cooling plant with evacuated-tube solar collectors. However, although solar cooling plants can decrease the primary energy consumption when compared with the standard cooling plant, the net present value of the cost to install and operate the solar cooling plants are higher than the one for the standard cooling plant.

Solar Thermal Driven Cooling System for a Data Center in Albuquerque New Mexico

2011 ◽  
Vol 133 (4) ◽  
Author(s):  
N. Fumo ◽  
V. Bortone ◽  
J. C. Zambrano
Keyword(s):  
Energy Consumption ◽  
Data Center ◽  
Data Centers ◽  
Primary Energy ◽  
Continuous Operation ◽  
Solar Thermal ◽  
Primary Energy Consumption ◽  
Solar Collectors ◽  
Absorption Chiller ◽  
Solar Cooling

Data centers are facilities that primarily contain electronic equipment used for data processing, data storage, and communications networking. Regardless of their use and configuration, most data centers are more energy intensive than other buildings. The continuous operation of information technology equipment and power delivery systems generates a significant amount of heat that must be removed from the data center for the electronic equipment to operate properly. Since data centers spend up to half their energy on cooling, cooling systems becomes a key factor for energy consumption reduction strategies and alternatives in the data centers. This paper presents a theoretical analysis of an absorption chiller driven by solar thermal energy as cooling plant alternative for data centers. Source primary energy consumption is used to compare the performance of different solar cooling plants with a standard cooling plant. The solar cooling plants correspond to different combinations of solar collector arrays and thermal storage tank, with a boiler as source of energy to ensure continuous operation of the absorption chiller. The standard cooling plant uses an electric chiller. Results suggest that the solar cooling plant with flat-plate solar collectors is a better option over the solar cooling plant with evacuated-tube solar collectors. However, although solar cooling plants can decrease the primary energy consumption when compared with the standard cooling plant, the net present value of the cost to install and operate the solar cooling plants are higher than the one for the standard cooling plant.

Modeling and Experimental Investigation of an Oil-Free Micro Compressor-Turbine Unit for an ORC Driven Heat Pump

2014 ◽  
Author(s):  
Jonathan Demierre ◽  
Antonio Rubino ◽  
Jürg Schiffmann
Keyword(s):  
Heat Pump ◽  
Turbine Unit ◽  
Organic Rankine Cycle ◽  
Primary Energy ◽  
Heat Pumps ◽  
Tip Clearance ◽  
Heating And Cooling ◽  
Compression Cycle ◽  
Thermally Driven ◽  
Vapour Compression

Domestic heating and cooling will more and more have to rely on heat pumps in order to support a more rational use of primary energy consumption. The heat pump market is mainly dominated by electrically driven vapour compression cycles and by thermally driven sorption processes. The drawback of electrically driven vapour compression cycle is their dependence on an electrical grid and the fact that they increase the winter or summer electricity peak demands. Hence, a thermally driven vapour compression cycle would offer substantial advantages and flexibility to the end user for heating and cooling applications. This paper presents the investigation of an oil-free Compressor-Turbine Unit (CTU) used for a Thermally Driven Heat Pump (TDHP) based on the combination of a heat pump compression cycle and an Organic Rankine Cycle (ORC). The CTU consists of a radial inflow turbine and a centrifugal compressor of the order of 2 kW each, directly coupled through a shaft supported on gas lubricated bearings. The CTU has been tested at rotor speeds in excess of 200 krpm, reaching compressor and turbine pressure ratios up to 2.8 and 4.4 respectively and isentropic efficiencies around 70%. Comparisons between the experimental data and predictions of models, that are briefly described here, have been carried out. A sensitivity analysis based on the experimentally validated models shows that tip clearance, for both compressor and turbine, and surface roughness of the compressor are key parameters for further improving performance.

Saving Primary Energy Consumption Through Exergy Analysis of Combine Distillation and Power Plant

2012 ◽  
Vol 9 (2) ◽  
pp. 65
Author(s):  
Alhassan Salami Tijani ◽  
Nazri Mohammed ◽  
Werner Witt
Keyword(s):  
Energy Consumption ◽  
Power Plant ◽  
Heat Pump ◽  
Heat Recovery ◽  
Energy Savings ◽  
Primary Energy ◽  
Heat Pumps ◽  
Saturated Steam ◽  
Distillation Unit ◽  
Primary Energy Consumption

Industrial heat pumps are heat-recovery systems that allow the temperature ofwaste-heat stream to be increased to a higher, more efficient temperature. Consequently, heat pumps can improve energy efficiency in industrial processes as well as energy savings when conventional passive-heat recovery is not possible. In this paper, possible ways of saving energy in the chemical industry are considered, the objective is to reduce the primary energy (such as coal) consumption of power plant. Particularly the thermodynamic analyses ofintegrating backpressure turbine ofa power plant with distillation units have been considered. Some practical examples such as conventional distillation unit and heat pump are used as a means of reducing primary energy consumption with tangible indications of energy savings. The heat pump distillation is operated via electrical power from the power plant. The exergy efficiency ofthe primary fuel is calculated for different operating range ofthe heat pump distillation. This is then compared with a conventional distillation unit that depends on saturated steam from a power plant as the source of energy. The results obtained show that heat pump distillation is an economic way to save energy if the temperaturedifference between the overhead and the bottom is small. Based on the result, the energy saved by the application of a heat pump distillation is improved compared to conventional distillation unit.

scholarly journals Renewable Heating and Cooling Solutions for Buildings and Industry

Proceedings ◽  
2020 ◽  
Vol 65 (1) ◽  
pp. 16
Author(s):  
Andrea Frazzica ◽  
Régis Decorme ◽  
Marco Calderoni ◽  
Alessandra Cuneo ◽  
Zuzana Taťáková ◽  
...  
Keyword(s):  
Renewable Energy ◽  
Heat Pump ◽  
Solar Thermal ◽  
Renewable Energy Technologies ◽  
Energy Technologies ◽  
Heating And Cooling ◽  
Common Strategy ◽  
Selection Of

This workshop brought together a selection of H2020 EU-funded projects involving experts from the biomass, geothermal, solar thermal, and heat pump sectors to discuss a common strategy for increasing the use of renewable energy technologies for heating and cooling for buildings and industry.

Combined Solar Heating and Cooling Systems: Simulation and Design Optimization

2008 ◽  
Author(s):  
Giovanni Nurzia ◽  
Giuseppe Franchini ◽  
Antonio Perdichizzi
Keyword(s):  
Design Optimization ◽  
Heat Pump ◽  
Solar Heating ◽  
Solar Irradiation ◽  
Space Heating ◽  
Thermal Source ◽  
Absorption Chiller ◽  
Cooling Systems ◽  
Detailed Model ◽  
Heating And Cooling

The deployment of solar driven air conditioning is a feasible target in all countries where high solar irradiation matches high cooling loads in buildings: the goal is to gradually replace compression chillers and reduce peak electricity demand during summer. Moreover, as solar thermal collectors are installed, solar cooling systems can be profitably employed during winter. In the present work a code has been implemented for the simulation and the design optimization of combined solar heating and cooling systems. The following system layout has been considered: in warm months the cooling demand is satisfied by means of an absorption chiller — driven by a solar collector field — and a reversible heat pump operating in series. A hot storage matches the variability of solar radiation, while a cold storage smoothes the non-stationarity of cooling demand. During winter, the reversible compression heat pump operates for space heating. Solar collectors are used as thermal source at the evaporator of the heat pump, increasing its coefficient of performance. The code, based on TRNSYS platform, is able to simulate the system throughout a year. Besides TRNSYS standard components a detailed model of the absorption chiller has been included, in order to accurately simulate its off-design operation. Using an optimization tool the size of each component is identified for a given space heating and cooling demand. The minimization of life cycle costs of the system has been chosen as the objective of the optimization. Results of a case study are presented and discussed for a solar heating and cooling plant in an office building. The optimization procedure has been carried out with simulations for a typical Northern Italy town (Alpine climate) and a typical Southern Italy town (Mediterranean climate).

scholarly journals A GIS-Based Planning Approach for Urban Power and Natural Gas Distribution Grids with Different Heat Pump Scenarios

Energies ◽  
2020 ◽  
Vol 13 (16) ◽  
pp. 4052 ◽  
Author(s):  
Jolando M. Kisse ◽  
Martin Braun ◽  
Simon Letzgus ◽  
Tanja M. Kneiske
Keyword(s):  
Co2 Emissions ◽  
Heat Pump ◽  
Energy Demand ◽  
Low Voltage ◽  
Primary Energy ◽  
Heat Pumps ◽  
Slight Reduction ◽  
Single Family ◽  
Gas Distribution ◽  
Public Data

Next to building insulation, heat pumps driven by electrical compressors (eHPs) or by gas engines (geHPs) can be used to reduce primary energy demand for heating. They come with different investment requirements, operating costs and emissions caused. In addition, they affect both the power and gas grids, which necessitates the assessment of both infrastructures regarding grid expansion planning. To calculate costs and CO2 emissions, 2000 electrical load profiles and 180 different heat demand profiles for single-family homes were simulated and heat pump models were applied. In a case study for a neighborhood energy model, the load profiles were assigned to buildings in an example town using public data on locations, building age and energetic refurbishment variants. In addition, the town’s gas distribution network and low voltage grid were modeled. Power and gas flows were simulated and costs for required grid extensions were calculated for 11% and 16% heat pump penetration. It was found that eHPs have the highest energy costs but will also have the lowest CO2 emissions by 2030 and 2050. For the investigated case, power grid investments of 11,800 euros/year are relatively low compared to gas grid connection costs of 70,400 euros/year. If eHPs and geHPs are combined, a slight reduction of overall costs is possible, but emissions would rise strongly compared to the all-electric case.

scholarly journals A European Database of Building Energy Profiles to Support the Design of Ground Source Heat Pumps

Energies ◽  
2019 ◽  
Vol 12 (13) ◽  
pp. 2496 ◽  
Author(s):  
Laura Carnieletto ◽  
Borja Badenes ◽  
Marco Belliardi ◽  
Adriana Bernardi ◽  
Samantha Graci ◽  
...  
Keyword(s):  
Heat Pump ◽  
Energy Demand ◽  
Residential Buildings ◽  
Building Energy ◽  
Heat Pumps ◽  
Climatic Conditions ◽  
Ground Source Heat Pumps ◽  
Heating And Cooling ◽  
Energy Profiles ◽  
Ground Source

The design of ground source heat pumps is a fundamental step to ensure the high energy efficiency of heat pump systems throughout their operating years. To enhance the diffusion of ground source heat pump systems, two different tools are developed in the H2020 research project named, “Cheap GSHPs”: A design tool and a decision support system. In both cases, the energy demand of the buildings may not be calculated by the user. The main input data, to evaluate the size of the borehole heat exchangers, is the building energy demand. This paper presents a methodology to correlate energy demand, building typologies, and climatic conditions for different types of residential buildings. Rather than envelope properties, three insulation levels have been considered in different climatic conditions to set up a database of energy profiles. Analyzing European climatic test reference years, 23 locations have been considered. For each location, the overall energy and the mean hourly monthly energy profiles for heating and cooling have been calculated. Pre-calculated profiles are needed to size generation systems and, in particular, ground source heat pumps. For this reason, correlations based on the degree days for heating and cooling demand have been found in order to generalize the results for different buildings. These correlations depend on the Köppen–Geiger climate scale.

Solar-Assisted Heat Pump Systems: A Review of Existing Studies and Their Applicability to the Canadian Residential Sector

2013 ◽  
Author(s):  
Jenny Chu ◽  
Cynthia A. Cruickshank
Keyword(s):  
Heat Pump ◽  
Residential Buildings ◽  
International Energy Agency ◽  
Heat Pumps ◽  
Hot Water ◽  
Performance Criteria ◽  
Space Heating ◽  
Residential Sector ◽  
Heating And Cooling ◽  
System Configurations

Heat pumps are commonly used for space-heating and cooling requirements. The combination of solar thermal and heat pump systems as a single solar-assisted heat pump (SAHP) system is a promising technology for offsetting domestic hot water, space-heating and cooling loads more efficiently. Task 44 of the Solar Heating and Cooling Programme of the International Energy Agency is currently investigating ways to optimize SAHP systems for residential use. This paper presents a review of past and current work conducted on SAHP systems. Specifically, the key performance data from many studies are highlighted and different system configurations are compared in order to establish insight towards which system configurations are suitable for the Canadian residential sector. It was found that the most suitable configuration for Canadian residential buildings depend on a combination of factors which may include occupant behavior, building characteristics, operation parameters, system components, the performance criteria of interest and climate. A large variety of configurations and parameters exist for SAHP systems and this made analyzing a specific system, comparing differing systems and establishing an optimal design fairly difficult. It was found that different authors used various different performance criterions and this inconsistency also added to the difficulty of comparing the studies of different systems. Overall, a standard performance criterion needs to be established for SAHP systems in order to meaningfully compare different configurations and determine optimal configurations for certain requirements.

Sign in / Sign up

Export Citation Format

Share Document