Fire Resistance of Four Coniferous Woody Species in Heilongjiang Province

2013 ◽  
Vol 295-298 ◽  
pp. 2287-2293
Author(s):  
Huai Bing Zheng ◽  
Xu Jian Peng ◽  
Min Xia Zhang ◽  
Lin Ju
Keyword(s):  
Moisture Content ◽  
Pinus Sylvestris ◽  
Heat Release ◽  
Heat Release Rate ◽  
Fire Resistance ◽  
Release Rate ◽  
Pinus Koraiensis ◽  
Heilongjiang Province ◽  
Fire Performance ◽  
Picea Koraiensis

On condition that the heat release rate is 50kW•m-2, the volume of a gas velocity is 24 L•s-1, the combustibility of Pinus koraiensis、Pinus sylvestris var. mongolica、Picea koraiensis、Larix gmelinii in Heilongjiang Province were determined systematically through the use of the controlled atmosphere tapered calorimeter. Through the comparative analysis of the heat release rate and the smoke production rate and some orther burning parameters of the barks and the withered leaves, combine the moisture content of barks and withered leaves of each species, evaluate the fire resistance of this four coniferous species. The results shown: the heat release rate, HRR; total heat release, THR; specific extinction area and smoke produce rate are higher in the barks and withered leaves of Picea koraiensis but the fire performance index is low, these instructions that the fireproof performance is worse in Pinus sylvestris var. mongolica; each Picea koraiensis burning indexs of the Larix gmelinii is lower or the lowest, both the smoke production rate, SPR and the heat release rate, HRR are slow, the fire performance index is high. However, its absolute moisture content and relative moisture content is the highest, it’s flammble.So,we conclude its fire-resistance performance is higher, we could choose it as the fire-preventing priority screening tree species; the flammability of Pinus koraiensis and Pinus sylvestris var. mongolica between the above two species. the combustion characteristics of trees is the result of multiple factor joint, The difference between the different research results is resulted in the choice of the indexs, so it’s urgent need to establish a comprehensive and integrated evaluation index system.

Fire performance of continuous glass fibre reinforced polycarbonate composites: The effect of fibre architecture on the fire properties of polycarbonate composites

2018 ◽  
Vol 53 (12) ◽  
pp. 1705-1715 ◽  
Author(s):  
Yousof M Ghazzawi ◽  
Andres F Osorio ◽  
Michael T Heitzmann
Keyword(s):  
Heat Release ◽  
Heat Release Rate ◽  
Release Rate ◽  
Glass Fibre ◽  
Mass Loss Rate ◽  
Fibre Reinforcement ◽  
Fire Performance ◽  
Cone Calorimetry ◽  
Glass Fibre Reinforced ◽  
Fire Properties

The fire performance of polycarbonate resin and the role of glass fibre reinforcement in altering the fire performance was investigated. Three different fibre weaves with comparable surface density, plain, twill, and unidirectional glass fabrics, were used as reinforcements. E-glass fabrics were solution-impregnated with polycarbonate/dichloromethyl, laid up, and compression-moulded to consolidate the glass fibre reinforced polycarbonate composite. Cone calorimetry tests with an incident radiant flux of 35 kW/m2 were used to investigate the fire properties of polycarbonate resin and its composites. Results showed that glass fibre reinforcement improves polycarbonate performance by delaying its ignition, decreasing its heat release rate, and lowering the mass loss rate. The three fibre weave types exhibited similar time to ignition. However, unidirectional fibre had a 35% lower peak heat release rate followed when compared to plain and twill weave fibres.

scholarly journals The effect of intumescent mat on post-fire performance of carbon fibre reinforced composites

2019 ◽  
Vol 37 (3) ◽  
pp. 257-272 ◽  
Author(s):  
Chenkai Zhu ◽  
Jingjing Li ◽  
Mandy Clement ◽  
Xiaosu Yi ◽  
Chris Rudd ◽  
...  
Keyword(s):  
Carbon Fibre ◽  
Heat Release ◽  
Heat Release Rate ◽  
Release Rate ◽  
Reinforced Composites ◽  
Fire Performance ◽  
Total Heat Release ◽  
Reinforced Composite ◽  
Peak Heat Release Rate ◽  
Fibre Reinforced Composites

This study investigated the effect of intumescent mats (M1 and M2) with different compositions on the post-fire performance of carbon fibre reinforced composites. The sandwich structure was designed for composites where M1 (carbon fibre reinforced composite-M1) or M2 (carbon fibre reinforced composite-M2) mats were covered on the composite surface. A significant reduction in the peak heat release rate and total heat release was observed from the cone calorimetric data, and carbon fibre reinforced composite-M1 showed the lowest value of 148 kW/m2 and 29 MJ/m2 for peak heat release rate and total heat release, respectively. In addition, a minor influence on mechanical properties was observed due to the variation of composite thickness and resin volume in the composite. The post-fire properties of composite were characterised, and the M1 mat presented better retention of flexural strength and modulus. The feasibility of two-layer model was confirmed to predict the post-fire performance of composites and reduce the reliance on the large amounts of empirical data.

scholarly journals Different Methods of Dispersing Carbon Nanotubes in Epoxy Resin and Initial Evaluation of the Obtained Nanocomposite as a Matrix of Carbon Fiber Reinforced Laminate in Terms of Vibroacoustic Performance and Flammability

Materials ◽  
2019 ◽  
Vol 12 (18) ◽  
pp. 2998 ◽  
Author(s):  
Giuseppina Barra ◽  
Liberata Guadagno ◽  
Luigi Vertuccio ◽  
Bartolome Simonet ◽  
Bricio Santos ◽  
...  
Keyword(s):  
Carbon Nanotubes ◽  
Carbon Fiber ◽  
Heat Release ◽  
Heat Release Rate ◽  
Release Rate ◽  
Transmission Loss ◽  
Fire Performance ◽  
Ultrasonic Radiation ◽  
Ultrasound Radiation ◽  
Drastic Increase

Different industrial mixing methods and some of their combinations ((1) ultrasound; (2) mechanical stirring; (3) by roller machine; (4) by gears machine; and (5) ultrasound radiation + high stirring) were investigated for incorporating multi-walled carbon nanotubes (MWCNT) into a resin based on an aeronautical epoxy precursor cured with diaminodiphenylsulfone (DDS). The effect of different parameters, ultrasound intensity, number of cycles, type of blade, and gear speed on the nanofiller dispersion were analyzed. The inclusion of the nanofiller in the resin causes a drastic increase in the viscosity, preventing the homogenization of the resin and a drastic increase in temperature in the zones closest to the ultrasound probe. To face these challenges, the application of high-speed agitation simultaneously with the application of ultrasonic radiation was applied. This allowed, on the one hand, a homogeneous dispersion, and on the other hand, an improvement of the dissipation of heat generated by ultrasonic radiation. The most efficient method was a combination of ultrasound radiation assisted by a high stirring method with the calendar, which was used for the preparation of a carbon fiber reinforced panel (CFRP). The manufactured panel was subjected to dynamic and vibroacoustic tests in order to characterize structural damping and sound transmission loss properties. Under both points of view, the new formulation demonstrated an improved efficiency with reference to a standard CFRP equivalent panel. In fact, for this panel, the estimated damping value was well above the average of the typical values representative of the carbon fiber laminates (generally less than 1%), and also a good vibroacoustic performance was detected as the nanotube based panel exhibited a higher sound transmission loss (STL) at low frequencies, in correspondence with the normal mode participation region. The manufactured panel was also characterized in terms of fire performance using a cone calorimeter and the results were compared to those obtained using a commercially available monocomponent RTM6 (Hexcel composites) epoxy aeronautic resin with the same process and the same fabric and lamination. Compared to the traditional RTM6 resin, the panel with the epoxy nanofilled resin exhibits a significant improvement in fire resistance properties both in terms of a delay in the ignition time and in terms of an increase in the thermal resistance of the material. Compared to the traditional panel, made in the same conditions as the RTM6 resin, the time of ignition of the nanotube-based panel increased by 31 seconds while for the same panel, the heat release rate at peak, the average heat release rate, and the total heat release decreased by 21.4%, 48.5%, and 15%, respectively. The improvement of the fire performance was attributed to the formation of a non-intumescent char due to the simultaneous presence of GPOSS and carbon nanotubes.

Synergistic Fire Performance Between Metal or Metal Filled Organic Coatings and Engineering Plastics

1993 ◽  
Vol 11 (5) ◽  
pp. 371-393 ◽  
Author(s):  
Ramazan Benrashid ◽  
Gordon L. Nelson
Keyword(s):  
Heat Release ◽  
Heat Release Rate ◽  
Release Rate ◽  
Epoxy Coating ◽  
Zinc Borate ◽  
Fire Performance ◽  
Epoxy Coatings ◽  
Engineering Plastics ◽  
Release Data ◽  
Smoke Chamber

Metal filled organic and EMI coatings affect the fire performance properties of engineering plastics. Zinc arc spray, zinc/epoxy, and zinc borate/epoxy coatings on modified-polyphenylene oxide (m-PPO) are particu larly effective. The results from non-flaming NBS smoke chamber tests show a dramatic reduction in smoke for zinc and zinc borate coatings, whereas a ZnO coating did not show the same effect. Heat release data (Radiant Panel) for these samples show lower Q values for zinc, zinc borate coatings compared to m-PPO, epoxy coated m-PPO and ZnO epoxy coated m-PPO. The Fs values for zinc and zinc borate coatings are low compared to a m-PPO control and ZnO coated m-PPO. Polycarbonate structural foam sheet was coated with epoxy coatings filled with zinc, zinc borate, or ZnO. NBS Smoke Chamber data in the non-flaming mode for zinc or ZnO coatings do not show an improvement in smoke produc tion, but a zinc borate epoxy coating does have a reductive effect on smoke. Ra diant Panel Q was low for all coated samples compared to a control. Fs values also were low for coated samples. From OSU heat release data the zinc borate/epoxy coating shows a low heat release rate and the zinc/epoxy coating a much delayed heat release rate. Data for smoke (2 min) was low for coated samples compared to a control, but for smoke (peak) only zinc borate demon strated the potential for significant smoke reduction.

scholarly journals Use of the cone calorimeter to detect seasonal differences in selected combustion characteristics of ornamental vegetation

2005 ◽  
Vol 14 (3) ◽  
pp. 321 ◽  
Author(s):  
David R. Weise ◽  
Robert H. White ◽  
Frank C. Beall ◽  
Matt Etlinger
Keyword(s):  
Moisture Content ◽  
Heat Release ◽  
Heat Release Rate ◽  
Release Rate ◽  
Cone Calorimeter ◽  
Mass Loss Rate ◽  
Combustion Characteristics ◽  
Release Rates ◽  
Intermediate Scale ◽  
Time To Ignition

The flammability of living vegetation is influenced by a variety of factors, including moisture content, physical structure and chemical composition. The relative flammability of ornamental vegetation is of interest to homeowners seeking to make their homes ‘fire safe’. The relative importance of the factors influencing fire behaviour characteristics, such as flammability, is unknown. In the present study, oxygen consumption calorimetry was used to obtain selected combustion characteristics of ornamental vegetation. Peak heat release rate, mass loss rate, time to ignition and effective heat of combustion of 100 × 100-mm samples of foliage and small branches were measured using a bench-scale cone calorimeter. Green and oven-dry samples of 10 species were collected and tested seasonally for a period of 1 year. Similar measurements were made on whole shrubs in an intermediate-scale calorimeter. The range of cone calorimeter peak heat release rates for green and oven-dry samples was 1–176 and 49–331 kW m−2, respectively. Moisture content significantly reduced heat release rates and increased time to ignition. Peak heat release rates for Olea europea and Adenostoma fasciculatum were consistently highest over the year of testing; Aloe sp. consistently had the lowest heat release rate. The correlation of peak heat release rates measured by the cone calorimeter and an intermediate-scale calorimeter was statistically significant yet low (0.51). The use of the cone calorimeter as a tool to establish the relative flammability rating for landscape vegetation requires additional investigation.

Thermal Aging Effects on Fire Performance of the Cross-Linked Polyethylene Insulated Cable

2017 ◽  
Vol 898 ◽  
pp. 2399-2404 ◽  
Author(s):  
Jin Mei Li ◽  
Jia Qing Zhang ◽  
Qiang Li ◽  
Zi Dong Guo
Keyword(s):  
Heat Release ◽  
Heat Release Rate ◽  
Release Rate ◽  
Thermal Aging ◽  
Ignition Time ◽  
Fire Performance ◽  
Aging Effects ◽  
Insulation Materials ◽  
Insulation Failure ◽  
Failure Temperature

To evaluate the fire performance of the cable in service, the ignition time, heat release rate and insulation failure parameters of the accelerated thermal aging cable on stimulated fire condition were studied. The results show that, the extended ignition time and decreasing peak of heat release rate of the cable in the early stage of aging are the addictive including the lubricant, plasticizer and anti-oxygen. In the aggravating of thermal aging, labile materials with low heating value will be exhausted, while the thermal stability of insulation sheath material decreases, its corresponding ignition time will start to shorten and initial peak of heat release rate will start to rise. The insulation failure temperature of the cable is related with the decomposition temperature of insulation materials of the cable by heating. In each aging stage, the decomposition temperatures of insulation materials by heating are all lower than the insulation failure temperature of the cable for about 10°C. The reason for the insulation failure of the cable is that the ambient heat , gives rise to the decomposition by heating of internal insulation materials of the cable through sheath materials finally under the thermal transmission effect.

Research on the Combustibility of PI Needle Punched Nonwovens by Cone Calorimeter

2011 ◽  
Vol 332-334 ◽  
pp. 1335-1338
Author(s):  
Shu Gan Li ◽  
Xiao Ning Jiao ◽  
Qing Long Jia
Keyword(s):  
Mass Loss ◽  
Heat Release ◽  
Heat Release Rate ◽  
Fire Resistance ◽  
Release Rate ◽  
Cone Calorimeter ◽  
Ignition Time ◽  
Total Heat ◽  
Total Heat Release ◽  
Resistance Performance

This paper demonstrates the combustibility of PI needle punched nonwovens by Cone Calorimeter. Ignition parameter, heat release parameters, smoke and toxicity parameters and mass loss parameters of the fabric were obtained from it. It was found that ignition time is 38 s; the peak of heat release rate is 65 kW/m2; total heat release is 7 MJ/m2; smoke release rate is 1.5 L/s; smoke factor is 1.3 MW/m2 and mass lose rate is 73.3%. Therefore the results show that PI needle punched nonwovens has excellent fire-resistance performance.

scholarly journals Studies on the flammability of polypropylene/ammonium polyphosphate and montmorillonite by using the cone calorimeter test

2018 ◽  
Vol 16 (1) ◽  
pp. 108-115 ◽  
Author(s):  
A.A. Hanna ◽  
M.A. Nour ◽  
E.R. Souaya ◽  
M.A. sherief ◽  
A.S. Abdelmoaty
Keyword(s):  
Heat Release ◽  
Heat Release Rate ◽  
Release Rate ◽  
Cone Calorimeter ◽  
Acid Treatment ◽  
Ammonium Polyphosphate ◽  
Fire Performance ◽  
Cone Calorimeter Test ◽  
Peak Heat Release Rate

AbstractFire performance of polypropylene (PP) containing different percentages of ammonium polyphosphate (APP) with montmorillonite (Mt) or treated montmorillonite (MtT) was carried out by using the cone calorimeter test (CCT). Different samples from ammonium polyphosphate and montmorillonite were mixed with 90% polypropylene. The characterization of the prepared samples indicates that there is incorporation between the components of the samples. Heat release rate (HRR), peak heat release rate (PHRR), average heat release rate (Av-HRR), and time to ignition (TTI) of the samples were obtained from the cone calorimeter test. Also, the fire performance index (FPI) and the fire growth rate (FIGRA) were calculated. The interpretation of the curves and the parameters results from the cone calorimeter test which indicates that the addition of montmorillonite to APP increases its action as a flame retardant for PP. Moreover, the samples contain acid treatment montmorillonite showed an increase in the efficiency of ammonium polyphosphate when used. This result may be due to an increase in the SiO2 content by acid treatment.

Fire Performance of Nylon Nanocomposites Fabricated by Melt Intercalation

2007 ◽  
Vol 334-335 ◽  
pp. 737-740
Author(s):  
Russel J. Varley ◽  
Andrew M. Groth ◽  
Kok Hoong Leong
Keyword(s):  
Heat Release ◽  
Heat Release Rate ◽  
Release Rate ◽  
Fire Performance ◽  
Fire Retardancy ◽  
Cone Calorimetry ◽  
Char Layer ◽  
Transmission Electron ◽  
Peak Heat Release Rate ◽  
In Fire

This paper presents results of a study carried out to evaluate the effects of an organomodified nanoclay, either on its own or in combination with a polyimide, upon the fire performance of a commercially available nylon. The fire performance, as determined using cone calorimetry showed that up to 40% improvement in the peak heat release rate could be achieved at addition levels of only around 5wt% of nanoclay. The level of improvement was shown to be strongly dependent upon nanoscale dispersion with a more highly exfoliated morphology, as determined using transmission electron microscopy, which showed a greater reduction in the peak heat release rate compared to a more ordered intercalated structure. Investigation of the mechanism of fire retardancy showed that the reduction in the heat release rate is due to the nanoclay reinforcing the char layer which prevented combustible products from entering in to the gaseous phase. Generally, though, the time to ignition is unaffected by nanoclay additions. The addition of the polyimide to the nanoclay reinforced nylon was inconclusive showing little evidence of further improvements in fire performance.

Sign in / Sign up

Export Citation Format

Share Document