scholarly journals Research on Static and Dynamic Characteristics of Shear Spring of the Vibrating Flip-Flow Screen

Symmetry ◽  
2020 ◽  
Vol 12 (10) ◽  
pp. 1644
Author(s):  
Guofeng Zhao ◽  
Xinwen Wang ◽  
Chi Yu ◽  
Shucheng Liu ◽  
Jun Zhou ◽  
...  
Keyword(s):  
Dynamic Characteristics ◽  
High Efficiency ◽  
Dynamic Stiffness ◽  
Test System ◽  
Normal Operation ◽  
Static And Dynamic Characteristics ◽  
Damping Coefficients ◽  
Operation Conditions ◽  
Shear Spring ◽  
Stiffness And Damping

The vibrating flip-flow screen (VFFS) is a high-efficiency device currently used for deep screening of moist fine-grained materials. During VFFS operation, the normal operation of the screen is affected by fatigue damage to the shear springs arranged symmetrically on both sides of the screen, leading to equipment failures and disruption production. In this paper, the shear spring’s static and dynamic characteristics in different operation conditions were studied using the INSTRON 8801 fatigue test system and Dynacell dynamic sensors. Using an experimental test of shear spring stiffness and damping coefficients, the effects of some factors, i.e., temperature, hardness, amplitude and frequency, were studied. The results show that the temperature of the shear spring on the left side of the flip-flow screen was higher than that of the right side (driving side). With an increase in temperature, the stiffness of the shear spring decreased. With the increase in amplitude, the dynamic stiffness decreased and the damping coefficients did not change; with the increase in frequency, the dynamic stiffness increased and the damping coefficient decreased. At the same amplitude, with the increase in hardness of the shear spring, the dynamic stiffness increased. Finally, the stiffness and damping coefficients of the shear spring before and after tearing were obviously reduced. These research results reveal the relationship of the characteristics of a shear spring with operational conditions, and could provide a theoretical reference for the design of the VFFS and the selection of the shear spring.

Dynamic Characteristics of Hydrostatic Thrust Air Bearing With Actively Controlled Restrictor

1988 ◽  
Vol 110 (1) ◽  
pp. 156-161 ◽  
Author(s):  
Yuichi Sato ◽  
K. Maruta ◽  
M. Harada
Keyword(s):  
Dynamic Characteristics ◽  
Dynamic Stiffness ◽  
Phase Lag ◽  
Air Bearing ◽  
Plate Vibrations ◽  
Damping Coefficients ◽  
Stiffness And Damping ◽  
Air Film ◽  
Theoretical Results ◽  
Good Agreement

The dynamic characteristics of a hydrostatic thrust air bearing with an actively controlled orifice restrictor are investigated theoretically and experimentally. Theoretical results show that the dynamic stiffness and damping coefficients can be increased simultaneously when the restrictor area is controlled with appropriate phase-lag to the change of air film thickness, that is, plate vibrations. Consequently stability of the bearing can be improved. Experimental results show fairly good agreement with theoretical ones.

Static and dynamic characteristics and stability analysis of high-speed water-lubricated hydrodynamic journal bearings

2021 ◽  
pp. 135065012110270
Author(s):  
Bo Xu ◽  
Hun Guo ◽  
Xiaofeng Wu ◽  
Yafeng He ◽  
Xiangzhi Wang ◽  
...  
Keyword(s):  
Stability Analysis ◽  
Dynamic Characteristics ◽  
High Speed ◽  
Load Capacity ◽  
Journal Bearings ◽  
Operating Conditions ◽  
Inertia Effect ◽  
Static And Dynamic Characteristics ◽  
Damping Coefficients ◽  
Stiffness And Damping

The purpose of this paper is to analyze the influence of turbulent, inertia, and misaligned effects on the static and dynamic characteristics and stability of high-speed water-lubricated hydrodynamic journal bearings. Based on the Navier–Stokes equation, the mixing-length theory, and the essential assumption that the velocity profile is not strongly affected by inertia force, the fluid lubrication model with turbulent, inertia, and misaligned effects is established, and then the stability analysis of bearings is carried out based on the equation of motion with four degrees of freedom. The model is solved by the finite difference method and the numerical results are compared under different operating conditions. The results show that the turbulent effect greatly increases the load capacity, power consumption, stiffness and damping coefficients, and stability of bearings, and the inertia effect significantly increases the volume flow rate of bearings, and the misaligned effect increases the load capacity, stiffness and damping coefficients, and stability of bearings. In high rotary speed and moderate eccentricity ratios, the influence of the inertia effect on the load capacity, stiffness coefficients, and stability cannot be neglected.

Design and structural performance measurements of a novel multi-cantilever foil bearing

2014 ◽  
Vol 229 (10) ◽  
pp. 1830-1838 ◽  
Author(s):  
Kai Feng ◽  
Xueyuan Zhao ◽  
Zhiyang Guo
Keyword(s):  
Dynamic Characteristics ◽  
Dynamic Load ◽  
Dynamic Stiffness ◽  
Excitation Frequency ◽  
Viscous Damping ◽  
Equivalent Viscous Damping ◽  
Foil Bearing ◽  
Load Tests ◽  
Stiffness And Damping ◽  
Motion Amplitude

With increasing need for high-speed, high-temperature, and oil-free turbomachinery, gas foil bearings (GFBs) have been considered to be the best substitutes for traditional oil-lubricated bearings. A multi-cantilever foil bearing (MCFB), a novel GFB with multi-cantilever foil strips serving as the compliant underlying structure, was designed, fabricated, and tested. A series of static and dynamic load tests were conducted to measure the structural stiffness and equivalent viscous damping of the prototype MCFB. Experiments of static load versus deflection showed that the proposed bearing has a large mechanical energy dissipation capability and a pronounced nonlinear static stiffness that can prevents overly large motion amplitude of journal. Dynamic load tests evaluated the influence of motion amplitude, loading orientation and misalignment on the dynamic stiffness and equivalent viscous damping with respect to excitation frequency. The test results demonstrated that the dynamic stiffness and damping are strongly dependent on the excitation frequency. Three motion amplitudes were applied to the bearing housing to investigate the effects of motion amplitude on the dynamic characteristics. It is noted that the bearing dynamic stiffness and damping decreases with incrementally increasing motion amplitudes. A high level of misalignment can lead to larger static and dynamic bearing stiffness as well as to larger equivalent viscous damping. With dynamic loads applied to two orientations in the bearing midplane separately, the dynamic stiffness increases rapidly and the equivalent viscous damping declines slightly. These results indicate that the loading orientation is a non-negligible factor on the dynamic characteristics of MCFBs.

Calculation and Measurement of the Stiffness and Damping Coefficients for a Low Impedance Hydrodynamic Bearing

1997 ◽  
Vol 119 (1) ◽  
pp. 57-63 ◽  
Author(s):  
M. J. Goodwin ◽  
P. J. Ogrodnik ◽  
M. P. Roach ◽  
Y. Fang
Keyword(s):  
Experimental Data ◽  
Dynamic Stiffness ◽  
Perturbation Technique ◽  
The Novel ◽  
Oil Film ◽  
Hydrodynamic Bearing ◽  
Damping Coefficients ◽  
Stiffness And Damping ◽  
Film Stiffness ◽  
Novel Design

This paper describes a combined theoretical and experimental investigation of the eight oil film stiffness and damping coefficients for a novel low impedance hydrodynamic bearing. The novel design incorporates a recess in the bearing surface which is connected to a standard commercial gas bag accumulator; this arrangement reduces the oil film dynamic stiffness and leads to improved machine response and stability. A finite difference method was used to solve Reynolds equation and yield the pressure distribution in the bearing oil film. Integration of the pressure profile then enabled the fluid film forces to be evaluated. A perturbation technique was used to determine the dynamic pressure components, and hence to determine the eight oil film stiffness and damping coefficients. Experimental data was obtained from a laboratory test rig in which a test bearing, floating on a rotating shaft, was excited by a multi-frequency force signal. Measurements of the resulting relative movement between bearing and journal enabled the oil film coefficients to be measured. The results of the work show good agreement between theoretical and experimental data, and indicate that the oil film impedance of the novel design is considerably lower than that of a conventional bearing.

The Surface Roughness Effect on the Dynamic Stiffness and Damping Characteristics of the Hydrostatic Thrust Spherical Bearings: Part 5 of 5 — Clearance Type of Bearings

2007 ◽  
Author(s):  
Ahmad W. Yacout
Keyword(s):  
Surface Roughness ◽  
Capillary Tube ◽  
Dynamic Stiffness ◽  
Dynamic Performance ◽  
Major Effect ◽  
Design Parameters ◽  
Compressibility Effect ◽  
Damping Coefficients ◽  
Stiffness And Damping ◽  
Fluid Compressibility

This study has theoretically analyzed the surface roughness, centripetal inertia and recess volume fluid compressibility effects on the dynamic behavior of a restrictor compensated hydrostatic thrust spherical clearance type of bearing. The stochastic Reynolds equation, with centripetal inertia effect, and the recess flow continuity equation with recess volume fluid compressibility effect have been derived to take into account the presence of roughness on the bearing surfaces. On the basis of a small perturbations method, the dynamic stiffness and damping coefficients have been evaluated. In addition to the usual bearing design parameters the results for the dynamic stiffness and damping coefficients have been calculated for various frequencies of vibrations or squeeze parameter (frequency parameter) and recess volume fluid compressibility parameter. The study shows that both of the surface roughness and the centripetal inertia have slight effects on the stiffness coefficient and remarkable effects on the damping coefficient while the recess volume fluid compressibility parameter has the major effect on the bearing dynamic characteristics. The cross dynamic stiffness showed the bearing self-aligning property and the ability to oppose whirl movements. The orifice restrictor showed better dynamic performance than that of the capillary tube.

Dynamic Characteristics of Spiral-Grooved Opposed-Hemisphere Gas Bearings

2016 ◽  
Vol 139 (3) ◽  
Author(s):  
Guangwei Yang ◽  
Jianjun Du ◽  
Weiping Ge ◽  
Tun Liu ◽  
Xiaowei Yang
Keyword(s):  
Dynamic Characteristics ◽  
Degrees Of Freedom ◽  
Dynamic Stiffness ◽  
Translational Motion ◽  
Coupling Coefficients ◽  
Dynamic Coefficients ◽  
Large Eccentricity ◽  
The Stability ◽  
Stiffness And Damping ◽  
Gas Bearing

The traditional eight-coefficient bearing model only considers the translational motion of the bearings and neglects the tilting motion and coupling effects between them. In this paper, the dynamic characteristics of the spiral-grooved opposed-hemisphere gas bearing considering five degrees-of-freedom are studied, and 50 dynamic coefficients including the translational, tilting, and coupling components are completely calculated. The Reynolds equations and their perturbed equations are solved by the finite element method to obtain the dynamic stiffness and damping coefficients. The effects of the tilting motion on the dynamic coefficients and response are analyzed, respectively. The results show that the coupling coefficients between the translational and tilting motions, which have been neglected in most previous studies, are significant at large eccentricity ratio. But these coupling coefficients have little effect on the dynamic response. On the other hand, the influences of the tilting motion on the synchronous response and natural frequency are remarkable and will decrease the stability of the rotor bearing system.

Stiffness and Damping Characteristics of a Wide Parabolic Film Slider Bearing Operating with Ferrofluids

2014 ◽  
Vol 1052 ◽  
pp. 132-136
Author(s):  
Jaw Ren Lin
Keyword(s):  
Magnetic Fields ◽  
Dynamic Characteristics ◽  
Dynamic Stiffness ◽  
Slider Bearing ◽  
Inclined Plane ◽  
Damping Characteristics ◽  
Plane Film ◽  
Stiffness And Damping

This paper investigates the dynamic characteristics of parabolic film slider bearing operating with ferrofluids. Comparing with the slider bearing of an inclined plane film, the parabolic film slider bearing operating with ferrofluids in the presence of external magnetic fields provide higher better dynamic stiffness and damping performances.

An Experimental Investigation on the Static and Dynamic Characteristics of Journal Bearings Under the Influence of Twisting Misalignment

1997 ◽  
Vol 119 (1) ◽  
pp. 188-192 ◽  
Author(s):  
P. Arumugam ◽  
S. Swarnamani ◽  
B. S. Prabhu
Keyword(s):  
Finite Element Method ◽  
Vertical Direction ◽  
Journal Bearings ◽  
Response Functions ◽  
The Finite Element Method ◽  
Static And Dynamic Characteristics ◽  
Damping Coefficients ◽  
Stiffness And Damping ◽  
Different Levels ◽  
Bearing System

The misalignment between the journal and the bearing in a rotor-bearing system may be due to manufacturing error, elastic deflection, thermal expansion etc. In the present work, the eight linearized stiffness and damping coefficients of the cylindrical and three lobe bearings are identified at different levels of bearing misalignment (twisting misalignment) and at different speeds of the rotor. The identification method used here needs FRFs (Frequency Response Functions) obtained by the measurements and the finite element method. The twisting misalignment changes the stiffness and damping coefficients in the vertical and horizontal directions. In the case of three lobe bearings, for 0.7 degree of misalignment, the stiffness in the vertical direction is increased by about 12 percent.

Numerical Analysis on Dynamic Characteristics of Cryogenic Hydrostatic Journal Bearing

1999 ◽  
Vol 121 (4) ◽  
pp. 879-885 ◽  
Author(s):  
Hiroyuki Yoshikawa ◽  
Terukazu Ota ◽  
Kazuyuki Higashino ◽  
Shunichiro Nakai
Keyword(s):  
Numerical Analysis ◽  
Dynamic Characteristics ◽  
Rotational Speed ◽  
Frequency Ratio ◽  
Journal Bearing ◽  
Liquid Hydrogen ◽  
Transport Systems ◽  
Rocket Engines ◽  
Damping Coefficients ◽  
Stiffness And Damping

Dynamic characteristics of a two row staggered recess cryogenic hydrostatic journal bearing used in the liquid hydrogen turbopump of rocket engines for space transport systems are numerically analyzed. Effects of the rotational speed and the shaft eccentricity are studied in the analysis. Their effects on the stiffness and damping coefficients and the whirl frequency ratio are clarified. Moreover, effects of the orifice parameter, the distance between two recess rows, and the number of recesses on these dynamic characteristics are investigated.

Sign in / Sign up

Export Citation Format

Share Document