Effect of Helical Screw Tape Insertion on Heat Transfer and Pressure Drop Characteristics in a Horizontal Concentric Double Tube Heat Exchanger

2014 ◽  
Vol 541-542 ◽  
pp. 622-627
Author(s):  
A.A. Kapse ◽  
P.R. Dongarwar ◽  
R.R. Gawande
Keyword(s):  
Heat Transfer ◽  
Heat Exchanger ◽  
Pressure Drop ◽  
Cold Water ◽  
Hot Water ◽  
Full Length ◽  
Tube Heat Exchanger ◽  
Nusselt Numbers ◽  
Friction Factors ◽  
Plain Tube

In the present work, the effects of insertion of helical screw tape on heat transfer characteristics and pressure drop in a concentric double tube heat exchanger are experimentally investigated. The heat exchanger has the outer (steel) and inner (copper) tube diameters of 50 mm and 25 mm respectively. The helical screw tape of diameter 19 mm is inserted into the inner tube to increase turbulence which helped to increase the heat transfer rate. The hot water was flowed through the inner tube and cold water was flowed in annulus. The helical screw tape was inserted in 1/3rd length and full length of the tube. The experiments are based on Reynolds number at tube inlet, ranging from 10000 to 42855. The experimental results show that the average Nusselt numbers and friction factors are respectively, 1.41 and 2.08 times over the plain tube for 1/3rd length insert and 1.87 and 4.31 times over the plain tube for full length insert. Furthermore, the enhancement ratio of the helical screw tape varies between 1.03 and 1.17, 1.02 and 1.26 for 1/3rd length insert and full length insert, respectively.

Experimental Investigation of Heat Transfer Enhancement by Using Different Number of Fins in Circular Tube

2018 ◽  
Vol 6 (3) ◽  
pp. 1-12
Author(s):  
Kamil Abdul Hussien
Keyword(s):  
Heat Transfer ◽  
Heat Exchanger ◽  
Cold Water ◽  
Finned Tube ◽  
Hot Water ◽  
Copper Tube ◽  
Smooth Tube ◽  
Tube Heat Exchanger ◽  
Mass Flow Rates ◽  
Flow Heat

Abstract-The present work investigates the enhancement of heat transfer by using different number of circular fins (8, 10, 12, 16, and 20) in double tube counter flow heat exchanger experimentally. The fins are made of copper with dimensions 66 mm OD, 22 mm ID and 1 mm thickness. Each fin has three of 14 mm diameter perforations located at 120o from each to another. The fins are fixed on a straight smooth copper tube of 1 m length, 19.9 mm ID and 22.2 mm OD. The tube is inserted inside the insulated PVC tube of 100 mm ID. The cold water is pumped around the finned copper tube, inside the PVC, at mass flow rates range (0.01019 - 0.0219) kg/s. The Reynold's number of hot water ranges (640 - 1921). The experiment results are obtained using six double tube heat exchanger (1 smooth tube and the other 5 are finned one). The results, illustrated that the heat transfer coefficient proportionally with the number of fin. The results also showed that the enhancement ratio of heat transfer for finned tube is higher than for smooth tube with (9.2, 10.2, 11.1, 12.1 13.1) times for number of fins (8, 10, 12, 16 and 20) respectively.

Heat Transfer Enhancement in a Double Pipe Heat Exchanger by Insertion of Propeller-Type Swirl Generators

2010 ◽  
Author(s):  
Khwanchit Wongcharee ◽  
Somsak Pethkool ◽  
Chinaruk Thianpong
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Nusselt Number ◽  
Heat Exchanger ◽  
Friction Factor ◽  
Operating Conditions ◽  
Interval Length ◽  
Tube Heat Exchanger ◽  
Nusselt Numbers ◽  
Plain Tube

This paper describes an experimental study of turbulent convective heat transfer and flow friction characteristics in a double tube heat exchanger equipped with propellers (2 blade-type). The propellers are used as the decaying swirl generators in the inner tube. The experiments were performed using the propellers with four different interval lengths (l = 1D, 2D, 3D and 4D where D is diameter of the inner tube), for the Reynolds number ranging from 5000 to 32,000, using water with temperature of 27°C and 70°C as cold and hot working fluids, respectively. The data of the tube equipped with the propellers are reported together with those of the plain tube, for comparison. The obtained results demonstrate that the heat transfer rate in term of Nusselt number (Nu) and friction factor (f) in the tube with propellers are higher than those in the plain tube at the similar operating conditions. This is due to the chaotic mixing and efficient interruption of thermal boundary layer caused by the propellers. In addition, the Nusselt number and friction factor in the tube fitted with the propellers increase as the interval length decreases. Depending on Reynolds number and interval length, Nusselt numbers and friction factors in the tube fitted with the propellers are augmented to 1.95 to 2.3 times and 5.8 to 13.2 times of those in the plain tube. In addition, the correlations of the Nusselt number (Nu) and the friction factor (f) for tube fitted with the propellers are reported and the performance evaluation to access the real benefits of using the turbulators is also determined.

scholarly journals Thermo-Hydraulic Performance Analysis on the Effects of Truncated Twisted Tape Inserts in a Tube Heat Exchanger

Symmetry ◽  
2020 ◽  
Vol 12 (10) ◽  
pp. 1652
Author(s):  
Mehdi Ghalambaz ◽  
Ramin Mashayekhi ◽  
Hossein Arasteh ◽  
Hafiz Muhammad Ali ◽  
Pouyan Talebizadehsardari ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Nusselt Number ◽  
Heat Exchanger ◽  
Pressure Drop ◽  
Twisted Tape ◽  
Transfer Enhancement ◽  
Tube Heat Exchanger ◽  
Twisted Tapes ◽  
Plain Tube

This paper investigates the convective heat transfer in a heat exchanger equipped with twisted tape elements to examine effects of the twisted tape truncation percentage, pitch value, position and Reynolds number using 3D numerical simulation. A symmetric heat flux is applied around the tube as the studied heat exchanger. Based on the influences in both heat transfer enhancement and pressure drop, the performance evaluation criterion (PEC) is utilized. Inserting twisted tape elements and reducing the pitch value significantly augment the Nusselt number, friction coefficient and PEC number compared to the plain tube. For the best case with a Reynolds number of 1000, the average Nusselt number increases by almost 151%, which is the case of fully fitted twisted tape at a pitch value of L/4. Moreover, increasing the twisted tape truncation percentage reduces both heat transfer and pressure drop. Furthermore, the highest heat transfer rate is achieved when the truncated twisted tape is located at the entrance of the tube. Finally, it is concluded that for P = L, L/2, L/3 and L/4, the optimum cases from the viewpoint of energy conservation are twisted tapes with truncation percentages of 75, 50, 50 and 0%, in which the related PEC numbers at a Reynolds number of 1000 are almost equal to 1.08, 1.24, 1.4 and 1.76, respectively.

scholarly journals Numerical Simulation of Heat Exchanger for Analyzing the Performance of Parallel and Counter Flow

2021 ◽  
Vol 16 ◽  
pp. 145-152
Author(s):  
Farid Ahmed ◽  
Md Minaruzzaman Sumon ◽  
Muhtasim Fuad ◽  
Ravi Gugulothu ◽  
AS Mollah
Keyword(s):  
Numerical Simulation ◽  
Heat Exchanger ◽  
Pressure Drop ◽  
Heat Exchangers ◽  
Cold Water ◽  
Hot Water ◽  
Shell Side ◽  
Counter Flow ◽  
Tube Heat Exchanger ◽  
Shell And Tube

Heat exchangers are almost used in every industry. Among them, shell and tube heat exchangers are covering around 32% of the total heat exchanger. Numerical simulation of the Computational models is playing an important role for the prototypes including the Heat Exchanger Models for the improvement in modeling. In this study, the CFD analysis of parallel and counter flow shell and tube heat exchanger was performed. Following project, looked into the several aspects and these are the temperature, velocity, and pressure drop and turbulence kinetic energy along with the heat exchanger length. Hot water was placed in tube side and cold water was placed in shell side of the heat exchanger. Shell side cold temperature was increasing along the heat exchanger length. On the other side, tube side hot water temperature was decreasing along the tube length. This effect was more significance in counter flow rather than the parallel flow. Velocity was more fluctuating in the shell side due to presence of the baffles. Also following the same reason, pressure drop was higher in the shell side cold water rather than the tube side hot water. To measure the turbulence effect, turbulence kinetic energy was determined. Turbulence was decreasing first part of the shell and tube heat exchanger. But, it was increasing along through the rest part heat exchanger. All these observations and the outcomes are evaluated and then further analyzed

Experimental Investigation of Performance of Spiral Coil in Spiral Tube Heat Exchanger

2014 ◽  
Vol 592-594 ◽  
pp. 1564-1569
Author(s):  
G.N. Deshpande ◽  
Nitin V. Sali
Keyword(s):  
Heat Transfer ◽  
Experimental Investigation ◽  
Heat Exchanger ◽  
Cold Water ◽  
Hot Water ◽  
Spiral Coil ◽  
Spiral Tube ◽  
Tube Heat Exchanger ◽  
Inside Diameter ◽  
Spiral Shape

In the present work of experimental investigation, the heat transfer performance of Spiral Tube Heat Exchanger (STHE) is studied by manufacturing the heat exchanger. STHEs are known as excellent heat exchanger because it is compact in size and having high heat transfer ability. The STHE consists of copper coils in the spiral shape and placed inside the shell which is made of Stainless Steel. The spiral shape coil is made by bending the straight copper tube of 10 mm inside diameter. The heat exchanger uses 3 such spiral coil brazed with straight header tube of 25 mm inside diameter and at a distance of 15mm apart, the number of turn in a spiral coil is four. Pump is used for circulation of water in both circuits. Cold water is circulated through spiral coil which entered at the periphery and comes out from centre; hot water is entered at the bottom centre of shell and comes out from the top of the shell. The inlet temperature range of hot water and cold water is 50 to 80°C and 30 to 48°C. Mass flow rate range of hot water and cold water is from 0.0633 kg/s to 0.0833kg/s and 0.01 kg/s to 0.0833kg/s.

Numerical simulation of the effect of baffle cut and baffle spacing on shell side heat exchanger performance using CFD

2020 ◽  
Vol 0 (0) ◽  
Author(s):  
Swanand Gaikwad ◽  
Ashish Parmar
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Heat Exchanger ◽  
Pressure Drop ◽  
Transfer Coefficient ◽  
Numerical Results ◽  
Shell Side ◽  
Tube Heat Exchanger ◽  
Shell And Tube ◽  
Two Parameters

AbstractHeat exchangers possess a significant role in energy transmission and energy generation in most industries. In this work, a three-dimensional simulation has been carried out of a shell and tube heat exchanger (STHX) consisting of segmental baffles. The investigation involves using the commercial code of ANSYS CFX, which incorporates the modeling, meshing, and usage of the Finite Element Method to yield numerical results. Much work is available in the literature regarding the effect of baffle cut and baffle spacing as two different entities, but some uncertainty pertains when we discuss the combination of these two parameters. This study aims to find an appropriate mix of baffle cut and baffle spacing for the efficient functioning of a shell and tube heat exchanger. Two parameters are tested: the baffle cuts at 30, 35, 40% of the shell-inside diameter, and the baffle spacing’s to fit 6,8,10 baffles within the heat exchanger. The numerical results showed the role of the studied parameters on the shell side heat transfer coefficient and the pressure drop in the shell and tube heat exchanger. The investigation shows an increase in the shell side heat transfer coefficient of 13.13% when going from 6 to 8 baffle configuration and a 23.10% acclivity for the change of six baffles to 10, for a specific baffle cut. Evidence also shows a rise in the pressure drop with an increase in the baffle spacing from the ranges of 44–46.79%, which can be controlled by managing the baffle cut provided.

scholarly journals Thermal Characteristics Analysis on Multi- Heat Pipe Induced Heat Exchanger

2019 ◽  
Vol 9 (2S2) ◽  
pp. 143-147 ◽  
Keyword(s):  
Heat Transfer ◽  
Heat Exchanger ◽  
Heat Pipe ◽  
Mass Flow Rate ◽  
Mass Flow ◽  
Flow Rate ◽  
Cold Water ◽  
Hot Water ◽  
Working Fluid ◽  
Physical Parameters

In this investigation of multi heat pipe induced in heat exchanger shows the developments in heat transfer is to improve the efficiency of heat exchangers. Water is used as a heat transfer fluid and acetone is used as a working fluid. Rotameter is set to measure the flow rate of cold water and hot water. To maintain the parameter as experimental setup. Then set the mass flow rate of hot water as 40 LPH, 60LPH, 80 LPH, 100LPH, 120 LPH and mass flow rate of cold water as 20 LPH, 30 LPH, 40 LPH, 50 LPH, and 60 LPH. Then 40 C, 45 ºC, 50 ºC, 55 C, 60 ºC are the temperatures of hot water at inlet are maintained. To find some various physical parameters of Qc , hc , Re ,, Pr , Rth. The maximum effectiveness of the investigation obtained from condition of Thi 60 C, Tci 32 C and 100 LPH mhi, 60 LPH mci the maximum effectiveness attained as 57.25. Then the mhi as 100 LPH, mci as 60 LPH and Thi at 40 C as 37.6%. It shows the effectiveness get increased about 34.3 to the maximum conditions.

scholarly journals Thermal Analysis of the Effects of Multifaceted Conditions on Performance of Shell-and-Tube Heat Exchanger

2021 ◽  
Vol 6 (1) ◽  
pp. 69-75
Author(s):  
Taiwo O. Oni ◽  
Ayotunde A. Ojo ◽  
Daniel C. Uguru-Okorie ◽  
David O. Akindele
Keyword(s):  
Heat Transfer ◽  
Heat Exchanger ◽  
Parallel Flow ◽  
Hot Water ◽  
Inlet Temperature ◽  
Fiber Glass ◽  
Counter Flow ◽  
Tube Heat Exchanger ◽  
Shell And Tube ◽  
Flow Configurations

A shell-and-tube heat exchanger which was subjected to different flow configurations, viz. counter flow, and parallel flow, was investigated. Each of the flow configurations was operated under two different conditions of the shell, that is, an uninsulated shell and a shell insulated with fiber glass. The hot water inlet temperature of the tube was reduced gradually from 60 oC to 40 oC, and performance evaluation of the heat exchanger was carried out. It was found that for the uninsulated shell, the heat transfer effectiveness for hot water inlet temperature of 60, 55, 50, 45, and 40 oC are 0.243, 0.244, 0.240, 0.240, and 0.247, respectively, for the parallel flow arrangement. For the counter flow arrangement, the heat transfer effectiveness for the uninsulated shell are 2.40, 2.74, 5.00, 4.17, and 2.70%, respectively, higher than those for the parallel flow. The heat exchanger’s heat transfer effectiveness with fiber-glass-insulated shell for the parallel flow condition with tube hot water inlet temperatures of 60, 55, 50, 45, and 40 oC are 0.223, 0.226, 0.220, 0.225, and 0.227, respectively, whereas the counter flow condition has its heat transfer effectiveness increased by 1.28, 1.47, 1.82, 1.11, and 1.18%, respectively, over those of the parallel flow.

Sign in / Sign up

Export Citation Format

Share Document