scholarly journals Effect of Moldboard Plow Types on Soil Physical Properties Under Different Soil Moisture Content and Tractor Speed

2018 ◽  
Vol 31 (1) ◽  
pp. 48-58
Author(s):  
Aqeel J. Nassir
Keyword(s):  
Soil Moisture ◽  
Moisture Content ◽  
Physical Properties ◽  
Bulk Density ◽  
Soil Moisture Content ◽  
Penetration Resistance ◽  
Soil Physical Properties ◽  
Soil Porosity ◽  
Soil Penetration Resistance ◽  
Moldboard Plow

An experiment was conducted in fields of Agriculture college, University  of Basrah. The experiment was designed with split-spilt plots in Complete Randomized Blocks Design Treatments included three types of moldboard plows: helical,  semi digger and general –purpose, three soil moisture content levels (10.23,16.47 and 24.68%), and four tractor speed of 0.41, 0.56, 0.86 and 1.21 m sec -1  . The soil  physical properties were determined after plowing soil by using three types of moldboard plow. The results showed that there was significant effect of moldboard plow types, soil moisture content and tractor speed on soil physical properties including bulk density, soil porosity, soil penetration resistance and pulverization ratio. Results also indicated that the effect of interaction among plow types, soil moisture content and tractor speed was significantly on soil penetration resistance and pulverization ratios while it had not significantly effect on bulk density, soil porosity. In general, soil physical properties, had been improved when using high tractor speed and moderate soil moisture content whereas optimal operation was obtained when using general-purpose plow type and  high tractor speed of 1.12 m sec -1 and soil moisture content of 16.47% where this combination gives low bulk density (0.96Mg m-3), high soil porosity (63.90%) high soil pulverization ratio (74%) and low soil penetration resistance (623.47 kN m-2).

scholarly journals Pengaruh Frekuensi Pengolahan Tanah dan Pupuk Kompos terhadap Sifat Fisik Tanah dan Hasil Jagung

2019 ◽  
Vol 9 (2) ◽  
pp. 154
Author(s):  
I PUTU DHARMA ◽  
I NYOMAN PUJA
Keyword(s):  
Soil Moisture ◽  
Moisture Content ◽  
Physical Properties ◽  
Bulk Density ◽  
Soil Moisture Content ◽  
Block Design ◽  
Soil Physical Properties ◽  
Soil Tillage ◽  
Corn Yield ◽  
No Tillage

The Effect of Soil Tillages Frequency and Compost Fertilizer on Soil Physical Properties and Corn Yields. The aims of this research is to determine of effect soil tillage frequency and compost fertilizer on soil physical properties and corn yields. The method was used a Randomized Block Design (RBD), factorial consisting of two factors, namely: Soil Tillages Frequency (T) consists of 3 levels, namely: T0 = no tillage; T1 = if one time and T2 = if twice. Compost Fertilizer (K) consists of 3 levels, namely: K0 = Without compost, K1 = 5 tons compost/ha and B2 = 10 tons compost/ha. Combination treatment into 9 treatments, namely T0K0 , T0K1, T0K2, T1K0, T1K1, T1K2, T2K0, T2K1, T2K2. and each treatment was repeated 3 times, so there were 27 research plots.The results showed that the soil tillage frequency and compost fertilizer had no significant effect on the soil physical properties and corn yields. Twice soil tillage frequency resulted bulk density, porosity, soil moisture content and dry corn yields respectively 1.01 g/cm3, 60.98%, 37.31% and 0.83 kg/m2, and not significant different compared with no tillage which is 1.03 g/cm3, 60.43%, 36.57% and 0.81 kg/m2. Addition of 10 tons compost/ha resulted bulk density, porosity, soil moisture content and dry corn yield respectively 0.99 g/cm3, 61.75%, 38.21% and 0.86 kg/m2, and not significant different compared with without compost fertilizer which is 1.06 g/cm3, 59.40%, 36.44% and 0.80 kg/m2.

scholarly journals Assessing the Potential of Biochar for Improving Soil Physical Properties and Tree Growth

2021 ◽  
Vol 2021 ◽  
pp. 1-12
Author(s):  
Riziki Mwadalu ◽  
Benson Mochoge ◽  
Benjamin Danga
Keyword(s):  
Soil Moisture ◽  
Moisture Content ◽  
Physical Properties ◽  
Bulk Density ◽  
Tree Growth ◽  
Untreated Control ◽  
Soil Moisture Content ◽  
Application Rate ◽  
Soil Physical Properties ◽  
Collar Diameter

The effect of biochar on tree growth and soil physical properties as indicated in literature is still outstanding. Information on the effect of biochar on tree growth is limited, and the available literature has recorded conflicting results. Therefore, a field experiment using Casuarina equisetifolia (Casuarina) as the test crop under different biochar rates was conducted. Four biochar rates (0, 2.5, 5.0, and 7.5 t ha−1) were used as treatments, each replicated three times. Generally, biochar-amended plots recorded higher Casuarina height, collar diameter, and diameter at breast height (DBH). The application of biochar at 7.5 t ha−1 resulted in higher Casuarina height of up to 20.2% compared to the control. On the contrary, application of biochar at 2.5 t ha−1 recorded higher collar diameter of up to 30.2% compared to the control. Generally, there was a decrease in soil bulk density with biochar application. Bulk density decreased linearly with increasing biochar application rates with biochar application rate of 7.5 t ha−1 recording the lowest bulk density (0.99 g cm−3). There was a decrease in bulk density of up to 25% compared to the control with the biochar application rate of 7.5 t ha−1. Biochar application rate of 7.5 t ha−1 also recorded the highest soil moisture content across the assessment periods. Biochar-amended plots recorded higher soil moisture content than the untreated control. There was increase in soil moisture content following biochar application of up to 108% with the application of biochar at 7.5 t ha−1 compared to the untreated control. The increase in soil moisture content with biochar application can be attributed to biochar’s porous nature and large surface area. These results suggest that the use of biochar has the potential of enhancing Casuarina growth while enhancing soil physical properties by decreasing bulk density and enhancing soil moisture storage.

scholarly journals Impact of recreational transformation of soil physical properties on micromolluscs in an urban park

2021 ◽  
Vol 29 (2) ◽  
pp. 78-87
Author(s):  
V. S. Budakova ◽  
N. V. Yorkina ◽  
P. M. Telyuk ◽  
A. K. Umerova ◽  
O. M. Kunakh ◽  
...  
Keyword(s):  
Electrical Conductivity ◽  
Soil Moisture ◽  
Physical Properties ◽  
Soil Properties ◽  
Principal Component ◽  
Feature Space ◽  
Penetration Resistance ◽  
Soil Physical Properties ◽  
Urban Park ◽  
Soil Penetration Resistance

The paper assesses the effect of transformation of soil physical properties on the abundance of micromolluscs in the conditions of an urban park. The studies were carried out in Novooleksandrivskiy Park (Melitopol, Ukraine). An experimental polygon was represented by 7 transects with 18 sampling points in each. The interval between the points in the transect, as well as the interval between transects, was 3 meters. The total area of the polygon was 1,134 m2. The tree species growing within the polygon were Quercus robur, Sophora japonica, and Acer campestre. Shrubs were represented by Ulmus laevis, Tilia cordata, Celtis occidentalis, and Morus nigra. The locations of the trees and shrubs were mapped. The crowns of tree and shrub plants formed a dense canopy and a shady light regime. The grass cover was practically absent. The soil mechanical resistance, soil aggregate-size distribution, electrical conductivity of soil, soil moisture and bulk density were measured. We recorded 618 individuals of Vallonia pulchella, 120 individuals of Cochlicopa lubrica, and 58 individuals of Acanthinula aculeata within the surveyed polygon. We extracted three principal components, which could explain 60.9% of the variation in the feature space of the soil properties. The principal component 1 explained 42.0% of the variation of the feature space and depended on the soil penetration resistance throughout the whole profile, aggregate composition, density, electric conductivity and moisture content of soil. This component reflected a tendency for soil penetration resistance and soil density to increase near recreational trails. The principal component 1 was used to indicate the gradient of recreational transformation of the soil. The principal component 2 was able to explain 10.6% of the variation in the feature space. It negatively correlated with the distance from the recreational trail, soil penetration resistance at the depth of 35 cm or more, soil electrical conductivity, and the proportion of aggregates greater than 3 mm in size. This component positively correlated with soil penetration resistance at 0–5 cm depth and the proportion of aggregates less than 0.5 mm in size. This component can be interpreted as a "halo" from the recreational trail, or a gradient of indirect soil transformations adjacent to the zone of intense recreational load. The principal component 3 was able to explain 8.3% of the variation in the feature space. It positively correlated with soil penetration resistance at the depth of 20–40 cm, the proportion of 0.5–7.0 mm aggregates, and soil moisture. It negatively correlated with the proportion of aggregates larger than 7 mm and smaller than 0.25 mm. This component indicated a variation in soil properties that was induced by causes independent of recreational exposure. The extracted gradients of soil properties significantly influenced the abundance of micromollusc populations. The abundance of all species decreased after increase in recreational load. Micromollusc species responded to direct recreational exposure as plateau (C. lubrica) and asymmetric unimodal responses (V. pulchella and A. aculeata).

scholarly journals Effect of amount and time of incorporation of forest litter on soil physical properties

2020 ◽  
Vol 15 (2) ◽  
pp. 68-74
Author(s):  
Paardensha Ivy Chinir ◽  
Manoj Dutta ◽  
Rizongba Kichu ◽  
Sewak Ram
Keyword(s):  
Soil Moisture ◽  
Moisture Content ◽  
Physical Properties ◽  
Soil Moisture Content ◽  
Particle Density ◽  
Forest Litter ◽  
Soil Physical Properties ◽  
Mean Weight Diameter ◽  
The Difference ◽  
Water Holding

A field experiment was conducted to evaluate the effect of forest litter and its time of incorporation on soil physical properties. The study showed that plots with forest litter incorporated at 45 DBS (Days Before Sowing) had significantly higher soil moisture content as compared to those incorporated at 30 DBS after 30 and 60 DAS. However, the difference in the time of incorporation had no significant effect on soil moisture content at 90 DAS. At 30 DAS, application of forest litter @ 6 t ha-1 and 9 t ha-1 significantly increased the soil moisture content at a rate of 4.11 and 11.42 per cent, respectively over control. At 60 DAS, application of forest litter @ 3 t ha-1, 6 t ha-1 and 9 t ha-1 significantly increased the soil moisture content at the rate of 15.05, 17.26 and 25.65 per cent, respectively over control. At 90 DAS, a trend was noticed which showed that soil moisture content significantly increased at a progressive rate with each increase in the dose of forest litter application. At 90 DAS, the addition of forest litter @ 3 t ha-1, 6 t ha-1and 9 t ha-1 increased the soil moisture content @ 10.16, 17.84 and 22.20 per cent, respectively over control. The plots with forest litter incorporated at 45 DBS had significantly higher hydraulic conductivity, per cent aggregates and mean weight diameter as compared to those incorporated at 30 DBS. However, the difference in the time of incorporation i.e., at 30 and 45 DBS had no significant effect on bulk density, particle density and water holding capacity. Incorporation of forest litter @ 3 t ha-1, 6 t ha-1 and 9 t ha-1 significantly decreased the bulk density at the rate of 3.67, 8.65 and 14.14 per cent; while particle density increased at the rate of 2.59, 3.42 and 6.61 per cent, respectively when compared to control. The addition of forest litter @ 3 t ha-1, 6 t ha-1 and 9 t ha-1 resulted in a significant increase in water holding capacity and hydraulic conductivity at a rate of 3.72, 4.65 and 6.77 per cent and 24.13, 32.30 and 41.73 per cent, respectively over control. Further, the application of forest litter @ 3t ha-1, 6 t ha-1 and 9 t ha-1 significantly increased the per cent aggregate and mean weight diameter of the soil @ 1.77, 3.49 and 6.58 per cent 17.31, 26.28 and 41.35 per cent, respectively over control. The study revealed that incorporating 9 t ha-1 of forest litter at 45 DBS had the most beneficial effect on soil physical properties.

scholarly journals Data Grouping Method for the Purpose of Forecasting the Mechanical Strength of Plastic Soils

Agronomy ◽  
2020 ◽  
Vol 10 (4) ◽  
pp. 578
Author(s):  
Dariusz Błażejczak ◽  
Jan Jurga ◽  
Jarosław Pytka
Keyword(s):  
Soil Moisture ◽  
Moisture Content ◽  
Bulk Density ◽  
Field Measurements ◽  
Penetration Resistance ◽  
Soil Bulk Density ◽  
Regression Equations ◽  
Soil Penetration Resistance ◽  
Small Set ◽  
Data Grouping

The aim of this work was to develop a method of data grouping (DGM) that enables the selection of regression equations for forecasting soil penetration resistance based on an easily available and small set of input data: soil moisture content, soil bulk density and the grain size distribution of the soil. Models for forecasting the penetration resistance were created by selecting regression equations for specific intervals of granulometric variability of soil fractions. A field measurements campaign was conducted and soil samples were taken from the subsoil on 43 profiles, at depths of 25–30, 35–40, 45–50 and 55–60 cm. It was found that the dry bulk density is much less useful for predicting the penetration resistance of plastic soils than soil moisture. The study also showed that it is possible to forecast the soil penetration resistance on the basis of the gravimetric moisture content and the soil specific surface.

A survey on the soil penetration resistance and soil moisture content in field experiments

2011 ◽  
Vol 59 (4) ◽  
pp. 349-359
Author(s):  
P. Földesi ◽  
C. Gyuricza
Keyword(s):  
Soil Moisture ◽  
Moisture Content ◽  
Physical Condition ◽  
Soil Compaction ◽  
Field Experiments ◽  
Soil Moisture Content ◽  
Penetration Resistance ◽  
Soil Conditions ◽  
Environmental Damage ◽  
Soil Penetration Resistance

Various forms of physical soil degradation, including soil compaction, have been widely investigated both in Hungary and abroad. Soil compaction is a world-scale problem, which may be triggered by both natural and artificial factors and may adversely influence the effectiveness of crop production. In the long run this unfavourable change in the physical condition of the soil may result in extra expenses, higher energy consumption and excessive environmental damage. The effect of conventional tillage on the physical condition of the soil was assessed on six farms for three years in the framework of field experiments. In this study the physical condition of the soil was examined in terms of soil penetration resistance and moisture content. Significant differences between the experiments were revealed when penetration resistance (PR) was examinated at a depth of 20–30 cm, but not at other depths. In 2004 the mean PR values exceeded 3 MPa in experiments A, B and E. In 2005 significant differences were observed between the experiments at a depth of 30–40 cm, but no adverse compaction was detected at any depth in any of the experiments. In 2006 significant differences were observed between the experiments at depths of 0–10 cm and 10–20 cm, though even in that year no adverse soil compaction was detected. In the first year significant differences in soil moisture content were revealed at depths of 10–20 cm, 20–30 cm, 30–40 cm and 40–50 cm, and in 2005 at depths of 20–30 cm and 30–40 cm. In 2006 no significant differences were found between the experiments at any depth. The highest soil moisture contents were recorded in all the experiments at a depth of 30–40 cm. All in all, the results of both penetration resistance and moisture content were indicative of favourable soil conditions. During the period investigated adversely compact layers that would hamper moisture transport were not found in any of the experiments.

scholarly journals Dry matter productivity and soil physical properties after winter cover crops cultivation

2019 ◽  
pp. 362
Author(s):  
Katiely Aline Anschau Deimling ◽  
Edleusa Pereira Seidel ◽  
Jean Sérgio Rosset ◽  
Marcos Cesar Mottin ◽  
Daniela Da Rocha Herrmann ◽  
...  
Keyword(s):  
Physical Properties ◽  
Bulk Density ◽  
Cover Crops ◽  
Dry Matter ◽  
Penetration Resistance ◽  
Soil Physical Properties ◽  
Field Pea ◽  
Dry Matter Accumulation ◽  
Dry Matter Yield ◽  
Soil Penetration Resistance

The present study aimed to evaluate the dry matter yield of cover crops cultivated in monoculture and intercropped in a no-till system and its effects on the soil physical properties. The experimental design was of randomized blocks, with four replicates. Treatments used were black oat, black oat + forage radish, forage radish, black oat + field pea, field pea and the control (fallow). After 100 days after sowing the cover crops, the dry matter yield was evaluated, with the highest values found in the intercropped crops. After desiccation, undeformed soil samples were collected for the determination of macroporosity, microporosity, total porosity and soil bulk density in the 0 - 0,10; 0,10 - 0,20; 0,20 - 0,30 and 0,30 - 0,40 m layers. Soil penetration resistance was evaluated with a digital penetrometer. The intercrop of black oat with field pea and with forage radish provided the highest dry matter yield, showing the potential of dry matter accumulation in relation to monoculture. The cover crops were capable of improving the macroporosity, bulk density and soil penetration resistance when compared to the fallow area (control); however, they had no influence in soil aggregation due to the high compaction degree in the area.

In situ amelioration of sodic minespoil with chemical amendments and crop management: II. Soil physical properties, soil moisture and plant growth

1998 ◽  
Vol 78 (4) ◽  
pp. 667-674 ◽  
Author(s):  
J. J. Sansom ◽  
D. S. Chanasyk ◽  
M. A. Naeth ◽  
J. C. Bateman
Keyword(s):  
Soil Moisture ◽  
Physical Properties ◽  
Bulk Density ◽  
Sandy Loam ◽  
Canopy Cover ◽  
Crop Management ◽  
Ground Cover ◽  
Penetration Resistance ◽  
Soil Physical Properties ◽  
And Control

The effects of sulfur and gypsum amendments in conjunction with crop management (fallow/barley and forage) on soil physical properties, soil moisture and vegetation characteristics were measured on a sodic and calcareous sandy loam minespoil at the Highvale coal mine, west of Edmonton, Alberta.Amendment and crop management had no significant effect on bulk density, plant species composition, canopy cover, ground cover or annual aboveground biomass. Crop management significantly affected penetration resistance (which was generally higher under forage), while amendment treatments did not. Profile soil moisture was lowest within the gypsum-amended plots at all depths, and was similar for sulfur-amended and control plots. Crop management affected profile soil moisture, with significantly less moisture under continuous forage than fallow/barley. As percolation is critical to the effectiveness of amendments in the amelioration process, cereal/fallow rotations are more effective than continuous forage in facilitating that process. Key words: Reclamation, bulk density, penetration resistance

scholarly journals Characterizing Soil Physical Properties for Soil Moisture Monitoring with the North Carolina Environment and Climate Observing Network

2012 ◽  
Vol 29 (7) ◽  
pp. 933-943 ◽  
Author(s):  
Weinan Pan ◽  
R. P. Boyles ◽  
J. G. White ◽  
J. L. Heitman
Keyword(s):  
North Carolina ◽  
Soil Moisture ◽  
Physical Properties ◽  
Soil Properties ◽  
Water Content ◽  
Bulk Density ◽  
Soil Physical Properties ◽  
The North ◽  
Wide Range ◽  
Soil Moisture Monitoring

Abstract Soil moisture has important implications for meteorology, climatology, hydrology, and agriculture. This has led to growing interest in development of in situ soil moisture monitoring networks. Measurement interpretation is severely limited without soil property data. In North Carolina, soil moisture has been monitored since 1999 as a routine parameter in the statewide Environment and Climate Observing Network (ECONet), but with little soils information available for ECONet sites. The objective of this paper is to provide soils data for ECONet development. The authors studied soil physical properties at 27 ECONet sites and generated a database with 13 soil physical parameters, including sand, silt, and clay contents; bulk density; total porosity; saturated hydraulic conductivity; air-dried water content; and water retention at six pressures. Soil properties were highly variable among individual ECONet sites [coefficients of variation (CVs) ranging from 12% to 80%]. This wide range of properties suggests very different behavior among sites with respect to soil moisture. A principal component analysis indicated parameter groupings associated primarily with soil texture, bulk density, and air-dried water content accounted for 80% of the total variance in the dataset. These results suggested that a few specific soil properties could be measured to provide an understanding of differences in sites with respect to major soil properties. The authors also illustrate how the measured soil properties have been used to develop new soil moisture products and data screening for the North Carolina ECONet. The methods, analysis, and results presented here have applications to North Carolina and for other regions with heterogeneous soils where soil moisture monitoring is valuable.

Sign in / Sign up

Export Citation Format

Share Document