Multi Response Optimization of Process Parameters on AA8011 Friction Stir Welded Aluminium Alloys Using RSM Based GRA Coupled with DEA

2015 ◽  
Vol 813-814 ◽  
pp. 446-450 ◽  
Author(s):  
K. Palani ◽  
C. Elanchezhian
Keyword(s):  
Process Parameters ◽  
Tilt Angle ◽  
Feed Rate ◽  
Rotational Speed ◽  
Aluminium Alloys ◽  
Welding Process ◽  
Fusion Welding ◽  
Gray Relational Analysis ◽  
Friction Stir ◽  
Tool Tilt Angle

The friction stir welding process is the newly developed material joining process used to join the different materials which are very difficult to join in the conventional fusion welding process. In this investigation using the specially designed straight cam profiled tool, the multiple responses of Ultimate tensile strength, Ultimate yield strength and Percentage of elongation with the process parameters of rotational speed, tool tilt angle and feed rate are optimized. The five level, three factor rotatable central composite design is selected to optimize the responses of friction stir welded AA 8011 aluminium alloys. The highest gray relational grade with the highest relative efficiency is found using the gray relational analysis coupled with the data envelopment analysis to predict the optimum parameters. It exposes that at the rotational speed of 680 rpm, the tool tilt angle of 98 degrees and the feed rate of 24 mm/min the good weld quality can be attained.

Multiple Performance Characteristics Optimization for AA8011 on Friction Stir Welding by RSM Based DEA

2015 ◽  
Vol 813-814 ◽  
pp. 451-455 ◽  
Author(s):  
K. Palani ◽  
C. Elanchezhian
Keyword(s):  
Tilt Angle ◽  
Feed Rate ◽  
Rotational Speed ◽  
Aluminium Alloys ◽  
Relative Efficiency ◽  
Data Envelopment ◽  
Friction Stir ◽  
Optimum Parameters ◽  
Tool Tilt Angle ◽  
Central Composite

In this investigation, the optimization of the multiple responses of Vickers hardness, Impact strength with notched and Un-notched conditions of the process parameters of rotational speed, tool tilt angle and feed rate with the straight cam profiled tool is considered. The three factors, five level rotatable central composite design are selected to optimize the responses of friction stir welded AA 8011 aluminium alloys. The highest relative efficiency is found using the data envelopment analysis to predict the optimum parameters. It reveals that at the rotational speed of 680 RPM, the tool tilt angle of 85 degrees and the feed rate of 24 mm/min the good weld quality can be achieved.

scholarly journals Influence of Tool Tilt Angle on Material Flow and Defect Generation in Friction Stir Welding of AA2219

2018 ◽  
Vol 68 (5) ◽  
pp. 512-518 ◽  
Author(s):  
Suresh Meshram ◽  
Madhusudhan Reddy
Keyword(s):  
Friction Stir Welding ◽  
Process Parameters ◽  
Tilt Angle ◽  
Material Flow ◽  
Critical Role ◽  
Welding Process ◽  
Fusion Welding ◽  
Friction Stir ◽  
Tool Tilt Angle ◽  
Welding Processes

Heat treatable aluminium alloy AA2219 is widely used for aerospace applications, welded through gas tungsten and gas metal arc welding processes. Welds of AA2219 fabricated using a fusion welding process suffers from poor joint properties or welding defects due to melting and re-solidification. Friction stir welding (FSW) is a solid-state welding process and hence free from any solidification related defects. However, FSW also results in defects which are not related to solidification but due to improper process parameter selection. One of the important process parameters, i.e., tool tilt angle plays a critical role in material flow during FSW, controlling the size and location of the defects. Effect of tool tilt angle on material flow and defects in FSW is ambiguous. A study is therefore taken to understand the role of tool tilt angle on FSW defects. Variation in temperature, forces, and torque generated during FSW as a result of different tool tilt angles was found to be responsible for material flow in the weld, controlling the weld defects. An intermediate tool tilt angle (1o-2o) gives weld without microscopic defect in 7 mm thick AA2219 for a given set of other process parameters. At this tool tilt angle, x-force, and Z- force is balanced with viscosity and the material flow strain rate sufficient for the material to flow and fill internal voids or surface defects in the weld.

Influence of Process Parameters on Microstructure of Friction Stir Processed Mg AZ31 Alloy

2017 ◽  
pp. 1293-1305
Author(s):  
G. Venkateswarlu ◽  
M.J. Davidson ◽  
G.R.N. Tagore ◽  
P. Sammaiah
Keyword(s):  
Plastic Deformation ◽  
Grain Refinement ◽  
Process Parameters ◽  
Tilt Angle ◽  
Friction Stir Processing ◽  
Rotational Speed ◽  
Traverse Speed ◽  
Homogeneous Microstructure ◽  
Friction Stir ◽  
Tool Tilt Angle

Friction stir processing (FSP) has been developed on the principles of friction stir welding (FSW) as an effective and efficien new method for grain refinement and microstructural modification, providing intense plastic deformation as well as higher strain rates than other conventional severe plastic deformation methods. FSP produces an equiaxed homogeneous microstructure consisting of fine grains, resulting in the enhancement of the properties of the material at room temperature. The objective of the present paper is to examine the influence of friction stir processing (FSP) parameters namely tool rotational speed (RS), tool traverse speed (TS) and tool tilt angle (TA) on the microstructures of friction stir processed AZ31B-O magnesium alloy. This investigation has focused on the microstructural changes occurred in the dynamically recrystallised nugget zone/ stir zone and the thermo mechanically affected zone during FSP. The results presented in this work indicate that all the three FSP process parameters have a significant effect on the resulting microstructure and also found that the rotational speed has greatly influenced the homogenization of the material. The grain refinement is higher at intermediate rotational speed (1150 rpm), traverse speed (32 mm / min and tilt angle (10). It is established that FSP can be a good grain refinement method for improving the properties of the material.

scholarly journals Influence of Friction Stir Processing Parameters on Mg ZE 41-SiC Surface Composite

2019 ◽  
Vol 8 (2) ◽  
pp. 6058-6061
Keyword(s):  
Process Parameters ◽  
Tilt Angle ◽  
Friction Stir Processing ◽  
Rotational Speed ◽  
Traverse Speed ◽  
Nano Particles ◽  
Micro Hardness ◽  
Friction Stir ◽  
Surface Composite ◽  
Tool Tilt Angle

In this study, the influence of friction stir processing process parameters (FSP), such as tool rotational speed, tool traverse speed, and the tool tilt angle on the mechanical properties of Sic reinforced surface magnesium rare earth ZE41 alloy composite was studied. The process was carried at tool rotational speeds of 710, 900, 1120, 1600, 1400 and 1800 rpm, tool traverse speeds of 16, 25, 40 and 63 mm/min and tool tilt angle of degree 1. Nano-particles of SiC (40 microns) were used as reinforcements to produce a composite surface. The grain refinement of the processed specimens was analyzed using scanning electron microscope. It is observed from the results that FSP process parameters influenced the surface composite area, SiC particles distribution and micro hardness of the composite. The outcomes indicated that the higher micro hardness was obtained at rotational speed of 1100 RPM, traverse speed 40mm/min and tilt angle 10 .

scholarly journals Shoulder Related Temperature Thresholds in FSSW of Aluminium Alloys

Materials ◽  
2021 ◽  
Vol 14 (16) ◽  
pp. 4375
Author(s):  
David G. Andrade ◽  
Sree Sabari ◽  
Carlos Leitão ◽  
Dulce M. Rodrigues
Keyword(s):  
Heat Generation ◽  
Process Parameters ◽  
Rotational Speed ◽  
Aluminium Alloys ◽  
Spot Welding ◽  
Base Material ◽  
Main Process ◽  
Welding Temperature ◽  
Friction Stir ◽  
Tool Diameter

Friction Stir Spot Welding (FSSW) is assumed as an environment-friendly technique, suitable for the spot welding of several materials. Nevertheless, it is consensual that the temperature control during the process is not feasible, since the exact heat generation mechanisms are still unknown. In current work, the heat generation in FSSW of aluminium alloys, was assessed by producing bead-on-plate spot welds using pinless tools. Coated and uncoated tools, with varied diameters and rotational speeds, were tested. Heat treatable (AA2017, AA6082 and AA7075) and non-heat treatable (AA5083) aluminium alloys were welded to assess any possible influence of the base material properties on heat generation. A parametric analysis enabled to establish a relationship between the process parameters and the heat generation. It was found that for rotational speeds higher than 600 rpm, the main process parameter governing the heat generation is the tool diameter. For each tool diameter, a threshold in the welding temperature was identified, which is independent of the rotational speed and of the aluminium alloy being welded. It is demonstrated that, for aluminium alloys, the temperature in FSSW may be controlled using a suitable combination of rotational speed and tool dimensions. The temperature evolution with process parameters was modelled and the model predictions were found to fit satisfactorily the experimental results.

Procedure to find out the optimal ranges of process parameters for friction stir welding

2021 ◽  
pp. 146442072199314
Author(s):  
Shubham Verma ◽  
Joy Prakash Misra ◽  
Meenu Gupta
Keyword(s):  
Friction Stir Welding ◽  
Process Parameters ◽  
Tilt Angle ◽  
Welding Speed ◽  
Rotational Speed ◽  
Optical Microscope ◽  
Graphical Analysis ◽  
Friction Stir ◽  
Steepest Ascent ◽  
Vertical Milling Machine

The present study deals with the application of sequential procedure (i.e. steepest ascent) to obtain the optimum values of process parameters for conducting friction stir welding (FSW) experiments. A vertical milling machine is modified by fabricating fixture and tool ( H13 material) for performing FSW operation to join AA7039 plates. The steepest ascent technique is employed to design the experiments at different rotational speed, welding speed, and tilt angle. The ultimate tensile strength is considered as a performance characteristic for deciding the optimal levels. The mechanical and metallurgical characteristics of the joints are studied by executing tensile and microhardness tests. It is concluded from the graphical analysis of the steepest ascent technique that the optimal maximum and minimum values are 1812–1325 r/min for rotational speed, 43–26 mm/min for welding speed, and 2°–1.3° for tilt angle, respectively. Besides, optical microscope and scanning electron microscope are utilized for microstructural and fractographic analyses for a better understanding of the process.

Optimization of friction stir welding parameters of dissimilar aluminium alloys 6061 and 5083 by using response surface methodology

2021 ◽  
pp. 095440622110058
Author(s):  
Sanjeev Verma ◽  
Vinod Kumar
Keyword(s):  
Tensile Strength ◽  
Friction Stir Welding ◽  
Tilt Angle ◽  
Feed Rate ◽  
Aluminium Alloys ◽  
Welded Joint ◽  
Welding Parameters ◽  
Friction Stir ◽  
Industrial Sectors ◽  
Tool Pin

Aluminium and its alloys are lightweight, corrosion-resistant, affordable and high-strength material and find wide applications in shipbuilding, automotive, constructions, aerospace and other industrial sectors. In applications like aerospace, marine and automotive industries, there is a need to join components made of different aluminium alloys, viz. AA6061 and AA5083. In this study friction stir welding (FSW) is used to join dissimilar plates made of AA6061-T6 and AA5083-O. The effect of varying tool pin profile, tool rotation speed, tool feed rate and tilt angle of the tool has been investigated on the tensile strength and percentage elongation of the welded joints. Box-Behkan design, with four input parameters and three levels of each parameter has been employed to decide the set of experimental runs. The regression models have been developed to investigate the influence of welding variables on the tensile strength and elongation of the welded joint. It is revealed that with the increase in welding parameters like tool rpm, tool feed rate and tilt angle of the tool, both the mechanical properties increase, reach a maximum level, followed by a decrease with further increase in the value of parameters. Amongst different types of tool pin profiles used, the FSW tool having straight cylindrical (SC) pin profile is found to yield the maximum strength and elongation of the welded joint for different combinations of welding parameters. Multiple response optimization indicates that the maximum UTS (135.83 MPa) and TE (4.35%) are obtained for the welded joint fabricated using FSW tool having SC pin profile, tilted at 1.11° and operating at tool speed and feed rate of 1568 rpm and 39.53 mm/min., respectively.

scholarly journals The Effect of Copper and Brass on Friction Stir Welded Dissimilar Aluminium Alloy When Used as in Thin Sheet Form

2016 ◽  
Vol 45 (2) ◽  
pp. 118-122
Author(s):  
G. Gopala Krishna ◽  
P.Ram Reddy ◽  
M.Manzoor Hussain
Keyword(s):  
Aluminium Alloy ◽  
Aluminium Alloys ◽  
Low Cost ◽  
Thin Sheet ◽  
Welding Process ◽  
Cost Effective ◽  
Tensile Tests ◽  
Fusion Welding ◽  
Friction Stir ◽  
Effect Of Copper

In recent year’s aluminium and aluminium alloys are most widely used in many applications because of light weight, good formability and malleability, corrosion resistance, moderate strength and low cost. Friction Stir Welding (FSW) process is efficient and cost effective method for welding aluminium and aluminium alloys. FSW is a solid state welding process that means the material is not melted during the process. Complete welding process accomplishes below the melting point of materials so it overcomes many welding defects that usually happens with conventional fusion welding technique which were initially used for low melting materials. Though this process is initially developed for low melting materials but now process is widely used for a variety of other materials including titanium, steel and also for composites. The present butt jointed FSW experimental work has been done in two ways. Initially a comparison of tensile properties of friction stir (FS) welded similar aluminium alloy (AA6351 with AA6351) and dissimilar aluminium alloy (AA6351 with AA5083) combinations. Later the effect of impurities (copper and brass) in sheet form (0.1 mm thick) when used as insert in between two dissimilar aluminium alloy (AA6351 with AA5083) plates during FSW. Tensile tests were performed for these combinations and results were compared for with and without using strip material (copper and brass).

scholarly journals Experimental Investigation of Friction Stir Welding on 6061-T6 Aluminum Alloy using Taguchi-Based GRA

Metals ◽  
2020 ◽  
Vol 10 (11) ◽  
pp. 1480
Author(s):  
Assefa Asmare ◽  
Raheem Al-Sabur ◽  
Eyob Messele
Keyword(s):  
Aluminum Alloy ◽  
Friction Stir Welding ◽  
Process Parameters ◽  
Rotational Speed ◽  
Weight Ratio ◽  
Welding Process ◽  
Quality Criteria ◽  
Alloy Sheet ◽  
Friction Stir ◽  
Weld Joints

The use of aluminum alloys, nowadays, is swiftly growing from the prerequisite of producing higher strength to weight ratio. Lightweight components are crucial interest in most manufacturing sectors, especially in transportation, aviation, maritime, automotive, and others. Traditional available joining methods have an adverse effect on joining these lightweight engineering materials, increasing needs for new environmentally friendly joining methods. Hence, friction stir welding (FSW) is introduced. Friction stir welding is a relatively new welding process that can produce high-quality weld joints with a lightweight and low joining cost with no waste. This paper endeavors to deals with optimizing process parameters for quality criteria on tensile and hardness strengths. Samples were taken from a 5 mm 6061-T6 aluminum alloy sheet with butt joint configuration. Controlled process parameters tool profile, rotational speed and transverse speed were utilized. The process parameters are optimized making use of the combination of Grey relation analysis method and L9 orthogonal array. Mechanical properties of the weld joints are examined through tensile, hardness, and liquid penetrant tests at room temperature. From this research, rotational speed and traverse speed become significant parameters at a 99% confidence interval, and the joint efficiency reached 91.3%.

Sign in / Sign up

Export Citation Format

Share Document