Effect of Surfactants on the Dispersion of Multi-Walled Carbon Nanotubes in Epoxy Resin

2011 ◽  
Vol 221 ◽  
pp. 1-7 ◽  
Author(s):  
Ying An ◽  
Xue Tao He ◽  
Wei Min Yang ◽  
Yu Mei Ding
Keyword(s):  
Carbon Nanotubes ◽  
Oleic Acid ◽  
Epoxy Resin ◽  
Sodium Dodecyl ◽  
Ammonium Bromide ◽  
Transmission Electron ◽  
Balance State ◽  
Multi Walled Carbon Nanotubes ◽  
Triton X ◽  
Walled Carbon Nanotubes

In order to improve the dispersion homogeneity and stabilization of multi-walled carbon nanotubes (MWNT) in epoxy resin, the effect of different surfactants such as hexadecyl trimethyl ammonium bromide (HTAB), sodium dodecyl sulfate (SDS), oleic acid, Triton X-100 and BYK-9077 on the dispersion of MWNT were investigated. Suspensions of MWNTs/epoxy resin with various surfactants were prepared by ultrasonic agitation. Dispersion homogeneity of MWNT in epoxy resin was evaluated by transmission electron microscopy (TEM), and dispersion stabilization was evaluated by stationary observation. The results show that dispersion properties were not improved by HTAB, while they were improved incoordinately by SDS, oleic acid, Triton X-100 and BYK-9077. Suspensions of MWNTs/epoxy resin with HTAB, SDS, oleic acid and Triton X-100 were all delaminated quickly, it means, dispersion stabilization were not improved by these surfactants. BYK-9077 was the only surfactant which enhanced the dispersion homogeneity and stabilization of MWNTs/epoxy resin significantly. Based on this research, various weight ratios of surfactant BYK-9077 to MWNT were studied. The experimental results show that the dispersion system could reach a balance state when the ratio of surfactant BYK-9077 to MWN was 2.

Investigation of Surfactant Type, Dosage and Ultrasonication Temperature Control on Dispersity of Metal-Coated Multi-Walled Carbon Nanotubes

2016 ◽  
Vol 16 (4) ◽  
pp. 4224-4232
Author(s):  
Xiaoning Liang ◽  
Wei Li
Keyword(s):  
Carbon Nanotubes ◽  
Oleic Acid ◽  
Sodium Dodecyl ◽  
Sodium Dodecyl Benzene Sulfonate ◽  
Negative Effects ◽  
Ultrasonic Dispersion ◽  
Dispersion Process ◽  
Ultrasonic Assisted ◽  
Multi Walled Carbon Nanotubes ◽  
Walled Carbon Nanotubes

We studied the dispersity of multi-walled carbon nanotubes (MWNTs) combined with different metallic particles (Ni and Fe). An ultrasonic-assisted water-bath dispersion process was used to disperse the metal-coated MWNTs in different solutions and the dispersity was measured using an ultraviolet-visible spectrophotometer. The dispersity and morphology of the MWNTs were characterized using field-emission scanning electron microscopy (FE-SEM) together with digital image processing technology. Effects of dispersant type (sodium dodecyl benzene sulfonate (SDBS), oleic acid, and polymer (TNEDIS)) and surfactant dosage on the dispersity of the metal-coated MWNTs were investigated under controlled and uncontrolled temperatures and results were compared with those from the untreated MWNTs. The results showed that the negative effects of temperature on the ultrasonic dispersion process could be eliminated through a temperature-controlled system. Moreover, the TNEDIS, SDBS, and oleic acid were arranged in the descending order of the dispersion effect degree. The untreated MWNTs, Ni-coated MWNTs, and Fe-coated MWNTs were arranged in the descending degree of dispersity order. Since the metal coating makes the MWNTs harder and more fragile, the metal-coated MWNTs are more likely to fracture during the ultrasonic dispersion process.

scholarly journals Biocompatibility Characteristics of Titanium Coated with Multi Walled Carbon Nanotubes—Hydroxyapatite Nanocomposites

Materials ◽  
2019 ◽  
Vol 12 (2) ◽  
pp. 224 ◽  
Author(s):  
Jung-Eun Park ◽  
Yong-Seok Jang ◽  
Tae-Sung Bae ◽  
Min-Ho Lee
Keyword(s):  
Electron Microscopy ◽  
Carbon Nanotubes ◽  
Sol Gel ◽  
Pure Titanium ◽  
Cell Proliferation And Differentiation ◽  
Transmission Electron ◽  
Proliferation And Differentiation ◽  
Multi Walled Carbon Nanotubes ◽  
Walled Carbon Nanotubes

Multi walled carbon nanotubes-hydroxyapatite (MWCNTs-HA) with various contents of MWCNTs was synthesized using the sol-gel method. MWCNTs-HA composites were characterized by X-ray diffraction (XRD) and transmission electron microscopy (TEM). HA particles were generated on the surface of MWCNT. Produced MWCNTs-HA nanocomposites were coated on pure titanium (PT). Characteristic of the titanium coated MWCNTs-HA was evaluated by field-emission scanning electron microscopy (FE-SEM) and XRD. The results show that the titanium surface was covered with MWCNTs-HA nanoparticles and MWCNTs help form the crystalized hydroxyapatite. Furthermore, the MWCNTs-HA coated titanium was investigated for in vitro cellular responses. Cell proliferation and differentiation were improved on the surface of MWCNT-HA coated titanium.

scholarly journals The effect of the surface modification of carbon nanotubes on their dispersion in the epoxy matrix

2011 ◽  
Vol 13 (2) ◽  
pp. 62-69 ◽  
Author(s):  
Maria Wladyka-Przybylak ◽  
Dorota Wesolek ◽  
Weronika Gieparda ◽  
Anna Boczkowska ◽  
Ewelina Ciecierska
Keyword(s):  
Carbon Nanotubes ◽  
Surface Modification ◽  
Epoxy Resin ◽  
Epoxy Matrix ◽  
Mechanical Mixing ◽  
Weight Percentage ◽  
Homogeneous Dispersion ◽  
Multi Walled Carbon Nanotubes ◽  
Mixing Method ◽  
Walled Carbon Nanotubes

The effect of the surface modification of carbon nanotubes on their dispersion in the epoxy matrix Functionalization of multi-walled carbon nanotubes (MWCNTs) has an effect on the dispersion of MWCNT in the epoxy matrix. Samples based on two kinds of epoxy resin and different weight percentage of MWCNTs (functionalized and non-functionalized) were prepared. Epoxy/carbon nanotubes composites were prepared by different mixing methods (ultrasounds and a combination of ultrasounds and mechanical mixing). CNTs modified with different functional groups were investigated. Surfactants were used to lower the surface tension of the liquid, which enabled easier spreading and reducing the interfacial tension. Solvents were also used to reduce the liquid viscosity. Some of them facilitate homogeneous dispersion of nanotubes in the resin. The properties of epoxy/nanotubes composites strongly depend on a uniform distribution of carbon nanotubes in the epoxy matrix. The type of epoxy resin, solvent, surfactant and mixing method for homogeneous dispersion of CNTs in the epoxy matrix was evaluated. The effect of CNTs functionalization type on their dispersion in the epoxy resins was evaluated on the basis of viscosity and microstructure studies.

scholarly journals Enhancement of out-of-plane mechanical properties of carbon fiber reinforced epoxy resin composite by incorporating the multi-walled carbon nanotubes

2021 ◽  
Vol 3 (6) ◽  
Author(s):  
Seyed Ali Mirsalehi ◽  
Amir Ali Youzbashi ◽  
Amjad Sazgar
Keyword(s):  
Mechanical Properties ◽  
Carbon Nanotubes ◽  
Tensile Test ◽  
Epoxy Resin ◽  
Laminate Composite ◽  
Filament Winding ◽  
Hybrid Nanocomposites ◽  
Out Of Plane ◽  
Multi Walled Carbon Nanotubes ◽  
Walled Carbon Nanotubes

AbstractIn this study, epoxy hybrid nanocomposites reinforced by carbon fibers (CFs) were fabricated by a filament winding. To improve out-of-plane (transverse) mechanical properties, 0.5 and 1.0 Wt.% multi-walled carbon nanotubes (MWCNTs) were embedded into epoxy/CF composites. The MWCNTs were well dispersed into the epoxy resin without using any additives. The transverse mechanical properties of epoxy/MWCNT/CF hybrid nanocomposites were evaluated by the tensile test in the vertical direction to the CFs (90º tensile) and flexural tests. The fracture surfaces of composites were studied by scanning electron microscopy (SEM). The SEM observations showed that the bridging of the MWCNTs is one of the mechanisms of transverse mechanical properties enhancement in the epoxy/MWCNT/CF composites. The results of the 90º tensile test proved that the tensile strength and elongation at break of nanocomposite with 1.0 Wt.% MWCNTs improved up to 53% and 50% in comparison with epoxy/CF laminate composite, respectively. Furthermore, the flexural strength, secant modulus, and elongation of epoxy/1.0 Wt.% MWCNT/CF hybrid nanocomposite increased 15%, 7%, and 9% compared to epoxy/CF laminate composite, respectively.

Characterization of Mechanical and Viscoelastic Properties of SC-15 Epoxy Nanocomposites Reinforced With Multi-Walled Carbon Nanotubes, Nanoclay and Binary Nanoparticles

2014 ◽  
Author(s):  
Tanjheel H. Mahdi ◽  
Mohammad E. Islam ◽  
Mahesh V. Hosur ◽  
Alfred Tcherbi-Narteh ◽  
S. Jeelani
Keyword(s):  
Carbon Nanotubes ◽  
Epoxy Resin ◽  
Viscoelastic Properties ◽  
Flexural Modulus ◽  
Epoxy Nanocomposites ◽  
Multiwalled Carbon ◽  
Epoxy Resin System ◽  
Multi Walled Carbon Nanotubes ◽  
Walled Carbon Nanotubes ◽  
Binary Nanoparticles

Mechanical and viscoelastic properties of polymer nanocomposites reinforced with carboxyl functionalized multiwalled carbon nanotubes (COOH-MWCNT), montmorillonite nanoclays (MMT) and MWCNT/MMT binary nanoparticle were investigated. In this study, 0.3 wt. % of COOH-MWCNT, 2 wt. % of MMT and 0.1 wt. % COOH-MWCNT/2 wt. % MMT binary nanoparticles by weight of epoxy were incorporated to modify SC-15 epoxy resin system. The nanocomposites were subjected to flexure test, dynamic mechanical and thermomechanical analyses. Morphological study was conducted with scanning electron microscope. Addition of each of the nanoparticles in epoxy showed significant improvement in mechanical and viscoelastic properties compared to those of control ones. But, best results were obtained for addition of 0.1% MWCNT/2% MMT binary nanoparticles in epoxy. Nanocomposites modified with binary nanoparticles exhibited about 20% increase in storage modulus as well as 25° C increase in glass transition temperature. Flexural modulus for binary nanoparticle modified composites depicted about 30% improvement compared to control ones. Thus, improvement of mechanical and viscoelastic properties was achieved by incorporating binary nanoparticles to epoxy nanocomposites. The increase in properties was attributed to synergistic effect of MWCNTs and nanoclay in chemically interacting with each other and epoxy resin as well as in arresting and delaying the crack growth once initiated.

scholarly journals Carbon Nanofibers from Carbon Nanotubes by 1.2 keVAr+Sputtering at Room Temperature

2014 ◽  
Vol 2014 ◽  
pp. 1-5 ◽  
Author(s):  
Shuang-Xi Xue ◽  
Qin-Tao Li ◽  
Xian-Rui Zhao ◽  
Qin-Yi Shi ◽  
Zhi-Gang Li ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Carbon Nanotubes ◽  
Carbon Nanofibers ◽  
Carbon Nanoparticles ◽  
Room Temperature ◽  
Ion Irradiation ◽  
Transmission Electron ◽  
Multi Walled Carbon Nanotubes ◽  
Walled Carbon Nanotubes ◽  
Carbon Nanowires

Multi-walled carbon nanotubes (MWCNTs) were irradiated by 1.2 keV Ar ion beams for 15–60 min at room temperature with current density of 60 µA/cm2. The morphology and microstructure are investigated by scanning electron microscopy, transmission electron microscopy and Raman spectroscopy. The results show that carbon nanofibers are achieved after 60 min ion irradiation and the formation of carbon nanofibers proceeds through four periods, carbon nanotubes—amorphous carbon nanowires—carbon nanoparticles along the tube axis—conical protrusions on the nanoparticles surface—carbon nanofibers from the conical protrusions.

Sign in / Sign up

Export Citation Format

Share Document