Slow Pyrolysis of Cystoseira Barbata Brown Macroalgae

2018 ◽  
Vol 69 (3) ◽  
pp. 553-556 ◽  
Author(s):  
Doinita Roxana Cioroiu ◽  
Oana Cristina Parvulescu ◽  
Tanase Dobre ◽  
Cristian Raducanu ◽  
Claudia Irina Koncsag ◽  
...  
Keyword(s):  
Carbon Dioxide ◽  
Fixed Bed ◽  
Fixed Bed Reactor ◽  
Bet Surface Area ◽  
Heat Flow Rate ◽  
Slow Pyrolysis ◽  
Process Factor ◽  
Bed Temperature ◽  
Cystoseira Barbata ◽  
Bio Oil

Slow pyrolysis of algal biomass of Cystoseira barbata was performed in a fixed bed reactor using carbon dioxide as a sweeping gas and a reactant in the process. Pyrolysis products consisted of a biochar, a bio-oil, and pyrolytic gases. According to a 23 factorial experiment, 8 tests were conducted for 1 hr at two levels of each process factor, i.e., specific heat flow rate (7540, 9215 W/m3), carbon dioxide superficial velocity (1.3, 2.6 cm/s), and bulk density of fixed bed biomass (221, 332 kg/m3). Correlations between these factors and final process responses in terms of mean bed temperature (461-663 oC), biochar yield (15.2-26.7%), bio-oil yield (29.9-34.8%), and BET surface area of biochar (45.17-91.12 m2/g) were established.

scholarly journals Valorization of Vine Prunings by Slow Pyrolysis in a Fixed-Bed Reactor

Processes ◽  
2021 ◽  
Vol 10 (1) ◽  
pp. 37
Author(s):  
Suzana Ioana Calcan ◽  
Oana Cristina Pârvulescu ◽  
Violeta Alexandra Ion ◽  
Cristian Eugen Răducanu ◽  
Liliana Bădulescu ◽  
...  
Keyword(s):  
Fixed Bed ◽  
Pyrolysis Product ◽  
Fixed Bed Reactor ◽  
Slow Pyrolysis ◽  
23 Factorial Design ◽  
Bed Temperature ◽  
Bio Oil ◽  
Mean Size ◽  
Ft Ir ◽  
Water Holding

The paper aimed at studying the slow pyrolysis of vine pruning waste in a fixed bed reactor and characterizing the pyrolysis products. Pyrolysis experiments were conducted for 60 min, using CO2 as a carrier gas and oxidizing agent. The distribution of biochar and bio-oil was dependent on variations in heat flux (4244–5777 W/m2), CO2 superficial velocity (0.004–0.008 m/s), and mean size of vegetal material (0.007–0.011 m). Relationships among these factors and process performances in terms of yields of biochar (0.286–0.328) and bio-oil (0.260–0.350), expressed as ratio between the final mass of pyrolysis product and initial mass of vegetal material, and final value of fixed bed temperature (401.1–486.5 °C) were established using a 23 factorial design. Proximate and ultimate analyses, FT-IR and SEM analyses, measurements of bulk density (0.112 ± 0.001 g/cm3), electrical conductivity (0.55 ± 0.03 dS/m), pH (10.35 ± 0.06), and water holding capacity (58.99 ± 14.51%) were performed for biochar. Water content (33.2 ± 1.27%), density (1.027 ± 0.014 g/cm3), pH (3.34 ± 0.02), refractive index (1.3553 ± 0.0027), and iodine value (87.98 ± 4.38 g I2/100 g bio-oil) were measured for bio-oil. Moreover, chemical composition of bio-oil was evaluated using GC-MS analysis, with 27 organic compounds being identified.

scholarly journals Study on the Product Characteristics of Pyrolysis Lignin with Calcium Salt Additives

Materials ◽  
2019 ◽  
Vol 12 (10) ◽  
pp. 1609 ◽  
Author(s):  
Yong Cui ◽  
Wenliang Wang ◽  
Jianmin Chang
Keyword(s):  
Calcium Salt ◽  
Fixed Bed ◽  
Value Added ◽  
Positive Influence ◽  
Fixed Bed Reactor ◽  
Bet Surface Area ◽  
Gas Chromatography Mass Spectrometry ◽  
Product Characteristics ◽  
Calcium Salts ◽  
Bio Oil

This study investigated and compared the product characteristics of pyrolysis lignin under different catalytic effects resulting from various calcium salts. The pyrolysis of lignin was conducted in a fixed-bed reactor with calcium salt additives, which included CaCl2, Ca(OH)2, and Ca(HCOO)2. The compositions of gas and bio-oil were detected using gas chromatography/mass spectrometry (GC/MS). The characterizations of chars were examined using Brunauer–Emmett–Teller (BET) surface area and scanning electron microscopy (SEM). The results indicate that all three types of calcium salts helped to promote bio-oil yield and inhibit gas and char from forming. Regarding the composition of gas products, calcium salt additives increased the concentrations of H2 and CH4 while decreasing the concentration of CO. In addition, calcium salt additives facilitated the formation of phenol and alkyl-phenols in bio-oil, but reduced the yields of guaiacol and vanillin, in the order CaCl2 < Ca(OH)2 < Ca(HCOO)2. Furthermore, when compared with the addition of CaCl2, the chars prepared by the addition of Ca(OH)2 and Ca(HCOO)2 had relatively higher BET surface areas. In conclusion, Ca(HCOO)2 had the greatest positive influence in regard to the product quality of lignin pyrolysis whilst also elevating the yield of value-added chemicals in bio-oils.

scholarly journals Bio-Oil Characterizations of Spirulina Platensis Residue (SPR) Pyrolysis Products for Renewable Energy Development

2020 ◽  
Vol 849 ◽  
pp. 47-52
Author(s):  
Siti Jamilatun ◽  
Aster Rahayu ◽  
Yano Surya Pradana ◽  
Budhijanto ◽  
Rochmadi ◽  
...  
Keyword(s):  
Renewable Energy ◽  
Spirulina Platensis ◽  
Pyrolysis Temperature ◽  
Renewable Energy Sources ◽  
Fixed Bed ◽  
Fixed Bed Reactor ◽  
Oil Yield ◽  
Optimum Temperature ◽  
Pyrolysis Products ◽  
Bio Oil

Nowadays, energy consumption has increased as a population increases with socio-economic developments and improved living standards. Therefore, it is necessary to find a replacement for fossil energy with renewable energy sources, and the potential to develop is biofuels. Bio-oil, water phase, gas, and char products will be produced by utilizing Spirulina platensis (SPR) microalgae extraction residue as pyrolysis raw material. The purpose of this study is to characterize pyrolysis products and bio-oil analysis with GC-MS. Quality fuel is good if O/C is low, H/C is high, HHV is high, and oxygenate compounds are low, but aliphatic and aromatic are high. Pyrolysis was carried out at a temperature of 300-600°C with a feed of 50 grams in atmospheric conditions with a heating rate of 5-35°C/min, the equipment used was a fixed-bed reactor. The higher the pyrolysis temperature, the higher the bio-oil yield will be to an optimum temperature, then lower. The optimum temperature of pyrolysis is 550°C with a bio-oil yield of 23.99 wt%. The higher the pyrolysis temperature, the higher the H/C, the lower O/C. The optimum condition was reached at a temperature of 500°C with the values of H/C, and O/C is 1.17 and 0.47. With an increase in temperature of 300-600°C, HHV increased from 11.64 MJ/kg to 20.63 MJ/kg, the oxygenate compound decreased from 85.26 to 37.55 wt%. Aliphatics and aromatics increased, respectively, from 5.76 to 36.72 wt% and 1.67 to 6.67 wt%.

Comparison of the Yield and Properties of Bio-Oil Produced by Slow and Fast Pyrolysis of Rice Husks and Coconut Shells

2014 ◽  
Vol 625 ◽  
pp. 626-629 ◽  
Author(s):  
Mandy Su Zan Gui ◽  
Seyed Amirmostafa Jourabchi ◽  
Hoon Kiat Ng ◽  
Suyin Gan
Keyword(s):  
Maximum Yield ◽  
Fast Pyrolysis ◽  
Fixed Bed ◽  
Fixed Bed Reactor ◽  
Rice Husks ◽  
Standard Procedures ◽  
Bio Oil ◽  
American Society ◽  
Coconut Shells ◽  
Lower Water Content

Slow pyrolysis (SP) and fast pyrolysis (FP) of rice husks, coconut shells and their mixtures were studied in a fixed bed reactor. The objectives of this study were to compare the yields and properties of bio-oils produced using SP and FP methods within a pyrolysis temperature range of 400 °C to 600 °C. Three different biomass compositions, 100% rice husks (RH), 100% coconut shells (CS) and a mixture of 50% rice husks with 50% of coconut shells (RH50/CS50) were experimented. In SP, the maximum yield of bio-oil for RH, CS and RH50/CS50 were 45.45%, 37.01%, 38.29% at temperatures of 550 °C, 500 °C and 600 °C respectively. As for FP, the maximum bio-oil yield obtained for RH, CS and RH50/CS50 were 50.52%, 40.14% and 42.25% at temperatures of 500 °C, 600 °C and 550 °C respectively. At these optimum pyrolysis temperatures, the percentage differences in bio oil yields for SP and FP were 10.57%, 8.11% and 9.83% for RH, CS and RH50/CS50 respectively. Based on American Society for Testing and Materials (ASTM) standard procedures, the properties of bio-oil were characterised and it was found that the bio oil produced by FP at optimum temperatures were less acidic, higher density, lower water content and viscosity as compared to the bio-oil produced by SP method for all biomass compositions.

Study of Catalytic Pyrolysis of Chlorella with γ-Al2O3 Catalyst

2013 ◽  
Vol 873 ◽  
pp. 562-566 ◽  
Author(s):  
Juan Liu ◽  
Xia Li ◽  
Qing Jie Guo
Keyword(s):  
Water Content ◽  
Molecular Sieve ◽  
Catalytic Pyrolysis ◽  
Fixed Bed ◽  
Fixed Bed Reactor ◽  
Pyrolysis Oil ◽  
Heating Value ◽  
Lower Viscosity ◽  
Bio Oil ◽  
Liquid Yield

Chlorella samples were pyrolysed in a fixed bed reactor with γ-Al2O3 or ZSM-5 molecular sieve catalyst at 600°C. Liquid oil samples was collected from pyrolysis experiments in a condenser and characterized for water content, kinematic viscosity and heating value. In the presence of catalysts , gas yield decreased and liquid yield increased when compared with non-catalytic pyrolysis at the same temperatures. Moreover, pyrolysis oil from catalytic with γ-Al2O3 runs carries lower water content and lower viscosity and higher heating value. Comparison of two catalytic products, the results were showed that γ-Al2O3 has a higher activity than that of ZSM-5 molecular sieve. The acidity distribution in these samples has been measured by t.p.d, of ammonia, the γ-Al2O3 shows a lower acidity. The γ-Al2O3 catalyst shows promise for production of high-quality bio-oil from algae via the catalytic pyrolysis.

scholarly journals Effect of CO2 partial pressure on dry reforming of ethanol for hydrogen production

2018 ◽  
Vol 1 (1) ◽  
pp. 6-10
Author(s):  
Fahim Fayaz ◽  
Ahmad Ziad Sulaiman ◽  
Sharanjit Singh ◽  
Sweeta Akbari
Keyword(s):  
Partial Pressure ◽  
Fixed Bed ◽  
Dry Reforming ◽  
Fixed Bed Reactor ◽  
Bet Surface Area ◽  
Impregnation Method ◽  
X Ray Diffraction ◽  
Co2 Partial Pressure ◽  
Temperature Programmed ◽  
Al2o3 Catalyst

The effect of CO2 partial pressure on ethanol dry reforming was evaluated over 5%Ce-10%Co/Al2O3 catalyst at = PCO2 = 20-50 kPa, PC2H5OH = 20 kPa, reaction temperature of 973 K under atmospheric pressure. The catalyst was prepared by using impregnation method and tested in a fixed-bed reactor. X-ray diffraction measurements studied the formation of Co3O4, spinel CoAl2O4 and CeO2, phases on surface of 5%Ce-10%Co/Al2O3 catalyst. CeO2, CoO and Co3O4 oxides were obtained during temperature–programmed calcination. Ce-promoted 10%Co/Al2O3 catalyst possessed high BET surface area of 137.35 m2 g-1. C2H5OH and CO2 conversions was improved with increasing CO2 partial pressure from 20-50 kPa whilst the optimal selectivity of H2 and CO was achieved at 50 kPa.

Sign in / Sign up

Export Citation Format

Share Document