Adsorption of As(V) from Aqueous Solution by the Fe(III)-Impregnated Sorbent Prepared from Sugarcane Bagasse and Applicability of Different Adsorption Models

2013 ◽  
Vol 316-317 ◽  
pp. 509-515
Author(s):  
Hua Zhang ◽  
Xue Hong Zhang ◽  
Yi Nian Zhu ◽  
Mei Na Liang ◽  
Rong Rong Lu
Keyword(s):  
Aqueous Solution ◽  
Sugarcane Bagasse ◽  
Freundlich Isotherm ◽  
Isotherm Models ◽  
Order Kinetic ◽  
Adsorption Models ◽  
Adsorption Capacities ◽  
Monolayer Adsorption ◽  
Order Kinetic Model ◽  
Pseudo Second Order

In this study, a Fe(III)-impregnated sorbent was prepared from sugarcane bagasse and FeCl3 solution via carbonization/activation in a muffle furnace at 500 °C for 4h. Batch experiments were carried out to determine the capacity of the Fe(III)-impregnated sorbent to adsorb As(V) from aqueous solution. The dynamical data fitted very well with the pseudo-second-order kinetic model and the calculated adsorption capacities of 4.8263, 5.2219 and 7.1225 mg/g were equal to the actual values of the experiments at temperatures of 20, 25, and 35 °C, respectively. The experimental data were modeled by Langmuir and Freundlich isotherm models. The Langmuir isotherm with R2 values of 0.9926-0.9968 could yield better fits than the Freundlich isotherm, and the adsorption was endothermic, indicating monolayer adsorption of As(V).Freundlich isotherm, and the adsorption was endothermic, indicating monolayer adsorption of As(V).

scholarly journals Effectiveness of beetroot seeds and H3PO4 activated beetroot seeds for the removal of dyes from aqueous solutions

2017 ◽  
Vol 8 (4) ◽  
pp. 522-531
Author(s):  
A. Machrouhi ◽  
M. Farnane ◽  
A. Elhalil ◽  
R. Elmoubarki ◽  
M. Abdennouri ◽  
...  
Keyword(s):  
Phosphoric Acid ◽  
Isotherm Models ◽  
Order Kinetic ◽  
Solution Ph ◽  
Experimental Isotherm ◽  
Adsorbent Dosage ◽  
Adsorption Capacities ◽  
Monolayer Adsorption ◽  
Order Kinetic Model ◽  
Pseudo Second Order

Abstract Raw beetroot seeds (BS) and H3PO4 activated beetroot seeds (H3PO4-BS) were evaluate for their effectiveness in removing methylene blue (MB) and malachite green (MG) from aqueous solution. BS were carbonized at 500°C for 2 h, and then impregnated with phosphoric acid (phosphoric acid to BS ratio of 1.5 g/g). The impregnated BS were activated in a tubular vertical furnace at 450°C for 2 h. Batch sorption experiments were carried out under various parameters, such as solution pH, adsorbent dosage, contact time, initial dyes concentration and temperature. The experimental results show that the dye sorption was influenced by solution pH and it was greater in the basic range. The sorption yield increases with an increase in the adsorbent dosage. The equilibrium uptake was increased with an increase in the initial dye concentration in solution. Adsorption kinetic data conformed more to the pseudo-second-order kinetic model. The experimental isotherm data were evaluated by Langmuir, Freundlich, Toth and Dubinin–Radushkevich isotherm models. The Langmuir maximum monolayer adsorption capacities were 61.11 and 74.37 mg/g for MB, 51.31 and 213.01 mg/g for MG, respectively in the case of BS and H3PO4-BS. The thermodynamic parameters are also evaluated and discussed.

scholarly journals Dye removal from aqueous solution by raw maize corncob and H3PO4 activated maize corncob

2017 ◽  
Vol 8 (2) ◽  
pp. 214-224 ◽  
Author(s):  
M. Farnane ◽  
H. Tounsadi ◽  
A. Machrouhi ◽  
A. Elhalil ◽  
F. Z. Mahjoubi ◽  
...  
Keyword(s):  
Aqueous Solution ◽  
Order Kinetic ◽  
Solution Ph ◽  
Adsorption Performance ◽  
Adsorption Capacities ◽  
Monolayer Adsorption ◽  
Equilibrium Data ◽  
Order Kinetic Model ◽  
Pseudo Second Order ◽  
Best Fit

AbstractThe focus of this study is the investigation of removal ability of methylene blue (MB) and malachite green (MG) dyes from aqueous solution by raw maize corncob (RMC) and H3PO4 activated maize corncob (AMC). Maize corncobs were carbonized at 500 °C for 2 h, and then impregnated at a phosphoric acid to maize corncob ratio of 2.5 g/g. The impregnated maize corncob was activated in a tubular vertical furnace at 450 °C for 2 h. Samples were characterized by different methods. Adsorption experiments were carried out as a function of solution pH, adsorbent dosage, contact time, initial concentration of dyes and the temperature. Experimental results show that the activation of maize corncob boosts four times the adsorption performance for the selected dyes. The adsorption process is very rapid and was pH dependent with high adsorption capacities in the basic range. The kinetic data were fitted with the pseudo-second-order kinetic model. The best fit of equilibrium data was obtained by the Langmuir model with maximum monolayer adsorption capacities of 75.27 and 271.19 mg/g for MB, 76.42 and 313.63 mg/g for MG, respectively, in the case of RMC and AMC. The temperature did not have much influence on the adsorption performance.

Adsorption Characteristics of Phenol in Aqueous Solution by Pinus massoniana Biochar

2013 ◽  
Vol 295-298 ◽  
pp. 1154-1160 ◽  
Author(s):  
Guo Zhi Deng ◽  
Xue Yuan Wang ◽  
Xian Yang Shi ◽  
Qian Qian Hong
Keyword(s):  
Aqueous Solution ◽  
Ph Value ◽  
Pinus Massoniana ◽  
Isotherm Models ◽  
Order Kinetic ◽  
Adsorbent Dosage ◽  
Salt Ions ◽  
Equilibrium Data ◽  
Order Kinetic Model ◽  
Pseudo Second Order

The objective of this paper is to investigate the feasibility of phenol adsorption from aqueous solution by Pinus massoniana biochar. Adsorption conditions, including contact time, initial phenol concentration, adsorbent dosage, strength of salt ions and pH, have been investigated by batch experiments. Equilibrium can be reached in 24 h for phenol from 50 to 250 mg• L-1. The optimum pH value for this kind of biochar is 5.0. The amount of phenol adsorbed per unit decreases with the increase in adsorbent dosage. The existence of salt ions makes negligible influence on the equilibrium adsorption capacity. The experimental data is analyzed by the Freundlich and Langmuir isotherm models. Equilibrium data fits well to the Freundlich model. Adsorption kinetics models are deduced and the pseudo-second-order kinetic model provides a good correlation for the adsorbent process. The results show that the Pinus massoniana biochar can be utilized as an effective adsorption material for the removal of phenol from aqueous solution.

scholarly journals Simultaneous removal of cationic and anionic dyes from aqueous solution by double functional groups modified bagasse

2020 ◽  
Vol 82 (10) ◽  
pp. 2159-2167
Author(s):  
Ru-yi Zhou ◽  
Jun-xia Yu ◽  
Ru-an Chi
Keyword(s):  
Aqueous Solution ◽  
Functional Groups ◽  
Order Kinetic ◽  
Anionic Dyes ◽  
Adsorption Capacities ◽  
Order Kinetic Model ◽  
Pseudo Second Order ◽  
Amine Groups ◽  
Modified Adsorbents ◽  
Zeta Potential Analysis

Abstract Double functional groups modified bagasse (DFMBs), a series of new zwitterionic groups of carboxyl and amine modified adsorbents, were prepared through grafting tetraethylenepentamine (TEPA) onto the pyromellitic dianhydride (PMDA) modified bagasse using the DCC/DMAP method. DFMBs' ability to simultaneously remove basic magenta (BM, cationic dye) and Congo red (CR, anionic dye) from aqueous solution in single and binary dye systems was investigated. FTIR spectra and Zeta potential analysis results showed that PMDA and TEPA were successfully grafted onto the surface of bagasse, and the ratio of the amount of carboxyl groups and amine groups was controlled by the addition of a dosage of TEPA. Adsorption results showed that adsorption capacities of DFMBs for BM decreased while that for CR increased with the increase of the amount of TEPA in both single and binary dye systems, and BM or CR was absorbed on the modified biosorbents was mainly through electrostatic attraction and hydrogen bond. The adsorption for BM and CR could reach equilibrium within 300 min, both processes were fitted well by the pseudo-second-order kinetic model. The cationic and anionic dyes removal experiment in the binary system showed that DMFBs could be chosen as adsorbents to treat wastewater containing different ratios of cationic and anionic dyes.

Biosorption of hexavalent chromium from aqueous solution by polyethyleneimine-modified ultrasonic-assisted acid hydrochar from Sargassum horneri

2020 ◽  
Vol 81 (6) ◽  
pp. 1114-1129 ◽  
Author(s):  
Jun Wang ◽  
Qinglong Xie ◽  
Ao Li ◽  
Xuejun Liu ◽  
Fengwen Yu ◽  
...  
Keyword(s):  
Aqueous Solution ◽  
Photoelectron Spectroscopy ◽  
Batch Adsorption ◽  
Crosslinking Reaction ◽  
Order Kinetic ◽  
Adsorption Capacities ◽  
Initial Ph ◽  
Ultrasonic Assisted ◽  
Order Kinetic Model ◽  
Pseudo Second Order

Abstract In this study, an efficient route to synthesizing polyethyleneimine-modified ultrasonic-assisted acid hydrochar (PEI-USAH) is developed and reported. Ultrasonic irradiation technique was used as surface modification method to shorten the crosslinking reaction for hydrochar and polyethyleneimine (PEI). The PEI-USAH showed an excellent adsorption capacity for Cr(VI) from aqueous solution. The physicochemical properties of this PEI-modified adsorbent were comparatively characterized by Fourier transform infrared spectroscopy, scanning electron microscopy, X-ray photoelectron spectroscopy, Brunauer–Emmett–Teller analysis and CNHS analysis. The effects of contact time, initial pH, and biosorbent dose on adsorption capacities were investigated. The batch adsorption experiments showed that PEI-USAH possessed the maximum adsorption capacities of 94.38 mg/g and 330.84 mg/g for initial Cr(VI) concentration of 100 mg/L and 500 mg/L, respectively. Furthermore, this adsorption process could be fitted to Langmuir adsorption and described by the pseudo second order kinetic model. Based on the above findings, PEI-USAH could be used as a potential adsorbent for removal of Cr(VI) from wastewater.

scholarly journals Kush - A Potential Biosorbent in the removal of Cd (II) and Zn (II) from aqueous solution

2012 ◽  
Vol 27 ◽  
pp. 107-114
Author(s):  
Jagjit Kour ◽  
P. L. Homagai ◽  
M. R. Pokherel ◽  
K. N. Ghimire
Keyword(s):  
Low Cost ◽  
Freundlich Isotherm ◽  
Isotherm Models ◽  
Order Kinetic ◽  
Waste Streams ◽  
Adsorption Capacities ◽  
Optimum Ph ◽  
Equilibrium Data ◽  
Langmuir Isotherm Model ◽  
Pseudo Second Order

The industrial discharge of heavy metals into waters' course is one of the major pollution problems affecting water quality. Therefore, they must be removed prior to their discharge into waste streams. An efficient and low-cost bioadsorbent has been investigated from Desmostachya bipinnata (Kush) by charring with concentrated sulphuric acid and functionalized with dimethylamine.It was characterised by SEM, FTIR and elemental analysis. The effect of pH, initial concentration and contact time of the metal solution was monitered by batch method. The maximum adsorption capacities were determined for Cd and Zn at their optimum pH 6. The equilibrium data were analysed using Langmuir and Freundlich isotherm models. Langmuir isotherm model fitted well and the rate of adsorption followed the pseudo second order kinetic equation.DOI: http://dx.doi.org/10.3126/jncs.v27i1.6669 J. Nepal Chem. Soc., Vol. 27, 2011 107-114  

scholarly journals Phragmites karkaas a Biosorbent for the Removal of Mercury Metal Ions from Aqueous Solution: Effect of Modification

2015 ◽  
Vol 2015 ◽  
pp. 1-12 ◽  
Author(s):  
Muhammad Hamid Raza ◽  
Aqsa Sadiq ◽  
Umar Farooq ◽  
Makshoof Athar ◽  
Tajamal Hussain ◽  
...  
Keyword(s):  
Aqueous Solution ◽  
Metal Ion ◽  
Freundlich Isotherm ◽  
Agitation Speed ◽  
Second Order ◽  
Ion Concentration ◽  
Order Kinetic ◽  
Order Kinetic Model ◽  
Pseudo Second Order ◽  
Phragmites Karka

Batch scale studies for the adsorption potential of novel biosorbentPhragmites karka(Trin), in its natural and treated forms, were performed for removal of mercury ions from aqueous solution. The study was carried out at different parameters to obtain optimum conditions of pH, biosorbent dose, agitation speed, time of contact, temperature, and initial metal ion concentration. To analyze the suitability of the process and maximum amount of metal uptake, Dubinin-Radushkevich (D-R) model, Freundlich isotherm, and Langmuir isotherm were applied. The values ofqmaxfor natural and treated biosorbents were found at 1.79 and 2.27 mg/g, respectively. The optimum values of contact time and agitation speed were found at 50 min and 150 rpm for natural biosorbent whereas 40 min and 100 rpm for treated biosorbent, respectively. The optimum biosorption capacities were observed at pH 4 and temperature 313 K for both naturalP. karkaand treatedP. karka.RLvalues indicate that comparatively treatedP. karkawas more feasible for mercury adsorption compared to naturalP. karka. Both pseudo-first-order and pseudo-second-order kinetic models were applied and it was found that data fit best to the pseudo-second-order kinetic model. Thermodynamic studies indicate that adsorption process was spontaneous, feasible, and endothermic.

Adsorption of azo dyes from aqueous solution by the hybrid MOFs/GO

2016 ◽  
Vol 73 (7) ◽  
pp. 1728-1737 ◽  
Author(s):  
Ling Li ◽  
Zhennan Shi ◽  
Hongyang Zhu ◽  
Wei Hong ◽  
Fengwei Xie ◽  
...  
Keyword(s):  
Aqueous Solution ◽  
Azo Dyes ◽  
Metal Organic Framework ◽  
Freundlich Isotherm ◽  
Order Kinetic ◽  
Sunset Yellow ◽  
Order Kinetic Model ◽  
Metal Organic ◽  
Pseudo Second Order ◽  
The Stability

In this work, a hybrid of chromium(III) terephthalate metal organic framework (MIL-101) and graphene oxide (GO) was synthesized and its performance in the removal of azo dyes (Amaranth, Sunset Yellow, and Carmine) from water was evaluated. The adsorption for azo dyes on MIL-101/GO was compared with that of MIL-101, and it was found that the addition of GO enhanced the stability of MIL-101 in water and increased the adsorption capacity. The maximum adsorption capacities of MIL-101/GO were 111.01 mg g−1 for Amaranth, 81.28 mg g−1 for Sunset Yellow, and 77.61 mg g−1 for Carmine. The adsorption isotherms and kinetics were investigated, showing that the adsorption fits the Freundlich isotherm and the pseudo-second-order kinetic model. The recyclability of MIL-101/GO was shown by the regeneration by acetone. The high adsorption capability and excellent reusability make MIL-101/GO a competent adsorbent for the removal dyes from aqueous solution.

scholarly journals Comparative Study of Ni-Zn LHS and Mg-Al LDH Adsorbents of Navy Blue and Yellow F3G Dye

2018 ◽  
Vol 16 (1) ◽  
pp. 36 ◽  
Author(s):  
Idha Yulia Ikhsani ◽  
Sri Juari Santosa ◽  
Bambang Rusdiarso
Keyword(s):  
Adsorption Capacity ◽  
Freundlich Isotherm ◽  
Second Order ◽  
Isotherm Models ◽  
Disperse Dyes ◽  
Order Kinetic ◽  
Initial Ph ◽  
Isotherm Adsorption ◽  
Order Kinetic Model ◽  
Pseudo Second Order

Adsorption of disperse dyes from wastewater onto Ni-Zn LHS (layered hydroxide salts) and Mg-Al LDH (layered double hydroxides) has been compared in this study. Effects of initial pH solution, contact time and initial dye concentration were investigated. The ability of the adsorbent to be reused was also studied. The results showed that acidic condition was favorable for the adsorption of each dyes onto both adsorbent. The adsorption kinetics was studied using pseudo-first-order, pseudo-second-order and Santosa’s kinetics models. The experimental data fits well with the pseudo-second order kinetic model. The equilibrium adsorption data were analyzed using Langmuir and Freundlich isotherm models. The results showed that adsorption of navy blue onto both adsorbent followed Freundlich isotherm adsorption, while yellow F3G followed Langmuir isotherm adsorption. In the application for the adsorption the wastewater containing dyes, Ni-Zn LHS has a better adsorption capacity of 52.33 mg/g than that of Mg-Al LDH that 30.54 mg/g. Calcination of the adsorbent which has already been used increased the adsorption capacity of Mg-Al LDH to 84.75 mg/g, but decreased the adsorption capacity of the Ni-Zn LHS to 42.65 mg/g.

scholarly journals The effect of alkaline pretreatment on surfactant-modified clinoptilolite for diclofenac adsorption: isotherm, kinetic, and thermodynamic studies

2020 ◽  
Author(s):  
Fateme Poorsharbaf Ghavi ◽  
Fereshteh Raouf ◽  
Ahmad Dadvand Koohi
Keyword(s):  
Ph Effect ◽  
Freundlich Isotherm ◽  
Kinetic Studies ◽  
Isotherm Models ◽  
Order Kinetic ◽  
Thermodynamic Studies ◽  
Order Kinetic Model ◽  
Pseudo Second Order ◽  
Modified Clinoptilolite ◽  
Kinetic And Thermodynamic Studies

Abstract The elimination of diclofenac traces from aqueous environments is important. In this research, the effect of alkaline (NaOH) pretreatment on clinoptilolite before its modification with a surfactant (HDTMA) for diclofenac adsorption under the speculation of the sole presence of diclofenac in the aqueous solution is investigated. The results are compared through isotherm, kinetic, and thermodynamic studies and supplemented by FTIR, SEM, BET, and the zeta potential analyses. The contact time was investigated in a 0–180-min range. The pH effect was studied in a range of 5–10 because of diclofenac dissociation below pH = 5. The effect of the temperature on diclofenac adsorption was also considered by establishing the experiments at 25, 35, and 45 °C. For HDTMA-modified clinoptilolite, Temkin, and for NaOH-HDTMA-modified clinoptilolite, Dubinin–Radushkevich, and Freundlich isotherm models and in both cases, the pseudo-second-order kinetic model fitted the experimental data best. All the enthalpy and the entropy changes were negative, suggesting exothermic adsorption with a decrease in the degree of freedom of diclofenac anions after the adsorption. Furthermore, diclofenac physisorption was confirmed through isotherm and kinetic studies.

Sign in / Sign up

Export Citation Format

Share Document