scholarly journals An Assessment of the Causes of Wellbore Instability and Stuck Pipe Occurrences in an Offshore Field, Niger Delta, Nigeria

2020 ◽  
Vol 1 (1) ◽  
Keyword(s):  
Cation Exchange ◽  
Niger Delta ◽  
Drilling Fluid ◽  
Wellbore Stability ◽  
Swelling Potential ◽  
Offshore Drilling ◽  
Wellbore Instability ◽  
Clay Swelling ◽  
Drilling Operations ◽  
Cationic Exchange

Wellbore instability and consequential stuck pipe issues are a common challenge associated with offshore drilling. Usually, the effect of wellbore instability is an increase in nonproductive time, possible loss of tools and costly drilling operations. Hence, there is a need for wellbore stability analyses before and during drilling operations. In “Agaza Field”, offshore Niger Delta, wellbore instability problems were encountered at various depths between 3,696-4,270 ft.; 5,000-5,425 ft. and 7,600-8000 ft. intervals. Sixty-five ditch-cutting samples and composite log plots obtained from both wells were and analyzed to determine the clay swelling potential and the cationic exchange between the formation and the drilling fluid as well as causes of formation instability. Agaza-1 well showed evidence of tight hole at intervals between 4,200 and 7,600 ft. In Agaza-2, there were indications of wellbore stresses from 1,908 ft. to 2,030 ft. However, deeper than 4,225ft depth, high fluctuation of pore pressure coincided with wellbore instability between 4,810 ft. and 5,200 ft. The principal clay minerals present within the formations are Illite, Smectite and Smectite/Illite interlayered types. Result of the cation exchange analysis showed that high concentration of calcium and sodium in the shale is responsible for high dissociation of the constituent minerals hence making the shales unstable. Analysis has shown that samples at some intervals from both wells are associated with high swelling potential while average cation exchange value is 40 meq/100g. Therefore, the primary cause of wellbore instability and stuck pipe within the studied intervals are attributed to high swelling and reactivity over time due to fluidformation interaction. Keywords: Clay cationic exchange, Clay swelling potential, Offshore drilling challenges, Reactive shales. African

Performance Evaluation of a Highly Inhibitive Water-Based Drilling Fluid for Ultralow Temperature Wells

2017 ◽  
Vol 140 (1) ◽  
Author(s):  
Xin Zhao ◽  
Zhengsong Qiu ◽  
Mingliang Wang ◽  
Weian Huang ◽  
Shifeng Zhang
Keyword(s):  
Drilling Fluid ◽  
Hydrate Formation ◽  
Wellbore Stability ◽  
Drilling Fluids ◽  
Offshore Drilling ◽  
Ultralow Temperature ◽  
Water Based ◽  
Drilling Operations ◽  
Inhibition Performance ◽  
Static Conditions

Drilling fluid with proper rheology, strong shale, and hydrate inhibition performance is essential for drilling ultralow temperature (as low as −5 °C) wells in deepwater and permafrost. In this study, the performance of drilling fluids together with additives for ultralow temperature wells has been evaluated by conducting the hydrate inhibition tests, shale inhibition tests, ultralow temperature rheology, and filtration tests. Thereafter, the formulation for a highly inhibitive water-based drilling fluid has been developed. The results show that 20 wt % NaCl can give at least a 16-h safe period for drilling operations at −5 °C and 15 MPa. Polyalcohol can effectively retard pore pressure transmission and filtrate invasion by sealing the wellbore above the cloud point, while polyetheramine can strongly inhibit shale hydration. Therefore, a combination of polyalcohol and polyetheramine can be used as an excellent shale stabilizer. The drilling fluid can prevent hydrate formation under both stirring and static conditions. Further, it can inhibit the swelling, dispersion, and collapse of shale samples, thereby enhancing wellbore stability. It has better rheological properties than the typical water-based drilling fluids used in onshore and offshore drilling at −5 °C to 75 °C. In addition, it can maintain stable rheology after being contaminated by 10 wt % NaCl, 1 wt % CaCl2, and 5 wt % shale cuttings. The drilling fluid developed in this study is therefore expected to perform well in drilling ultralow temperature wells.

Managing Wellbore Stability Window and Well Integrity by Adjusting the Tight Margin to Successfully Drill through Naturally Fractured Zone Onshore Niger Delta

2021 ◽  
Author(s):  
Bassey Akong ◽  
Samuel Orimoloye ◽  
Friday Otutu ◽  
Akinwale Ojo ◽  
Goodluck Mfonnom ◽  
...  
Keyword(s):  
Niger Delta ◽  
Wellbore Stability ◽  
Rock Properties ◽  
Failure Behavior ◽  
Natural Fractures ◽  
Gas Well ◽  
Well Integrity ◽  
Trajectory Formation ◽  
Naturally Fractured ◽  
Drilling Operations

Abstract The analysis of wellbore stability in gas wells is vital for effective drilling operations, especially in Brown fields and for modern drilling technologies. Tensile failure mode of Wellbore stability problems usually occur when drilling through hydrocarbon formations such as shale, unconsolidated sandstone, sand units, natural fractured formations and HPHT formations with narrow safety mud window. These problems can significantly affect drilling time, costs and the whole drilling operations. In the case of the candidate onshore gas well Niger Delta, there was severe lost circulation events and gas cut mud while drilling. However, there was need for a consistent adjustment of the tight drilling margin, flow, and mud rheology to allow for effective filter-cake formation around the penetrated natural fractures and traversed depleted intervals without jeopardizing the well integrity. Several assumptions were validly made for formations with voids or natural fractures, because the presence of these geological features influenced rock anisotropic properties, wellbore stress concentration and failure behavior with end point of partial – to-total loss circulation events. This was a complicated phenomenon, because the pre-drilled stress distribution simulation around the candidate wellbore was investigated to be affected by factors such as rock properties, far-field principal stresses, wellbore trajectory, formation pore pressure, reservoir and drilling fluids properties and time without much interest on traversing through voids or naturally fractured layers. This study reviews the major causes of the severe losses encountered, the adopted fractured permeability mid-line mudweight window mitigation process, stress caging strategies and other operational decisions adopted to further salvage and drill through the naturally fractured and depleted intervals, hence regaining the well integrity by reducing NPT and promoting well-early-time-production for the onshore gas well Niger Delta.

Interdisciplinary Approach for Wellbore Stability During Slimhole Drilling at Volga-Urals Basin Oilfield

2021 ◽  
Author(s):  
Anna Vladimirovna Norkina ◽  
Sergey Mihailovich Karpukhin ◽  
Konstantin Urjevich Ruban ◽  
Yuriy Anatoljevich Petrakov ◽  
Alexey Evgenjevich Sobolev
Keyword(s):  
Drilling Fluid ◽  
Interdisciplinary Approach ◽  
Wellbore Stability ◽  
Vertical Wells ◽  
Wellbore Instability ◽  
Water Based ◽  
Chemical Studies ◽  
Fluid Rheology ◽  
Selection Of

Abstract The design features and the need to use a water-based solution make the task of ensuring trouble-free drilling of vertical wells non-trivial. This work is an example of an interdisciplinary approach to the analysis of the mechanisms of instability of the wellbore. Instability can be caused by a complex of reasons, in this case, standard geomechanical calculations are not enough to solve the problem. Engineering calculations and laboratory chemical studies are integrated into the process of geomechanical modeling. The recommendations developed in all three areas are interdependent and inseparable from each other. To achieve good results, it is necessary to comply with a set of measures at the same time. The key tasks of the project were: determination of drilling density, tripping the pipe conditions, parameters of the drilling fluid rheology, selection of a system for the best inhibition of clay swelling.

scholarly journals Oil-Based Drilling Fluid Plugging Method for Strengthening Wellbore Stability of Shale Gas

Geofluids ◽  
2021 ◽  
Vol 2021 ◽  
pp. 1-13
Author(s):  
Pengcheng Wu ◽  
Chengxu Zhong ◽  
Zhengtao Li ◽  
Zhen Zhang ◽  
Zhiyuan Wang ◽  
...  
Keyword(s):  
Shale Gas ◽  
Drilling Fluid ◽  
Wellbore Stability ◽  
Drilling Fluids ◽  
Fluid System ◽  
Horizontal Drilling ◽  
Wellbore Instability ◽  
Filtration Loss ◽  
Treatment Agent ◽  
Stability Method

Finding out the reasons for wellbore instability in the Longmaxi Formation and Wufeng Formation and putting forward drilling fluid technical countermeasures to strengthen and stabilize the wellbore are very crucial to horizontal drilling. Based on X-ray diffraction, electron microscope scanning, linear swelling experiment, and hot-rolling dispersion experiment, the physicochemical mechanism of wellbore instability in complex strata was revealed, and thus, the coordinated wellbore stability method can be put forward, which is “strengthening plugging of micropores, inhibiting filtrate invasion, and retarding pressure transmission.” Using a sand bed filtration tester, high-temperature and high-pressure plugging simulation experimental device, and microporous membrane and other experimental devices, the oil-based drilling fluid treatment agent was researched and selected, and a set of an enhanced plugging drilling fluid system suitable for shale gas horizontal well was constructed. Its temperature resistance is 135°C and it has preferable contamination resistibility (10% NaCl, 1% CaCl2, and 8% poor clay). The bearing capacity of a 400 μm fracture is 5 MPa, and the filtration loss of 0.22 μm and 0.45 μm microporous membranes is zero. Compared with previous field drilling fluids, the constructed oil-based drilling fluid system has a greatly improved plugging ability and excellent performance in other aspects.

SUMHOLE DRILLING: WELLBORE STABILITY CONSIDERATIONS BASED UPON FIELD AND LABORATORY DATA

1996 ◽  
Vol 36 (1) ◽  
pp. 544
Author(s):  
M.A. Addis ◽  
R.G. Jeffrey
Keyword(s):  
Field Data ◽  
Drilling Fluid ◽  
Laboratory Data ◽  
Petroleum Industry ◽  
Cost Savings ◽  
Wellbore Stability ◽  
Wellbore Instability ◽  
Attractive Option ◽  
Different Diameters ◽  
Fluid Design

Slimhole drilling is becoming an attractive option as it provides significant cost savings in the petroleum industry. Furthermore, many of the technical obstacles in adapting slimhole drilling for the petroleum industry have been addressed, such as rig modifications, small volume kick detection, drilling fluid design, etc. However, wellbore stability in slimholes is largely taken for granted, when it could potentially increase costs dramatically. In this paper, a review of the available information on the effects of hole size on hole stability is presented. Wellbore stability in holes of different diameters is discussed qualitatively based on published laboratory data and unpublished field data. The quantitative assessment of wellbore instability in slimholes is addressed using observations of instability in a well in which the far field stresses were measured.The field data presented here suggest that slimhole wells are not more stable than conventional wells. The slimhole drilled in NSW shows that even using the most conservative prediction model, wellbore instability would not be predicted—instability was however, observed.

Wellbore Shielding Technique Increases Operative Window, Avoiding Formation Instability and Losses, Minimizing NPT, and Optimizing Drilling Operations in the Unconventional Plays

2021 ◽  
Author(s):  
Gaston Lopez ◽  
Gonzalo Vidal ◽  
Claus Hedegaard ◽  
Reinaldo Maldonado
Keyword(s):  
Drilling Fluid ◽  
Drilling Fluids ◽  
Wellbore Instability ◽  
Lost Circulation ◽  
Drilling Performance ◽  
Drilling Parameters ◽  
Vaca Muerta ◽  
Drilling Operations ◽  
Fracture Gradient ◽  
Vaca Muerta Formation

Abstract Losses, wellbore instability, and influxes during drillings operations in unconventional fields result from continuous reactivity to the drilling fluid causing instability in the microfractured limestone of the Quintuco Formation in Argentina. This volatile situation becomes more critical when drilling operations are navigating horizontally through the Vaca Muerta Formation, a bituminous marlstone with a higher density than the Quintuco Formation. Controlling drilling fluids invasion between the communicating microfractures and connecting pores helps to minimize seepage losses, total losses, wellbore fluid influxes, and instabilities, reducing the non-productive time (NPT) caused by these problems during drilling operations. The use of conventional sealants – like calcium carbonate, graphite, asphalt, and other bridging materials – does not guarantee problem-free drilling operations. Also, lost circulation material (LCM) is restricted because the MWD-LWD tools clearances are very narrow in these slim holes. The challenge is to generate a strong and resistant seal separating the drilling fluid and the formation. Using an ultra-low-invasion technology will increase the operative fracture gradient window, avoid fluid invasion to the formation, minimize losses, and stop the cycle of fluid invasion and instability, allowing operations to maintain the designed drilling parameters and objectives safely. The ultra-low-invasion wellbore shielding technology has been applied in various fields, resulting in significantly improved drilling efficiencies compared to offset wells. The operator has benefited from the minimization of drilling fluids costs and optimization in drilling operations, including reducing the volume of oil-based drilling fluids used per well, fewer casing sections, and fewer requirements for cementing intervals to solve lost circulation problems. This paper will discuss the design of the ultra-low-invasion technology in an oil-based drilling fluid, the strategy for determining the technical limits for application, the evaluation of the operative window with an increase in the fracture gradient, the optimized drilling performance, and reduction in costs, including the elimination of NPT caused by wellbore instability.

Machine Learning Applications in Drilling Fluid Engineering: a Review

2021 ◽  
Author(s):  
Sercan Gul
Keyword(s):  
Machine Learning ◽  
Oil And Gas ◽  
Drilling Fluid ◽  
Wellbore Stability ◽  
Drilling Fluids ◽  
Fluid Mud ◽  
Surface Cooling ◽  
Real Time Analysis ◽  
Machine Learning Applications ◽  
Drilling Operations

Abstract Drilling fluid (mud) serves various purposes in drilling operations, the most important being the primary well control barrier to prevent kicks and blowouts. Other duties include, but not limited to, maintaining wellbore stability, removing and transporting formation cuttings to the surface, cooling and lubricating downhole tools, and transmitting hydraulic energy to the drill bit. Mud quality is therefore related to most of the problems in drilling operations either directly or indirectly. The physics-based models used in the industry with drilling fluid information (i.e., cuttings transport, well hydraulics, event detection) are computationally expensive, difficult to integrate for real-time analysis, and not always applicable for all drilling conditions. For this reason, researchers have shown extensive interest in machine learning (ML) approaches to alleviate their fluid-related problems. In this study, a comprehensive review of the abundant literature on the various applications of ML in oil and gas operations, concentrating mainly on drilling fluids, is presented. It was shown that leveraging state-of-the-art supervised and unsupervised ML methods can help predict or eliminate most fluid-related issues in drilling. The review discusses various ML methods, their theory, applications, limitations, and achievements.

scholarly journals A novel alkali-surfactant for optimization of filtercake removal in oil–gas well

2022 ◽  
Author(s):  
Kevin Nsolloh Lichinga ◽  
Amos Luanda ◽  
Mtabazi Geofrey Sahini
Keyword(s):  
Drilling Fluid ◽  
Reynold Number ◽  
Active Species ◽  
Cleaning Efficiency ◽  
Wellbore Instability ◽  
Polar Components ◽  
Number Of Factors ◽  
Turbulent Flow Regime ◽  
Drilling Operations ◽  
Oil Gas

AbstractThe main objective of this study is to improve the oil-based filtercake removal at the wellbore second interface through chemical method. The reductions in near-well permeability, bonding strength at wellbore second interface and acidizing treatment are the critical problems in oilfield upstream operations. One of the major causes has been identified as drilling fluid filtrate invasion during the drilling operations. This as result leads to near-well reduction in-flow capacity due to high drawdown pressure and wellbore instability. A number of chemical methods such as enzymes, acids, oxidizers, or their hybrids, have been used, however, due to the presence of a number of factors prior to its removal, there are still many challenges in cleaning oil-based filtercake from the wellbore surface. There is a need for development an effective method for improving oil-based filtercake removal. This study presents a novel Alkali-Surfactant (KV-MA) solution developed in the laboratory to optimize the filtercake removal of oil–gas wellbore. The Reynold number for KV-MA solution was found to be 9,068 indicating that turbulent flow regime will dominate in the annulus which enhances the cleaning efficiency. The wettability test established that, contact angle of 14° was a proper wetting agent. The calculated cleaning efficiency was 86.9%, indicating that it can effectively remove the oil-based filtercake. NaOH reacts with the polar components in the oil phase of the oil-based filtercake to produce ionized surface-active species; hence reducing the Interfacial Tension. Surfactant quickens the diffusion of ionized species from the interface to the bulk phase.

Treatment of Prodigious Reactive Shale in the Permian Basin Using High-Performance Drilling Fluid: A Successful Case Study

2021 ◽  
Author(s):  
Almostafa Alhadi ◽  
Musaab Magzoub
Keyword(s):  
Emulsion Stability ◽  
Drilling Fluid ◽  
Treatment Plan ◽  
Wellbore Stability ◽  
Wetting Agent ◽  
Water Phase ◽  
Permian Basin ◽  
Wellbore Instability ◽  
Hole Cleaning ◽  
Rock Samples

Abstract In the Permian basin, Spraberry Trend is one of the formations that markedly contribute to the unconventional shale production in the U.S. lately. Unusual shale reactivity was encountered while drilling several horizontal wells, leading to wellbore instability issues. Consequently, shakers’ screens blockage increased the mud losses and drilling time, leading to an increased non-productive time (NPT). This paper addresses the challenges and causes of the formation instability issues resulted from shale interaction with the used drilling fluid and presents the timely actions taken to mitigate such problems. During the drilling operation, several rock samples were collected at different depth intervals from the shale shaker. Rock samples were analyzed to identify the clay and minerals contents in the formations. The collected samples were first cleaned to remove the mud, dried, ground, and then characterized by an X-ray diffraction test (XRD) and microscopic imaging. After identifying the possible reasons for the wellbore instability, several timely actions were taken to mitigate this issue. These actions include: 1) increasing the emulsion stability, 2) increasing the water phase salinity (WPS), 3) decreasing the water phase volume, 4) adding wetting agent, 5) using wider screens for the shaker, and 6) controlling drilling parameters such as weight on bit and rotational speed. Afterward, wellbore stability, well control problem indicators, and drilling fluid properties, especially rheology, were closely monitored to identify any subsequent or unusual events. The geological and mineralogy studies show that the drilled formation contains high smectite and illite clay content, up to 49%, which was believed to be the main reason for the unusual shale reactivity. Replacing the existing screens (200 API) with wider screens (160 and 140 API) showed an insignificant effect in mitigating the screens blockage. The adopted method of reducing the rate of penetration (ROP) and increasing the circulation time helped significantly alleviate the screens blockage by reducing the cuttings production and giving more time for hole cleaning. Furthermore, the optimal hole cleaning successfully increased the formation's stability. Adding a wetting agent to the drilling mud did not impact the cuttings aggregations; however, it led to a decrease in the rheological properties; thus, adding more concentration of the viscosifier was required to maintain the fluid rheology. Increasing the water phase salinity (WPS) to over 230k ppm and the emulsion stability to over 700 mV was considered the backbone of the treatment plan that significantly resolved the issue by inhibiting the clay. Eventually, the critical considerations were pointed out.

The Influence of SiO2 and TiO2 Nanoparticles on the Properties of Water-Based Mud

2017 ◽  
Author(s):  
Petar Mijić ◽  
Nediljka Gaurina-Međimurec ◽  
Borivoje Pašić
Keyword(s):  
Filter Cake ◽  
Drilling Fluid ◽  
Wellbore Stability ◽  
Drilling Fluids ◽  
Drilling Mud ◽  
Shale Formations ◽  
Wellbore Instability ◽  
Water Based ◽  
Fluid Properties

About 75% of all formations drilled worldwide are shale formations and 90% of all wellbore instability problems occur in shale formations. This increases the overall cost of drilling. Therefore, drilling through shale formations, which have nanosized pores with nanodarcy permeability still need better solutions since the additives used in the conventional drilling fluids are too large to plug them. One of the solutions to drilling problems can be adjusting drilling fluid properties by adding nanoparticles. Drilling mud with nanoparticles can physically plug nanosized pores in shale formations and thus reduce the shale permeability, which results in reducing the pressure transmission and improving wellbore stability. Furthermore, the drilling fluid with nanoparticles, creates a very thin, low permeability filter cake resulting in the reduction of the filtrate penetration into the shale. This thin filter cake implies high potential for reducing the differential pressure sticking. In addition, borehole problems such as too high drag and torque can be reduced by adding nanoparticles to drilling fluids. This paper presents the results of laboratory examination of the influence of commercially available nanoparticles of SiO2 (dry SiO2 and water-based dispersion of 30 wt% of silica), and TiO2 (water-based dispersion of 40 wt% of titania) in concentrations of 0.5 wt% and 1 wt% on the properties of water-based fluids. Special emphasis is put on the determination of lubricating properties of the water-based drilling fluids. Nanoparticles added to the base mud without any lubricant do not improve its lubricity performance, regardless of their concentrations and type. However, by adding 0.5 wt% SiO2-disp to the base mud with lubricant, its lubricity coefficient is reduced by 4.6%, and by adding 1 wt% TiO2-disp to the base mud with lubricant, its lubricity coefficient is reduced by 14.3%.

Sign in / Sign up

Export Citation Format

Share Document