Variations of the Snow Water Equivalent in the Ourika Catchment (Morocco) over 2000–2018 Using Downscaled MERRA-2 Data

The Ourika River is an important tributary of the Tensift River in the water-stressed region of Marrakesh (Morocco). The Ourika river flow is dominated by the snow melt contribution from the High Atlas mountains. Despite its importance in terms of water resources, the snow water equivalent (SWE) is poorly monitored in the Ourika catchment. Here, we used MERRA-2 data to run a distributed energy-balance snowpack model (SnowModel) over 2000–2018. MERRA-2 data were downscaled to 250-m spatial resolution using a digital elevation model. The model outputs were compared to in situ measurements of snow depth, precipitation, river flow and remote sensing observations of the snow cover area from MODIS. The results indicate that the model provides an overall acceptable representation of the snow cover dynamics given the coarse resolution of the MERRA-2 forcing. Then, we used the model output to analyze the spatio-temporal variations of the SWE in the Ourika catchment for the first time. We suggest that MERRA-2 data, which are routinely available with a delay of a few weeks, can provide valuable information to monitor the snow resource in high mountain areas without in situ measurements.

Download Full-text

Assimilation of snow cover and snow depth into a snow model to estimate snow water equivalent and snowmelt runoff in a Himalayan catchment

The Cryosphere ◽

10.5194/tc-11-1647-2017 ◽

2017 ◽

Vol 11 (4) ◽

pp. 1647-1664 ◽

Cited By ~ 29

Author(s):

Emmy E. Stigter ◽

Niko Wanders ◽

Tuomo M. Saloranta ◽

Joseph M. Shea ◽

Marc F. P. Bierkens ◽

...

Keyword(s):

Kalman Filter ◽

Data Assimilation ◽

Snow Cover ◽

Climate Sensitivity ◽

Snow Depth ◽

Snow Water Equivalent ◽

Snowmelt Runoff ◽

Snow Water ◽

Snow Model

Abstract. Snow is an important component of water storage in the Himalayas. Previous snowmelt studies in the Himalayas have predominantly relied on remotely sensed snow cover. However, snow cover data provide no direct information on the actual amount of water stored in a snowpack, i.e., the snow water equivalent (SWE). Therefore, in this study remotely sensed snow cover was combined with in situ observations and a modified version of the seNorge snow model to estimate (climate sensitivity of) SWE and snowmelt runoff in the Langtang catchment in Nepal. Snow cover data from Landsat 8 and the MOD10A2 snow cover product were validated with in situ snow cover observations provided by surface temperature and snow depth measurements resulting in classification accuracies of 85.7 and 83.1 % respectively. Optimal model parameter values were obtained through data assimilation of MOD10A2 snow maps and snow depth measurements using an ensemble Kalman filter (EnKF). Independent validations of simulated snow depth and snow cover with observations show improvement after data assimilation compared to simulations without data assimilation. The approach of modeling snow depth in a Kalman filter framework allows for data-constrained estimation of snow depth rather than snow cover alone, and this has great potential for future studies in complex terrain, especially in the Himalayas. Climate sensitivity tests with the optimized snow model revealed that snowmelt runoff increases in winter and the early melt season (December to May) and decreases during the late melt season (June to September) as a result of the earlier onset of snowmelt due to increasing temperature. At high elevation a decrease in SWE due to higher air temperature is (partly) compensated by an increase in precipitation, which emphasizes the need for accurate predictions on the changes in the spatial distribution of precipitation along with changes in temperature.

Download Full-text

Validation of modeled snow properties in Afghanistan, Pakistan, and Tajikistan

10.5194/tc-2019-150 ◽

2019 ◽

Author(s):

Edward H. Bair ◽

Karl Rittger ◽

Jawairia A. Ahmad ◽

Doug Chabot

Keyword(s):

Snow Depth ◽

Snow Water Equivalent ◽

Median Number ◽

In Situ Measurements ◽

Snow Properties ◽

Wide Range ◽

Spatial Estimates ◽

Snow Water ◽

Critical Layers

Abstract. Ice and snowmelt feed the Indus and Amu Darya rivers, yet there are limited in situ measurements of these resources. Previous work in the region has shown promise using snow water equivalent (SWE) reconstruction, which requires no in situ measurements, but validation has been a problem until recently when we were provided with daily manual snow depth measurements from Afghanistan, Tajikistan, and Pakistan by the Aga Khan Agency for Habitat (AKAH). For each station, accumulated precipitation and SWE were derived from snow depth using the SNOWPACK model. High-resolution (500 m) reconstructed SWE estimates from the ParBal model were then compared to the modeled SWE at the stations. The Alpine3D model was then used to create spatial estimates at 25 km to compare with estimates from other snow models. Additionally, the coupled SNOWPACK and Alpine3D system has the advantage of simulating snow profiles, which provide stability information. Following previous work, the median number of critical layers and percentage of facets across all of the pixels containing the AKAH stations was computed. For SWE at the point scale, the reconstructed estimates showed a bias of −42 mm (−19 %) at the peak. For the coarser spatial SWE estimates, the various models showed a wide range, with reconstruction being on the lower end. For stratigraphy, a heavily faceted snowpack is observed in both years, but 2018, a dry year, according to most of the models, showed more critical layers that persisted for a longer period.

Download Full-text

Using Air Temperature to Quantitatively Predict the MODIS Fractional Snow Cover Retrieval Errors over the Continental United States

Journal of Hydrometeorology ◽

10.1175/jhm-d-13-060.1 ◽

2014 ◽

Vol 15 (2) ◽

pp. 551-562 ◽

Cited By ~ 7

Author(s):

Jiarui Dong ◽

Mike Ek ◽

Dorothy Hall ◽

Christa Peters-Lidard ◽

Brian Cosgrove ◽

...

Keyword(s):

United States ◽

Snow Cover ◽

Air Temperature ◽

Snow Water Equivalent ◽

Probability Of Detection ◽

Joint Analysis ◽

Snow Cover Area ◽

Fractional Snow Cover ◽

Retrieval Errors

Abstract Understanding and quantifying satellite-based, remotely sensed snow cover uncertainty are critical for its successful utilization. The Moderate Resolution Imaging Spectroradiometer (MODIS) snow cover errors have been previously recognized to be associated with factors such as cloud contamination, snowpack grain sizes, vegetation cover, and topography; however, the quantitative relationship between the retrieval errors and these factors remains elusive. Joint analysis of the MODIS fractional snow cover (FSC) from Collection 6 (C6) and in situ air temperature and snow water equivalent measurements provides a unique look at the error structure of the MODIS C6 FSC products. Analysis of the MODIS FSC dataset over the period from 2000 to 2005 was undertaken over the continental United States (CONUS) with an extensive observational network. When compared to MODIS Collection 5 (C5) snow cover area, the MODIS C6 FSC product demonstrates a substantial improvement in detecting the presence of snow cover in Nevada [30% increase in probability of detection (POD)], especially in the early and late snow seasons; some improvement over California (10% POD increase); and a relatively small improvement over Colorado (2% POD increase). However, significant spatial and temporal variations in accuracy still exist, and a proxy is required to adequately predict the expected errors in MODIS C6 FSC retrievals. A relationship is demonstrated between the MODIS FSC retrieval errors and temperature over the CONUS domain, captured by a cumulative double exponential distribution function. This relationship is shown to hold for both in situ and modeled daily mean air temperature. Both of them are useful indices in filtering out the misclassification of MODIS snow cover pixels and in quantifying the errors in the MODIS C6 product for various hydrological applications.

Download Full-text

On The Estimation of Temporal Changes of Snow Water Equivalent by Spaceborne Sar Interferometry: A New Application for the Sentinel-1 Mission

Journal of Hydrology and Hydromechanics ◽

10.2478/johh-2018-0003 ◽

2019 ◽

Vol 67 (1) ◽

pp. 93-100 ◽

Cited By ~ 8

Author(s):

Vasco Conde ◽

Giovanni Nico ◽

Pedro Mateus ◽

João Catalão ◽

Anna Kontu ◽

...

Keyword(s):

Measurement Accuracy ◽

Snow Water Equivalent ◽

Temporal Variations ◽

Sar Interferometry ◽

Synthetic Aperture ◽

Snow Layer ◽

Illumination Condition ◽

Interferometric Phase ◽

Snow Water

Abstract In this work we present a methodology for the mapping of Snow Water Equivalent (SWE) temporal variations based on the Synthetic Aperture Radar (SAR) Interferometry technique and Sentinel-1 data. The shift in the interferometric phase caused by the refraction of the microwave signal penetrating the snow layer is isolated and exploited to generate maps of temporal variation of SWE from coherent SAR interferograms. The main advantage of the proposed methodology with respect to those based on the inversion of microwave SAR backscattering models is its simplicity and the reduced number of required in-situ SWE measurements. The maps, updated up to every 6 days, can attain a spatial resolution up to 20 m with sub-centimetre ΔSWE measurement accuracy in any weather and sun illumination condition. We present results obtained using the proposed methodology over a study area in Finland. These results are compared with in-situ measurements of ΔSWE, showing a reasonable match with a mean accuracy of about 6 mm.

Download Full-text

Representation of Snow in the Canadian Seasonal to Interannual Prediction System. Part I: Initialization

Journal of Hydrometeorology ◽

10.1175/jhm-d-14-0223.1 ◽

2016 ◽

Vol 17 (5) ◽

pp. 1467-1488 ◽

Cited By ~ 14

Author(s):

Reinel Sospedra-Alfonso ◽

Lawrence Mudryk ◽

William Merryfield ◽

Chris Derksen

Keyword(s):

Snow Cover ◽

Land Surface ◽

Snow Water Equivalent ◽

Initial Conditions ◽

Reanalysis Data ◽

Prediction System ◽

Snow Water ◽

System Part ◽

Surface Scheme

Abstract The ability of the Canadian Seasonal to Interannual Prediction System (CanSIPS) to provide realistic forecast initial conditions for snow cover is assessed using in situ measurements and gridded snow analyses. Forecast initial conditions for snow in CanCM3 and CanCM4 employed by CanSIPS are determined by the response of the Canadian Land Surface Scheme (CLASS) used in both models to forcing from model atmospheric fields constrained by assimilation of 6-hourly reanalysis data. These snow initial conditions are found to be representative of the daily climatology of snow water equivalent (SWE) as well as interannual variations in maximum SWE and the timing of snow onset and snowmelt observed at eight in situ measurement sites located across Canada. The level of this agreement is similar to that of three independent gridded snow analyses (MERRA, the European Space Agency’s GlobSnow, and an offline forced version of CLASS). Total Northern Hemisphere snow mass generated by the CanSIPS initialization procedure is larger for both models (especially CanCM3) than in MERRA, mostly because of higher SWE in regions of common snow cover. Globally, the interannual variability of initial SWE is found to correlate highly with that of MERRA in locations with appreciable snow. These initial values are compared to SWE in freely running CanCM3 and CanCM4 simulations produced without data assimilation of atmospheric fields. Differences in climatological SWE relative to MERRA are similar in the freely running and assimilating CanCM3 and CanCM4 simulations, suggesting that inherent model biases are a major contributor to biases in CanSIPS snow initial conditions.

Download Full-text

Incorporation of satellite-derived snow-cover area in spatial snowmelt modeling for a large area: determination of a gridded degree-day factor

Annals of Glaciology ◽

10.3189/2013aog62a218 ◽

2013 ◽

Vol 54 (62) ◽

pp. 205-213 ◽

Cited By ~ 11

Author(s):

Yoshihiro Asaoka ◽

Yuji Kominami

Keyword(s):

Snow Cover ◽

Snow Water Equivalent ◽

Sensible Heat Flux ◽

Spatial Uncertainty ◽

Large Area ◽

Snow Cover Area ◽

Degree Day ◽

Snow Water ◽

Snowmelt Modeling

AbstractSpatial degree-day factors (DDFs) are required for spatial snowmelt modeling over large areas by the degree-day method. We propose a method to obtain DDFs by incorporating snow disappearance dates (SDDs), derived from 10 day composites of Satellite Pour l’Observation de la Terre (SPOT)/VEGETATION data, into the degree-day method. This approach allowed determination of DDFs for each gridpoint so as to better reflect regional characteristics than use of spatially constant DDFs obtained from point measurements. Simulations at six observation sites successfully accounted for variations in snow water equivalent (SWE), even at elevations different from the closest measurement site. These results suggest that incorporating satellite-derived SDDs into the degree-day method decreases spatial uncertainty compared with the use of spatially constant DDFs. Application of our method to Japanese cold regions revealed that gridded DDFs were negatively correlated with accumulated positive degree-days (APDDs) and were high only when APDDs were low. These results imply that high DDFs resulted from the dominant contribution of solar radiation to snowmelt at low temperatures and that low DDFs resulted from a relatively high contribution of sensible heat flux at high temperatures. The proposed method seems to adequately account for the main energetic components of snowmelt during the snow-cover season over large areas.

Download Full-text

The role of liquid water percolation representation to estimate snow water equivalent in a Mediterranean mountain region (Mount Lebanon)

10.5194/hess-2019-514 ◽

2019 ◽

Author(s):

Abbas Fayad ◽

Simon Gascoin

Keyword(s):

Snow Cover ◽

Liquid Water ◽

Snow Depth ◽

Snow Water Equivalent ◽

Mountain Regions ◽

Snow Cover Area ◽

Water Percolation ◽

Snow Water ◽

Snow Model ◽

Snow Mass

Abstract. In many Mediterranean mountain regions, the seasonal snowpack is an essential yet poorly known water resource. Here, we examine, for the first time, the spatial distribution and evolution of the snow water equivalent (SWE) during three snow seasons (2013–2016) in the coastal mountains of Lebanon. We run SnowModel (Liston and Elder, 2006a), a spatially-distributed, process-based snow model, at 100 m resolution forced by new automatic weather station (AWS) data in three snow-dominated basins of Mount Lebanon. We evaluate a recent upgrade of the liquid water percolation scheme in SnowModel, which was introduced to improve the simulation of the snow water equivalent (SWE) and runoff in warm maritime regions. The model is evaluated against continuous snow depth and snow albedo observations at the AWS, manual SWE measurements, and MODIS snow cover area between 1200 m and 3000 m a.s.l.. The results show that the new percolation scheme yields better performance especially in terms of SWE but also in snow depth and snow cover area. Over the simulation period between 2013 and 2016, the maximum snow mass was reached between December and March. Peak mean SWE (above 1200 m a.s.l.) changed significantly from year to year in the three study catchments with values ranging between 73 mm and 286 mm we (RMSE between 160 and 260 mm w.e.). We suggest that the major sources of uncertainty in simulating the SWE, in this warm Mediterranean climate, can be attributed to forcing error but also to our limited understanding of the separation between rain and snow at lower-elevations, the transient snow melt events during the accumulation season, and the high-variability of snow depth patterns at the sub-pixel scale due to the wind-driven blown-snow redistribution into karstic features and sinkholes. Yet, the use of a process-based snow model with minimal requirements for parameter estimation provides a basis to simulate snow mass SWE in non-monitored catchments and characterize the contribution of snowmelt to the karstic groundwater recharge in Lebanon. While this research focused on three basins in the Mount Lebanon, it serves as a case study to highlight the importance of wet snow processes to estimate SWE in Mediterranean mountain regions.

Download Full-text

Climate sensitivity of snow water equivalent and snowmelt runoff in a Himalayan catchment

10.5194/tc-2016-216 ◽

2016 ◽

Cited By ~ 1

Author(s):

Emmy E. Stigter ◽

Niko Wanders ◽

Tuomo M. Saloranta ◽

Joseph M. Shea ◽

Marc F.P. Bierkens ◽

...

Keyword(s):

Kalman Filter ◽

Snow Cover ◽

Climate Sensitivity ◽

Snow Depth ◽

Snow Water Equivalent ◽

Snowmelt Runoff ◽

Snow Water ◽

Snow Model ◽

Increasing Temperature

Abstract. Snow is an important component of water storage in the Himalayas. Previous snowmelt studies in the Himalayas have predominantly relied on remotely sensed snow cover. However this provides no information on the actual amount of water stored in a snowpack i.e. the snow water equivalent (SWE). Therefore, in this study remotely sensed snow cover was combined with in situ meteorological observations and a modified version of the seNorge snow model to estimate climate sensitivity of SWE and snowmelt runoff in the Langtang catchment in Nepal. Landsat 8 and MOD10A2 snow cover maps were validated with in situ snow cover observations provided by surface temperature and snow depth measurements resulting in classification accuracies of 85.7 % and 83.1 % respectively. Optimal model parameter values were obtained through data assimilation of MOD10A2 snow maps and snow depth measurements using an Ensemble Kalman filter. The approach of modelling snow depth in a Kalman filter framework allows for data-constrained estimation of SWE rather than snow cover alone and this has great potential for future studies in the Himalayas. Climate sensitivity tests with the optimized snow model show a strong decrease in SWE in the valley with increasing temperature. However, at high elevation a decrease in SWE is (partly) compensated by an increase in precipitation, which emphasizes the need for accurate predictions on the changes in the spatial distribution of precipitation along with changes in temperature. Finally the climate sensitivity study revealed that snowmelt runoff increases in winter and early melt season (December to May) and decreases during the late melt season (June to September) as a result of the earlier onset of snowmelt due to increasing temperature.

Download Full-text

Canadian historical Snow Water Equivalent dataset (CanSWE, 1928–2020)

Earth System Science Data ◽

10.5194/essd-13-4603-2021 ◽

2021 ◽

Vol 13 (9) ◽

pp. 4603-4619

Author(s):

Vincent Vionnet ◽

Colleen Mortimer ◽

Mike Brady ◽

Louise Arnal ◽

Ross Brown

Keyword(s):

Snow Cover ◽

Newfoundland And Labrador ◽

Land Surface ◽

Snow Water Equivalent ◽

Water Security ◽

Monitoring And Evaluation ◽

Surface Models ◽

Snow Water ◽

The Government

Abstract. In situ measurements of water equivalent of snow cover (SWE) – the vertical depth of water that would be obtained if all the snow cover melted completely – are used in many applications including water management, flood forecasting, climate monitoring, and evaluation of hydrological and land surface models. The Canadian historical SWE dataset (CanSWE) combines manual and automated pan-Canadian SWE observations collected by national, provincial and territorial agencies as well as hydropower companies. Snow depth (SD) and bulk snow density (defined as the ratio of SWE to SD) are also included when available. This new dataset supersedes the previous Canadian Historical Snow Survey (CHSSD) dataset published by Brown et al. (2019), and this paper describes the efforts made to correct metadata, remove duplicate observations and quality control records. The CanSWE dataset was compiled from 15 different sources and includes SWE information for all provinces and territories that measure SWE. Data were updated to July 2020, and new historical data from the Government of Northwest Territories, Government of Newfoundland and Labrador, Saskatchewan Water Security Agency, and Hydro-Québec were included. CanSWE includes over 1 million SWE measurements from 2607 different locations across Canada over the period 1928–2020. It is publicly available at https://doi.org/10.5281/zenodo.4734371 (Vionnet et al., 2021).

Download Full-text

Assimilation of Sentinel-2 Data into a Snowpack Model in the High Atlas of Morocco

10.20944/preprints201810.0264.v1 ◽

2018 ◽

Author(s):

Mohamed Wassim Baba ◽

Simon Gascoin ◽

Lahoucine Hanich

Keyword(s):

Data Assimilation ◽

Snow Cover ◽

Snow Water Equivalent ◽

Snow Cover Area ◽

High Atlas ◽

Data Assimilation Scheme ◽

Snow Cover Extent ◽

Assimilation Scheme ◽

Sentinel 2

The snow melt from the High Atlas is a critical water resource in Morocco. In spite of its importance, monitoring the spatio-temporal evolution of key snow cover properties like the snow water equivalent remains challenging due to the lack of in situ measurements at high elevation. Since 2015, the Sentinel-2 mission provides high spatial resolution images with a 5 day revisit time, which offers new opportunities to characterize snow cover distribution in mountain regions. Here we present a new data assimilation scheme to estimate the state of the snowpack without in situ data. The model was forced using MERRA-2 data and a particle filter was developed to dynamically reduce the biases in temperature and precipitation using Sentinel-2 observations of the snow cover area. The assimilation scheme was implemented using SnowModel, a distributed energy-balance snowpack model and tested in a pilot catchment in the High Atlas. The study period covers 2015-2016 snow season which corresponds to the first operational year of Sentinel-2A, therefore the full revisit capacity was not yet achieved. Yet, we show that the data assimilation led to a better agreement with independent observations of the snow height at an automatic weather station and the snow cover extent from MODIS. The performance of the data assimilation scheme should benefit from the continuous improvements in MERRA-2 reanalyses and the full revisit capacity of Sentinel-2.

Download Full-text