An Investigation of a Self-Pressurized Alpha V-Type Stirling Engine Converted Diesel Engine

2014 ◽  
Vol 699 ◽  
pp. 695-701 ◽  
Author(s):  
Mohamad Yusof ◽  
Z.A. Zainal ◽  
N.A. Farid ◽  
M.A. Miskam
Keyword(s):  
Diesel Engine ◽  
Mass Production ◽  
Electrical Power ◽  
Engine Performance ◽  
Stirling Engine ◽  
Liquefied Petroleum Gas ◽  
Brake Thermal Efficiency ◽  
Brake Power ◽  
Shaft Power ◽  
Load Conditions

This study reports the investigation results of 194cc. alpha V-type Stirling engine converted from a four-stroke diesel engine that operated in self-pressurized mode. Tests were conducted with air as the working gas and liquefied petroleum gas (LPG) as the heat source. The engine started operating at 600 °C for hot cylinder temperature and 60 °C for cold cylinder temperature, respectively. At heat input of 1100 J/s, the engine performance was successfully tested at both no load and load conditions. For mechanical shaft power assessment, the engine approximately produced a maximum brake power of 7 W, brake thermal efficiency of 0.6% at 717 rpm speed, 811 °C hot cylinder temperature and 96 °C cold cylinder temperature. For electrical power assessment, the engine was capable of generating a maximum electrical output power of 1.7 We at 657 rpm speed, 855 °C hot cylinder temperature and 98 °C cold cylinder temperature. Despite its low engine performance, the study of alpha V-type Stirling engine is a worthwhile step towards clean and sustainable energy in mass production.

scholarly journals Thermal Performance of Compression Ignition Engine Using High Content Biodiesels: A Comparative Study with Diesel Fuel

2021 ◽  
Vol 13 (14) ◽  
pp. 7688
Author(s):  
Asif Afzal ◽  
Manzoore Elahi M. Soudagar ◽  
Ali Belhocine ◽  
Mohammed Kareemullah ◽  
Nazia Hossain ◽  
...  
Keyword(s):  
Diesel Engine ◽  
Diesel Fuel ◽  
Fatty Acid Content ◽  
Engine Performance ◽  
Waste Cooking Oil ◽  
Gas Temperature ◽  
Compression Ignition Engine ◽  
Brake Thermal Efficiency ◽  
Acid Oil ◽  
Exhaust Gas Temperature

In this study, engine performance on thermal factors for different biodiesels has been studied and compared with diesel fuel. Biodiesels were produced from Pongamia pinnata (PP), Calophyllum inophyllum (CI), waste cooking oil (WCO), and acid oil. Depending on their free fatty acid content, they were subjected to the transesterification process to produce biodiesel. The main characterizations of density, calorific range, cloud, pour, flash and fire point followed by the viscosity of obtained biodiesels were conducted and compared with mineral diesel. The characterization results presented benefits near to standard diesel fuel. Then the proposed diesel engine was analyzed using four blends of higher concentrations of B50, B65, B80, and B100 to better substitute fuel for mineral diesel. For each blend, different biodiesels were compared, and the relative best performance of the biodiesel is concluded. This diesel engine was tested in terms of BSFC (brake-specific fuel consumption), BTE (brake thermal efficiency), and EGT (exhaust gas temperature) calculated with the obtained results. The B50 blend of acid oil provided the highest BTE compared to other biodiesels at all loads while B50 blend of WCO provided the lowest BSFC compared to other biodiesels, and B50 blends of all biodiesels provided a minimum % of the increase in EGT compared to diesel.

Performance Investigation of a Four Stroke Diesel Engine, Using Water-Based Ferrofluid as an Additive

2011 ◽  
Author(s):  
F. Daneshvar ◽  
N. Jahani ◽  
M. B. Shafii
Keyword(s):  
Experimental Study ◽  
Magnetic Nanoparticles ◽  
Diesel Engine ◽  
Diesel Fuel ◽  
Engine Performance ◽  
Brake Specific Fuel Consumption ◽  
Engine Exhaust ◽  
Brake Thermal Efficiency ◽  
Diesel Fuels ◽  
Water Based

In this experimental study, a four stroke diesel engine was conducted to investigate the effect of adding water-based ferrofluid to diesel fuel on engine performance. To our knowledge, Magnetic nanoparticles had not been used before. To this end, emulsified diesel fuels of 0, 0.4, and 0.8 water-based ferrofluid/Diesel ratios by volume were used as fuel. The ferrofluid used in this study was a handmade water-based ferrofluid prepared by the authors. The results show that adding water-based ferrofluid to diesel fuel has a perceptible effect on engine performance, increasing the brake thermal efficiency relatively up to 12%, and decreasing the brake specific fuel consumption relatively up to 11% as compared to diesel fuel. In addition, the results indicate that increasing ferrofluid concentration will magnify the results. Furthermore, it was found that magnetic nanoparticles can be collected at the engine exhaust using magnetic bar.

Design and Development of Surge Tank for NOx Emission Reduction in B20 Biofueled Diesel Engine

2020 ◽  
Vol 12 (5) ◽  
Author(s):  
Jaspreet Hira ◽  
Basant Singh Sikarwar ◽  
Rohit Sharma ◽  
Vikas Kumar ◽  
Prakhar Sharma
Keyword(s):  
Diesel Engine ◽  
Research Work ◽  
Engine Performance ◽  
Nox Emission ◽  
Intake Manifold ◽  
Exhaust Gas ◽  
Gas Temperature ◽  
Surge Tank ◽  
Brake Thermal Efficiency ◽  
Exhaust Gas Temperature

In this research work, a surge tank is developed and utilised in the diesel engine for controlling the NOX emission. This surge tank acts as a damper for fluctuations caused by exhaust gases and also an intercooler in reducing the exhaust gas temperature into the diesel engine intake manifold. With the utilisation of the surge tank, the NOX emission level has been reduced to approximately 50%. The developed surge tank is proved to be effective in maintaining the circulation of water at appropriate temperatures. A trade-off has been established between the engine performance parameters including the brake thermal efficiency, brake specific fuel consumption, exhaust gas temperature and all emission parameters including HC and CO.

The Comparative Trail Research on the Performance of a Diesel Engine Fuelled with Diesel Fuel and Biodiesel/Diesel Blended Fuel

2011 ◽  
Vol 142 ◽  
pp. 103-106
Author(s):  
Wen Ming Cheng ◽  
Hui Xie ◽  
Gang Li
Keyword(s):  
Diesel Engine ◽  
Fuel Consumption ◽  
Diesel Fuel ◽  
Thermal Efficiency ◽  
Specific Fuel Consumption ◽  
Brake Specific Fuel Consumption ◽  
Brake Thermal Efficiency ◽  
Series Of Experiments ◽  
Blended Fuel ◽  
Load Conditions

This paper discusses the brake specific fuel consumption and brake thermal efficiency of a diesel engine using cottonseed biodiesel blended with diesel fuel. A series of experiments were conducted for the various blends under varying load conditions at a speed of 1500 rpm and 2500 rpm and the results were compared with the neat diesel. From the results, it is found that the brake specific fuel consumption of cottonseed biodiesel is slightly higher than that of diesel fuel at different engine loads and speeds, with this increase being higher the higher the percentage of the biodiesel in the blend. And the brake thermal efficiency of cottonseed biodiesel is nearly similar to that of diesel fuel at different engine loads and speeds. From the investigation, it is concluded that cottonseed biodiesl can be directly used in diesel engines without any modifications, at least in small blending ratios.

Experimental Investigations of Porosity, Diameter and Length of Ceramic Diesel Particulate Filter (DPF)

2009 ◽  
Author(s):  
Nishikant V. Deshpande ◽  
Suhas C. Kongre ◽  
Piyush N. Deshpande ◽  
Rajan Singh
Keyword(s):  
Particulate Matter ◽  
Diesel Engine ◽  
Power Plant ◽  
Thermal Efficiency ◽  
Research Work ◽  
Back Pressure ◽  
Diesel Particulate ◽  
Brake Thermal Efficiency ◽  
Particulate Filters ◽  
Brake Power

Diesel engine is the most efficient power plant among all known types of internal combustion engines. The Diesel engine is a major candidate to become the power plant of the future. Environmental benefits of Diesel such as low green house gas emissions are balanced by growing concern with emission of Nitrogen oxide (NOx) and Diesel Particulates (PM). The concern over Diesel particulate has increased in recent year because of health concerns. The objective of this research work is to identify the possibility of development of foam type diesel particulate filters (DPF) with indigenous ceramic materials which are easily available and cheaper. While developing the foam type diesel particulate filters, the main aim is to develop required porous structure for DPF with substantial strength, with low back pressure to minimize loss of engine performance, and with high trapping efficiency to reduce the particulate matter. The objective of this research work is also to investigate the effect of new developed filters without any regeneration arrangement and without any control or monitoring system, on the reduction of dry particulate matter and on the performance of diesel engine in terms of parameters like smoke density, back pressure, brake thermal efficiency and brake power. Use of DPF reduces smoke density with back pressure in acceptable limit. Parameters like brake power loss, increase in brake specific fuel consumption and decrease in brake thermal efficiency are caused by increased engine back pressure created by installation of the DPF system. This power penalty is within permissible limits, but can be further reduced by incorporating a regeneration system.

The effect of butanol isomers on diesel engine performance, emission and combustion characteristics under different load conditions

Fuel ◽  
2020 ◽  
Vol 277 ◽  
pp. 118188 ◽  
Author(s):  
Mingzhang Pan ◽  
Chengzheng Tong ◽  
Weiwei Qian ◽  
Fulu Lu ◽  
Jiwen Yin ◽  
...  
Keyword(s):  
Diesel Engine ◽  
Engine Performance ◽  
Combustion Characteristics ◽  
Load Conditions

scholarly journals Effectiveness of oxygen enriched hydrogen-HHO gas addition on DI diesel engine performance, emission and combustion characteristics

2014 ◽  
Vol 18 (1) ◽  
pp. 259-268 ◽  
Author(s):  
S.R. Premkartikkumar ◽  
K. Annamalai ◽  
A.R. Pradeepkumar
Keyword(s):  
Carbon Dioxide ◽  
Carbon Monoxide ◽  
Diesel Engine ◽  
Engine Performance ◽  
Water Electrolysis ◽  
Combustion Characteristics ◽  
Flow Rates ◽  
Brake Thermal Efficiency ◽  
Unburned Hydrocarbon ◽  
Di Diesel Engine

Nowadays, more researches focus on protecting the environment. Present investigation concern with the effectiveness of Oxygen Enriched hydrogen- HHO gas addition on performance, emission and combustion characteristics of a DI diesel engine. Here the Oxygen Enriched hydrogen-HHO gas was produced by the process of water electrolysis. When potential difference is applied across the anode and cathode electrodes of the electrolyzer, water is transmuted into Oxygen Enriched hydrogen-HHO gas. The produced gas was aspirated into the cylinder along with intake air at the flow rates of 1 lpm and 3.3 lpm. The results show that when Oxygen Enriched hydrogen-HHO gas was inducted, the brake thermal efficiency of the engine increased by 11.06%, Carbon monoxide decreased by 15.38%, Unburned hydrocarbon decreased by 18.18%, Carbon dioxide increased by 6.06%, however, the NOX emission increased by 11.19%.

Investigations on Preheated Palm Oil Methyl Esters in the Diesel Engine

1996 ◽  
Vol 210 (2) ◽  
pp. 131-138 ◽  
Author(s):  
H Masjuki ◽  
M Z Abdulmuin ◽  
H S Sii
Keyword(s):  
Diesel Engine ◽  
Palm Oil ◽  
Methyl Esters ◽  
Engine Performance ◽  
Exhaust Emissions ◽  
High Viscosity ◽  
Major Drawback ◽  
Brake Power ◽  
Atomization Characteristics ◽  
Conventional Diesel Fuel

The major drawback of vegetable oil fuels is their high viscosity. Various conventional approaches to reducing the viscosity of vegetable oils are studied theoretically and experimentally. An attempt to reduce the viscosity of the palm oil methyl esters (POME) by preheating the fuel was performed and a comparison on the basis of its projected chance of leading to ‘diesel-like’ combustion was also carried out with conventional diesel fuel. It was observed that by preheating the POME fuel above the conventional temperature, the engine performance, especially the brake power output and the exhaust emissions characteristics, is improved significantly, approaching diesellike' performance. This is mainly attributed to the fact that as the fuel is preheated the viscosity is reduced close to ordinary diesel (OD) fuel. This will result in improved spray and atomization characteristics. Torque, brake power, specific fuel consumption, exhaust emissions and brake thermal efficiencies were measured and calculated. The potential for improved engine performance and reduction in emissions levels was demonstrated.

scholarly journals Experimental and Dynamic Analysis of a Small-Scale Double-Acting Four-Cylinder α-Type Stirling Engine

2021 ◽  
Vol 13 (15) ◽  
pp. 8442
Author(s):  
Chin-Hsiang Cheng ◽  
Yi-Han Tan ◽  
Tzu-Sung Liu
Keyword(s):  
Numerical Model ◽  
Dynamic Model ◽  
Thermodynamic Model ◽  
Heating Temperature ◽  
Engine Performance ◽  
Transient Behavior ◽  
Stirling Engine ◽  
Small Scale ◽  
Working Zone ◽  
Shaft Power

This research studies the double-acting four-cylinder α-type Stirling engine. A numerical model is developed by combining the thermodynamic model and dynamic model to study the engine performance. The pressure values of the working zone calculated using the thermodynamic model are taken into the dynamic model to calculate the forces acting on the mechanism. Then, the dynamic model further calculates the displacement, velocity, and acceleration of the mechanism link to provide the pistons’ displacements for the thermodynamic model. The model is also validated using experimental data obtained from testing an engine prototype. Under a heating temperature of 1000 K, cooling temperature of 315 K, charged pressure of 10 bar, and loading torque of 0.33 Nm, the engine is capable of achieving a shaft power of 26.0 W at 754 rpm. In addition, the thermal properties and the transient behavior of the engine can be further simulated using the validated numerical model.

Sign in / Sign up

Export Citation Format

Share Document