Design Study of Small Pb-Bi Cooled Non-Refueling Nuclear Power Reactors (SPINNORs)

2012 ◽  
Vol 260-261 ◽  
pp. 296-301 ◽  
Author(s):  
Zaki Su’ud
Keyword(s):  
Nuclear Power ◽  
Internal Conversion ◽  
Volume Fraction ◽  
Reactor Core ◽  
Fissile Material ◽  
Reactor Operation ◽  
Reactivity Effect ◽  
Material Loss ◽  
Coolant Loss ◽  
Fast Neutron Spectrum

Small Pb-Bi Cooled Non-refueling Nuclear Power Reactors(SPINNORs) are small lead-bismuth cooled nuclear power reactors with fast neutron spectrum that could be operated for 20 years without on-site refuelling. In this study the results of neutronic design for 62.5-250MWt NPPs are discussed. The reactor cores are designed to have near zero (less then one effective delayed neutron fraction) burn-up reactivity swing during the burn-up period to avoid a possibility of super-prompt critical accident. The basic concept is that the reactor core is adjusted so that its internal conversion ratio is nearly one. During the reactor operation fissile material accumulates in this central region, which helps to compensate fissile material loss in the peripheral core region and also contributes to negative coolant loss reactivity effect. In general higher fuel volume fraction is needed for smaller core.

Void Reactivity Effect Research on Liquid Metal Cooled Fast Reactor

2017 ◽  
Author(s):  
Yang Lyu ◽  
Xiao Liang
Keyword(s):  
Liquid Metal ◽  
Power Systems ◽  
Fast Reactor ◽  
Nuclear Power ◽  
Reactor Core ◽  
Nuclear Industry ◽  
Fourth Generation ◽  
Reactivity Effect ◽  
The Core ◽  
Reactivity Coefficient

In the fourth generation of advanced nuclear power systems, the liquid metal cooled fast reactor plays a more and more important role, such as SFR, LFR and ADS system with LBE coolant. Void reactivity effect means bubbles produced in the core area will induce the change of reactivity. And this reactivity will affect the safety of the reactor. Through investigation and comparison of several liquid metal cooled fast reactors in the nuclear industry, this paper studies bubbles in different positions and partial voiding of the active zone inside the core and fuel assemblies with Monte Carlo core physics calculation method and then concludes the main influencing factors of void reactivity coefficient. The results can provide reference for the follow-up research and development of new type liquid metal fast reactor core design.

scholarly journals A Compact Gas-Cooled Fast Reactor with an Ultra-Long Fuel Cycle

2013 ◽  
Vol 2013 ◽  
pp. 1-10 ◽  
Author(s):  
Hangbok Choi ◽  
Robert W. Schleicher ◽  
Puja Gupta
Keyword(s):  
Fast Reactor ◽  
Nuclear Power ◽  
Fuel Cycle ◽  
Matrix Material ◽  
Reactor Core ◽  
Operation Time ◽  
Fuel Load ◽  
Fissile Material ◽  
Reactor Physics

In an attempt to allow nuclear power to reach its full economic potential, General Atomics is developing the Energy Multiplier Module (EM2), which is a compact gas-cooled fast reactor (GFR). The EM2augments its fissile fuel load with fertile materials to enhance an ultra-long fuel cycle based on a “convert-and-burn” core design which converts fertile material to fissile fuel and burns it in situ over a 30-year core life without fuel supplementation or shuffling. A series of reactor physics trade studies were conducted and a baseline core was developed under the specific physics design requirements of the long-life small reactor. The EM2core performance was assessed for operation time, fuel burnup, excess reactivity, peak power density, uranium utilization, etc., and it was confirmed that an ultra-long fuel cycle core is feasible if the conversion is enough to produce fissile material and maintain criticality, the amount of matrix material is minimized not to soften the neutron spectrum, and the reactor core size is optimized to minimize the neutron loss. This study has shown the feasibility, from the reactor physics standpoint, of a compact GFR that can meet the objectives of ultra-long fuel cycle, factory-fabrication, and excellent fuel utilization.

scholarly journals Online Simulation of Nuclear Power Plant Primary Systems

2020 ◽  
Vol 2020 ◽  
pp. 1-9
Author(s):  
Hongyun Xie ◽  
Haixia Gu ◽  
Chao Lu ◽  
Jialin Ping
Keyword(s):  
Information System ◽  
Power Plant ◽  
Nuclear Power Plant ◽  
Real Time ◽  
Nuclear Power ◽  
Measurement Data ◽  
Reactor Core ◽  
Power Industry ◽  
Nuclear Power Industry ◽  
Online Simulation

Real-time Simulation (RTS) has long been used in the nuclear power industry for operator training and engineering purposes. And, online simulation (OLS) is based on RTS and with connection to the plant information system to acquire the measurement data in real time for calibrating the simulation models and following plant operation, for the purpose of analyzing plant events and providing indicative signs of malfunctioning. OLS has been applied in certain industries to improve safety and efficiency. However, it is new to the nuclear power industry. A research project was initiated to implement OLS to assist operators in certain critical nuclear power plant (NPP) operations to avoid faulty conditions. OLS models were developed to simulate the reactor core physics and reactor/steam generator thermal hydraulics in real time, with boundary conditions acquired from plant information system, synchronized in real time. The OLS models then were running in parallel with recorded plant events to validate the models, and the results are presented.

Flow and Temperature Fields Measurement Inside Rod Bundle by the Combined Use of PIV and LIF Technique

2018 ◽  
Author(s):  
Xing Li ◽  
Sichao Tan ◽  
Zhengpeng Mi ◽  
Peiyao Qi ◽  
Yunlong Huang
Keyword(s):  
Nuclear Power ◽  
Power Plants ◽  
Great Influence ◽  
Reactor Core ◽  
Transfer Characteristic ◽  
Index Of Refraction ◽  
Temperature Fields ◽  
Spacer Grid ◽  
Rod Bundle ◽  
Combined Use

Thermal hydraulic research of reactor core is important in nuclear energy applications, the flow and heat transfer characteristics of coolant in reactor fuel assembly has a great influence on the performance and safety of nuclear power plants. Particle image velocimetry (PIV) and Laser induced fluorescence (LIF) are the instantaneous, non-intrusive, whole-field fluid mechanics measuring method. In this study, the simultaneous measurement of flow field and temperature field for a rod bundle was conducted using PIV and LIF technique. A facility system, utilizing the matching index of refraction approach, has been designed and constructed for the measurement of velocity and temperature in the rod bundle. In order for further study on complex heat and mass transfer characteristic of rod bundle, the single-phase experiments on the heating conditions are performed. One of unique characteristics of the velocity and temperature distribution downstream the spacer grid was obtained. The experimental results show that the combined use of PIV and LIF technique is applied to the measurement of multi-physical field in a rod bundle is feasible, the measuring characteristics of non-intrusive ensured accuracy of whole field data. The whole field experimental data obtained in rod bundle benefits the design of spacer grid geometry.

scholarly journals Comparative Study for the Prediction of Cavitating Flow inside a Square-Edged Orifice using Different Commercial CFD Software

2019 ◽  
Vol 128 ◽  
pp. 06003
Author(s):  
Gong-Hee Lee ◽  
June-Ho Bae
Keyword(s):  
Structural Damage ◽  
Nuclear Power ◽  
Cavitating Flow ◽  
Regulatory Body ◽  
Reactor Operation ◽  
Flow Acceleration ◽  
Service Testing ◽  
Ansys Cfx ◽  
Rapid Flow ◽  
Computational Fluid Dynamics Cfd

Nuclear power plant operators conduct in-service testing (IST) to verify the safety functions of safety–related pumps and valves and to monitor the degree of vulnerability over time during reactor operation. The system to which the pump and valve to be tested are installed has various sizes of orificesfor flow control and decompression. Rapid flow acceleration and accompanying pressure drop may cause cavitation inside the orifice, which may result in orifice degradation and structural damage. Though licensing applications supported by using Computational Fluid Dynamics (CFD) software are gradually increasing for IST–related problems, there is no CFD software which obtains a licensing from the domestic regulatory body until now. In this paper, to assess the prediction performance of different commercialCFD software for the analysis of cavitating flow inside a square–edged orifice, the simulation was conducted with ANSYS CFX and FLUENT R18.1. The results predicted were then compared with the measured data.

scholarly journals Simulation of MASPn Experiments in MISTRA Test Facility with COCOSYS Code

2008 ◽  
Vol 2008 ◽  
pp. 1-7 ◽  
Author(s):  
Mantas Povilaitis ◽  
Egidijus Urbonavičius
Keyword(s):  
Boundary Conditions ◽  
Nuclear Power ◽  
Power Plants ◽  
Volume Fraction ◽  
Characteristic Length ◽  
Initial Conditions ◽  
Test Facility ◽  
Work Package ◽  
Acceptable Agreement

An issue of the stratified atmospheres in the containments of nuclear power plants is still unresolved; different experiments are performed in the test facilities like TOSQAN and MISTRA. MASPn experiments belong to the spray benchmark, initiated in the containment atmosphere mixing work package of the SARNET network. The benchmark consisted of MASP0, MASP1 and MASP2 experiments. Only the measured depressurisation rates during MASPn were available for the comparison with calculations. When the analysis was performed, the boundary conditions were not clearly defined therefore most of the attention was concentrated on MASP0 simulation in order to develop the nodalisation scheme and define the initial and boundary conditions. After achieving acceptable agreement with measured depressurisation rate, simulations of MASP1 and MASP2 experiments were performed to check the influence of sprays. The paper presents developed nodalisation scheme of MISTRA for the COCOSYS code and the results of analyses. In the performed analyses, several parameters were considered: initial conditions, loss coefficient of the junctions, initial gradients of temperature and steam volume fraction, and characteristic length of structures. Parametric analysis shows that in the simulation the heat losses through the external walls behind the lower condenser installed in the MISTRA facility determine the long-term depressurisation rate.

Expectations for Inservice Testing Programs at New Nuclear Power Plants

2017 ◽  
Author(s):  
Thomas G. Scarbrough
Keyword(s):  
Nuclear Power ◽  
Power Plants ◽  
Nuclear Power Plants ◽  
Reactor Core ◽  
Nuclear Regulatory Commission ◽  
Lessons Learned ◽  
Mechanical Equipment ◽  
American Society ◽  
Regulatory Commission ◽  
Safety Systems

In a series of Commission papers, the U.S. Nuclear Regulatory Commission (NRC) described its policy for inservice testing (IST) programs to be developed and implemented at nuclear power plants licensed under 10 CFR Part 52. This paper discusses the expectations for IST programs based on those Commission policy papers as applied in the NRC staff review of combined license (COL) applications for new reactors. For example, the design and qualification of pumps, valves, and dynamic restraints through implementation of American Society of Mechanical Engineers (ASME) Standard QME-1-2007, “Qualification of Active Mechanical Equipment Used in Nuclear Power Plants,” as accepted in NRC Regulatory Guide (RG) 1.100 (Revision 3), “Seismic Qualification of Electrical and Active Mechanical Equipment and Functional Qualification of Active Mechanical Equipment for Nuclear Power Plants,” will enable IST activities to assess the operational readiness of those components to perform their intended functions. ASME has updated the Operation and Maintenance of Nuclear Power Plants (OM Code) to improve the IST provisions for pumps, valves, and dynamic restraints that are incorporated by reference in the NRC regulations with applicable conditions. In addition, lessons learned from performance experience and testing of motor-operated valves (MOVs) will be implemented as part of the IST programs together with application of those lessons learned to other power-operated valves (POVs). Licensee programs for the Regulatory Treatment of Non-Safety Systems (RTNSS) will be implemented for components in active nonsafety-related systems that are the first line of defense in new reactors that rely on passive systems to provide reactor core and containment cooling in the event of a plant transient. This paper also discusses the overlapping testing provisions specified in ASME Standard QME-1-2007; plant-specific inspections, tests, analyses, and acceptance criteria; the applicable ASME OM Code as incorporated by reference in the NRC regulations; specific license conditions; and Initial Test Programs as described in the final safety analysis report and applicable RGs. Paper published with permission.

scholarly journals Reactor Core Conceptual Design for a Scalable Heating Experimental Reactor, LUTHER

2021 ◽  
Vol 2 (2) ◽  
pp. 207-214
Author(s):  
Thinh Truong ◽  
Heikki Suikkanen ◽  
Juhani Hyvärinen
Keyword(s):  
Low Temperature ◽  
Conceptual Design ◽  
Nuclear Power ◽  
Water Pressure ◽  
Reactor Core ◽  
Electricity Production ◽  
Design Parameters ◽  
Experimental Reactor ◽  
Fuel Assemblies ◽  
Enriched Uranium

In this paper, the conceptual design and a preliminary study of the LUT Heating Experimental Reactor (LUTHER) for 2 MWth power are presented. Additionally, commercially sized designs for 24 MWth and 120 MWth powers are briefly discussed. LUTHER is a scalable light-water pressure-channel reactor designed to operate at low temperature, low pressure, and low core power density. The LUTHER core utilizes low enriched uranium (LEU) to produce low-temperature output, targeting the district heating demand in Finland. Nuclear power needs to contribute to the decarbonizing of the heating and cooling sector, which is a much more significant greenhouse gas emitter than electricity production in the Nordic countries. The main principle in the development of LUTHER is to simplify the core design and safety systems, which, along with using commercially available reactor components, would lead to lower fabrication costs and enhanced safety. LUTHER also features a unique design with movable individual fuel assembly for reactivity control and burnup compensation. Two-dimensional (2D) and three-dimensional (3D) fuel assemblies and reactor cores are modeled with the Serpent Monte Carlo reactor physics code. Different reactor design parameters and safety configurations are explored and assessed. The preliminary results show an optimal basic core design, a good neutronic performance, and the feasibility of controlling reactivity by moving fuel assemblies.

The analysis of emergency situations related to fires at nuclear power plants

2021 ◽  
Vol 30 (5) ◽  
pp. 66-75
Author(s):  
S. A. Titov ◽  
N. M. Barbin ◽  
A. M. Kobelev
Keyword(s):  
Nuclear Power ◽  
Power Plants ◽  
Nuclear Power Plants ◽  
Nuclear Reactor ◽  
Reactor Core ◽  
Emergency Situations ◽  
The Usa ◽  
Large Fires ◽  
Short Circuits ◽  
Nuclear Reactor Core

Introduction. The article provides a system and statistical analysis of emergency situations associated with fires at nuclear power plants (NPPs) in various countries of the world for the period from 1955 to 2019. The countries, where fires occurred at nuclear power plants, were identified (the USA, Great Britain, Switzerland, the USSR, Germany, Spain, Japan, Russia, India and France). Facilities, exposed to fires, are identified; causes of fires are indicated. The types of reactors where accidents and incidents, accompanied by large fires, have been determined.The analysis of major emergency situations at nuclear power plants accompanied by large fires. During the period from 1955 to 2019, 27 large fires were registered at nuclear power plants in 10 countries. The largest number of major fires was registered in 1984 (three fires), all of them occurred in the USSR. Most frequently, emergency situations occurred at transformers and cable channels — 40 %, nuclear reactor core — 15 %, reactor turbine — 11 %, reactor vessel — 7 %, steam pipeline systems, cooling towers — 7 %. The main causes of fires were technical malfunctions — 33 %, fires caused by the personnel — 30 %, fires due to short circuits — 18 %, due to natural disasters (natural conditions) — 15 % and unknown reasons — 4 %. A greater number of fires were registered at RBMK — 6, VVER — 5, BWR — 3, and PWR — 3 reactors.Conclusions. Having analyzed accidents, involving large fires at nuclear power plants during the period from 1955 to 2019, we come to the conclusion that the largest number of large fires was registered in the USSR. Nonetheless, to ensure safety at all stages of the life cycle of a nuclear power plant, it is necessary to apply such measures that would prevent the occurrence of severe fires and ensure the protection of personnel and the general public from the effects of a radiation accident.

A High Effective Parallel Method for the Coupling Between Neutronics and Thermal-Hydraulic

2016 ◽  
Author(s):  
Xiaomeng Dong ◽  
Zhijian Zhang ◽  
Zhaofei Tian ◽  
Lei Li ◽  
Guangliang Chen
Keyword(s):  
Power Plant ◽  
Nuclear Power Plant ◽  
Nuclear Power ◽  
Large Scale ◽  
Nuclear Reactor ◽  
Reactor Core ◽  
Decisive Role ◽  
Reactor Power ◽  
Coupling Method ◽  
Outlet Temperature

Multi-physics coupling analysis is one of the most important fields among the analysis of nuclear power plant. The basis of multi-physics coupling is the coupling between neutronics and thermal-hydraulic because it plays a decisive role in the computation of reactor power, outlet temperature of the reactor core and pressure of vessel, which determines the economy and security of the nuclear power plant. This paper develops a coupling method which uses OPENFOAM and the REMARK code. OPENFOAM is a 3-dimension CFD open-source code for thermal-hydraulic, and the REMARK code (produced by GSE Systems) is a real-time simulation multi-group core model for neutronics while it solves diffusion equations. Additionally, a coupled computation using these two codes is new and has not been done. The method is tested and verified using data of the QINSHAN Phase II typical nuclear reactor which will have 16 × 121 elements. The coupled code has been modified to adapt unlimited CPUs after parallelization. With the further development and additional testing, this coupling method has the potential to extend to a more large-scale and accurate computation.

Sign in / Sign up

Export Citation Format

Share Document