scholarly journals Evaluation of photocatalytic activity of titanosilicate powders of synthetic origin

2021 ◽  
Vol 12 (2-2021) ◽  
pp. 273-278
Author(s):  
A. V. Tsyryatieva ◽  
◽  
V. V. Tyukavkina ◽  
Keyword(s):  
Methylene Blue ◽  
Photocatalytic Activity ◽  
Phase Composition ◽  
Visible Light ◽  
Specific Surface ◽  
The Self ◽  
Cement Stone ◽  
Light Sources ◽  
Self Cleaning ◽  
Imagej Software

In this work, a comparative study of the photocatalytic activity of synthetic titanosilicate powders with differences in phase composition and specific surface area was carried out. Evaluation of the efficiency of decomposition of the dye methylene blue in the presence of titanosilicate additives in an aqueous medium under ultraviolet and visible light sources is given. The self-cleaning ability of titanosilicate-modified cement stone was studied by exposure to ultraviolet and visible light using ImageJ software. The strength of a cement stone modified with a titanosilicate additive has been determined, and its ability to self-cleaning under the influence of ultraviolet and visible light has been studied.

Effect of Iron (III)-Doping on the Photocatalytic Activity of Titanium Dioxide Catalysts for Methylene Blue Degradation

2011 ◽  
Vol 117-119 ◽  
pp. 1088-1091
Author(s):  
Wen Churng Lin ◽  
Rui Liu ◽  
Wein Duo Yang
Keyword(s):  
Methylene Blue ◽  
Photocatalytic Activity ◽  
Visible Light ◽  
Specific Surface ◽  
Effective Means ◽  
Sol Gel ◽  
X Ray Diffraction ◽  
Surface Areas ◽  
Bet Specific Surface Area ◽  
Vis Spectroscopy

Iron-doped TiO2 photocatalyst powders were prepared by the sol–gel method and characterized by Brunauer–Emmett–Teller (BET)-specific surface area, scanning electron microscopy (SEM), X-ray diffraction (XRD), and Ultraviolet–Visible (UV-Vis) spectroscopy. Fe3+ doping in the TiO2 decreases the crystal grain size, increases the specific surface areas of powders, extends the absorption to visible light regions (400~500 nm), and lowers the photocatalytic activity for methylene blue (MB) degradation under UV irradiation. The photocatalytic degradation of MB in water was investigated as a function of the Fe3+ content in TiO2. It was found that under the irradiation of visible light, a small amount of Fe3+ dopant in TiO22 powders could obviously enhance the photocatalytic activity. When the Fe3+ content was in the range of 0.03–0.1 mol%, the photocatalytic activity of the samples was higher than that of undoped TiO2. Appropriate content of Fe-doping is an effective means to improve the photocatalytic activity of TiO2 for MB degradation under visible light irradiation.

scholarly journals Titanium dioxide modified with manganese: physicochemical and photocatalytic properties

2021 ◽  
Vol 12 (2-2021) ◽  
pp. 214-218
Author(s):  
S. A. Safaryan ◽  
◽  
M. L. Belikov ◽  
V. A. Krysanova ◽  
◽  
...  
Keyword(s):  
Methylene Blue ◽  
Titanium Dioxide ◽  
Photocatalytic Activity ◽  
Phase Composition ◽  
Specific Surface ◽  
Surface Area ◽  
Specific Surface Area ◽  
Organic Dyes ◽  
Photocatalytic Properties

The article presents the results of the studies of the physicochemical and photocatalytic properties of titanium dioxide modified with manganese, by the example of decomposition of organic dyes — ferroin and methylene blue. The correlations between the specific surface area and phase composition of the composites with their photocatalytic activity are revealed.

scholarly journals Improved Self-Cleaning Properties of Photocatalytic Gypsum Plaster Enriched with Glass Fiber

Materials ◽  
2019 ◽  
Vol 12 (3) ◽  
pp. 357 ◽  
Author(s):  
Kamila Zając ◽  
Magdalena Janus ◽  
Antoni Morawski
Keyword(s):  
Mechanical Properties ◽  
Methylene Blue ◽  
Titanium Dioxide ◽  
Photocatalytic Activity ◽  
Glass Fiber ◽  
Glass Fibers ◽  
The Self ◽  
Gypsum Plaster ◽  
Self Cleaning ◽  
Reactive Orange

In the study the self-cleaning properties of photoactive gypsum plasters are presented. The modified gypsum plasters were obtained by addition of 1 and 3 wt.% of nitrogen-modified titanium dioxide (TiO2/N) and 0.1, 0.3, and 0.5 wt.% of glass fiber. The self-cleaning ability of the obtained materials was tested during two dyes decomposition: Methylene Blue (MB) and Reactive Orange (RO). It was found that presence of glass fiber increased photocatalytic activity of modified gypsum plasters, which may be due to the fact glass fiber may act as ducts for light and transport it to sites screened by TiO2 or glass fiber can retard charge recombination. Moreover, unexpectedly the addition of glass fiber did not increase the mechanical properties of modified gypsum plasters, which may be because gypsum does not strongly adhere to the surface of glass fibers.

scholarly journals Self-Cleaning Polyester Fabric Prepared with TiOF2 and Hexadecyltrimethoxysilane

Polymers ◽  
2021 ◽  
Vol 13 (3) ◽  
pp. 387
Author(s):  
Euigyung Jeong ◽  
Heeju Woo ◽  
Yejin Moon ◽  
Dong Yun Lee ◽  
Minjung Jung ◽  
...  
Keyword(s):  
Methylene Blue ◽  
Contact Angle ◽  
Treatment Method ◽  
Polyester Fabric ◽  
Anatase Tio2 ◽  
The Self ◽  
Water Contact ◽  
Direct Fluorination ◽  
Tomato Ketchup ◽  
Self Cleaning

In this study, self-cleaning polyester (PET) fabrics were prepared using TiOF2 and hexadecyltrimethoxysilane(HDS) treatment. TiOF2 was synthesized via direct fluorination of a precursor TiO2 at various reaction temperatures. The prepared PET fabrics had superior photocatalytic self-cleaning properties compared with anatase TiO2/HDS-treated PET fabrics under UV and sunlight with 98% decomposition of methylene blue. TiOF2/HDS-treated PET fabrics also had superior superhydrophobic self-cleaning properties compared with anatase TiO2/HDS-treated PET fabrics with a 161° water contact angle and 6° roll-off angle. After the self-cleaning tests of the non-dyed TiOF2/HDS-treated PET fabrics, we prepared dyed TiOF2/HDS-treated PET fabrics to test practical aspects of the treatment method. These PET fabrics were barely stained by tomato ketchup; even when stained, they could be self-cleaned within 4 h. These results suggest that practical self-cleaning PET fabrics with superhydrophobicity and photocatalytic degradation could be prepared using TiOF2/HDS-treatment.

scholarly journals Real roles of perylene diimides for improving photocatalytic activity

RSC Advances ◽  
2020 ◽  
Vol 10 (39) ◽  
pp. 23024-23037 ◽  
Author(s):  
Fengxia Zhang ◽  
Wenjing Li ◽  
Tianyi Jiang ◽  
Xuemei Li ◽  
Yuanyuan Shao ◽  
...  
Keyword(s):  
Methylene Blue ◽  
Photocatalytic Activity ◽  
Visible Light ◽  
Hydrothermal Method ◽  
Perylene Diimides ◽  
Photodegradation Rate ◽  
Composite Photocatalysts ◽  
Visible Light Driven

Three novel visible-light-driven composite photocatalysts were synthesized by hydrothermal method. The effects of introducing PDIs with different structures into TiO2 were evaluated by assaying the photodegradation rate of methylene blue.

Enhanced photocatalytic activity of CeO2 using β-cyclodextrin on visible light assisted decoloration of methylene blue

2013 ◽  
Vol 69 (1) ◽  
pp. 113-119 ◽  
Author(s):  
Sakthivel Pitchaimuthu ◽  
Ponnusamy Velusamy
Keyword(s):  
Methylene Blue ◽  
Photocatalytic Activity ◽  
Visible Light ◽  
Inclusion Complexation ◽  
Processing Parameters ◽  
Operational Parameters ◽  
Illumination Time ◽  
Operational Conditions ◽  
Electron Microscopy Analysis ◽  
Initial Ph

An attempt has been made to enhance the photocatalytic activity of CeO2 for visible light assisted decoloration of methylene blue (MB) dye in aqueous solutions by β-cyclodextrin (β-CD). The inclusion complexation patterns between host and guest (i.e., β-CD and MB) have been confirmed with UV–visible spectral data. The interaction between CeO2 and β-CD has also been characterized by field emission scanning electron microscopy analysis. The photocatalytic activity of the catalyst under visible light was investigated by measuring the photodegradation of MB in aqueous solution. The effects of key operational parameters such as initial dye concentration, initial pH, CeO2 concentration as well as illumination time on the decolorization extents were investigated. Among the processing parameters, the pH of the reaction solution played an important role in tuning the photocatalytic activity of CeO2. The maximum photodecoloration rate was achieved at basic pH (pH 11). Under the optimum operational conditions, approximately 99.6% dye removal was achieved within 120 min. The observed results indicate that the decolorization of the MB followed a pseudo-first order kinetics.

Photocatalytic Degradation of Methylene Blue over Co-Ag3VO4 under Visible Light Irradiation

2011 ◽  
Vol 335-336 ◽  
pp. 1385-1390 ◽  
Author(s):  
Shuo Wiei Zhao ◽  
Hui Xu ◽  
Hua Ming Li ◽  
Yuan Guo Xu
Keyword(s):  
Methylene Blue ◽  
Photocatalytic Activity ◽  
Visible Light ◽  
Visible Light Irradiation ◽  
Absorption Edge ◽  
Diffuse Reflectance Spectroscopy ◽  
Dye Degradation ◽  
Light Irradiation ◽  
Experimental Conditions ◽  
X Ray

In order to improve the photocatalytic activity, Co was successfully loaded into Ag3VO4 by using impregnation process. The samples were characterized by X-ray diffraction (XRD), scanning electron microscope (SEM), energy-dispersive X-ray spectroscopy (EDS) and diffuse reflectance spectroscopy (DRS). The XRD and SEM–EDS analyses revealed that Co ion was dispersed on Ag3VO4. The DRS results indicated that the absorption edge of the Co–Ag3VO4 catalyst shifted to longer wavelength. The enhanced photocatalytic activity of Co–Ag3VO4 for Methylene Blue(MB) dye degradation under visible light irradiation was due to its wider absorption edge and higher separation rate of photo-generated electron and holes. In the experimental conditions, it is demonstrated that the MB was effectively degraded by more than 95% within 40 min when the Co–Ag3VO4 catalyst was calcined at 300°C with 1 wt.% Co content.

Hydrothermal Synthesis of Nanosized Titania Photocatalysts Using Novel Water-Soluble Titanium Complexes

2007 ◽  
Vol 124-126 ◽  
pp. 723-726 ◽  
Author(s):  
Makoto Kobayashi ◽  
Koji Tomita ◽  
Valery Petrykin ◽  
Shu Yin ◽  
Tsugio Sato ◽  
...  
Keyword(s):  
Photocatalytic Activity ◽  
Visible Light ◽  
Specific Surface ◽  
Single Phase ◽  
Visible Region ◽  
Water Soluble ◽  
No Oxidation ◽  
Nano Particles ◽  
Titanium Complexes ◽  
Uv Visible

Highly crystalline titania nano-particles were synthesized by hydrothermal method using novel stable water-soluble titanium complexes. It was confirmed that single phase anatase, rutile and brookite, which can be rarely synthesized as a single phase, can be obtained by varying the ligand in the complex and pH of the aqueous solution. TEM observations and BET specific surface area measurements had shown that these samples consisted of nanosized particles of 5~200 nm and had high specific surface areas of 25~150 m2/g. According to UV-visible diffuse reflectance spectra, these titania samples absorbed light in the visible region (λ > 400 nm). Photocatalytic activities in NO oxidation reaction exhibited by synthesized titania powders under the irradiation by UV- visible light were higher than the activity of the commercial TiO2 photocatalyst P25 (Degussa). Especially, under illumination by only visible light of above 510 nm wavelength, photocatalytic activity of the obtained specimens exceeded that of P25 more than four times. We also clearly demonstrated that single phase brookite had high photocatalytic activity for NO oxidation.

Controlling the morphology and composition of Ag/AgBr hybrid nanostructures and enhancing their visible light induced photocatalytic properties

RSC Advances ◽  
2016 ◽  
Vol 6 (60) ◽  
pp. 54709-54717 ◽  
Author(s):  
Aasim Shahzad ◽  
Taekyung Yu ◽  
Woo-Sik Kim
Keyword(s):  
Methylene Blue ◽  
Photocatalytic Activity ◽  
Visible Light ◽  
Hybrid Nanostructures ◽  
Photocatalytic Properties

Ag/AgBr hybrid nanostructures were prepared by reducing AgBr nanoparticles synthesized by reaction of Ag+ with Br−. The Ag/AgBr hybrid nanostructures exhibited enhanced photocatalytic activity and recyclability for decomposing methylene blue (MB).

Sign in / Sign up

Export Citation Format

Share Document