Effects of Alkaline Solution on the Properties of Slag Based Geopolymer

2018 ◽  
Vol 877 ◽  
pp. 193-199 ◽  
Author(s):  
Suman Saha ◽  
C. Rajasekaran
Keyword(s):  
Compressive Strength ◽  
Sodium Hydroxide ◽  
Sodium Silicate ◽  
Alkaline Solution ◽  
Sodium Hydroxide Solution ◽  
Setting Time ◽  
Sodium Silicate Solution ◽  
Silicate Solution ◽  
Hydroxide Solution ◽  
Geopolymer Paste

Production of Ordinary Portland Cement (OPC) requires huge quantity of natural resources and energy and it releases large amount of carbon - di - oxide to the environment. Therefore, enormous studies have been carried out throughout the world to establish geopolymer as an alternative binder material for the replacement of OPC to protect the environment. This study intends to explore the effects of alkaline solution on the properties of geopolymer produced with ground granulated blast furnace slag. Properties such as Standard consistency, setting time of slag based geopolymer paste has been determined using Vicat’s apparatus (according to the guidelines given by Indian Standards for OPC). In order to determine the effects of alkaline solution on the properties of geopolymers, the concentration of sodium hydroxide solution has been varied from 6M to 16M and the ratio of sodium silicate solution to sodium hydroxide solution is also varied from 1.0 to 2.0. Results indicate higher standard consistency and significant less setting time for slag based geopolymer paste than that of OPC paste. Compressive strength of the geopolymer paste and mortar cube samples, cured in ambient conditions till the day of testing, is increasing with the increase of the concentration of sodium hydroxide solution. Highest compressive strength is obtained for the samples prepared with alkaline solution having the ratio of sodium silicate solution to sodium hydroxide solution as 1.5. But when the concentration of sodium hydroxide solution is beyond 14M, decreasing trend in compressive strength is observed.

Fabrication and Characterization of Geopolymers from Japanese Volcanic Ashes

2014 ◽  
Vol 92 ◽  
pp. 1-7
Author(s):  
Shinobu Hashimoto ◽  
Hayami Takeda ◽  
Tatsuya Machino ◽  
Haruka Kanie ◽  
Sawao Honda ◽  
...  
Keyword(s):  
Compressive Strength ◽  
Sodium Hydroxide ◽  
Sodium Silicate ◽  
Volcanic Ash ◽  
Sodium Hydroxide Solution ◽  
Water Immersion ◽  
Sodium Silicate Solution ◽  
Silicate Solution ◽  
Hydroxide Solution ◽  
Volcanic Ashes

Geopolymers were fabricated from some Japanese volcanic ashes. 30 g of volcanic ash with 200μm in diameter was mixed with 10 ml of sodium hydroxide solution with various concentrations to form slurry which became geopolymer after curing. When 8.5~11.5 mol/L of sodium hydroxide solution was used, the compressive strength of the resultant geopolymers reached to 25-35MPa. However, when the volcanic ash with high silica content was used, the compressive strength of the geopolymer was under 20 MPa. Furthermore, the addition of sodium silicate hydrate into starting slurry which was consisted of volcanic ash and sodium silicate solution had not effected on the compressive strength of geopolymer. In contrast, the compressive strength of the geopolymer decreased to 30 % of compressive strength compared to that of original geopolymer after water immersion for 3 days. However, crushing treatment of the volcanic ash contributed to retain the compressive strength. Actually, when 10μm of volcanic ash was used to fabricate geopolymer, the compressive strength improved to 70% compared to that of original geopolymer.

scholarly journals Effect of Concentration of Sodium Hydroxide and Degree of Heat Curing on Fly Ash-Based Geopolymer Mortar

2014 ◽  
Vol 2014 ◽  
pp. 1-6 ◽  
Author(s):  
Subhash V. Patankar ◽  
Yuwaraj M. Ghugal ◽  
Sanjay S. Jamkar
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Sodium Hydroxide ◽  
Sodium Hydroxide Solution ◽  
Large Change ◽  
Sodium Silicate Solution ◽  
Silicate Solution ◽  
Test Period ◽  
Hydroxide Solution ◽  
Increase With Increase

Geopolymer concrete/mortar is the new development in the field of building constructions in which cement is totally replaced by pozzolanic material like fly ash and activated by alkaline solution. This paper presented the effect of concentration of sodium hydroxide, temperature, and duration of oven heating on compressive strength of fly ash-based geopolymer mortar. Sodium silicate solution containing Na2O of 16.45%, SiO2 of 34.35%, and H2O of 49.20% and sodium hydroxide solution of 2.91, 5.60, 8.10, 11.01, 13.11, and 15.08. Moles concentrations were used as alkaline activators. Geopolymer mortar mixes were prepared by considering solution-to-fly ash ratio of 0.35, 0.40, and 0.45. The temperature of oven curing was maintained at 40, 60, 90, and 120°C each for a heating period of 24 hours and tested for compressive strength at the age of 3 days as test period after specified degree of heating. Test results show that the workability and compressive strength both increase with increase in concentration of sodium hydroxide solution for all solution-to-fly ash ratios. Degree of heating also plays vital role in accelerating the strength; however there is no large change in compressive strength beyond test period of three days after specified period of oven heating.

Mix Design and Compressive Strength of Geopolymer Concrete Containing Blended Ash from Agro-Industrial Wastes

2011 ◽  
Vol 339 ◽  
pp. 452-457 ◽  
Author(s):  
Mohd Azreen Mohd Ariffin ◽  
Mohd Warid Hussin ◽  
Muhammad Aamer Rafique Bhutta
Keyword(s):  
Compressive Strength ◽  
Sodium Hydroxide ◽  
Sodium Silicate ◽  
Alkaline Solution ◽  
Sodium Hydroxide Solution ◽  
Mix Design ◽  
Geopolymer Concrete ◽  
Palm Oil Fuel Ash ◽  
Hydroxide Solution ◽  
Fuel Ash

Geopolymer concrete is a type of amorphous alumino-silicate cementitious material. Geopolymer can be polymerized by polycondensation reaction of geopolymeric precursor and alkali polysilicates. Compared to conventional cement concrete, the production of geopolymer concrete has a relative higher strength, excellent volume stability and better durability. This paper presents the mix design and compressive strength of geopolymer concrete manufactured from the blend of palm oil fuel ash (POFA) and pulverized fuel ash (PFA) as full replacement of cement with a combination of sodium silicate and sodium hydroxide solution used as alkaline liquid. The density and strength of the geopolymer concrete with various PFA: POFA ratios of 0:100, 30:70, 50:50 and 70:30 together with sodium silicate to sodium hydroxide solution by mass at 2.5 and 1.0, are investigated. The concentrations of alkaline solution used are 14 Molar and 8 Molar. Tests were carried out on 100x100x100 mm cube geopolymer concrete specimens. Specimens were cured at room temperature and heat curing at 60°C and 90°C for 24 hours, respectively. The effects of mass ratios of PFA: POFA, the alkaline solution to PFA: POFA, ratio and concentration of alkaline solution on fresh and hardened properties of concrete are examined. The results revealed that as PFA: POFA mass ratio increased the workability and compressive strength of geopolymer concrete are increased, the ratio and concentration of alkaline solution increased, the compressive strength of geopolymer concrete increases with regards to curing condition.

The Effect of Dry Mix Sodium Hydroxide onto Workability and Compressive Strength of Geopolymer Paste

2020 ◽  
Vol 12 (9) ◽  
Author(s):  
A. Z. Mohd Ali ◽  
◽  
N. A. Jalaluddin ◽  
N. Zulkiflee ◽  
◽  
...  
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Sodium Hydroxide ◽  
Sodium Silicate ◽  
Alkaline Solution ◽  
High Emission ◽  
New Material ◽  
Curing Regime ◽  
Solid Form ◽  
Geopolymer Paste

The production of ordinary Portland cement (OPC) consumes considerable amount of natural resources, energy and at the same time contribute in high emission of CO2 to the atmosphere. A new material replacing cement as binder called geopolymer is alkali-activated concrete which are made from fly ash, sodium silicate and sodium hydroxide (NaOH). The alkaline solution mixed with fly ash producing alternative binder to OPC binder in concrete named geopolymer paste. In the process, NaOH was fully dissolved in water and cooled to room temperature. This study aims to eliminate this process by using NaOH in solid form together with fly ash before sodium silicate liquid and water poured into the mixture. The amount of NaOH solids were based on 10M concentration. The workability test is in accordance to ASTM C230. Fifty cubic mm of the geopolymer paste were prepared which consists of fly ash to alkaline solution ratio of 1: 0.5 and the curing regime of 80℃ for 24 hours with 100% humidity were implemented. From laboratory test, the workability of dry method geopolymer paste were decreased. The compressive strength of the dry mix of NaOH showed 55% and the workability has dropped to 58.4%, it showed strength reduction compared to the wet mix method.

scholarly journals Artificial Intelligence Approaches for Prediction of Compressive Strength of Geopolymer Concrete

Materials ◽  
2019 ◽  
Vol 12 (6) ◽  
pp. 983 ◽  
Author(s):  
Dong Dao ◽  
Hai-Bang Ly ◽  
Son Trinh ◽  
Tien-Thinh Le ◽  
Binh Pham
Keyword(s):  
Artificial Intelligence ◽  
Compressive Strength ◽  
Fly Ash ◽  
Sodium Hydroxide ◽  
Sodium Silicate ◽  
Steel Slag ◽  
Sodium Silicate Solution ◽  
Silicate Solution ◽  
Partial Replacement ◽  
Geopolymer Concrete

Geopolymer concrete (GPC) has been used as a partial replacement of Portland cement concrete (PCC) in various construction applications. In this paper, two artificial intelligence approaches, namely adaptive neuro fuzzy inference (ANFIS) and artificial neural network (ANN), were used to predict the compressive strength of GPC, where coarse and fine waste steel slag were used as aggregates. The prepared mixtures contained fly ash, sodium hydroxide in solid state, sodium silicate solution, coarse and fine steel slag aggregates as well as water, in which four variables (fly ash, sodium hydroxide, sodium silicate solution, and water) were used as input parameters for modeling. A total number of 210 samples were prepared with target-specified compressive strength at standard age of 28 days of 25, 35, and 45 MPa. Such values were obtained and used as targets for the two AI prediction tools. Evaluation of the model’s performance was achieved via criteria such as mean absolute error (MAE), root mean square error (RMSE), and coefficient of determination (R2). The results showed that both ANN and ANFIS models have strong potential for predicting the compressive strength of GPC but ANFIS (MAE = 1.655 MPa, RMSE = 2.265 MPa, and R2 = 0.879) is better than ANN (MAE = 1.989 MPa, RMSE = 2.423 MPa, and R2 = 0.851). Sensitivity analysis was then carried out, and it was found that reducing one input parameter could only make a small change to the prediction performance.

Synthesis and Characteristics of Inorganic Polymer Materials Geopolymerized from Ash of Brickyard

2019 ◽  
Vol 961 ◽  
pp. 45-50 ◽  
Author(s):  
Hoc Thang Nguyen
Keyword(s):  
Compressive Strength ◽  
Water Absorption ◽  
Sodium Hydroxide ◽  
Sodium Hydroxide Solution ◽  
Raw Material ◽  
Polymer Materials ◽  
Inorganic Polymer ◽  
High Porosity ◽  
Hydroxide Solution ◽  
Geopolymer Paste

Inorganic polymer materials known as geopolymer-based materials are always interesting topics for researchers. Geopolymer is environmentally friendly material which has been potential applications for many different fields such as technical materials, building materials, insolation or refractories, and others. This study used ash of brickyard (AB) as a raw material for geopolymerization process to develop novel materials with high porosity. AB is industrial waste of the brick factories that need to be managed to reduce their negative impact to the environment. AB contains high alumino-silicate resources were mixed with sodium hydroxide solution for 10 minutes to obtain the geopolymer pastes. Sodium hydroxide solution was used as an alkaline activator to form geopolymer paste. The geopolymer paste was filled into 5-cm cube molds according to ASTM C109/C109M 99, and then cured at room temperature for 28 days. These products were then tested for compressive strength, volumetric weight, and water absorption. Results indicated that the material can be considered lightweight with a compressive strength at 28 days that are in the range of 8.1 to 15.4 MPa, volumetric weight around 600kg/m3 and water absorption is under 210.65 kg/m3. The properties of geopolymer products were also determined by analytical techniques that included mineral composition by X Ray Diffraction (XRD) and microstructure by scanning electron microscope (SEM).

Sulfate and Sulfuric Acid Resistance of Geopolymer Mortars Using Waste Blended Ash

2013 ◽  
Vol 61 (3) ◽  
Author(s):  
M. Aamer Rafique Bhutta ◽  
Nur Farhayu Ariffin ◽  
Mohd Warid Hussin ◽  
Nor Hasanah Abdul Shukor Lim
Keyword(s):  
Sulfuric Acid ◽  
Sodium Hydroxide ◽  
Sodium Silicate ◽  
Alkaline Solution ◽  
Sodium Hydroxide Solution ◽  
Sodium Silicate Solution ◽  
Sulfate Solution ◽  
Mass Ratio ◽  
Palm Oil Fuel Ash ◽  
Fuel Ash

This paper presents the chemical resistance of geopolymer mortars prepared from the combination of palm oil fuel ash (POFA) and pulverized fuel ash (PFA) from agro–industrial waste as cement replacement and activated by alkaline solution. Alkaline solution was prepared by combining sodium silicate and sodium hydroxide. The concentration of alkaline solution used was 14 Molar. The optimum mix proportions of geopolymer mortars with PFA: POFA mass ratio of 70:30 was used together with alkaline solution. The ratio of sodium silicate solution–to–sodium hydroxide solution by mass was 2.5:1. The mass ratio of sand to blended ashes was 3:1. Test specimens 70×70×70 mm cube were prepared and cured at room temperature (28°C) for 28–d and heat–cured at 90°C for 24 h, respectively. Then specimens were exposed to 5% sodium sulfate solution and 2% sulfuric acid solution for 28–d, 56–d, 90–d, 180–d and 365–d .The evaluation was done by visual observation, mass change, and loss of compressive strength. The test results revealed that geopolymer mortars showed higher resistance to acids as compared to ordinary Portland cement mortar due to the elimination of cement in the mixture.

Effect of Curing Conditions on the Mechanical Properties of Fly Ash-Based Geopolymer without Sodium Silicate Solution

2014 ◽  
Vol 699 ◽  
pp. 15-19 ◽  
Author(s):  
Rosniza Hanim Abdul Rahim ◽  
Khairun Azizi Azizli ◽  
Zakaria Man ◽  
Muhd Fadhil Nuruddin
Keyword(s):  
Compressive Strength ◽  
Elevated Temperature ◽  
Fly Ash ◽  
Sodium Hydroxide ◽  
Sodium Silicate ◽  
Room Temperature ◽  
Sodium Silicate Solution ◽  
Silicate Solution ◽  
Curing Temperature ◽  
Curing Time

Geopolymer is associated with the alkali activation of materials rich in Si and Al, and alkali activator such as sodium hydroxide is used for the dissolution of raw material with the addition of sodium silicate solution to increase the dissolution process. However, the trend of strength development of geopolymer using sodium hydroxide alone is not well established. This paper presents an evaluation on compressive strength of fly ash–based geopolymer by varying curing time with respect to different curing temperature using sodium hydroxide as the only activator. The samples were cured at room temperature and at an elevated temperature (60°C). Further analysis on the microstructure of geopolymer products cured at 60°C was carried out using Field Emission Scanning Microscopy (FESEM). It can be observed that the compressive strength increased as the curing time increased when cured at room temperature; whereas at elevated temperature, the strength increased up to a maximum 65.28 MPa at 14 days but gradually decreased at longer curing time. Better compressive strength can be obtained when the geopolymer was cured at an elevated temperature compared to curing at room temperature.

A Study on Relationship between Porosity and Compressive Strength for Geopolymer Paste

2013 ◽  
Vol 594-595 ◽  
pp. 1112-1116 ◽  
Author(s):  
Z.F. Farhana ◽  
H. Kamarudin ◽  
Azmi Rahmat ◽  
A.M. Mustafa Al Bakri
Keyword(s):  
Compressive Strength ◽  
Sodium Hydroxide Solution ◽  
Sodium Silicate Solution ◽  
Silicate Solution ◽  
Pulse Velocity ◽  
Strength Test ◽  
Compressive Strength Test ◽  
Alkaline Activator ◽  
The Relationship ◽  
Geopolymer Paste

This paper presents a study on the relationship between porosity and compressive strength for geopolymer paste. In this research, geopolymer paste was made from fly ash class F based geopolymer mixed with alkaline activator; sodium hydroxide solution and sodium silicate solution. Twelve mixes were cast in 50mm x 50mm x 50mm moulds and the samples were cured for 24 hrs at 60 °C in the oven. The samples were examined after 7, 14, 28 and 90 days in terms of porosity test, pulse velocity test and compressive strength test. It was concluded that the sample at day 90 had the highest compressive strength of 56.50 N/mm2had porosity 3.77%. Thus, the sample with lowest porosity had highest pulse velocity 3303 m/s during ultrasonic testing with lowest transmission time 15.17 μs. Keywords: porosity, compression strength, geopolymer, pulse velocity

Effect of Alkaline Activators to Engineering Properties of Geopolymer-Based Materials Synthesized from Red Mud

2018 ◽  
Vol 777 ◽  
pp. 508-512 ◽  
Author(s):  
Van Quang Le ◽  
Minch Quang Do ◽  
Minh Duc Hoang ◽  
Vo Thi Ha Quyen Pham ◽  
Thu Ha Bui ◽  
...  
Keyword(s):  
Sodium Hydroxide ◽  
Sodium Silicate ◽  
Red Mud ◽  
Raw Materials ◽  
Sodium Hydroxide Solution ◽  
Sodium Silicate Solution ◽  
Silicate Solution ◽  
High Heat ◽  
Engineering Properties ◽  
Alumina Production

Geopolymer is an inorganic polymer material formed from alumino-silicate structures. Geopolymer has many outstanding functions in comparison with ordinary materials such as high mechanical strength, high heat and chemical resistance, and lightweight property. The engineering properties of geopolymer-based materials depend on raw materials and synthesized conditions. In which, the aluminosilicate materials having high activity and consisting of many alkaline activators have the possibility of increasing pH in geopolymer paste. In the solution of paste, aluminosilicate compounds are solubilized and then react with alkali-activated ions to form geopolymeric networks. The geopolymer can be synthesized in many different conditions depending on factors of temperature, pressure, and curing conditions. In this study, red mud (RM) was used as the main alumino resource for geopolymerization process. RM is a solid waste residue being left from the mining process of bauxite ores with caustic soda for alumina production. Its disposal remains a global issue in terms of environmental concerns. Formation of RM-based geopolymer was affected by many factors, in which, the alkaline activators are the most important factor. This research was conducted with sodium hydroxide and sodium silicate solutions to elucidate the effect of alkaline activator ratio to the engineering properties of RM-based geopolymers. The results showed that the RM-based geopolymer used sodium silicate solution has more outstanding properties than RM-based geopolymer using sodium hydroxide solution.

Sign in / Sign up

Export Citation Format

Share Document