scholarly journals Relationship Between Compressive Strength and Splitting Tensile Strength of Palm Kernel Shell Concrete

2021 ◽  
Vol 7 (2) ◽  
Author(s):  
S. O. Odeyemi
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Palm Kernel ◽  
Physical Property ◽  
Lightweight Aggregate ◽  
Splitting Tensile Strength ◽  
Unit Weight ◽  
Palm Kernel Shell ◽  
Coarse Aggregates ◽  
Dry Unit Weight

The use of palm kernel shell (PKS) has gained acceptance in the production of concrete. Compressive strength is the mostly used strength characteristics of concrete. The compressive strength CS of concrete should provide a good basis for predicting the splitting tensile strength STS. The aim of this study is to establish a mathematical relationship between the CS and STS of concrete produced with PKS. In this study, coarse aggregates was fully replaced with PKS at varying water-cement ratios (w/c) for concrete mix ratios 1:1½:3 and 1:2:4. Unit weigth of the PKS, slump, compressive and splitting tesnsile strength were determined. A relationship between CS and STS was developed for the different w/c ratios using exponential function aproximation. Physical property tests carried out on the PKS characterized it as lightweight aggregate with saturated surface dry unit weight of 1.27. The slump revealed that PKS concrete at 0.3 and 0.4 w/c is stiff and not workable. CS and STS at 28day for mix ratio of 1:1½:3 at w/c of 0.3, 0.4, 0.5 and 0.6 were respectively 3.2 and 1.2; 9.4 and 2.1; 10.8 and 2.6; 9.0 and 2.4 N/mm2. The corresponding values obtained for mix ratio 1:2:4 were 3.0 and 1.0, 1.7 and 1.3, 4.5 and 1.6, 7.7 and 1.9N/mm2, respectively. Equations relating CS and STS at 0.3, 0.4, 0.5 and 0.6 w/c were established. It was concluded that PKS concrete produced with mix ratios 1:1½:3 and 1:2:4 performed better in compression and splitting tensile strength at w/c of 0.5 and 0.6.

scholarly journals Investigating the Performance of Palm Kernel Shells and Periwinkle Shells as Coarse Aggregates in Concrete

2020 ◽  
Vol 4 (1) ◽  
Author(s):  
O.J Oladiran ◽  
D.R Simeon ◽  
O.A Olatunde
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Lightweight Concrete ◽  
Palm Kernel ◽  
Specific Area ◽  
Light Weight ◽  
Palm Kernel Shell ◽  
Coarse Aggregates ◽  
Palm Kernel Shells ◽  
Periwinkle Shell

Excessive usage of materials is causing fast depletion of natural stone deposit. This study therefore investigates the performance of palm kernel shells (PKS) and periwinkle shells (PS) as alternatives coarse aggregates in concrete. Forty cubes and 40 cylinders each were produced with PKS and PS as replacement materials for granite. Series of tests were conducted to determine their performances. The results showed that, compressive and tensile strengths decrease as PKS and PS content increases, which allow specific area to increase, thus requiring more cement paste to bond effectively with the shells. The result also revealed that for all curing ages, palm kernel shell concrete (PKSC) have lower compressive strength and tensile strength than periwinkle shell concrete (PSC). The compressive strength and tensile strength of the 28-day PKSC with 100% replacement were 4.33 N/mm2 and 3.68 N/mm2 respectively; that of PSC at 100% replacement were 5.89 N/mm2 and 4.95 N/mm2 respectively; and granite concrete without any replacement were 25.11 N/mm2 and 11.74 N/mm2 respectively. It is concluded that both PKSC and PSC satisfied the compressive strength and tensile strength requirement of light weight concrete, although PS has better gradation and bonding to cement than PKS. This implies that PS is best suited as replacement for granite in lightweight concrete than PKS. It is recommended that the mix-ratio should be altered to get higher values of compressive strength; and both PKS and PS should be used for lightweight concretes.

Mechanical Properties of Fiber Reinforced Lightweight Aggregate Concrete

2011 ◽  
Vol 477 ◽  
pp. 274-279 ◽  
Author(s):  
Yi Xu ◽  
Lin Hua Jiang ◽  
Hong Qiang Chu ◽  
Lei Chen
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Compressive Strength ◽  
Water Hyacinth ◽  
Steel Fiber ◽  
Polypropylene Fiber ◽  
Lightweight Aggregate ◽  
Splitting Tensile Strength ◽  
Lightweight Aggregate Concrete ◽  
Fiber Types

In this study, the effects of fiber types on the mechanical properties of lightweight aggregate concretes were investigated. Three types of fibers, namely, polypropylene fiber, steel fiber and water hyacinth (Eichhornia crassipes) fiber, and two types of lightweight aggregates, namely, expanded polystyrene and ceramsite were used. The compressive strength and splitting tensile strength of concretes were tested. The results show that both the compressive strength and the splitting tensile strength were improved by adding a reasonable volume of steel fiber and polypropylene fiber into LWAC. The addition of water hyacinth fiber had little effect on the compressive strength of LWAC, while a little increase was observed in the splitting tensile strength.

scholarly journals Assessment of Workability and Compressive Strength of Rice Husk Ash-Blended Palm Kernel Shell Concrete

2021 ◽  
Vol 7 (1) ◽  
Author(s):  
K. O. Oriola
Keyword(s):  
Compressive Strength ◽  
Rice Husk ◽  
Rice Husk Ash ◽  
Construction Materials ◽  
Palm Kernel ◽  
Lightweight Aggregate ◽  
Strength Properties ◽  
Lightweight Aggregate Concrete ◽  
Palm Kernel Shell ◽  
Compressive Strength Of Concrete

The evaluation of agro-industrial by-products as alternative construction materials is becoming more significant as the demand for environmentally friendly construction materials increases. In this study, the workability and compressive strength of concrete produced by combining Palm Kernel Shell (PKS) and Rice Husk Ash (RHA) was investigated. Concrete mixes using a fixed content of 15% RHA as replacement for cement and 20, 40, 60, 80 and 100% PKS as replacement for crushed granite by volume with the mix ratios of 1:1½:3, 1:2:4 and 1:3:6 were produced. The water-to-cement ratios of 0.5, 0.6 and 0.7 were used for the respective mix ratios. Concrete without PKS and RHA served as control mix. The fresh concrete workability was evaluated through slump test. The concrete hardened properties determined were the density and compressive strength. The results indicated that the workability and density of PKSC were lower than control concrete, and they decreased as the PKS content in each mix ratio was increased. The compressive strength of concrete at 90 days decreased from 27.8-13.1 N/mm2, 23.8-8.9 N/mm2and 20.6-7.6 for 1:1½:3, 1:2:4 and 1:3:6, respectively as the substitution level of PKS increased from 0-100%. However, the compressive strength of concrete increased with curing age and the gain in strength of concrete containing RHA and PKSC were higher than the control at the later age. The concrete containing 15% RHA with up to 40% PKS for 1:1½:3 and 20% PKS for 1:2:4 mix ratios satisfied the minimum strength requirements for structural lightweight aggregate concrete (SLWAC) stipulated by the relevant standards. It can be concluded that the addition of 15% RHA is effective in improving the strength properties of PKSC for eco-friendly SLWAC production..

scholarly journals Mechanical and Structural Properties of a Lightweight Concrete with Different Types of Recycling Coarse Aggregate

2019 ◽  
Vol 26 (1) ◽  
pp. 33-40
Author(s):  
Muyasser M. Jomaa’h ◽  
Baraa Thaer Kamil ◽  
Omer S. Baghabra
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Compressive Strength ◽  
High Efficiency ◽  
Coarse Aggregate ◽  
Splitting Tensile Strength ◽  
Modulus Of Rupture ◽  
Unit Weight ◽  
Dry Density ◽  
Total Density

The light of the world’s technological development in the construction field and the continuous need to apply of a high-efficiency building materials because old methods is no longer is used after the advent of the solutions that characterized by fast applications and maximum protection in addition to reducing costs and increase the sustainability of the establishment and its design age. The lightweights of various installations are an urgent need to decrease the dead loads. Therefore, this study is specie locally focus on replacing the normal coarse aggregate with lightweight coarse aggregate (claystone (bonza), rubber, thermostone and polystyrene) in various volumetric ratios of (25, 50 and 75) % in addition to a preparation reference mix. For the purpose identifying and studying the important specifications the new concrete which contributes to the self-load reduction of the concrete by reducing the total density of the mixture, were prepared models of cylinders and standard prisms, to evaluate the compressive strength and the splitting tensile strength respectively, Also the modulus of rupture and the unit weight, where carried out. The results tests indicated that a drop in the mechanical properties of the concrete with increasing the lightweight coarse aggregate , mechanical properties values : compressive strength , rupture modulus, splitting tensile strength and flexural strength were between (10.66-28.99) MPa (1.122-3.372) MPa, (3.606-6.83) MPa and (20.101-25.874)MPa compared with a reference mixes (38.44MPa), (3.969MPa), (10.476MPa) and (26.940)MPa respectively for mixes of (25, 50 and75)% with different light coarse aggregate , also the values of an oven dry density were between (1665.5-2287.58)kg/m3 compared with reference mixes (2426.41kg/m³). The best concrete mix was (M7, M10) of low density (1598.4 kg/m3) and (1580.4) kg /m3 and the compression strength within the permissible limits (15.47) MPa.

Internal Curing of Saturated Lightweight Aggregate in High Performance Combined Concrete

2009 ◽  
Vol 405-406 ◽  
pp. 212-218
Author(s):  
Jin Zha ◽  
Bei Xing Li ◽  
Jin Hui Li ◽  
He Gao ◽  
Gong Cui
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
High Performance ◽  
Volume Fraction ◽  
Autogenous Shrinkage ◽  
Drying Shrinkage ◽  
Lightweight Aggregate ◽  
Splitting Tensile Strength ◽  
Hardened Concrete ◽  
Chloride Permeability

This paper investigated the mechanical properties, workability, autogenous shrinkage, drying shrinkage and durability of the high performance combined aggregate concrete with the coarse aggregate replaced by the lightweight aggregate in the volume fraction from 0% to 50%. The results demonstrated that the fresh concrete with the lightweight aggregate volume fraction of 10% and 30% had good workability, but degrade with a high volume fraction of 50 %. The hardened concrete with 10% and 30% lightweight aggregate replacement had similar compressive strength and splitting tensile strength comparing to the reference concrete without adding lightweight aggregate. The concrete with 50% lightweight aggregate replacement showed decreased compressive strength and splitting tensile strength. The concrete adding lightweight aggregate exhibited less autogenous shrinkage and drying shrinkage than the reference concrete without adding lightweight aggregate. The autogenous shrinkage and drying shrinkage increased with the increasing lightweight aggregate volume fraction. The concrete containing lightweight aggregate showed good durability after 200 freezing and thawing cycles, but the chloride permeability efficiency of concrete decreased.

Experiment on the Mechanical Performance of Fiber Lightweight Aggregate Concrete after Freeze-Thaw and Elevated Temperature

2014 ◽  
Vol 919-921 ◽  
pp. 1790-1793 ◽  
Author(s):  
Bo Cheng ◽  
Jing Huang ◽  
Wen Ting Jiang ◽  
Jian Min Wang
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Room Temperature ◽  
Mechanical Performance ◽  
Lightweight Aggregate ◽  
Splitting Tensile Strength ◽  
Lightweight Aggregate Concrete ◽  
Polyacrylonitrile Fiber ◽  
Aggregate Concrete ◽  
Freeze Thaw

Experiment on the compressive strength and splitting tensile strength of fiber lightweight aggregate concrete (FLWAC) after freeze-thaw cycling and high temperature was tested through blending polyvinyl alcohol fiber (PVAF) and polyacrylonitrile fiber (PANF) in aggregate concrete respectively. Five temperature levels, room temperature, 200°C, 400°C, 600°Cand 800°C were selected to heat the FLWAC test blocks after 25 times of freeze-thaw cycling. The micro-structure of FLWAC was observed through SEM. The experiment results show that, the cubic compressive strength of FLWAC is improved when the temperature is above 200°C, and the splitting tensile strength of FLWAC is obviously improved between the ranges from room temperature to 600°C. Blending fiber can weaken the brittle fracture performance of LWAC after freeze-thaw cycling at the peak loading state. However, the mass loss doesn’t have obvious improvement before and after 25 number of freeze-thaw cycling.

scholarly journals Mechanical Properties of Chopped Basalt Fiber-Reinforced Lightweight Aggregate Concrete and Chopped Polyacrylonitrile Fiber Reinforced Lightweight Aggregate Concrete

Materials ◽  
2020 ◽  
Vol 13 (7) ◽  
pp. 1715 ◽  
Author(s):  
Yusheng Zeng ◽  
Xianyu Zhou ◽  
Aiping Tang ◽  
Peng Sun
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Shear Strength ◽  
Water Absorption ◽  
Basalt Fiber ◽  
Lightweight Aggregate ◽  
Splitting Tensile Strength ◽  
Lightweight Aggregate Concrete ◽  
Polyacrylonitrile Fiber ◽  
Aggregate Concrete

In this study, an experimental investigation was conducted on the mechanical properties of lightweight aggregate concrete (LWAC) with different chopped fibers, including basalt fiber (BF) and polyacrylonitrile fiber (PANF). The LWAC performance was studied in regard to compressive strength, splitting tensile strength and shear strength at age of 28 days. In addition, the oven-dried density and water absorption were measured as well to confirm whether the specimens match the requirement of standard. In total, seven different mixture groups were designed and approximately 104 LWAC samples were tested. The test results showed that the oven-dried densities of the LWAC mixtures were in range of 1.819–1.844 t/m3 which satisfied the definition of LWAC by Chinese Standard. Additionally, water absorption decreased with the increasing of fiber content. The development tendency of the specific strength of LWAC was the same as that of the cube compressive strength. The addition of fibers had a significant effect on reducing water absorption. Adding BF and PANF into concrete had a relatively slight impact on the compressive strength but had an obvious effect on splitting tensile strength, flexural strength and shear strength enhancement, respectively. In that regard, a 1.5% fiber volume fraction of BF and PANF showed the maximum increase in strength. The use of BF and PANF could change the failure morphologies of splitting tensile and flexural destruction but almost had slight impact on the shear failure morphology. The strength enhancement parameter β was proposed to quantify the improvement effect of fibers on cube compressive strength, splitting tensile strength, flexural strength and shear strength, respectively. And the calculation results showed good agreement with test value.

Preparation and Properties of High-Performance Concrete with Ceramic Coarse Aggregate

2016 ◽  
Vol 852 ◽  
pp. 1413-1420
Author(s):  
Ben Ying Wu ◽  
Xi Wu Zhou ◽  
Jin Zhong Lu
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Silica Fume ◽  
High Performance ◽  
Coarse Aggregate ◽  
High Performance Concrete ◽  
Splitting Tensile Strength ◽  
Water Penetration ◽  
Concrete Material ◽  
Coarse Aggregates

High-performance concrete was prepared by using ceramic waste as coarse aggregate. The influences of several factors, such as the contents of ceramic coarse aggregates, fly ashes and silica fumes, on the properties of concrete material were investigated. The results show that the compressive strength of semi-porcelain coarse aggregate concrete are slightly lower than that of natural concrete, and the splitting tensile strength and the ratio of compressive strength and splitting tensile strength is similar to the ones of natural concrete. After fly ash and silica fume mixed, the compressive strength, the splitting tensile strength and the resistance to water penetration of concrete with semi-porcelain coarse aggregate increase significantly with the increase of silica fume content which meet the requirements of high-performance concrete. Concrete with orcelain coarse aggregate is only suitable for low strength concrete.

scholarly journals Strength properties of high-performance concretes with carbonate coarse aggregate

2011 ◽  
Vol 9 (2) ◽  
pp. 069-076
Author(s):  
Jacek Góra
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
High Performance ◽  
Coarse Aggregate ◽  
High Performance Concrete ◽  
Concrete Strength ◽  
Strength Properties ◽  
Splitting Tensile Strength ◽  
Coarse Aggregates

High performance concretes were tested to find an effect of the three different coarse aggregates (basalt, granite and dolomite) on concrete strength properties. All the results were analyzed statistically. Splitting tensile strength of high performance concrete with dolomite aggregate was significantly higher than that of concretes with basalt and granite aggregate. The effect of dolomite aggregate on compressive strength of HPC was much more advantageous than that of granite aggregate.

scholarly journals Mechanical Properties of Concrete with Bamboo Chips

2019 ◽  
Vol 9 (16) ◽  
pp. 3367
Author(s):  
Park ◽  
Hou ◽  
Lee ◽  
Jeong
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Compressive Strength ◽  
Compressive Stress ◽  
Modulus Of Elasticity ◽  
Concrete Specimen ◽  
Splitting Tensile Strength ◽  
Weak Bond ◽  
Coarse Aggregates ◽  
Potential Source

Mechanical properties of concrete with bamboo chips as a potential source of aggregates have been investigated in this study.The measurement of this investigation includes slump loss, compressive strength, strain at peak compressive stress, modulus of elasticity, compressive toughness ratio, and splitting tensile strength. A 0.5-cm-thick bamboo chip was cut to a 1 cm (width)× 1 cm (height) piece and then dried, wetted, and coated to minimize water absorption.The coarse aggregates in the concrete specimen were replaced with 10%, 20%, and 30% (by volume) of each bamboo chip. The testing results showed that the compressive strength and splitting tensile strength of concrete with bamboo chips decrease with increasing bamboo chip content (BCC). It is considered that the decrease of strengths is due to the weak bond between the mortar and the bamboo chip.

Sign in / Sign up

Export Citation Format

Share Document