B4C/5083 Al Composite Prepared by Cryomilling

2011 ◽  
Vol 233-235 ◽  
pp. 1825-1829
Author(s):  
Bin Hao ◽  
Ji Shan Zhang ◽  
Da Cheng Liu
Keyword(s):  
Composite Powder ◽  
Milling Time ◽  
Hot Extrusion ◽  
Coarse Grained ◽  
Coarse Grain ◽  
X Ray Diffraction ◽  
X Ray ◽  
Blended Powder ◽  
Al Composite ◽  
B4c Particles

In the present investigation, the composite powder with 20wt.% particulate B4C and 80wt.% nanocrystalline 5083 Al was fabricated using mechanically milling at cryogenic temperature (cryomilling). After this, the cryomilled composite powder was homogeneously blended with an equal amount of unmilled coarse-grained 5083 Al. The blended powder was consolidated with hot-pressing at 500°C, followed by hot extrusion at 410°C. The consolidated composite consists of 10wt.% B4C, 50wt.% coarse grain 5083 Al and the balance nanocrystalline 5083 Al. The microstructure evolution of the composite during cryomilling and consolidation was investigated by X-ray diffraction (XRD), optical microscopy (OM) and scanning electron microscopy (SEM). The results show that the particle size of the cryomilled composite powder became smaller and then bigger with milling time longer. This demonstrates the course rely mainly on broken first, and then rely mainly on cold welding with milling time longer. B4C particles can be distributed in 5083 Al matrix uniformly. In addition, the presence of oxygen and nitrogen in cryomilled powders has been demonstrated in this paper.

Mechanical properties of FeAlSi powders prepared by mechanical alloying from different initial feedstock materials

2019 ◽  
Vol 107 (2) ◽  
pp. 207 ◽  
Author(s):  
Jaroslav Čech ◽  
Petr Haušild ◽  
Miroslav Karlík ◽  
Veronika Kadlecová ◽  
Jiří Čapek ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Mechanical Alloying ◽  
Young’S Modulus ◽  
Milling Time ◽  
Young's Modulus ◽  
Element Model ◽  
X Ray Diffraction ◽  
X Ray ◽  
Powder Particles ◽  
Complete Homogenization

FeAl20Si20 (wt.%) powders prepared by mechanical alloying from different initial feedstock materials (Fe, Al, Si, FeAl27) were investigated in this study. Scanning electron microscopy, X-ray diffraction and nanoindentation techniques were used to analyze microstructure, phase composition and mechanical properties (hardness and Young’s modulus). Finite element model was developed to account for the decrease in measured values of mechanical properties of powder particles with increasing penetration depth caused by surrounding soft resin used for embedding powder particles. Progressive homogenization of the powders’ microstructure and an increase of hardness and Young’s modulus with milling time were observed and the time for complete homogenization was estimated.

scholarly journals Mechanochemical Preparation of Slow Release Fertilizer Based on Glauconite–Urea Complexes

Minerals ◽  
2019 ◽  
Vol 9 (9) ◽  
pp. 507 ◽  
Author(s):  
Maxim Rudmin ◽  
Elshan Abdullayev ◽  
Alexey Ruban ◽  
Ales Buyakov ◽  
Bulat Soktoev
Keyword(s):  
Milling Time ◽  
Slow Release ◽  
Mechanochemical Activation ◽  
Structural Characteristics ◽  
Fluorescence Analysis ◽  
Planetary Mill ◽  
X Ray Diffraction ◽  
Mechanochemical Method ◽  
X Ray ◽  
Slow Release Fertilizers

We investigated the mechanochemical synthesis of complex slow release fertilizers (SRF) derived from glauconite. We studied the effectiveness of the mechanical intercalation of urea into glauconite using planetary and ring mills. The potassium-nitric complex SRFs were synthesized via a mechanochemical method mixing glauconite with urea in a 3:1 ratio. The obtained composites were analyzed using X-ray diffraction analysis, scanning electron microscopy, X-ray fluorescence analysis, and infrared spectroscopy. The results show that as duration of mechanochemical activation increases, the mineralogical, chemical, and structural characteristics of composites change. Essential modifications associated with a decrease in absorbed urea and the formation of microcrystallites were observed when the planetary milling time increased from 5 to 10 min and the ring milling from 15 to 30 min. Complete intercalation of urea into glauconite was achieved by 20 min grinding in a planetary mill or 60 min in a ring mill. Urea intercalation in glauconite occurs much faster when using a planetary mill compared to a ring mill.

scholarly journals Multiscale Copper-µDiamond Nanostructured Composites

2012 ◽  
Vol 730-732 ◽  
pp. 925-930
Author(s):  
Daniela Nunes ◽  
Vanessa Livramento ◽  
Horácio Fernandes ◽  
Carlos Silva ◽  
Nobumitsu Shohoji ◽  
...  
Keyword(s):  
Pure Copper ◽  
Thermal Stabilization ◽  
Hot Extrusion ◽  
Processing Parameters ◽  
High Energy ◽  
X Ray Diffraction ◽  
X Ray ◽  
Optimal Processing ◽  
Novel Approach ◽  
Transmission Electron

Nanostructured copper-diamond composites can be tailored for thermal management applications at high temperature. A novel approach based on multiscale diamond dispersions is proposed for the production of this type of materials: a Cu-nDiamond composite produced by high-energy milling is used as a nanostructured matrix for further dispersion of micrometer sized diamond. The former offers strength and microstructural thermal stability while the latter provides high thermal conductivity. A series of Cu-nDiamond mixtures have been milled to define the minimum nanodiamond fraction suitable for matrix refinement and thermal stabilization. A refined matrix with homogenously dispersed nanoparticles could be obtained with 4 at.% nanodiamond for posterior mixture with mDiamond and subsequent consolidation. In order to define optimal processing parameters, consolidation by hot extrusion has been carried out for a Cu-nDiamond composite and, in parallel, for a mixture of pure copper and mDiamond. The materials produced were characterized by X-ray diffraction, scanning and transmission electron microscopy and microhardness measurements.

Development of WC-Fe3Al Composites by Spark Plasma Sintering Process

2016 ◽  
Vol 881 ◽  
pp. 307-312
Author(s):  
Luis Antonio C. Ybarra ◽  
Afonso Chimanski ◽  
Sergio Gama ◽  
Ricardo A.G. da Silva ◽  
Izabel Fernanda Machado ◽  
...  
Keyword(s):  
Spark Plasma Sintering ◽  
Zinc Stearate ◽  
Sintering Process ◽  
X Ray Diffraction ◽  
X Ray ◽  
Plasma Sintering ◽  
Al Composite ◽  
Spark Plasma ◽  
Short Time ◽  
Vibration Mill

Tungsten carbide (WC) based composites are usually produced with cobalt, but this binder has the inconvenience of shortage, unstable price and potential carcinogenicity. The objective of this study was to develop WC composite with intermetallic Fe3Al matrix. Powders of WC, iron and aluminum, with composition WC-10 wt% Fe3Al, and 0.5 wt% zinc stearate were milled in a vibration mill for 6 h and sintered in a SPS (spark plasma sintering) furnace at 1150 °C for 8 min under pressure of 30 MPa. Measured density and microstructure analysis showed that the composite had significant densification during the (low-temperature, short time) sintering, and X-ray diffraction analysis showed the formation of intermetallic Fe3Al. Analysis by Vickers indentation resulted in hardness of 11.2 GPa and fracture toughness of 24.6 MPa.m1/2, showing the feasibility of producing dense WC-Fe3Al composite with high mechanical properties using the SPS technique.

On the Mechanical Milling of the AlCuFe Icosahedral Phase with Water

2014 ◽  
Vol 793 ◽  
pp. 23-27
Author(s):  
C. Patiño-Carachure ◽  
J. Luis López-Miranda ◽  
F. de la Rosa ◽  
M. Abatal ◽  
R. Pérez ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Milling Time ◽  
Induction Furnace ◽  
Icosahedral Phase ◽  
Quasicrystalline Phase ◽  
X Ray Diffraction ◽  
Cast Sample ◽  
X Ray ◽  
Transmission Electron ◽  
Icosahedral Quasicrystalline

In this investigation the Al64Cu24Fe12 alloy was melted in an induction furnace and solidified under normal casting conditions. The as-cast sample was subject to a heat treatment at 700 oC under argon atmosphere in order to obtain the icosahedral quasicrystalline phase in a monophase region. Subsequently, the icosahedral phase was milled for different times and water added conditions. The pre-alloyed and milled powders were characterized using scanning electron microscopy, X-Ray diffraction, and transmission electron microscopy. The experimental results showed that the icosahedral phase is sensitive to the reaction between water and aluminum of the quasicrystalline alloy to generate hydrogen. As the milling time and the amount of water are increased, the embrittlement reaction of the alloy is accentuated releasing more hydrogen.

Microstructure Evolution of a Fine Grain Al-50wt%Si Alloy Fabricated by High Energy Milling

2011 ◽  
Vol 479 ◽  
pp. 54-61 ◽  
Author(s):  
Fei Wang ◽  
Ya Ping Wang
Keyword(s):  
Grain Growth ◽  
Microstructure Evolution ◽  
Room Temperature ◽  
Milling Time ◽  
High Energy ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
Laser Method ◽  
X Ray ◽  
Fine Grain

Microstructure evolution of high energy milled Al-50wt%Si alloy during heat treatment at different temperature was studied. Scanning electron microscope (SEM) and X-ray diffraction (XRD) results show that the size of the alloy powders decreased with increasing milling time. The observable coarsening of Si particles was not seen below 730°C in the high energy milled alloy, whereas, for the alloy prepared by mixed Al and Si powders, the grain growth occurred at 660°C. The activation energy for the grain growth of Si particles in the high energy milled alloy was determined as about 244 kJ/mol by the differential scanning calorimetry (DSC) data analysis. The size of Si particles in the hot pressed Al-50wt%Si alloy prepared by high energy milled powders was 5-30 m at 700°C, which was significantly reduced compared to that of the original Si powders. Thermal diffusivity of the hot pressed Al-50wt%Si alloy was 55 mm2/s at room temperature which was obtained by laser method.

Microstructure Evolution and Mossbauer Spectroscopy Research of Nanostructured Ni3 Fe Intermetallic

2021 ◽  
Vol 32 ◽  
pp. 1-13
Author(s):  
Amel Kaibi ◽  
Abderrahim Guittoum ◽  
Nassim Souami ◽  
Mohamed Kechouane
Keyword(s):  
Magnetic Field ◽  
Mössbauer Spectroscopy ◽  
Mössbauer Spectra ◽  
Milling Time ◽  
Mossbauer Spectroscopy ◽  
Hyperfine Magnetic Field ◽  
X Ray Diffraction ◽  
X Ray ◽  
Mossbauer Spectra ◽  
Mößbauer Spectroscopy

Nanocrystalline Ni75Fe25 (Ni3Fe) powders were prepared by mechanical alloying process using a vario-planetary high-energy ball mill. The intermetallic Ni3Fe formation and different physical properties were investigated, as a function of milling time, t, (in the range 6 to 96 h range), using X-Ray Diffraction (XRD) and Mössbauer Spectroscopy techniques. X-ray diffraction were performed on the samples to understand the structural characteristics and get information about elements and phases present in the powder after different time of milling. The refinement of XRD spectra revealed the complete formation of fcc Ni (Fe) disordered solid solution after 24 h of milling time, the Fe and Ni elemental distributions are closely correlated. With increasing the milling time, the lattice parameter increases and the grains size decreases. The Mössbauer experiments were performed on the powders in order to follow the formation of Ni3Fe compound as a function of milling time. From the adjustment of Mössbauer spectra, we extracted the hyperfine parameters. The evolution of hyperfine magnetic field shows that the magnetic disordered Ni3Fe phase starts to form from 6 h of milling time and grow in intensity with milling time. For the milling time more than 24 h, only the Ni3Fe disordered phase is present with a mean hyperfine magnetic field of about 29.5 T. The interpretation of the Mossbauer spectra confirmed the results obtained by XRD.

The Synthesis of Cu0.81Ni0.19 Intermetallics by Mechanical Alloying

2012 ◽  
Vol 496 ◽  
pp. 379-382
Author(s):  
Rui Song Yang ◽  
Ming Tian Li ◽  
Chun Hai Liu ◽  
Xue Jun Cui ◽  
Yong Zhong Jin
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Grain Size ◽  
Mechanical Alloying ◽  
Milling Time ◽  
Elemental Powder ◽  
X Ray Diffraction ◽  
X Ray ◽  
Scherrer Equation ◽  
Scanning Electron

The Cu0.81Ni0.19 has been synthesized directly from elemental powder of nickel and copper by mechanical alloying. The alloyed Cu0.81Ni0.19 alloy powders are prepared by milling of 8h. The grain size calculated by Scherrer equation of the NiCu alloy decreased with the increasing of milling time. The end-product was analyzed by X-ray diffraction (XRD), scanning electron microscopy (SEM)

Characterization of the Phase Transformations in the Shape Memory Alloy Ni-36 at.% Al

1991 ◽  
Vol 246 ◽  
Author(s):  
J.A. Horton ◽  
E.P. George ◽  
C.J. Sparks ◽  
M.Y. Kao ◽  
O.B. Cavin ◽  
...  
Keyword(s):  
High Temperature ◽  
Shape Memory ◽  
Phase Transformations ◽  
Hot Extrusion ◽  
Exothermic Peak ◽  
Nickel Aluminum ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
X Ray ◽  
Transmission Electron

AbstractA survey by differential scanning calorimetry (DSC) and recovery during heating of indentations on a series of nickel-aluminum alloys showed that the Ni-36 at.% Al composition has the best potential for a recoverable shape memory effect at temperatures above 100°C. The phase transformations were studied by high temperature transmission electron microscopy (TEM) and by high temperature x-ray diffraction (HTXRD). Quenching from 1200°C resulted in a single phase, fully martensitic structure. The initial quenched-in martensites were found by both TEM and X-ray diffraction to consist of primarily a body centered tetragonal (bct) phase with some body centered orthorhombic (bco) phase present. On the first heating cycle, DSC showed an endothermic peak at 121°C and an exothermic peak at 289°C, and upon cooling a martensite exothermic peak at 115° C. Upon subsequent cycles the 289°C peak disappeared. High temperature X-ray diffraction, with a heating rate of 2°C/min, showed the expected transformation of bct phase to B2 between 100 and 200°C, however the bco phase remained intact. At 400 to 450°C the B2 phase transformed to Ni2Al and Ni5Al3. During TEM heating experiments a dislocation-free martensite transformed reversibly to B2 at temperatures less than 150°C. At higher temperatures (nearly 600°C) 1/3, 1/3, 1/3 reflections from an ω-like phase formed. Upon cooling, the 1/3, 1/3, 1/3 reflections disappeared and a more complicated martensite resulted. Boron additions suppressed intergranular fracture and, as expected, resulted in no ductility improvements. Boron additions and/or hot extrusion encouraged the formation of a superordered bct structure with 1/2, 1/2, 0 reflections.

Sign in / Sign up

Export Citation Format

Share Document