scholarly journals Improving the rheological and fluid loss properties of the water-based mud using wheat flour

2021 ◽  
Vol 11 (1) ◽  
pp. 137-145
Author(s):  
Hani Ali Al Khalaf ◽  
Zeeshan Ahmad ◽  
Gabriella Kovácsné Federer
Keyword(s):  
Yield Point ◽  
Wheat Flour ◽  
Apparent Viscosity ◽  
Loss Rate ◽  
Drilling Fluid ◽  
Filter Press ◽  
Fluid Loss ◽  
Drilling Fluids ◽  
Water Based ◽  
Filtration Properties

This study aims to evaluate the effect of wheat flour as a natural and environmentally friendly material on the properties of water-based mud. Recently, many experiments have been conducted with various additives to improve the properties of drilling fluids. The effect of using wheat flour as a new additive to drilling fluid was studied to improve rheological and filtration properties. In the laboratory several samples of water-based mud were prepared, different concentrations of wheat flour from 1 wt% to 7 wt% were added to the mud and tested by using a Fann 35 viscometer, 140 Fann Mud balance, and an API LT-LP filter press. The results showed that adding 7 wt% of wheat flour was the optimal concentration. It was found that the apparent viscosity and yield point increased by 50% and 35%, respectively, when 7 wt% of wheat flour was added to the water-based drilling fluid. Likewise, the fluid loss rate was reduced by 25% when using the same concentration of wheat flour.

scholarly journals Lubricating Properties of Water-Based Drilling Fluid Improvement Using Lignite NPs as well as Their Effect on Rheological and Filtration Properties

2019 ◽  
Vol 26 (1) ◽  
pp. 81-88
Author(s):  
Massara Salam ◽  
Nada S. Al-Zubaidi ◽  
Asawer A. Al-Wasiti
Keyword(s):  
Oil And Gas ◽  
Drilling Fluid ◽  
Drill String ◽  
Filter Press ◽  
Drilling Fluids ◽  
Well Drilling ◽  
Water Based ◽  
Frictional Forces ◽  
Filtration Properties ◽  
Lubricating Properties

In the process of drilling directional, extended-reach, and horizontal wells, the frictional forces between the drill string and the wellbore or casing can cause severe problems including excessive torque which is one of the most important problems during drilling oil and gas well. Drilling fluid plays an important role by reducing these frictional forces. In this research, an enhancement of lubricating properties of drilling fluids was fundamentally examined by adding Lignite NPs into the water-based drilling fluid. Lubricity, Rheology and filtration properties of water-based drilling fluid were measured at room temperature using OFITE EP and Lubricity Tester, OFITE Model 900 Viscometer, and OFITE Low-Pressure Filter Press, respectively. Lignite NPs were added at different concentrations (0.05 %, 0.1 %, 0.2 %, 0.5 %, and 1 %) by weight into water-based drilling fluid. Lignite NPs showed good reduction in COF of water-based drilling fluid. The enhancement was increased with increasing Lignite NPs concentrations; 23.68%, 35.52%, and 45.3 % reduction in COF were obtained by adding 0.2%, 0.5%, and 1% by weight Lignite NPs concentration, respectively.

A Study on the Effects of Date Pit-Based Additive on the Performance of Water-Based Drilling Fluid

2017 ◽  
Vol 140 (5) ◽  
Author(s):  
Jimoh K. Adewole ◽  
Musa O. Najimu
Keyword(s):  
Thermal Stability ◽  
Particle Size ◽  
Filter Cake ◽  
Drilling Fluid ◽  
Fluid Loss ◽  
Drilling Fluids ◽  
Date Seed ◽  
Water Based ◽  
Filtration Properties ◽  
Loss Control

This study investigates the effect of using date seed-based additive on the performance of water-based drilling fluids (WBDFs). Specifically, the effects of date pit (DP) fat content, particle size, and DP loading on the drilling fluids density, rheological properties, filtration properties, and thermal stability were investigated. The results showed that dispersion of particles less than 75 μm DP into the WBDFs enhanced the rheological as well as fluid loss control properties. Optimum fluid loss and filter cake thickness can be achieved by addition of 15–20 wt % DP loading to drilling fluid formulation.

scholarly journals A Zwitterionic Copolymer as Rheology Modifier and Fluid Loss Agents for Water-Based Drilling Fluids

Polymers ◽  
2021 ◽  
Vol 13 (18) ◽  
pp. 3120
Author(s):  
Xianfeng Tan ◽  
Longchen Duan ◽  
Weichao Han ◽  
Ying Li ◽  
Mingyi Guo
Keyword(s):  
Zeta Potential ◽  
Negative Impact ◽  
Drilling Fluid ◽  
Fluid Loss ◽  
Drilling Fluids ◽  
High Concentration ◽  
Free Radical Copolymerization ◽  
Filtration Loss ◽  
Water Based ◽  
Filtration Properties

To overcome the negative impact on the rheological and filtration loss properties of drilling fluids caused by elevated temperature and salts contamination, which are common in ultradeep or geothermal drilling operations, it is imperative to develop highly efficient additives used in the water-based drilling fluid. In this study, a zwitterionic copolymer P (AM/DMC/AMPS/DMAM, ADAD) was synthesized by using acrylamide (AM), cationic monomer methacrylatoethyl trimethyl ammonium chloride (DMC), anionic monomer 2-acrylamide-2-methyl propane sulfonic acid (AMPS), and N,N-dimethylacrylamide (DMAM) through free radical copolymerization. The copolymer was characterized by 1H Nuclear Magnetic Resonance (NMR), Fourier transform infrared spectroscopy (FTIR), elemental analysis, thermogravimetric analysis (TGA), and zeta potential. The rheological behavior, filtration properties, and the performance exposure to salt or calcium contamination in water-based drilling fluid were investigated. The bentonite/polymer suspension showed improved rheological and filtration properties even after aging at 160 °C or a high concentration of salt and calcium. The filtration loss can be greatly reduced by more than 50% (from 18 mL to 7 mL) by the inclusion of 2.0 wt% copolymer, while a slight increase in the filtrate loss was observed even when exposed to electrolyte contamination. Particle size distribution and zeta potential further validate the idea that zwitterionic copolymer can greatly improve the stability of base fluid suspension through positive group enhanced anchoring on the clay surface and repulsion force between negative particles. Moreover, this study can be directed towards the design and application of zwitterionic copolymer in a water-based drilling fluid.

scholarly journals Comparison between the Effect of Local Katira Gum and Xanthan Gum on the Rheological Properties of Water-based Drilling Fluids

2020 ◽  
Vol 4 (2) ◽  
pp. 18
Author(s):  
Bayan Qadir Sofy Hussein ◽  
Khalid Mahmood Ismael Sharbazheri ◽  
Nabil Adiel Tayeb Ubaid
Keyword(s):  
Rheological Property ◽  
Rheological Properties ◽  
Yield Point ◽  
Experimental Work ◽  
Apparent Viscosity ◽  
Xanthan Gum ◽  
Drilling Fluid ◽  
Drilling Fluids ◽  
Drilling Mud ◽  
Water Based

The rheological properties of drilling fluids have an important role in providing a stable wellbore and eliminating the borehole problems. Several materials including polymers (xanthan gum) can be used to improve these properties. In this study, the effect of the local Katira, as a new polymer, on the rheological properties of the drilling fluids prepared as the bentonite-water-based mud has been investigated in comparison with the conventional xanthan gum. Experimental work was done to study of rheological properties of several gums such as, local katira gum, and xanthan gum bentonite drilling mud. Different samples of drilling fluids are prepared adding the xanthan gum and local katira to the base drilling fluid at different concentrations using Hamilton Beach mixer. The prepared samples are passed through rheological property tests including the apparent viscosity, plastic viscosity, and yield point (YP) under different temperature conditions. The obtained results show that the viscosity is increased from 5 to 8.5 cp and YP is increased from 18.5 to 30.5 lb/100 ft2, with increasing the concentration of the xanthan gum from 0.1 to 0.4. However, the effect of the local katira in increasing the viscosity and YP is lower compared with the xanthan gum, which are ranged between 5–6 cp and 18.5–20.5 cp.

Nanoparticles Performance as Fluid Loss Additives in Water Based Drilling Fluids

2016 ◽  
Vol 864 ◽  
pp. 189-193 ◽  
Author(s):  
Abdul Razak Ismail ◽  
Wan Rosli Wan Sulaiman ◽  
Mohd Zaidi Jaafar ◽  
Issham Ismail ◽  
Elisabet Sabu Hera
Keyword(s):  
Yield Point ◽  
Xanthan Gum ◽  
Drilling Fluid ◽  
High Surface ◽  
Volume Ratio ◽  
Gel Strength ◽  
Plastic Viscosity ◽  
Fluid Loss ◽  
Drilling Fluids ◽  
Water Based

Nanoparticles are used to study the rheological characteristics of drilling fluids. Nanoparticles have high surface to volume ratio, therefore only small quantity is required to blend in the drilling fluid. This research evaluates the performance of nanosilica and multi walled carbon nanotubes (MWCNT) as fluid loss additives in water based drilling fluid with various nanoparticles concentration and temperature. The results show that plastic viscosity, yield point and gel strength of drilling fluid increases as the concentration of nanoparticles increased. Drilling fluid with nanosilica gives the highest filtrate loss of 12 ml and mudcake thickness of 10 inch at 1 g concentration at 300°F. However, drilling fluid with MWCNT shows a decreasing trend in fluid loss and mudcake thickness. The results also show that xanthan gum containing 1 g of MWCNT gives 4.9 ml fluid loss and mudcake thickness of 4 inch at 200°F. After aging, plastic viscosity, yield point and gel strength of mud containing nanoparticles decrease significantly especially for 1 g of nanosilica and 0.01 g MWCNT. Fluid loss and mudcake thickness increased when the mud is exposed to temperature above 250°F. The results showed that xanthan gum with MWCNT gives a better rheological performance.

scholarly journals Experimental study on thermal, rheological and filtration control characteristics of drilling fluids: effect of nanoadditives

2020 ◽  
Vol 75 ◽  
pp. 36
Author(s):  
Erfan Veisi ◽  
Mastaneh Hajipour ◽  
Ebrahim Biniaz Delijani
Keyword(s):  
Thermal Conductivity ◽  
Heat Capacity ◽  
Drilling Fluid ◽  
Formation Damage ◽  
Fluid Loss ◽  
Drilling Fluids ◽  
Drill Bit ◽  
Rheological Characteristics ◽  
Cu Nanoparticles ◽  
Water Based

Cooling the drill bit is one of the major functions of drilling fluids, especially in high temperature deep drilling operations. Designing stable drilling fluids with proper thermal properties is a great challenge. Identifying appropriate additives for the drilling fluid can mitigate drill-bit erosion or deformation caused by induced thermal stress. The unique advantages of nanoparticles may enhance thermal characteristics of drilling fluids. The impacts of nanoparticles on the specific heat capacity, thermal conductivity, rheological, and filtration control characteristics of water‐based drilling fluids were experimentally investigated and compared in this study. Al2O3, CuO, and Cu nanoparticles were used to prepare the water-based drilling nanofluid samples with various concentrations, using the two-step method. Transmission Electron Microscopy (TEM) and X-Ray Diffraction (XRD) were utilized to study the nanoparticle samples. The nanofluids stability and particle size distribution were, furthermore, examined using Dynamic Light Scattering (DLS). The experimental results indicated that thermal and rheological characteristics are enhanced in the presence of nanoparticles. The best enhancement in drilling fluid heat capacity and thermal conductivity was obtained as 15.6% and 12%, respectively by adding 0.9 wt% Cu nanoparticles. Furthermore, significant improvement was observed in the rheological characteristics such as the apparent and plastic viscosities, yield point, and gel strength of the drilling nanofluids compared to the base drilling fluid. Addition of nanoparticles resulted in reduced fluid loss and formation damage. The permeability of filter cakes decreased with increasing the nanoparticles concentration, but no significant effect in filter cake thickness was observed. The results reveal that the application of nanoparticles may reduce drill-bit replacement costs by improving the thermal and drilling fluid rheological characteristics and decrease the formation damage due to mud filtrate invasion.

scholarly journals Laponite: a promising nanomaterial to formulate high-performance water-based drilling fluids

2020 ◽  
Author(s):  
Xian-Bin Huang ◽  
Jin-Sheng Sun ◽  
Yi Huang ◽  
Bang-Chuan Yan ◽  
Xiao-Dong Dong ◽  
...  
Keyword(s):  
High Performance ◽  
Drilling Fluid ◽  
Nitrogen Adsorption ◽  
Drill String ◽  
Wellbore Stability ◽  
Fluid Loss ◽  
Drilling Fluids ◽  
Mechanism Analysis ◽  
Water Based ◽  
Inhibition Performance

Abstract High-performance water-based drilling fluids (HPWBFs) are essential to wellbore stability in shale gas exploration and development. Laponite is a synthetic hectorite clay composed of disk-shaped nanoparticles. This paper analyzed the application potential of laponite in HPWBFs by evaluating its shale inhibition, plugging and lubrication performances. Shale inhibition performance was studied by linear swelling test and shale recovery test. Plugging performance was analyzed by nitrogen adsorption experiment and scanning electron microscope (SEM) observation. Extreme pressure lubricity test was used to evaluate the lubrication property. Experimental results show that laponite has good shale inhibition property, which is better than commonly used shale inhibitors, such as polyamine and KCl. Laponite can effectively plug shale pores. It considerably decreases the surface area and pore volume of shale, and SEM results show that it can reduce the porosity of shale and form a seamless nanofilm. Laponite is beneficial to increase lubricating property of drilling fluid by enhancing the drill pipes/wellbore interface smoothness and isolating the direct contact between wellbore and drill string. Besides, laponite can reduce the fluid loss volume. According to mechanism analysis, the good performance of laponite nanoparticles is mainly attributed to the disk-like nanostructure and the charged surfaces.

Can Titanium and Copper Oxide Commercial Nanoparticles Be Used for HP/HT Applications? A Comparison With the Very Well Performing Fe3O4 NP

2018 ◽  
Author(s):  
Zisis Vryzas ◽  
Vassilios C. Kelessidis ◽  
Lori Nalbandian ◽  
Vassilios Zaspalis
Keyword(s):  
Iron Oxide ◽  
Copper Oxide ◽  
Rheological Properties ◽  
Yield Stress ◽  
Base Fluid ◽  
Drilling Fluid ◽  
Filter Press ◽  
Fluid Loss ◽  
Drilling Fluids ◽  
Custom Made

Smart drilling fluids, which can change their properties according to the flow environment, must be carefully designed so that they can handle the difficult challenges of HP/HT drilling successfully. Due to their unique physico-chemical properties, nanoparticles (NP) are considered as very good candidates for the formulation of these smart drilling fluids. This study presents filtration and rheological results of newly developed high-performance water-based drilling fluid systems containing different nanoparticles, commercial (C) titanium oxide (TiO2) and commercial (C) copper oxide (CuO) NP and compares them with results from using custom-made (CM) iron oxide (Fe3O4) NP and commercial (C) iron oxide (Fe3O4) NP, previously reported. Novel nano-based drilling fluids were made of de-ionized water, 7 wt% commercial Na-bentonite (base fluid), and NP were added at 0.5 wt%. The rheological properties of the produced suspensions were measured at temperatures up to 60°C and at atmospheric pressure with a Couette-type viscometer. Filtration characteristics were determined at elevated pressures and temperatures in a HP/HT filter press (500 psi/176°C) using ceramic discs as filter media, of permeability, k = 775 mD. The results of this study showed that the samples containing 0.5 wt% C TiO2 caused a reduction in the fluid loss by 23%, while C CuO NP resulted in 16% reduction, when compared to that of the base fluid, at these HPHT conditions. This should be compared to the 47% and 34% reduction in fluid loss of 0.5% CM Fe3O4 NP and of 0.5% of C Fe3O4 NP, reported previously. Analysis of rheological data revealed shear-thinning behavior for all the tested novel drilling fluids. The samples containing TiO2 and CuO NP exhibited a yield stress less than that of the base fluid, compared to the increased yield stress observed for the C and CM Fe3O4 NP. This behavior can be attributed to the fact that TiO2 and CuO NP may also act as deflocculants and prevent the gelation of bentonite suspensions. This study shows that commercial nanoparticles of TiO2 and CuO do not perform as well as the Fe3O4 NP on filtration but provide drilling fluids with lower yield stresses, thus they could be considered as alternatives to Fe3O4 in situations where the rheological properties are critical.

Sign in / Sign up

Export Citation Format

Share Document