Study on the Cooling System of the Electronic Equipment in the Cabin of the Stratospheric Airship

2015 ◽  
Vol 752-753 ◽  
pp. 815-819
Author(s):  
Hong Shi ◽  
Yan Long Jiang ◽  
Yu Fei Cai
Keyword(s):  
Cooling System ◽  
Heating System ◽  
Electronic Equipment ◽  
Electrical Heating ◽  
Cold Plate ◽  
Flight Altitude ◽  
Optimum Temperature ◽  
Stratospheric Airship ◽  
Strategic Value ◽  
Working Performance

Nowadays, the strategic value of the stratospheric airship attracts more and more attention of the countries. Based on the analysis of the working performance of the stratospheric airship, a cooling system of the electronic equipment is designed and its performance throughout the flight altitude is investigated. The results show that the single cooling system based on cold plate cannot fulfill the cooling task in the extreme hot day and a parallel cooling system as a bench should be designed .meanwhile, the temperature of the cold plate is gradually decreased and then gradually rose with the altitude. The lowest temperature in the process is-35.95°C which would has effect on the performance of the cold plate. Therefore , electrical heating system and frequency regulating speed ventilator are proposed in the above cooling system which is responsible for the electronic equipment at the optimum temperature .

The Heating System of Agricultural Facilities Using Excess Heat Power Transformers

2020 ◽  
Vol 67 (1) ◽  
pp. 42-47
Author(s):  
Anatoliy I. Sopov ◽  
Aleksandr V. Vinogradov
Keyword(s):  
System Design ◽  
Heat Supply ◽  
Cooling System ◽  
Power Transformer ◽  
Electric Heating ◽  
Heating System ◽  
Power Transformers ◽  
Large Power ◽  
Excess Heat ◽  
Power Centers

In power transformers, energy losses in the form of heat are about 2 percent of their rated power, and in transformers of large power centers reach hundreds of kilowatts. Heat is dissipated into the environment and heats the street air. Therefore, there is a need to consume this thermal energy as a source of heat supply to nearby facilities. (Research purpose) To develop methods and means of using excess heat of power transformers with improvement of their cooling system design. (Materials and methods) The authors applied following methods: analysis, synthesis, comparison, monographic, mathematical and others. They analyzed various methods for consuming excess heat from power transformers. They identified suitable heat supply sources among power transformers and potential heat consumers. The authors studied the reasons for the formation of excess heat in power transformers and found ways to conserve this heat to increase the efficiency of its selection. (Results and discussion) The authors developed an improved power transformer cooling system design to combine the functions of voltage transformation and electric heating. They conducted experiments to verify the effectiveness of decisions made. A feasibility study was carried out on the implementation of the developed system using the example of the TMG-1000/10/0.4 power transformer. (Conclusions) The authors got a new way to use the excess heat of power transformers to heat the AIC facilities. It was determined that the improved design of the power transformer and its cooling system using the developed solutions made it possible to maximize the amount of heat taken off without quality loss of voltage transformation.

Study on Copper Cold Plate Designs for Electronics Liquid Cooling System

2006 ◽  
Author(s):  
Yi. Feng ◽  
Y. Wang ◽  
C. Y. Huang
Keyword(s):  
Heat Transfer ◽  
Thermal Performance ◽  
Cooling System ◽  
Pure Copper ◽  
Cold Plate ◽  
Performance Limits ◽  
Liquid Cooling ◽  
Cold Plates ◽  
Management Approaches ◽  
Liquid Cooling System

The increasing power consumption of microelectronic systems and the dense layout of semiconductor components leave very limited design spaces with tight constraints for the thermal solution. Conventional thermal management approaches, such as extrusion, fold-fin, and heat pipe heat sinks, are somehow reaching their performance limits, due to the geometry constraints. Currently, more studies have been carried out on the liquid cooling technologies, as the flexible tubing connection of liquid cooling system makes both the accommodation in constrained design space and the simultaneous cooling of multi heating sources feasible. To significantly improve the thermal performance of a liquid cooling system, heat exchangers with more liquid-side heat transfer area with acceptable flow pressure drop are expected. This paper focuses on the performance of seven designs of source heat exchanger (cold plate). The presented cold plates are all made in pure copper material using wire cutting, soldering, brazing, or sintering process. Enhanced heat transfer surfaces such as micro channel and cooper mesh are investigated. Detailed experiments have been conducted to understand the performance of these seven cooper cold plates. The same radiators, fan, and water pump were connected with each cooper cold plate to investigate the overall thermal performance of liquid cooling system. Water temperature readings at the inlets and outlets of radiators, pump, and colder plate have been taken to interpret the thermal resistance distribution along the cooling loop.

Exploring the Use of Alumina Nanofluid as Emergency Coolant for Nuclear Fuel Bundle

2018 ◽  
Vol 11 (2) ◽  
Author(s):  
A. S. Chinchole ◽  
Arnab Dasgupta ◽  
P. P. Kulkarni ◽  
D. K. Chandraker ◽  
A. K. Nayak
Keyword(s):  
Heat Transfer ◽  
Nuclear Fuel ◽  
Nuclear Reactor ◽  
Cooling System ◽  
Nuclear Reactors ◽  
Electrical Heating ◽  
High Dose ◽  
Potential Candidate ◽  
Alumina Nanofluid ◽  
Core Cooling

Abstract Nanofluids are suspensions of nanosized particles in any base fluid that show significant enhancement of their heat transfer properties at modest nanoparticle concentrations. Due to enhanced thermal properties at low nanoparticle concentration, it is a potential candidate for utilization in nuclear heat transfer applications. In the last decade, there have been few studies which indicate possible advantages of using nanofluids as a coolant in nuclear reactors during normal as well as accidental conditions. In continuation with these studies, the utilization of nanofluids as a viable candidate for emergency core cooling in nuclear reactors is explored in this paper by carrying out experiments in a scaled facility. The experiments carried out mainly focus on quenching behavior of a simulated nuclear fuel rod bundle by using 1% Alumina nanofluid as a coolant in emergency core cooling system (ECCS). In addition, its performance is compared with water. In the experiments, nuclear decay heat (from 1.5% to 2.6% reactor full power) is simulated through electrical heating. The present experiments show that, from heat transfer point of view, alumina nanofluids have a definite advantage over water as coolant for ECCS. Additionally, to assess the suitability of using nanofluids in reactors, their stability was investigated in radiation field. Our tests showed good stability even after very high dose of radiation, indicating the feasibility of their possible use in nuclear reactor heat transfer systems.

scholarly journals Analysis of the Impact of the Construction of a Trombe Wall on the Thermal Comfort in a Building Located in Wrocław, Poland

Atmosphere ◽  
2019 ◽  
Vol 10 (12) ◽  
pp. 761 ◽  
Author(s):  
Jagoda Błotny ◽  
Magdalena Nemś
Keyword(s):  
Temperature Increase ◽  
Cooling System ◽  
Renewable Energy Sources ◽  
Heating System ◽  
Wall Material ◽  
Ansys Fluent ◽  
Cooling Period ◽  
Heating And Cooling ◽  
Trombe Wall ◽  
The Impact

Changes in climate, which in recent years have become more and more visible all over the world, have forced scientists to think about technologies that use renewable energy sources. This paper proposes a passive solar heating and cooling system, which is a Trombe wall located on the southern facade of a room measuring 4.2 m × 5.2 m × 2.6 m in Wrocław, Poland. The studies were carried out by conducting a series of numerical simulations in the Ansys Fluent 16.0 environment in order to examine the temperature distribution and air circulation in the room for two representative days during the heating and cooling period, i.e., 16 January and 15 August (for a Typical Meteorological Year). A temperature increase of 1.11 °C and a temperature decrease in the morning and afternoon hours of 2.27 °C was obtained. Two options for optimizing the passive heating system were also considered. The first involved the use of triple glazing filled with argon in order to reduce heat losses to the environment, and for this solution, a temperature level that was higher by 8.50 °C next to the storage layer and an increase in the average room temperature by 1.52 °C were achieved. In turn, the second solution involved changing the wall material from concrete to brick, which resulted in a temperature increase of 0.40 °C next to the storage layer.

Personal Heating/Cooling System Using Peltier

2020 ◽  
Author(s):  
Amanie Abdelmessih ◽  
Andre Alvarez ◽  
Joshua Gonzalez ◽  
Timothy Gooch ◽  
Adrian Gutierrez ◽  
...  
Keyword(s):  
Law Enforcement ◽  
Cooling System ◽  
Family Members ◽  
Lithium Ion ◽  
Weather Conditions ◽  
Heating System ◽  
The Elderly ◽  
Hazardous Substances ◽  
Biological Warfare ◽  
Heating And Cooling

Abstract Common quibbles in most homes are the temperature setting. Some family members are comfortable with cooler temperature settings, while other family members prefer warmer temperature settings. Not to mention the fragile elderly and some medical situations require different temperature settings for those individuals than the rest of the occupants of the space. The purpose of this article is to outline a research where we created a working prototype of a portable, effective Peltier cooling/heating system. Peltier, or thermoelectric modules, are devices that use the differences in electric voltages to create a difference in temperature between two flat opposite sides of the thin module. The system can easily be switched between the heating and cooling modes. In contrast to compression refrigeration systems it produces a very low level of noise output. Also, the system is portable, small in size, and light weight. Another advantage of using the Peltier system is it does not employ hazardous substances such as hydrochlorofluorocarbons, but uses water. While a system such as this could be beneficial in the day to day comfort of any individual, it could prove vital to the survival of the elderly and medically vulnerable individuals. This heating/cooling system can enhance the performance of military, particularly in biological warfare suites, and law enforcement personnel who find themselves in less than desirable weather conditions. This uniquely designed Peltier system is compact, and lightweight. Cooling/heating through the system would be achieved by the exchange of heat between the user and a custom designed vest. The system is powered by lithium ion battery pack. Details of this unique design are discussed in the article. Also, the testing and results are reported, and discussed.

scholarly journals Numerical Assessment of Heat Transfer and Entropy Generation of a Porous Metal Heat Sink for Electronic Cooling Applications

Energies ◽  
2020 ◽  
Vol 13 (15) ◽  
pp. 3851
Author(s):  
Hamed Rasam ◽  
Prosun Roy ◽  
Laura Savoldi ◽  
Shabnam Ghahremanian
Keyword(s):  
Heat Transfer ◽  
Temperature Field ◽  
Entropy Generation ◽  
Heat Sink ◽  
Cooling System ◽  
Solid Phase ◽  
Porous Metal ◽  
Electronic Equipment ◽  
Bejan Number ◽  
Pore Density

In the present study, the thermal performance of an electronic equipment cooling system is investigated. The heat sink used in the current cooling system consists of a porous channel with a rectangular cross-section that is assumed to be connected directly to the hot surface of an electronic device. In this modeling, a fully developed flow assumption is used. The Darcy–Brinkman model was used to determine the fluid flow field. Since using the local thermal equilibrium (LTE) model may provide results affected by the error in metal foams, in the present research, an attempt has first been made to examine the validity range of this model. The local thermal non-equilibrium (LTNE) model taking into account the viscous dissipation effect was then used to determine the temperature field. To validate the numerical solution, the computed results were compared with other studies, and an acceptable agreement was observed. Analysis of the temperature field shows that if the fluid–solid-phase thermal conductivity ratio is 1 or the Biot number has a large value, the difference between the temperature of the solid phase and the fluid phase decreases. Moreover, the effect of important hydrodynamic parameters and the porous medium characteristics on the field of hydrodynamic, heat, and entropy generation was studied. Velocity field analysis shows that increasing the pore density and reducing the porosity cause an increase in the shear stress on the walls. By analyzing the entropy generation, it can be found that the irreversibility of heat transfer has a significant contribution to the total irreversibility, leading to a Bejan number close to 1. As a guideline for the design of a porous metal heat sink for electronic equipment, the use of porous media with low porosity reduces the total thermal resistance and improves heat transfer, reducing the total irreversibility and the Bejan number. Moreover, the increasing of pore density increases the specific porous surface; consequently, it reduces the total irreversibility and Bejan number and improves the heat transfer.

scholarly journals Hydrate and Wax Prevention in Flowlines by Electrical Heating

2000 ◽  
Author(s):  
Jens Kristian Lervik ◽  
Harald Kulbotten ◽  
Gunnar Klevjer ◽  
Øyvind Iversen
Keyword(s):  
Power Supply ◽  
Hydrate Formation ◽  
Magnetic Characteristic ◽  
Heating System ◽  
Electrical Heating ◽  
Oil Companies ◽  
Direct Heating ◽  
The North ◽  
Wide Range ◽  
The Difference

Traditional chemical treatment methods have considerable operation costs and represent a risk to the environment. Since 1987 Norwegian oil companies have been investigating alternative electrical heating methods for prevention of hydrate and wax plugs. A joint industry project ‘Concept Verification – Direct Heating of Oil & Gas Pipelines’ was initiated in 1996 and terminated in October 1999. During this work an electrical heating system was proved to be feasible on several fields in the North Sea. It will be installed on 7 flowlines of 13% Chromium (Crl3) with lengths between 6 km and 16 km. Electrical heating is used to maintain or raise the thermally insulated steel pipe temperature above the critical value for hydrate formation (typically 15–25 °C) or wax formation (typically 20–40°C). A single-phase power supply for the heating system is based on commercial components and connected to the platform power supply. The qualification work for the direct heating system has included full scale testing for single and parallel pipes, end termination at the template, bypass of a template and aspects concerning corrosion control. The rating of the system is dependent on the magnetic and electrical characteristics of the steel material. Such data is not commonly available. Measurements performed during the qualification program confirm that the magnetic characteristic may vary within a wide range for a specific steel quality and that mechanical stress and heat treatment can effect the magnetic characteristic. The difference in magnetic characteristic of individual Crl3 pipes results in variation of the pipe temperature and problems concerning differential pressure during melting. The problem can be handled by dividing the pipeline into a number of sections, each with a limited variation of the magnetic characteristic, thus keeping the temperature for the whole pipeline within acceptable limits. As a part of the pipe specification both electrical and magnetic characteristic should be available. These data can be determined by measuring arrangements in the production line of the mill. Measures to limit the variation of magnetic characteristic should be discussed.

Application of Micro-Channel Fin for Cold Plate of Liquid Cooling System and Vapor Chamber

2009 ◽  
Author(s):  
Koichi Mashiko ◽  
Masataka Mochizuki ◽  
Yuji Saito ◽  
Yasuhiro Horiuchi ◽  
Thang Nguyen ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Thermal Resistance ◽  
Thermal Performance ◽  
Cooling System ◽  
Cold Plate ◽  
Micro Channel ◽  
Vapor Chamber ◽  
Liquid Cooling ◽  
Liquid Cooling System ◽  
Heat Spreading

Recently energy saving is most important concept for all electric products and production. Especially, in Data-Center cooling system, power consumption of current air cooling system is increasing. For not only improving thermal performance but also reducing electric power consumption of this system, liquid cooling system has been developed. This paper reports the development of cold plate technology and vapor chamber application by using micro-channel fin. In case of cold plate application, micro-channel fin technology is good for compact space design, high thermal performance, and easy for design and simulation. Another application is the evaporating surface for vapor chamber. The well-known devices for effective heat transfer or heat spreading with the lowest thermal resistance are heat pipes and vapor chamber, which are two-phase heat transfer devices with excellent heat spreading and heat transfer characteristics. Normally, vapor chamber is composed of sintered power wick. Vapor chamber container is mechanically supported by stamped pedestal or wick column or solid column, but the mechanical strength is not enough strong. So far, the application is limited in the area of low strength assembly. Sometime the mechanical supporting frame is design for preventing deformation. In this paper, the testing result of sample is described that thermal resistance between the heat source and the ambient can be improved approximately 0.1°C/W by using the micro-channel vapor chamber. Additionally, authors presented case designs using vapor chamber for cooling computer processors, and proposed ideas of using micro-channel vapor chamber for heat spreading to replace the traditional metal plate heat spreader.

Sign in / Sign up

Export Citation Format

Share Document