Synthesis, Structure and Properties of Super Fine LiMn2O4

2010 ◽  
Vol 177 ◽  
pp. 9-11 ◽  
Author(s):  
Jie Song ◽  
Bing Xu ◽  
De Xin Huang ◽  
Cai Xia Li ◽  
Qiang Li

In this paper, super fine LiMn2O4 powder was synthesized by mechanochemical method starting from Li2CO3 and Mn2O3. The structure, size and morphology of LiMn2O4 were explored with X-ray diffraction and scanning electron microscopy (SEM). The electrochemical properties of LiMn2O4 were studied in 2 mol/L (NH4)2SO4 solution. The result showed that pure spinel LiMn204 powder was prepared after 8h grinding with 3.0KW of power and the particle size was about 1µm. Cyclic vohammetry curve indicate LiMn2O4 electrode material has better capacitive performances.

2011 ◽  
Vol 492 ◽  
pp. 256-259
Author(s):  
Jie Song ◽  
Cai Xia Li ◽  
Dan Yu Jiang ◽  
Jin Feng Xia ◽  
Qiang Li

In this paper, super fine Zn2SnO4 powder was synthesized by mechanochemical method starting from ZnO and SnO2. The structure, size and morphology of Zn2SnO4were explored with X-ray diffraction (XRD), scanning electron microscopy (SEM) and nitrogen sorption analysis with the Brunauer-Emmett-Teller (BET) method. The result showed that pure spinel Zn2SnO4 powder was prepared after 2h grinding with 3.0KW of power and the particle size was about 200 nm. The degradation experiment of organic dye was performed by the photocatalytic methods on the light of wavelength (= 365nm). The powder can degrade Alizarin red solution close to 90% under U-V light with a 9W high.


2012 ◽  
Vol 198-199 ◽  
pp. 99-102
Author(s):  
Qing Gang Kong ◽  
Hai Yan Qian

Magnesium nitrate was used as additive for synthesis of Mg(OH)2 (MH) nanoparticles at low temperature (70°C). Mg(OH)2 nanoparticles have platelet-like structure and approximately 40-60nm in thicknesses. X-ray diffraction (XRD) and scanning electron microscopy (SEM) were applied to characterize the crystal phase. The supersaturation degree of solution effects the size and morphology of MH nanoparticles.


2016 ◽  
Vol 680 ◽  
pp. 257-260
Author(s):  
Meng Yun Dong ◽  
Cheng Zhang ◽  
Jin Feng Xia ◽  
Hong Qiang Nian ◽  
Dan Yu Jiang

CaF2 nano-power was prepared by direct precipitation methods with Ca(NO3)2 and KF as raw materials. The influences of presintering temperature and sintering temperature on the particle size and distribution of CaF2 nano-power were studied by X-ray diffraction (XRD) and field-emission scanning electron microscopy (FESEM). This study provided an experimental method for preparation of CaF2 nano-power. The results show that the best presintering temperature of CaF2 nano-power is 500°C and the best sintering temperature of CaF2 ceramic is 900°C.


2010 ◽  
Vol 03 (03) ◽  
pp. 185-188 ◽  
Author(s):  
XIAOYUN ZHAN ◽  
ZHAOHUI LI ◽  
JIAOJUN TANG ◽  
QIZHEN XIAO ◽  
GANGTIE LEI ◽  
...  

Highly crystallized and microsized particles of LiNi0.5Mn1.5O4 spinels with different morphologies have been successfully synthesized using polystyrene (PS) as the sacrificial template, and were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM) and electrochemical measurement. The spinels obtained at 700°C possess abundant porosity with about 200 nm in diameter, while the spinels calcined at 900°C exhibit a well-defined polyhedral morphology with particle size ranged from 0.2 to 2 μm. The materials prepared at 900°C display an excellent cycling performance due probably to better crystallinity and small particle size.


2014 ◽  
Vol 2014 ◽  
pp. 1-10
Author(s):  
Sudarshan Singh ◽  
Sunil B. Bothara

Mucilage isolated from seeds of Manilkara zapota (Linn.) P. Royen syn. is a plant growing naturally in the forests of India. This mucilage is yet to be commercially exploited, and characterized as polymer. Various physicochemical methods like particle size analysis, scanning electron microscopy, thermal analysis, gel permeation chromatography, X-ray diffraction spectrometry, zeta potential, Fourier transform infrared spectroscopy, and nuclear magnetic resonance spectroscopy have been employed to characterize this gum in the present study. Particle size analyses suggest that mucilage has particle size in nanometer. Scanning electron microscopy analysis suggests that the mucilage has irregular particle size. The glass transition temperature of the gum was observed to be 138°C and 136°C by differential scanning calorimetry and differential thermal analysis, respectively. The thermogravimetric analysis suggested that mucilage had good thermal stability. The average molecular weight of mucilage was determined to be 379180, by gel permeation chromatography, while the viscosity of mucilage was observed to be 219.1 cP. The X-ray diffraction spectrometry pattern of the mucilage indicates a completely amorphous structure. Elemental analysis of the gum revealed the contents of carbon, hydrogen, nitrogen, and sulfur to be 80.9 (%), 10.1 (%), 1.58 (%), and 512 (mg/kg), respectively. Mucilage had specific content of calcium, magnesium, potassium, lower concentrations of aluminum, cadmium, cobalt, lead, and nickel. The major functional groups identified from FT-IR spectrum include 3441 cm−1 (–OH), 1660 cm−1 (Alkenyl C–H & C=C Stretch), 1632 cm−1 (–COO–), 1414 cm−1 (–COO–), and 1219 cm−1 (–CH3CO). Analysis of mucilage by paper chromatography and 1D NMR, indicated the presence of rhamnose, xylose, arabinose, mannose, and fructose.


2012 ◽  
Vol 727-728 ◽  
pp. 9-13
Author(s):  
Suzana Arleno S. Santos ◽  
Eduardo Sousa Lima ◽  
Luis Henrique Leme Louro ◽  
Célio Albano da Costa

This study aimed to produce nanometric powders of alumina by sol-gel route. Six samples were produced by varying the amount of water for dilution of aluminum nitrate and the calcination temperature. The final products were evaluated by thermogravimetric analysis, scanning electron microscopy, X-ray diffraction and particle size. It could be noticed that, beyond the time of gelation and calcination temperature, the addition of water also influenced the average size of the clusters.


2011 ◽  
Vol 411 ◽  
pp. 503-507
Author(s):  
Xiao Juan Li ◽  
Zeng Zhe Xi ◽  
Wei Long ◽  
Zhi Gang Zhang ◽  
Jia Zhang

The Bi0.5Na0.5TiO3-xwt%BaTiO3 compound ceramics were prepared. The influence of different BaTiO3 content on structure was evaluated by scanning electron microscopy and X-ray diffraction analysis. The results show oriented is induced by plate-like BaTiO3 template. Signficant improvement of the piezoelectric (d33 = 112 pC/N) and dielectric properties ( max ≈ 5500) was observed. The improvement was attested to the apparent alignment of the BaTiO3 templates and grain oriented growth.


2010 ◽  
Vol 156-157 ◽  
pp. 1010-1013
Author(s):  
Yong Ping Pu ◽  
Yong Yong Zhuang ◽  
Kai Chen ◽  
Ning Xu

Pure MnNb2O6 powders was successfully prepared by hydrothermal method using Nb2O5•nH2O and Mn(NO3)2 as precursors and HCl, HF, NaOH, NH4OH solutions as mineralization agent. The phase composition and morphology of the prepared powder were characterized by X-ray diffraction and scanning electron microscopy. The effect of mineralizers on phase formation was investigated. The results show that the MnNb2O6 powders with crystallite size of ~24nm can be obtained with Mn(NO3)2 and Nb2O5•nH2O as precursors in neutral and alkaline solution at 200 for 168h. The particle size of the MnNb2O6 powder was ~300nm after heat treatment at a temperature of 600 . The SEM photographs show that the morphology of the MnNb2O6 powder are rod-like particles and the MnNb2O6 powders are highly dispersed.


2008 ◽  
Vol 368-372 ◽  
pp. 535-537
Author(s):  
Yu Xing Xu ◽  
Zi Long Tang ◽  
Zhong Tai Zhang

SrTiO3-based voltage-sensitive material was prepared successfully. The structure and properties were investigated using scanning electron microscopy, X-ray diffraction and X-ray photoelectron spectroscopy. It was observed that the average grain size was greater than 3μm and a cubic perovskite structure was obtained. XPS analysis of oxygen indicated that there existed multiform chemical state oxygen at the surface of the grain. Further researches shown that there were a few [AO12] polyhedrons and many cation vacancies in the material discussed, which demonstrated that a lot of oxygen volatilized and a well-known semiconductivity level was achieved.


Author(s):  
Amalia Ekaputri Hidayat ◽  
Setyo Sarwanto Moersidik ◽  
Sandyanto Adityosulindro

Coal burning process in steam powered electric generator plants functioned to generate electricity energy. This process produce kinds of waste, such as solid waste, waste water, and emission. One of the solid waste produced in this process is fly ash. Fly ash is categorized as hazardous waste, it also can buildup in the landfill because of its massive production. However, fly ash has the potential as a raw material to produce synthetic zeolite because it contains metal oxide which is quite high. In this study, class F coal fly ash was synthesized by combining hydrothermal and fusion method. Synthesized fly ash and zeolite are characterized so that the chemical composition can be analyzed by X-ray Fluorescence; the mineralogy analyzed by X-ray Diffraction; the surface morphology analyzed by Scanning Electron Microscopy; and the particle size analyzed by Particle Size Analyzer. The synthesis of zeolite from coal fly ash in this study result hydroxy-sodalite zeolite type. In addition, this synthesis process increases the surface area of the previous fly ash. From the characteristics of zeolite from this synthesis it can be conclude that this zeolite can be approved as an adsorbent for the removal of liquid or gas pollutants in environmental technology applications with further research. ABSTRAKProses yang terjadi pada Pembangkit Listrik Tenaga Uap untuk menghasilkan energi listrik adalah melalui unit proses pembakaran batubara. Proses ini akan menghasilkan limbah padat, cair, maupun udara. Salah satu limbah padat yang dihasilkan adalah abu layang. Limbah abu layang ini dikatagorikan limbah bahan berbahaya dan beracun, serta dapat terjadinya penumpukan di tempat penimbunan akhir karena produksinya yang sangat tinggi. Namun, abu layang memiliki potensi sebagai bahan baku dalam memproduksi zeolit sintetik karena kandungan oksida logamnya yang cukup tinggi. Pada penelitian ini, abu layang batu bara kelas F disintesis dengan metode gabungan fusi-hidrotermal. Abu layang dan zeolit yang disintesis dikarakterisasi agar dapat dianalisis komposisi kimianya dengan X-ray Flourescence; mineraloginya dengan X-ray Diffraction; morfologi permukaan dengan Scanning Electron Microscopy; serta distribusi partikel dengan Particle Size Analyzer. Proses sintesis zeolit dari abu layang batubara pada penelitian ini menghasilkan zeolit jenis hidroksi sodalit. Selain itu, proses sintesis ini meningkatkan luas permukaan dari abu layang sebelumnya. Dari karakteristik zeolit hasil sintesis ini dapat disimpulkan bahwa zeolit ini dapat berpotensi sebagai adsorben untuk penyisihan polutan cair maupun gas pada aplikasi teknologi lingkungan dengan penelitian lebih lanjut.Kata kunci : abu layang; zeolit; hidroxi-sodalit; sintesis; fusi-hidrotermal


Sign in / Sign up

Export Citation Format

Share Document