Finite Element Simulation of Brittle Fracture of Bulletproof Glass System

2014 ◽  
Vol 566 ◽  
pp. 468-473 ◽  
Author(s):  
Yong Ki An ◽  
Byung Yun Joo ◽  
Dong Teak Chung ◽  
Hyung Kang
Keyword(s):  
Brittle Fracture ◽  
Numerical Simulations ◽  
Borosilicate Glass ◽  
Material Model ◽  
Back Surface ◽  
Borosilicate Glasses ◽  
Test Results ◽  
Protective Ability ◽  
Element Simulation ◽  
Dynamic Brittle Fracture

The thickness and weight of a bulletproof glass material can be reduced using strengthened glass possessing current protective abilities. In this study, numerical simulations are used to estimate the protective ability of strengthened borosilicate glass used in bulletproof glass systems. High-velocity impacts and perforation behaviors are well described by a dynamic brittle fracture model. A parametric study of the material model of glass is conducted by comparing test results of individual impacts with corresponding numerical estimations; size of back-surface spall, morphology of perforated surface, and fractured areas are compared. Material parameters of strengthened and nonstrengthened borosilicate glasses are determined. Numerical simulations using a material model with these parameters well describe the overall fracture behavior of bulletproof glass. The main parameters that affect the protective ability are initial compressive yield stress and fracture stress. Furthermore, the protective ability of strengthened borosilicate glass is ~20% better than that of nonstrengthened borosilicate glass.

scholarly journals Theoretical analysis and experimental research on multi-layer elastic damping track structure

2021 ◽  
Vol 13 (2) ◽  
pp. 168781402199497
Author(s):  
Guanghui Xu ◽  
Shengkai Su ◽  
Anbin Wang ◽  
Ruolin Hu
Keyword(s):  
Finite Element ◽  
Analytical Solution ◽  
Finite Element Simulation ◽  
Reaction Force ◽  
Vibration Reduction ◽  
Vertical Direction ◽  
Propagation Path ◽  
Track Structure ◽  
Test Results ◽  
Element Simulation

The increase of axle load and train speed would cause intense wheelrail interactions, and lead to potential vibration related problems in train operation. For the low-frequency vibration reduction of a track system, a multi-layer track structure was proposed and analyzed theoretically and experimentally. Firstly, the analytical solution was derived theoretically, and followed by a parametric analysis to verify the vibration reduction performance. Then, a finite element simulation is carried out to highlight the influence of the tuned slab damper. Finally, the vibration and noise tests are performed to verify the results of the analytical solution and finite element simulation. As the finite element simulation indicates, after installation of the tuned slab damper, the peak reaction force of the foundation can be reduced by 60%, and the peak value of the vertical vibration acceleration would decrease by 50%. The vibration test results show that the insertion losses for the total vibration levels are 13.3 dB in the vertical direction and 21.7 dB in the transverse direction. The noise test results show that the data of each measurement point is smoother and smaller, and the noise in the generating position and propagation path can be reduced by 1.9 dB–5.5 dB.

First Principles Calculations of Stress-Induced Structural Changes of Supercooled Borosilicate Glass

2016 ◽  
Vol 725 ◽  
pp. 399-404
Author(s):  
Kausala Mylvaganam ◽  
Wei Dong Liu ◽  
Liang Chi Zhang
Keyword(s):  
Uniaxial Compression ◽  
Borosilicate Glass ◽  
Structural Changes ◽  
Mass Density ◽  
Glass Network ◽  
Borosilicate Glasses ◽  
First Principles Calculations ◽  
Sodium Borosilicate Glass ◽  
Compression Direction ◽  
Network Form

Unlike the traditional silicate glasses, borosilicate glasses behave differently because of the addition of boron atoms. Extensive studies have been carried out to understand the abnormal function of boron in glass network. However, it is not clear how the atomic structure of borosilicate glass changes under loading. This paper investigates the behaviour of borosilicate glass under uniaxial compression with the aid of ab initio simulations. Sodium borosilicate glass having 160 atoms and a mass density of 2.51 g/cm3 with composition 3Na2O-B2O3-6SiO2 were equilibrated first at 3500K, then at 2500K, 1500K, 1200K, 1000K, 825K and 625K. Structural analysis showed that at higher temperatures the sodium borosilicate liquid does not have a specific structure. At around 825 K (i.e. around Tg), boron network and silicon network form and remain stable even at a temperature of 625 K. When the supercooled sample at 825K was subjected to uniaxial compression, the stress along the compression direction first increases and then decreases with a change in boron structure, which could modify the behaviour of the borosilicate glass.

scholarly journals Tribological, biocompatibility, and antibiofilm properties of tungsten–germanium coating using magnetron sputtering

2021 ◽  
Vol 32 (1) ◽  
Author(s):  
Mustafa Şükrü Kurt ◽  
Mehmet Enes Arslan ◽  
Ayşenur Yazici ◽  
İlkan Mudu ◽  
Elif Arslan
Keyword(s):  
Cell Culture ◽  
Magnetron Sputtering ◽  
Cell Line ◽  
Borosilicate Glass ◽  
Chromosomal Abnormalities ◽  
Dermal Fibroblast ◽  
Fibroblast Cell ◽  
Antibiofilm Activity ◽  
Borosilicate Glasses

AbstractIn this study, borosilicate glass and 316 L stainless steel were coated with germanium (Ge) and tungsten (W) metals using the Magnetron Sputtering System. Surface structural, mechanical, and tribological properties of uncoated and coated samples were examined using SEM, X-ray diffraction (XRD), energy-dispersive spectroscopy, and tribometer. The XRD results showed that WGe2 chemical compound observed in (110) crystalline phase and exhibited a dense structure. According to the tribological analyses, the adhesion strength of the coated deposition on 316 L was obtained 32.8 N, and the mean coefficient of friction was around 0.3. Biocompatibility studies of coated metallic biomaterials were analyzed on fibroblast cell culture (Primary Dermal Fibroblast; Normal, Human, Adult (HDFa)) in vitro. Hoescht 33258 fluorescent staining was performed to investigate the cellular density and chromosomal abnormalities of the HDFa cell line on the borosilicate glasses coated with germanium–tungsten (W–Ge). Cell viabilities of HDFa cell line on each surface (W–Ge coated borosilicate glass, uncoated borosilicate glass, and cell culture plate surface) were analyzed by using (3-(4,5-Dimethylthiazol-2-yl)-2,5-diphenyltetrazolium bromide) cytotoxicity assay. The antibiofilm activity of W–Ge coated borosilicate glass showed a significant reduction effect on Staphylococcus aureus (ATCC 25923) and Pseudomonas aeruginosa (ATCC 27853) adherence compared to control groups. In the light of findings, tungsten and germanium, which are some of the most common industrial materials, were investigated as biocompatible and antimicrobial surface coatings and recommended as bio-implant materials for the first time.

Confirming the continuum theory of dynamic brittle fracture for fast cracks

Nature ◽  
10.1038/16891 ◽  
1999 ◽  
Vol 397 (6717) ◽  
pp. 333-335 ◽  
Author(s):  
Eran Sharon ◽  
Jay Fineberg
Keyword(s):  
Brittle Fracture ◽  
Continuum Theory ◽  
Dynamic Brittle Fracture ◽  
The Continuum

Virtual Material Model of Joint Interfaces Considering Elastic-Plastic Deformation of Asperities

2013 ◽  
Vol 457-458 ◽  
pp. 257-261
Author(s):  
Li Gang Cai ◽  
Teng Yun Xu ◽  
Yong Sheng Zhao
Keyword(s):  
Plastic Deformation ◽  
Elastic Modulus ◽  
Fractal Theory ◽  
Material Model ◽  
Contact Theory ◽  
Hertz Contact ◽  
Calculation Methods ◽  
Elastic Plastic ◽  
Element Simulation ◽  
Simulation Results

A virtual material model of joint interfaces was established based on the Hertz contact theory and fractal theory, this model was improved by considering the influence of the elastic-plastic deformation of asperities and ameliorating the calculation methods of the elastic modulus. The simulation results of elastic-plastic considered and elastic-plastic unconsidered were compared, moreover, the finite element simulation results and experimental results were compared to fully explain the necessity of considering the influence of the elastic-plastic deformation and the the correctness of the method to calculate the elastic modulus. The research suggested that under a same load the elastic modulus of the model considering the influence of the elastic-plastic deformation was slightly larger than the un considering one, which means it could describe the characteristics of joint interfaces more accurately.

scholarly journals A Useful Manufacturing Guide for Rotary Piercing Seamless Pipe by ALE Method

2020 ◽  
Vol 8 (10) ◽  
pp. 756
Author(s):  
Ameen Topa ◽  
Burak Can Cerik ◽  
Do Kyun Kim
Keyword(s):  
Numerical Simulations ◽  
Maximum Stress ◽  
Three Dimensional ◽  
Material Model ◽  
Manufacturing Processes ◽  
Arbitrary Lagrangian Eulerian ◽  
Analysis Method ◽  
Seamless Pipe ◽  
Ale Formulation ◽  
Good Agreement

The development of numerical simulations is potentially useful in predicting the most suitable manufacturing processes and ultimately improving product quality. Seamless pipes are manufactured by a rotary piercing process in which round billets (workpiece) are fed between two rolls and pierced by a stationary plug. During this process, the material undergoes severe deformation which renders it impractical to be modelled and analysed with conventional finite element methods. In this paper, three-dimensional numerical simulations of the piercing process are performed with an arbitrary Lagrangian–Eulerian (ALE) formulation in LS-DYNA software. Details about the material model as well as the elements’ formulations are elaborated here, and mesh sensitivity analysis was performed. The results of the numerical simulations are in good agreement with experimental data found in the literature and the validity of the analysis method is confirmed. The effects of varying workpiece velocity, process temperature, and wall thickness on the maximum stress levels of the product material/pipes are investigated by performing simulations of sixty scenarios. Three-dimensional surface plots are generated which can be utilized to predict the maximum stress value at any given combination of the three parameters.

scholarly journals On the recovery of the stress-free configuration of the human cornea

2020 ◽  
Vol 2 (4) ◽  
pp. 11-33
Author(s):  
Anna Pandolfi ◽  
Andrea Montanino
Keyword(s):  
Numerical Simulations ◽  
Inverse Analysis ◽  
Material Model ◽  
Free State ◽  
Human Cornea ◽  
Material Models ◽  
Material Parameters ◽  
Optimal Values ◽  
Stress Free State ◽  
Actual Stress

Purpose: The geometries used to conduct numerical simulations of the biomechanics of the human cornea are reconstructed from images of the physiological configuration of the system, which is not in a stress-free state because of the interaction with the surrounding tissues. If the goal of the simulation is a realistic estimation of the mechanical engagement of the system, it is mandatory to obtain a stress-free configuration to which the external actions can be applied. Methods: Starting from a unique physiological image, the search of the stress-free configuration must be based on methods of inverse analysis. Inverse analysis assumes the knowledge of one or more geometrical configurations and, chosen a material model, obtains the optimal values of the material parameters that provide the numerical configurations closest to the physiological images. Given the multiplicity of available material models, the solution is not unique. Results: Three exemplary material models are used in this study to demonstrate that the obtained, non-unique, stress-free configuration is indeed strongly dependent on both material model and on material parameters. Conclusion: The likeliness of recovering the actual stress-free configuration of the human cornea can be improved by using and comparing two or more imaged configurations of the same cornea.

Experimental characterization of composites to support an orthotropic plasticity material model

2017 ◽  
Vol 52 (14) ◽  
pp. 1847-1872 ◽  
Author(s):  
Bilal Khaled ◽  
Loukham Shyamsunder ◽  
Canio Hoffarth ◽  
Subramaniam D Rajan ◽  
Robert K Goldberg ◽  
...  
Keyword(s):  
Material Model ◽  
Unidirectional Composite ◽  
Deformation Model ◽  
Test Results ◽  
Dynamic Impact ◽  
Test Procedures ◽  
Stress Strain ◽  
Damage And Failure ◽  
Orthotropic Behavior

Test procedures for characterizing the orthotropic behavior of a unidirectional composite at room temperature and quasi-static loading conditions are developed and discussed. The resulting data consisting of 12 stress–strain curves and associated material parameters are used in a newly developed material model—an orthotropic elasto-plastic constitutive model that is driven by tabulated stress–strain curves and other material properties that allow for the elastic and inelastic deformation model to be combined with damage and failure models. A unidirectional composite—T800/F3900, commonly used in the aerospace industry, is used to illustrate how the experimental procedures are developed and used. The generated data are then used to model a dynamic impact test. Results show that the developed framework implemented into a special version of LS-DYNA yields reasonably accurate predictions of the structural behavior.

scholarly journals A Variational Approach and Finite Element Implementation for Swelling of Polymeric Hydrogels Under Geometric Constraints

2010 ◽  
Vol 77 (6) ◽  
Author(s):  
Min Kyoo Kang ◽  
Rui Huang
Keyword(s):  
Finite Element ◽  
Aspect Ratio ◽  
Numerical Simulations ◽  
Variational Approach ◽  
Chemical Potential ◽  
Polymer Network ◽  
Material Model ◽  
Geometric Constraints ◽  
Free Energy Function ◽  
Finite Element Implementation

A hydrogel consists of a cross-linked polymer network and solvent molecules. Depending on its chemical and mechanical environment, the polymer network may undergo enormous volume change. The present work develops a general formulation based on a variational approach, which leads to a set of governing equations coupling mechanical and chemical equilibrium conditions along with proper boundary conditions. A specific material model is employed in a finite element implementation, for which the nonlinear constitutive behavior is derived from a free energy function, with explicit formula for the true stress and tangent modulus at the current state of deformation and chemical potential. Such implementation enables numerical simulations of hydrogels swelling under various constraints. Several examples are presented, with both homogeneous and inhomogeneous swelling deformation. In particular, the effect of geometric constraint is emphasized for the inhomogeneous swelling of surface-attached hydrogel lines of rectangular cross sections, which depends on the width-to-height aspect ratio of the line. The present numerical simulations show that, beyond a critical aspect ratio, creaselike surface instability occurs upon swelling.

scholarly journals Tests on Pretrained Superelastic NiTi Shape Memory Alloy Rods: Towards Application in Self-Centering Link Beams

2018 ◽  
Vol 2018 ◽  
pp. 1-13
Author(s):  
Xian Xu ◽  
Guangming Cheng ◽  
Junhua Zheng
Keyword(s):  
Shape Memory Alloy ◽  
Shape Memory ◽  
Strain Amplitude ◽  
Loading Rate ◽  
Mechanical Performance ◽  
Material Model ◽  
Niti Shape Memory Alloy ◽  
Test Results ◽  
Potential Applications ◽  
Strain Model

Austenitic shape memory alloy has potential applications in self-centering seismic resistant structural systems due to its superelastic response under cyclic tension. Raw austenitic SMA needs proper pretreatments and pretraining to gain a stable superelastic property. In this paper, tests are carried out to investigate the effects of pretraining, pretreatments, loading rate, and strain amplitude on the mechanical performance on austenitic SMA rods with a given size. The tested rods are to be used in a new concept self-centering steel link beam. Customized pretraining scheme and heat treatment are determined through the tests. The effects of loading rate and strain amplitude are investigated. A simplified stress-strain model for the SMA rods oriented to numerical simulations is obtained based on the test results. An example of using the simplified material model in numerical analysis of a self-centering steel link beam is conducted to validate the applicability of the model.

Sign in / Sign up

Export Citation Format

Share Document