scholarly journals Experimental verification of the isotropy postulate at deformation of steel 45 along orthogonal curvilinear trajectories of constant curvature

2021 ◽  
pp. 86-94
Author(s):  
Вадим Иванович Гультяев ◽  
Андрей Алексеевич Алексеев ◽  
Иван Александрович Саврасов ◽  
Валерий Владимирович Гараников
Keyword(s):  
Experimental Data ◽  
Constant Curvature ◽  
Testing Machine ◽  
Experimental Studies ◽  
Machine Loading ◽  
Combined Action ◽  
Thin Walled ◽  
Strain Space ◽  
Complex Trajectories ◽  
Tubular Specimens

Представлены результаты экспериментальных исследований по проверке достоверности одного из основных законов пластичности - постулата изотропии А.А. Ильюшина в условиях ортогональных сложных нагружений по криволинейным окружным траекториям постоянной кривизны. Экспериментальные исследования выполнены на тонкостенных трубчатых образцах из материала сталь 45 на автоматизированном расчетно-экспериментальном комплексе СН-ЭВМ. Программы нагружения трубчатых образцов задавались в девиаторном пространстве деформаций А.А. Ильюшина при одновременном комбинированном действии на образец растяжения-сжатия и кручения. В экспериментах реализовано четыре траектории деформирования, представляющие собой окружности, начинающиеся из начала координат. Установлено, что для реализованных сложных траекторий постоянной кривизны постулат изотропии выполняется как по скалярным, так и векторным свойствам. The results of experimental studies on validation Ilyushin’s isotropy postulate under the conditions of orthogonal complex loads along curvilinear trajectories of constant curvature. Experimental studies were carried out on thin-walled tubular specimens made of steel 45 on SN-EVM testing machine. Loading programs for tubular specimens were set in the deviatorial strain space of A.A. Ilyushin under the combined action of tension-compression and torsion on the specimens. Experimental data are obtained for four strain trajectories, which are circles starting from the origin. It is found that for the realized complex trajectories of constant curvature the isotropy postulate is fulfilled in terms of scalar and vector properties.

Strength and Deformation of Combined Beams with Side Reinforced Plates

2019 ◽  
Vol 968 ◽  
pp. 234-239
Author(s):  
Talyat Azizov ◽  
Oleksii Melnik ◽  
Oleksandr Myza
Keyword(s):  
Experimental Data ◽  
Reinforced Concrete ◽  
Experimental Studies ◽  
Calculated Data ◽  
Concrete Plate ◽  
Combined Action ◽  
Strength And Deformation ◽  
Concrete Plates ◽  
Good Agreement

The results of experimental studies of combined beams consisting of a stone part, reinforced with side reinforced concrete plates are given. Experimentally shown the viability of the proposed structures. The conditions for ensuring the combined action of a stone beam and a reinforced concrete plate are given. Cases are shown when one-sided plates can be used and when double-sided reinforced concrete plates can be used. A comparison of experimental data with the data calculated by the authors developed methods is given. A good agreement between theoretical and calculated data is shown.

scholarly journals Experimental investigation of steel 45 along some smooth curvilinear strain trajectory

2021 ◽  
pp. 33-41
Author(s):  
Вадим Иванович Гультяев ◽  
Владимир Георгиевич Зубчанинов ◽  
Андрей Алексеевич Алексеев ◽  
Иван Александрович Саврасов
Keyword(s):  
Experimental Data ◽  
Experimental Investigation ◽  
Material Properties ◽  
Tubular Specimen ◽  
Experimental Complex ◽  
Oscillatory Character ◽  
Combined Action ◽  
Strain Trajectory ◽  
Thin Walled ◽  
Rigid Loading

В работе представлены экспериментальные результаты деформирования тонкостенного трубчатого образца по гладкой криволинейной траектории деформирования постоянной кривизны, в которой на каждом участке изменяется знак кривизны и смещается ее центр. Экспериментальное исследование выполнено на автоматизированном расчетноэкспериментальном комплексе СН-ЭВМ в девиаторном пространстве деформаций А.А. Ильюшина (жесткое нагружение) при одновременном комбинированном действии на тонкостенный трубчатый образец растяжения-сжатия и кручения. Исследованы скалярные и векторные свойства материала стать 45. Показано, что экспериментальные диаграммы, характеризующие скалярные и векторные свойства материала носят колебательный характер. The paper presents experimental results of deformation of a thin-walled tubular specimen along a smooth curvilinear strain trajectory of constant curvature, in which the sign of curvature changes at each section and its center shifts. Experimental data were obtained on the automated calculation-experimental complex SN-Computer in the deviator space of deformations A.A. Ilyushin (rigid loading) with a simultaneous combined action on the specimen of tensioncompression and torsion. Scalar and vector material properties of steel 45 are investigated. It is shown that experimental diagrams characterizing scalar and vector properties of the material have oscillatory character.

Upgrading of the recording system of complex loading testing machine

2021 ◽  
Vol 87 (2) ◽  
pp. 65-71
Author(s):  
V. A. Galiaskarov ◽  
F. F. Adilov ◽  
R. A. Abirov
Keyword(s):  
Tensile Force ◽  
Testing Machine ◽  
Experimental Studies ◽  
Complex Loading ◽  
Recording System ◽  
Electric Signal ◽  
Structural Elements ◽  
Axial Tensile ◽  
Properties Of Materials ◽  
Tubular Specimens

The effectiveness of experimental studies of the mechanical properties of materials and the reliability of the results obtained are determined by the technical level of testing machines. The stress-strain state of the object is monitored using recording sensors. The reading accuracy for the existing CL unit is 8%. However, this accuracy appeared insufficient when studying the developed plastic deformations. The problem of insufficient accuracy is partially related to the outdated recording system of the experimental setup, both when taking the results of the experiments and when managing the experiment. Getting of the reliable data upon complex loading is necessary to identify the reserves of the bearing capacity of structural elements in conditions of multi-parameter loading. All the experiments on a CL testing machine were carried out at room temperature. An additional amplifier of the electric signal of the strain gauge sensor was introduced to improve the accuracy of the readings of the recording system. The results of modernizing the recording system of the CL testing machine intended for static isothermal tests of tubular specimens are presented. The testing machine provides testing of the samples under axial tensile force and torque.

Diagnostics of metal samples using the results of experimental and theoretical study of positively charged microparticles formed upon sample destruction

2018 ◽  
Vol 84 (10) ◽  
pp. 23-28
Author(s):  
D. A. Golentsov ◽  
A. G. Gulin ◽  
Vladimir A. Likhter ◽  
K. E. Ulybyshev
Keyword(s):  
Experimental Data ◽  
Early Stage ◽  
Experimental Studies ◽  
Material Model ◽  
Total Charge ◽  
Cross Sectional ◽  
Practical Applications ◽  
Mechanical And Electrical Properties ◽  
Order Of Magnitude ◽  
Using Data

Destruction of bodies is accompanied by formation of both large and microscopic fragments. Numerous experiments on the rupture of different samples show that those fragments carry a positive electric charge. his phenomenon is of interest from the viewpoint of its potential application to contactless diagnostics of the early stage of destruction of the elements in various technical devices. However, the lack of understanding the nature of this phenomenon restricts the possibility of its practical applications. Experimental studies were carried out using an apparatus that allowed direct measurements of the total charge of the microparticles formed upon sample rupture and determination of their size and quantity. The results of rupture tests of duralumin and electrical steel showed that the size of microparticles is several tens of microns, the particle charge per particle is on the order of 10–14 C, and their amount can be estimated as the ratio of the cross-sectional area of the sample at the point of discontinuity to the square of the microparticle size. A model of charge formation on the microparticles is developed proceeding from the experimental data and current concept of the electron gas in metals. The model makes it possible to determine the charge of the microparticle using data on the particle size and mechanical and electrical properties of the material. Model estimates of the total charge of particles show order-of-magnitude agreement with the experimental data.

An investigation of effects of level density models and gamma ray strength functions on cross-section calculations for the production of 90Y, 153Sm, 169Er, 177Lu and 186Re therapeutic radioisotopes via (n,γ) reactions

2019 ◽  
Vol 108 (1) ◽  
pp. 11-17
Author(s):  
Mert Şekerci ◽  
Hasan Özdoğan ◽  
Abdullah Kaplan
Keyword(s):  
Experimental Data ◽  
Cross Section ◽  
Production Cross Section ◽  
Gamma Ray ◽  
Production Cross ◽  
Level Density ◽  
Experimental Studies ◽  
Level Density Models ◽  
Strength Functions ◽  
Cancer Diseases

Abstract One of the methods used to treat different cancer diseases is the employment of therapeutic radioisotopes. Therefore, many clinical, theoretical and experimental studies are being carried out on those radioisotopes. In this study, the effects of level density models and gamma ray strength functions on the theoretical production cross-section calculations for the therapeutic radioisotopes 90Y, 153Sm, 169Er, 177Lu and 186Re in the (n,γ) route have been investigated. TALYS 1.9 code has been used by employing different level density models and gamma ray strength functions. The theoretically obtained data were compared with the experimental data taken from the literature. The results are presented graphically for better interpretation.

Microemulsion Phase Behavior Observations, Thermodynamic Essentials, Mathematical Simulation

1981 ◽  
Vol 21 (06) ◽  
pp. 747-762 ◽  
Author(s):  
Karl E. Bennett ◽  
Craig H.K. Phelps ◽  
H. Ted Davis ◽  
L.E. Scriven
Keyword(s):  
Experimental Data ◽  
Phase Behavior ◽  
Experimental Studies ◽  
Mathematical Framework ◽  
Alkyl Aryl Sulfonate ◽  
Phase Volume ◽  
Displacement Efficiency ◽  
Alkyl Aryl ◽  
Theoretical Understanding ◽  
Tie Lines

Abstract The phase behavior of microemulsions of brine, hydrocarbon, alcohol, and a pure alkyl aryl sulfonate-sodium 4-(1-heptylnonyl) benzenesulfonate (SHBS or Texas 1) was investigated as a function of the concentration of salt (NaCl, MgCl2, or CaCl2), the hydrocarbon (n-alkanes, octane to hexadecane), the alcohol (butyl and amyl isomers), the concentration of surfactant, and temperature. The phase behavior mimics that of similar systems with the commercial surfactant Witco TRS 10–80. The phase volumes follow published trends, though with exceptions.A mathematical framework is presented for modeling phase behavior in a manner consistent with the thermodynamically required critical tie lines and plait point progressions from the critical endpoints. Hand's scheme for modeling binodals and Pope and Nelson's approach to modeling the evolution of the surfactant-rich third phase are extended to satisfy these requirements.An examination of model-generated progressions of ternary phase diagrams enhances understanding of the experimental data and reveals correlations of relative phase volumes (volume uptakes) with location of the mixing point (overall composition) relative to the height of the three-phase region and the locations of the critical tie lines (critical endpoints and conjugate phases). The correlations account, on thermodynamic grounds, for cases in which the surfactant is present in more than one phase or the phase volumes change discontinuously, both cases being observed in the experimental study. Introduction The phase behavior of a surfactant-based micellar formulation is one of the major factors governing the displacement efficiency of any chemical flooding process employing that formulation. Knowledge of phase behavior is, thus, important for the interpretation of laboratory core floods, the design of flooding processes, and the evaluation of field tests. Phase behavior is connected intimately with other determinants of the flooding process, such as interfacial tension and viscosity. Since the number of equilibrium phases and their volumes and appearances are easier to measure and observe than phase compositions, viscosities, and interfacial tensions, there is great interest in understanding the phase-volume/phase-property relationships. Commercial surfactants, such as Witco TRS 10-80, are sulfonates of crude or partially refined oil. While they seem to be the most economically practicable surfactants for micellar flooding, their behavior, particularly with crude oils and reservoir brines, can be difficult to interpret, the phases varying with time and from batch to batch. Phase behavior studies with a small number of components, in conjunction with a theoretical understanding of phase behavior progressions, can aid in understanding more complex behavior. In particular, one can begin to appreciate which seemingly abnormal experimental observations (e.g., surfactant present in more than one phase or a discontinuity in phase volume trends) are merely features of certain regions of any phase diagram and which are peculiar to the specific crude oil or commercial surfactant used in the study.We report here experimental studies of the phase behavior of microemulsions of a pure sulfonate surfactant (Texas 1), a single normal alkane hydrocarbon, a simple brine, and a small amount of a suitable alcohol as cosurfactant or cosolvent. The controlled variables are hydrocarbon chain length, alcohol, salinity, salt type (NaCl, MgCl2, or CaCl2), surfactant purity, surfactant concentration, and temperature. Many of these experimental data were presented earlier. SPEJ P. 747^

Hybrid Analysis of Gas Annular Seals With Energy Equation

2013 ◽  
Author(s):  
Patrick J. Migliorini ◽  
Alexandrina Untaroiu ◽  
William C. Witt ◽  
Neal R. Morgan ◽  
Houston G. Wood
Keyword(s):  
Experimental Data ◽  
Hybrid Method ◽  
Energy Equation ◽  
Flow Analysis ◽  
Experimental Studies ◽  
Rotor System ◽  
Bulk Flow ◽  
Outlet Temperature ◽  
Cfd Analysis ◽  
Annular Seals

Annular seals are used in turbomachinery to reduce secondary flow between regions of high and low pressure. In a vibrating rotor system, the non-axisymmetric pressure field developed in the small clearance between the rotor and the seal generate reactionary forces that can affect the stability of the entire rotor system. Traditionally, two analyses have been used to study the fluid flow in seals, bulk-flow analysis and computational fluid dynamics (CFD). Bulk-flow methods are computational inexpensive, but solve simplified equations that rely on empirically derived coefficients and are moderately accurate. CFD analyses generally provide more accurate results than bulk-flow codes, but solution time can vary between days and weeks. For gas damper seals, these analyses have been developed with the assumption that the flow can be treated as isothermal. Some experimental studies show that the difference between the inlet and outlet temperature temperatures is less than 5% but initial CFD studies show that there can be a significant temperature change which can have an effect on the density field. Thus, a comprehensive analysis requires the solution of an energy equation. Recently, a new hybrid method that employs a CFD analysis for the base state, unperturbed flow and a bulk-flow analysis for the first order, perturbed flow has been developed. This method has shown to compare well with full CFD analysis and experimental data while being computationally efficient. In this study, the previously developed hybrid method is extended to include the effects of non-isothermal flow. The hybrid method with energy equation is then compared with the isothermal hybrid method and experimental data for several test cases of hole-pattern seals and the importance of the use of energy equation is studied.

Effect of Boundary Layer Suction on Aerodynamic Performance of High-Turning Compressor Cascade

2013 ◽  
Author(s):  
Longxin Zhang ◽  
Shaowen Chen ◽  
Hao Xu ◽  
Jun Ding ◽  
Songtao Wang
Keyword(s):  
Experimental Data ◽  
Boundary Layer ◽  
Experimental Studies ◽  
Aerodynamic Performance ◽  
Parameter Distribution ◽  
Compressor Cascade ◽  
Boundary Layer Suction ◽  
End Wall ◽  
Low Speed Wind Tunnel ◽  
Good Agreement

Compared with suction slots, suction holes are (1) flexible in distribution; (2) alterable in size; (3) easy to fabricate and (4) high in strength. In this paper, the numerical and experimental studies for a high turning compressor cascade with suction air removed by using suction holes in the end-wall at a low Mach numbers are carried out. The main objective of the investigation is to study the influence of different suction distributions on the aerodynamic performance of the compressor cascade and to find a better compound suction scheme. A numerical model was first made and validated by comparing with the experimental results. The computed flow visualization and exit parameter distribution showed a good agreement with experimental data. Second, the model was then used to simulate the influence of different suction distributions on the aerodynamic performance of the compressor cascade. A better compound suction scheme was obtained by summarizing numerical results and tested in a low speed wind tunnel. As a result, the compound suction scheme can be used to significantly improve the performance of the compressor cascade because the corner separation gets further suppressed.

Photobiological safety of lamps and lamp systems in agriculture

2021 ◽  
Vol 1 (106) ◽  
pp. 34-41
Author(s):  
A. Semenov ◽  
T. Sakhno ◽  
Y. Sakhno
Keyword(s):  
Experimental Data ◽  
Design Methodology ◽  
Risk Group ◽  
Experimental Studies ◽  
Safety Measures ◽  
Safety Requirements ◽  
Labor Safety ◽  
Uv Lamps ◽  
Practical Implications ◽  
Additional Safety

Purpose: The article aims to study the photobiological safety of ultraviolet radiation of UV lamps in agriculture. Design/methodology/approach: The research and analysis of the lighting characteristics of samples of LUF 80 and LE 30 lamps, which are the most widely used in the agrarian complex. Findings: Experimental studies have shown that the photobiological safety of LUF 80 lamps belongs to the low-risk group RG1, while LE 30 lamps show high risk and are thus assigned to group RG3. Research limitations/implications: It is advisable to continue studying the characteristics of lamps and lamp systems for various fields of agriculture on the market in Ukraine to assess their compliance with safety requirements. Practical implications: The application of the proposed approach allows increasing the level of labor safety in commercial greenhouses or any other industry by choosing the suitable lamps for agriculture that at present are not regulated by additional safety measures. Originality/value: The originality of the article is showing the results of the experimental data of the studies of light-technical characteristics of ultraviolet lamps for agriculture.

Research of the Mechanical Properties of the Filament from the Percentage of Filling when Prototyping Machine Parts

2021 ◽  
Vol 410 ◽  
pp. 617-623
Author(s):  
Elena N. Gryadynova ◽  
Andrey V. Gorin ◽  
Alexey Yu. Rodichev
Keyword(s):  
Tensile Strength ◽  
Tensile Testing ◽  
Testing Machine ◽  
Experimental Studies ◽  
Relative Deformation ◽  
Strain Diagram ◽  
Experimental Sample ◽  
Tensile Testing Machine ◽  
Machine Parts ◽  
Fisher’S Criterion

The article contains the analysis of thermoplastics used in prototyping machine parts. We used several types of experimental samples with different filling percentages. The equipment on which the experimental studies were carried out is shown. During the experiment, a specialized tensile testing machine was used. The experimental samples were installed in the developed centering device. Normal conditions were observed during the tests. The results of an experimental tensile study of PLA-plastic specimens are presented. The typical stress-strain diagram of an experimental sample is described, which describes the dependence of stress on relative deformation. An equation of the linear dependence of the tensile strength on the percentage of filament filling has been compiled, which makes it possible to determine the tensile strength of the product at any percentage of the filling of the plastic filament. The assessment is adequately verified by Fisher's criterion. Recommendations for filament filling in prototyping machine parts are given.

Sign in / Sign up

Export Citation Format

Share Document